brc z330 operating instructions (1)

8/16/2019 BRC Z330 Operating Instructions (1)

1/73

Sony Corporation Printed in Japan

Printed on recycled paper.

HD ColorVideo Camera

Operating InstructionsBefore operating the unit, please read this manual thoroughlyand retain it for future reference.

BRC-Z330

4-149-933- 11 (1)

© 2009 Sony Corporation


2/73

2

Owner’s RecordThe model and serial numbers are located on the bottom.Record these numbers in the spaces provided below.Refer to these numbers whenever you call upon yourSony dealer regarding this product.

Model No. BRC-Z330Serial No.

To reduce the risk of fire or electricshock, do not expose this apparatus torain or moisture.

To avoid electrical shock, do not open thecabinet. Refer servicing to qualifiedpersonnel only.

WARNINGUse the Sony MPA-AC1 AC power adapter providedwith this equipment as a power supply source. Any otherpower sources may result in hazards such as a fire.This product has no power switch.Disconnect device of this equipment is the mains plug ofthe AC adapter.The mains plug on this equipment must be used todisconnect mains power.Please ensure that the socket outlet is installed near theequipment and shall be easily accessible.In the event of abnormal operations, disconnect themains plug.

WARNING (For Installers only)Instruction for installing the equipment on the ceiling:After the installation, ensure the connection is capableof supporting four times the weight of the equipmentdownwards.

WARNINGThis unit has no power switch.When installing the unit, incorporate a readilyaccessible disconnect device in the fixed wiring, orconnect the power plug to an easily accessible socket-outlet near the unit.

If a fault should occur during operation of the unit,operate the disconnect device to switch the powersupply off, or disconnect the power plug.

IMPORTANTThe nameplate is located on the bottom.

For the customers in the U.S.A.This equipment has been tested and found to complywith the limits for a Class A digital device, pursuant toPart 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmfulinterference when the equipment is operated in a

commercial environment. This equipment generates,uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructionmanual, may cause harmful interference to radiocommunications. Operation of this equipment in aresidential area is likely to cause harmful interference inwhich case the user will be required to correct theinterference at his own expense.

You are cautioned that any changes or modifications notexpressly approved in this manual could void yourauthority to operate this equipment.

All interface cables used to connect peripherals must beshielded in order to comply with the limits for a digitaldevice pursuant to Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received,including interference that may cause undesiredoperation.

For the customers in CanadaThis Class A digital apparatus complies with CanadianICES-003.

For the customers in Europe, Australia andNew Zealand

WARNINGThis is a Class A product. In a domestic environment,this product may cause radio interference in which casethe user may be required to take adequate measures.In the case that interference should occur, consult yournearest authorized Sony service facility.

For the customers in EuropeThe manufacturer of this product is Sony Corporation,1-7-1 Konan, Minato-ku, Tokyo, Japan.The Authorized Representative for EMC and productsafety is Sony Deutschland GmbH, Hedelfinger Strasse61, 70327 Stuttgart, Germany.

This apparatus shall not be used in the residential area.

WARNING


3/73Table of Contents 3

Table of Contents

Getting StartedPrecautions ............................................................. 5Phenomena Specific to CMOS Image Sensors .... 6

OverviewFeatures .................................................................. 7System Components .............................................. 8

Supplied Components and Accessories .............. 8Optional Products ............................................... 9

System Configuration .......................................... 10Operating a BRC-Z330 Camera Using the

Supplied Remote Commander ....................... 10Operating a BRC-Z330 Camera Using the RM-

BR300 Remote Control Unit .......................... 10Operating Multiple BRC-Z330 Cameras Using the

RM-BR300 Remote Control Unit .................. 11Operating Multiple BRC-Z330 Cameras Using the

BRS-200 Remote Camera OperatingSwitcher .......................................................... 12

Location and Function of Parts .......................... 13Camera ............................................................. 13Remote Commander (supplied) ....................... 15RM-BR300 Remote Control Unit (not

supplied) ......................................................... 16

BRBK-HD2 HD-SDI Output Card (notsupplied) ......................................................... 19

Adjusting and Setting With MenusAbout On-Screen Menus ..................................... 20

Main Menu .......................................................20Setting Menus ................................................... 20

Operation Through Menus ................................. 21Menu Operation Using the Supplied Remote

Commander .................................................... 21Menu Operation Using the RM-BR300 Remote

Control Unit ................................................... 22EXPOSURE Menu .............................................. 23COLOR Menu ..................................................... 24PICTURE Menu .................................................. 25FOCUS Menu ...................................................... 26PAN TILT ZOOM Menu .................................... 27SYSTEM Menu .................................................... 28VIDEO OUT Menu ............................................. 29STATUS Menu ..................................................... 30

Operation Using the SuppliedRemote CommanderTurning on the Power ..........................................31Pan/Tilt and Zoom Operation .............................32

Panning and Tilting ...........................................32Zooming ............................................................33Operating Multiple Cameras with the Remote

Commander .....................................................33Adjusting the Camera ..........................................33

Focusing on a Subject .......................................33Shooting with Back Lighting ............................34

Storing the Camera Settings in Memory– Presetting Feature .............................................34

Operation Using the RM-BR300Remote Control UnitTurning on the Power ..........................................36

Operating Multiple Cameras .............................36Pan/Tilt and Zoom Operation .............................37

Panning and Tilting ...........................................37Zooming ............................................................39

Adjusting the Camera ..........................................39Focusing on a Subject .......................................39Shooting with Back Lighting ............................40Adjusting the White Balance ............................40Adjusting the Brightness ...................................40

Storing the Camera Settings in Memory– Presetting Feature .............................................41

Storing Camera Settings ...................................41Setting the Speed of the Camera Moving to a

Preset Position ................................................42

Installation and ConnectionsInstallation ............................................................43

Attaching an Output Card .................................43Installing the Camera ........................................43Installing the Camera in a High Position ..........44

Connections ..........................................................51Connecting to an AC Outlet ..............................51Connecting the RM-BR300 Remote Control

Unit .................................................................51Connecting a Monitor, etc. Equipped with the

Analog Component (YPbPr) InputConnector ........................................................52

Connecting a Device Equipped with VISCA RS-232C Connector ..............................................53

Connecting a Device Equipped with VISCA RS-422 Connector .................................................53

http://-/?-http://-/?-


4/73Table of Contents4

Connecting a Video Monitor, VTR, etc. Equippedwith Composite Video or S Video InputConnector ....................................................... 54

Connecting a VTR Equipped with HD-SDI InputConnectors ..................................................... 55

Connecting a Sync Signal Generator ............... 55

AppendixList of Messages ................................................... 57Troubleshooting ................................................... 58Menu Configuration ............................................ 60Presetting Items ................................................... 64Specifications ....................................................... 66

Dimensions ....................................................... 68Pin Assignments ............................................... 70Wiring Diagram of VISCA RS-422

Connection ..................................................... 72Using the VISCA RS-422 Connector Plug ...... 73


5/73

G e t t i n g S t ar t e d

Precautions 5

Getting Started

Precautions

Operating or storage locationOperating or storing the camera in the followinglocations may cause damage to the camera:– Extremely hot or cold places (Operating

temperature: 0 °C to 40 °C [32 °F to 104 °F])– Exposed in direct sunlight for a long time, or close

to heating equipment (e.g., near heaters)– Close to sources of strong magnetism– Close to sources of powerful electromagnetic

radiation, such as radios or TV transmitters– Locations subject to strong vibration or shock

• Use of a mobile phone close to this camera may cause

a malfunction of the camera or affect the quality ofimages. You are cautioned to turn off any mobilephone near the camera.

• Never expose the lens to the sun or other stronglight source.Exposing the lens to the sun or other strong lightsource may cause damage to internal parts fromconcentrated light. When the camera is not be used,keep it out of direct sunlight and other strong light orprotect it with a lens cover.

Ventilation

To prevent heat buildup, do not block air circulationaround the camera.

TransportationWhen transporting the camera, repack it as originallypacked at the factory or in materials equal in quality.

Cleaning• Use a blower to remove dust from the lens or optical

filter.• Use a soft, dry cloth to clean the external surfaces of

the camera. Stubborn stains can be removed using asoft cloth dampened with a small quantity of detergentsolution, then wipe dry.

• Do not use volatile solvents such as alcohol, benzeneor thinners as they may damage the surface finishes.

The pan/tilt mechanismDo not disturb pan/tilt movement while power issupplied to the camera. Doing so may cause damage ormalfunction.

MaintenanceThe camera mechanism may cause abnormal noise dueto wear and lubrication loss after a long period of use. Tomaintain optimum performance, we recommendperiodical maintenance. If abnormal noise occurs,consult with your Sony dealer.

Note on laser beamsLaser beams may damage a CMOS image sensor. You arecautioned that the surface of a CMOS image sensor shouldnot be exposed to laser beam radiation in an environmentwhere a laser beam device is used.


6/73

Get t i ngS t ar t ed

Phenomena Specific to CMOS Image Sensors6

Phenomena Specific toCMOS Image SensorsThe following phenomena that may appear in images arespecific to CMOS (Complementary Metal OxideSemiconductor) image sensors. They do not indicate

malfunctions.White flecksAlthough the CMOS image sensors are produced withhigh-precision technologies, fine white flecks may begenerated on the screen in rare cases, caused by cosmicrays, etc. This is related to the principle of CMOS imagesensors and is not a malfunction.

The white flecks especially tend to be seen in thefollowing cases:• when operating at a high environmental temperature• when you have raised the gain (sensitivity)

This symptom may be improved by turning the cameraoff and then on again.

AliasingWhen fine patterns, stripes, or lines are shot, they mayappear jagged or flicker.

Focal planeOwing to the characteristics of the pickup elements(CMOS image sensors) for reading video signals,subjects that quickly move across the screen may appearslightly skewed.

FlickerIf recording is made under lighting produced bydischarge tubes, such as fluorescent, sodium, ormercury-vapor lamps, the screen may flicker, colorsmay vary, or horizontal stripes may appear distorted. Insuch cases, turn the FLICKER CANCEL function on(see page 26 ).In some cases, such phenomena may not be improvedwith the FLICKER CANCEL function.It is recommend to set the shutter speed to 1/100 sec. inthe areas of 50 Hz power supply frequency and to 1/60in the areas of 60 Hz.


7/73

Ov er v i ew

Features 7

Overview

Features

Compact, HD video camera with built-inpan/tilt/zoom functions• This HD video camera is equipped with an HD camera

block, pan/tilt mechanism, and 18-magnificationoptical/4-magnification digital zoom lens in acompact body. The compactness and integration allowthe camera versatile usage.

• The camera is provided with a wide-angle pan/tiltmechanism of ±175º horizontally, 90º upward and 30ºdownward, which enables wide-range remoteshooting.

• The pan/tilt mechanism is designed to be quiet so as to

minimize troublesome noise.• The supplied ceiling brackets allow installation of the

camera on a ceiling or a shelf, etc. in a high position.

HD CMOS camera with high image qualityand high-resolution remote shooting• The newly developed camera system that incorporates

1/3-type CMOS image sensors with a total of2,250,000 picture elements allows shooting of high-definition images, providing superior picture qualitywith high sensitivity and lower smear level.

• Shooting an image using the 1080i (effectiveinterlaced scanning: 1080 lines) high-definitionformat, which is equivalent to the HDTV broadcast, isenabled. The HD format can be switched (1080/59.94ior 1080/50i) with the switch at the bottom of thecamera.

• A volume of information of four times the capacity ofa normal TV broadcast and camera image shot in 16:9aspect ratio provides a theater-like wide screenpicture.

Multi-format HD outputsThe camera supports output in 720P format (progressivescanning format with 720 effective scan lines) as well asin 1080i format. These formats can be selected with aswitch at the bottom of the camera, which also allowsswitching between the 720/59.94P and 720/50P formats.

Built-in down-converted outputThe camera is equipped with video output connectors,allowing HD 1) or SD 2) output without inserting anInterface Board. You can use the connectors for SDoutput at the moment and use them for HD output in thefuture.

An analog component signal output connector for HDoutput, a composite signal output connector, and an Svideo signal output connector for SD output standardequipment.1) “HD” indicates high-definition broadcast with 1,080

effective scanning lines.2) “SD” indicates standard-definition broadcast

(conventional television).

Built-in interface card slotThe camera is equipped with an interface card slot forthe optional BRBK-HD2 HD-SDI Output Card. Use ofthe BRBK-HD2 HD-SDI Output Card provides supportfor additional image output formats.

VISCA camera protocol supported• The camera is equipped with both RS-232C and RS-

422 communication interfaces. As the camerasupports the industry-standard VISCA cameraprotocol, up to 7 cameras can be connected andremotely controlled at a high communication speed of38,400 bps.

• The optional RM-BR300 Remote Control Unit allowseasy camera operations.

External video sync functionThe camera is equipped with an external video syncfunction to synchronize the camera images on multiplecameras.

Tally lampThe tally lamp of the camera allows you to make sure itis selected at a glance.

COLOR AE functionThe COLOR AE function enables automatic exposureadjustment for a specific color.

Built-in ND filterThe ND (Neutral Density) filter allows control ofamount of light. The ND filter can be set to 1/4 or 1/16,using the menu or Remote Commander.


8/73

Ov er v i ew

System Components8

System ComponentsIn order to support multiple system configurations, avariety of optional products are available for the BRC-Z330 HD Color Video Camera. This section introducesthese optional products as well as the accessoriessupplied with the camera.

Supplied Components andAccessoriesBefore using the camera, make sure you have thefollowing components and accessories supplied.

Camera (1)

MPA-AC1 AC power adaptor (Sony) (1)

AC power cord (1)USA and Canadian model

European model

Remote commander (1)

Ceiling bracket (A) (1)

Ceiling bracket (B) (1)

Wire rope (1)

Two R6 (size AA) batteriesare not supplied.


9/73

Ov er v i ew

System Components 9

Screw 3 M3 × 8 (7)/Stainless screw 3 M4 × 8 (1)

RS-422 Connector plug (1)

Operating Instructions (1)

Optional Products

RM-BR300 Remote Control Unit

The joystick of the Remote Control Unit allows youcomfortable pan/tilt and zoom operations. The RemoteControl Unit also allows remote operation of up to sevencameras.Supplied accessories: AC power adaptor (1), AC powercord (1), RS-232C connecting cable (3 m) (1), RS-422connector plug (2)

BRBK-HD2 HD-SDI Output Card

Insert the card into the camera to allow output of an HD-SDI signal conforming to SMPTE292M serial digitalinterface standardss. No audio signal is output from thecard.

Video Switcher (commercially available)

It switches the video signal input of multiple cameras.

BRS-200 Remote Camera Operating Switcher

This switcher can be used as a camera control, allowingcamera operation such as pan/tilt and zoom operations.The switcher also allows switching of video signalsinput from multiple cameras.Supplied accessories: AC power cord (1), AC poweradaptor (1), AC power cord for AC power adaptor (1),Control cable (for connection between the ProcessorUnit and Control Panel) (1), Rack mounting bracket (1set), RS-422 connector plug (1), Power cord stopper (1),DC IN connector retainer (1)

For details, consult with your Sony dealer.


10/73

Ov er v i ew

System Configuration10

System ConfigurationThe BRC-Z330 HD Color Video Camera has various system configuration capabilities using optional products. Thissection describes system examples with the required components and the main usage of each system.

Operating a BRC-Z330 Camera Using the Supplied Remote Commander

This system allows you:To operate the camera readily from a short distance

System configuration

Operating a BRC-Z330 Camera Using the RM-BR300 Remote Control Unit

This system allows you:To perform pan/tilt and zoom operations using the joystick of the Remote Control Unit


BRC-Z330

Video signal

Signal flowRemote Commander(supplied)

HD video monitor, VTR, etc.

,


BRC-Z330


Video signalRemote Control (VISCA) signal

Signal flow


11/73

Ov er v i ew

System Configuration 11

Operating Multiple BRC-Z330 Cameras Using the RM-BR300 RemoteControl Unit

This system allows you:• To operate up to seven cameras remotely using a single Remote Control Unit• To perform pan/tilt and zoom operations using the joystick


,

Video signalRemote control (VISCA) signalTally/contact signal

Signal flow

BRC-Z330

BRC-Z330

BRC-Z330


Video switcher



12/73

Ov er v i ew

System Configuration12

Operating Multiple BRC-Z330 Cameras Using the BRS-200 Remote CameraOperating Switcher

This system allows you:• Operate up to seven cameras remotely and perform switching, using a single Remote Camera Operating Switcher• To perform pan/tilt and zoom operations using the joystick


NoteTo operate a BRC-Z330 with the BRS-200 Remote Camera Operating Switcher, install an optional BRBK-HD2 HD-SDI Output Card in the BRC-Z330, which cannot be controlled this way without a BRBK-HD2 HD-SDI Output Cardinstalled.

,

BRS-200REMOTE CAMERA OPERATING SWITCHER

BRBK-HD2

BRS-200 Control Panel


BRS-200 Processor

Video signalRemote control (VISCA) signal

Signal flow

BRC-Z330

BRC-Z330

BRC-Z330

BRBK-HD2

BRBK-HD2

Control cable(supplied with theBRS-200)


13/73

Ov er v i ew

Location and Function of Parts 13

Location and Functionof Parts

Camera

Front

A LensThis is a 18-magnification optical zoom lens.

B Tally lampLights in red when a VISCA tally command isreceived or the camera is selected by the RM-BR300 Remote Control Unit (not supplied).Flashes at intervals of about 0.5 seconds if therotating speed of the cooling fan motor is loweredor the motor has stopped regardless of on/off of thetally lamp.

C Remote sensorThis is the sensor for the supplied RemoteCommander.When you use the upper remote sensor, set IMG-FLIP to ON in the SYSTEM menu (page 28) . Withthis setting the remote sensor at the rear of thecamera does not function.

D SONY and HD nameplatesPull them out to turn them over and attach upsidedown if necessary.

E POWER lampLights when the camera is connected to an ACoutlet using the supplied AC power adaptor and ACpower cord.Flashes in green when the camera receives anoperation command from the supplied RemoteCommander.

F STANDBY lampLights when the camera is turned off using theRemote Commander.

Rear

G DC IN 12V connectorConnect the supplied AC power adaptor.

H VISCA RS-422 connectorUsed for VISCA control.

For connection to the VISCA RS-422 connector,see “Using the VISCA RS-422 Connector Plug” onpage 73 .

I IR SELECT switchSelect the camera number when you operatemultiple cameras with the same RemoteCommander (page 33) .

J Remote sensorThis is the sensor for the supplied RemoteCommander.

This remote sensor does not function when IMG-FLIP is set to ON in the SYSTEM menu (page 28) .

K DATA MIX switchSet the switch to ON to overlap the menu with thevideo signal output from the installed Output Card.Set it to OFF not to overlap the menu.

L 75-ohm termination switchThis switch is used when an external sync signal isused. Set it to OFF when this camera is in themiddle of a daisy chain connection of multiple

cameras. Set it to ON when the camera is at the endof a daisy chain connection or when nothing isconnected to the EXT SYNC IN connector on thecamera.

M EXT SYNC IN connectorAccepts external video sync signals.

N VISCA RS-232C IN connectorConnect to the RM-BR300 Remote Control Unit(not supplied). When you connect multiplecameras, connect it to the VISCA RS-232C OUT

1

5 6

32

4

RGB/COMPONENT

VISCARS-422

1 2 3 4 5 6 7 8 9

EXT SYNC IN

VIDEO

IRSELECT

75

123

OFF ON

DATAMIXOFF ON

I N V I SC A R S -2 3 2C O U T S VIDEO

!

DCIN12V

R

qfqgqhqj

7 890qaqsqd

qk ql


14/73

Ov er v i ew

Location and Function of Parts14

connector of the previous camera in the daisy chainconnection.

O VISCA RS-232C OUT connectorWhen you connect multiple cameras, connect it tothe VISCA RS-232C IN connector of the nextcamera in the daisy chain connection.

P S VIDEO connectorOutputs the camera images as S video signal.

Q T VIDEO connectorOutputs the camera images as composite videosignal.

R Card slotInsert the optional BRBK-HD2 Output Card.The slot cover is attached to the camera at thefactory.

S RGB/COMPONENT connectorSupplies the images as analog component (YPbPror RGB) signal.

Bottom

T Ceiling bracket mounting screw holesWhen you install the camera to the ceiling or on ashelf, etc. in a high position, secure the suppliedceiling bracket to these holes using the suppliedfour screws. The four feet are attached to the holesat the factory.

For installation, see “Installing the Camera in aHigh Position” on page 44 .

U Tripod screw holes (1/4-20UNC)When you install the camera to a tripod, secure thetripod to these holes.

V BOTTOM switchesUsed for the output signal format selection, RS-232C/RS-422 selection, baud rate selection, remotecontrol signal output on/off and camera addresssetting.

For details, see “Setting of the BOTTOM switches”on page 14 .

Setting of the BOTTOM switches

1 Switch 1 (59.94/50 signal format selector)Set to ON for output in 1080/50i (720/50P) signalformat, OFF for output in 1080/59.94i (720/ 59.94P) signal format.

2 Switch 2 (1080i/720p signal format selector)Set to ON for output in 720p signal format, OFF foroutput in 1080i signal format.

3 Switch 3 (RS-232C/RS-422 selector)Set to ON for RS-422, or OFF for RS-232C.

4 Switch 4 (Communication baud rate selector)

Set to ON for 38400 bps, or OFF for 9600 bps.

5 Switches 5-7 (Camera address selector)Set the address of the camera.Normally set to “0”. With this setting, addresses areassigned to the cameras automatically in theconnected order by pressing the POWER buttonwhile holding down the RESET button on the RM-BR300 Remote Control Unit.You can assign the camera address “1” to “7”manually by setting these selectors as follows:

6 Switch 8 (Infrared signal output switch)Set to ON to enable an infrared signal output, orOFF to disable the output.

7 Switches 9, 10These switches are not used.

waw; ws

Cameraaddress

0 1 2 3 4 5 6 7

Switch 5 OFF ON OFF ON OFF ON OFF ON

Switch 6 OFF OFF ON ON OFF OFF ON ON

Switch 7 OFF OFF OFF OFF ON ON ON ON

ON

1234

56789

101B

21

45

7

3

6


15/73


16/73

Ov er v i ew


Installing batteries

CAUTION

Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent typerecommended by the manufacturer.When you dispose of the battery, you must obey the lawin the relative area or country.

Note

To avoid risk of explosion, use R6 (size AA) manganeseor alkaline batteries.

RM-BR300 Remote Control Unit(not supplied)This manual explains the operations of the RM-BR300Remote Control Unit when it is used with BRC-Z330cameras.For operations with other cameras, refer to theOperating Instructions supplied with the RM-BR300.

Front

A LOCK button and indicatorPress the LOCK button for more than one second,and the LOCK indicator lights and the values set bythe VALUE/R, BRIGHT/B and FOCUS controlsare locked. (The indicators of the locked controls

are turned off.) The AUTO/MANUAL button isalso disabled.Press the LOCK button for more than one secondagain to unlock the controls and buttons.

B VALUE/R controlWhen the brightness adjustment mode isselected with the MODE button (with theVALUE indicator lit):Adjusts the value of the item (SHUTTER, IRIS orGAIN) selected with the menu of the camera.When the VALUE indicator is lit, the function ofthe control varies according to the MODE setting inthe EXPOSURE menu of the camera. For details,see “Functions of the VALUE and BRIGHTcontrols” on page 41 .

When the white balance adjustment mode isselected with the MODE button (with the Rindicator lit):The function of the control with the R indicator lit

varies according to the white balance mode selectedon the camera. For details, see “Functions of the Rand B controls” on page 40 .

C BRIGHT/B controlWhen the brightness adjustment mode isselected with the MODE button (with theBRIGHT indicator lit):Adjusts the value of the brightness of the camera,etc.When the BRIGHT indicator is lit, the function ofthe control varies according to the MODE setting in

the EXPOSURE menu of the camera. For details,see “Functions of the VALUE and BRIGHTcontrols” on page 41 .

When the white balance adjustment mode isselected with the MODE button (with the Bindicator lit):The function of the control with the B indicator litvaries according to the white balance mode selectedon the camera. For details, see “Functions of the Rand B controls” on page 40 .

D MODE buttonPress this button to select the function of theVALUE/R control and BRIGHT/B control.When the brightness adjustment mode is selected,the VALUE and BRIGHT indicators are lit.When the white balance adjustment mode isselected, the R and B indicators are lit.

E FOCUS controlTurn this control counterclockwise (toward NEAR)to focus on a near subject, and clockwise (towardFAR) to focus on a far subject.

Two R6 (size AA)batteries (not supplied)

1

19

LOCK

MODE

VALUE

RESET

MENU

PRESET

SHIFT

L/RDIRECTION

PANELLIGHT

BLACKLIGHT

PAN-TILTRESET

ONE PUSHAWB

POWERAUTO

MANUAL

AUTO

ONEPUSHAF

2 3 4 5 6 7

210S TD R EV

311 4

POSITION

CAMERA

12 513 614 715 816

R

– +

BRIGHT

B

– +

FOCUS

N EA R F AR

18

qhqjqk ql w;

90qaqsqd qf qg

2

34567


17/73

Ov er v i ew


F AUTO/MANUAL button and AUTO indicatorPress this button to select focus mode, AUTO orMANUAL.When AUTO is selected, the AUTO indicator lightsand the FOCUS control and the ONE PUSH AFbutton are disabled.If you set AF ASSIST to ON in the FOCUS menu,you can focus on another object with the FOCUScontrol.When MANUAL is selected, the FOCUS controland the ONE PUSH AF button are enabled (withthe FOCUS indicator lit).

G ONE PUSH AF buttonPress this button to perform the one-push auto focusfunction.

H RESET buttonHold down this button and press one of thePOSITION buttons, and the memory of the cameracorresponding to the pressed POSITION button iscleared to the factory-preset conditions.When multiple cameras are connected, hold downthis button and press the POWER button to set thecamera addresses automatically.

I PRESET buttonHold down this button and press one of thePOSITION buttons, and the current camera settingsare stored in the memory of the cameracorresponding to the pressed POSITION button.

J PANEL LIGHT button

Press this button to illuminate all the POSITIONbuttons and CAMERA buttons. Press the buttonagain to turn off the illumination.

K BACK LIGHT buttonWhen FULL AUTO, SHUTTER Pri, IRIS Pri orGAIN Pri is selected with MODE of theEXPOSURE menu, press this button to enable thebacklight compensation function of the camera.Press it again to disable the function.Hold down the SHIFT button and press this buttonto enable the spotlight compensation function of thecamera. This function adjusts the exposure to adarker level if a portion of the shooting object isilluminated.To disable the spotlight compensation, hold downthe SHIFT button and press this button again.

L PAN-TILT RESET buttonPress this button to reset the pan/tilt position of thecamera to the initial conditions.

M ONE PUSH AWB button

When ONE PUSH is selected with the WHITEBALANCE menu of the camera, press this buttonto perform the one-push white balance adjustment.

N MENU buttonPress this button for about one second to display orturn off the menu of the camera, or return to themain menu.

O Joystick

When the menu of the camera is notdisplayedThe joystick is used for pan/tilt and zoomoperations.When you incline the joystick right and left, thecamera pans. When you incline it forward orbackward, the camera tilts. The pan/tilt speedchanges according to the angle of the inclination.When you release the joystick, the cameramovement stops.

When you turn the dial on the upper part of the joystick clockwise, the subject becomes larger(zoom in). When you turn it counterclockwise, thesubject becomes smaller (zoom out).When you press the button on the top of the joystickfor one or two seconds regardless of the PAN TILTZOOM menu setting, the pan/tilt/zoom are resetand the camera returns to the front.

When the menu of the camera is displayedThe joystick is used for menu operations.Inclining the joystick right, left, forward andbackward has the same function as pressing thearrow buttons of the supplied Remote Commander.Pressing the button on the top of the joystick has thesame function as pressing the HOME button on theRemote Commander.

P SHIFT button and indicatorsHold down this button and press one of thePOSITION buttons. The lower indicator lights andyou can use the POSITION buttons for positions 9to 16. If you release the SHIFT button, the upperindicator lights and the POSITION buttons can beused for positions 1 to 8.

Q L/R DIRECTION buttonHold down this button and press POSITION button2 (REV) to reverse the pan direction to the directionin which you incline the joystick. To reset thedirection, hold down this button and pressPOSITION button 1 (STD).

R POWER buttonPress this button to light the CAMERA button(s)corresponding to the status of the connectedcamera(s).


18/73

Ov er v i ew


Blue: The power of the camera is on.Yellow green: The camera is in standby mode.Off: No camera is connected.Hold down this button and press CAMERA button1 to 7 to turn on/off the power of the cameracorresponding to the pressed button.

S CAMERA buttonsPress one of the buttons to select the camera fromamong those connected. The selected CAMERAbutton lights in blue.

T POSITION buttonsYou can store the various camera settings such asthe pan, tilt and zoom positions to the memory ofthe camera corresponding to each POSITIONbutton, and load the settings in the memory.

Rear/Bottom

U MODE selectorSelect the position corresponding to the VISCA-

controllable camera to be connected.

Note

Set the selector to position 8 when all the connectedcameras are BRC-Z330s. For other connections, setthe selector to position 0.

V VISCA RS-232C connectorConnect to the VISCA RS-232C IN connector ofthe camera.

W VISCA RS-422 connectorConnect to the VISCA RS-422 connector of thecamera.An RS-422 connector plug is attached at thefactory.

X TALLY/CONTACT connectorThis connector is used for the tally lamp input or thecontact output.Select the function of the connector using theTALLY/CONTACT selector.An RS-422 connector plug is attached at thefactory.

Y TALLY/CONTACT selectorSelect the function of the TALLY/CONTACTconnector.TALLY: The tally lamp of the camera selectedwith the connected switcher lights.CONTACT: The contact output corresponding tothe camera address selected with the RemoteControl Unit is short-circuited against theconnected switcher.CONTACT (TALLY): The contact outputcorresponding to the camera address selected withthe Remote Control Unit is short-circuited againstthe connected switcher and the tally lamp of thecamera selected with the Remote Control Unitlights.

Notes

• Change the setting of the selector before you turnon the power for the Remote Control Unit.

Otherwise, the setting is not effective.• For more details on the functions of the TALLY/ CONTACT selector, refer to the OperatingInstructions of the RM-BR300.

wh DC IN 12V connectorConnect the supplied AC power adaptor.

wj DIP switches (bottom)Switch 1 (RS-232C/RS-422 selector)Set to ON for RS-422, or OFF for RS-232C.

Switch 2 (Communication baud rate selector)Set to ON for 38400bps, or OFF for 9600bps.

Switch 3 (BRIGHT control function selector)Set to ON for IRIS and GAIN adjustments, or OFFfor IRIS adjustment only.

Note

Set the DIP switches before you turn on the powerof the Remote Control Unit. Otherwise, the settingis not effective.

Switch position Camera mode

0 Automatically selected (default)

1 BRC-300/300P

2 EVI-D70/D70P

3 EVI-D100/D100P

4 EVI-D30/D30P

5 SNC-RZ30N

6 BRC-H700

7 BRC-Z700

8 BRC-Z330

MODEVISCA

1 9 1 9

RS-422 ON/OFFTALLY/CONTACTRS-232C CONTACT(TALLY)!TALLY

C O NTA CT D C I N 1 2 V

ws wd wf wgwh wj wkwa


19/73

Ov er v i ew


wk ON/OFF switchPress this switch to turn on/off the Remote ControlUnit.

BRBK-HD2 HD-SDI Output Card(not supplied)

A SDI OUTPUT connectors (BNC type)The Card allows output of an HD-SDI signalconforming to SMPTE292M serial digital interfacestandards. No audio signal is output from the card.

SDI OUTPUT

BRBK-HD2

1


20/73

A d j us t i ngand S et t i ngWi t h Menus

About On-Screen Menus20

Adjusting and Setting With Menus

About On-Screen MenusYou can change various settings, such as shootingconditions and system setup of the camera, whileobserving menus displayed on a connected monitor.This section explains how to read the on-screen menusbefore starting menu operations.

For the overall menu configurations, see page 60 .

Note

You cannot perform pan/tilt and zoom operations whilethe menu is displayed.

Main MenuTo display the main menu, press the DATA SCREENbutton on the supplied Remote Commander or theMENU button on the RM-BR300 Remote Control Unit.

1 CursorSelects a setting menu.Move the cursor up or down by pressing the V or v button on the Remote Commander or by incliningthe joystick of the RM-BR300 Remote ControlUnit forward or backward.

2 Menu itemsTo display a setting menu, select one using the V orv button on the Remote Commander or the joystickof the RM-BR300 Remote Control Unit, and pressthe HOME button on the Remote Commander orthe top button of the joystick on the RM-BR300.

3 Option Card indicatorDisplays the name of the output card inserted intothe card slot of the camera.(The illustration above shows an example when theBRBK-HD2 HD-SDI Output Card is inserted.)

Setting MenusThe setting menu selected on the main menu isdisplayed.

1 Setting menuThe name of the setting menu currently selected isdisplayed here.

2 CursorSelects a setting item.Move the cursor up or down by pressing the V or v button on the Remote Commander or inclining the

joystick of the RM-BR300 Remote Control Unitforward or backward.

3 Setting itemsThe setting items for this setting menu aredisplayed.To change a set value, select the setting item using

theV

orv

button on the Remote Commander or the joystick of the RM-BR300 Remote Control Unit,and press the B or b button on the RemoteCommander or incline the joystick on the RM-BR300 right or left.

4 Set valueThe currently set values are displayed.To change a set value, use the B or b button on theRemote Commander or the joystick of the RM-BR300 Remote Control Unit.

For the default value of each setting item, see“Menu Configuration” on page 60 .

< M E N U > H D - S D I > E X P O S U R E C O L O R P I C T U R E F O C U S PAN TILT ZOOM SYSTEM

VIDEO OUT STATUS

< S Y S T E M > > I R - R E C E I V E I M G - F L I P PA N R E V E R S E T I LT R E V E R S E D I S P L AY I N F O S Y N C M A S T E R H PHASE

ON

O FFO FFO FF

ONHD10


21/73

A d j u s t i n g an d S e t t i n gWi t h M

en u s

Operation Through Menus 21

Operation ThroughMenusThis section explains how to operate the menu using thesupplied Remote Commander, or using the RM-BR300Remote Control Unit (not supplied).

For details on each menu, see pages 23 through 30.

Menu Operation Using the SuppliedRemote Commander

1 Press the DATA SCREEN button.The main menu appears.

2 Move the cursor to the setting menu item to be setby pressing the V or v button.

3 Press the HOME button.The selected setting menu appears.

4 Move the cursor to the setting item to be changed bypressing the V or v button.

5 Change the value by pressing the B or b button.

Note

When you are operating the menu using the suppliedRemote Commander, you cannot set IR-RECEIVE inthe SYSTEM menu to OFF. To set IR-RECEIVE to

OFF, use the RM-BR300 Remote Control Unit or theVISCA command.

To return to the main menuPress the DATA SCREEN button.

To return to the normal displayWhen the main menu is displayed, press the DATASCREEN button once. If a lower-level menu isdisplayed, press it twice.

P O W E

R

C A M E

R A S E

L E C T

1

2

3

A U T O

P O S I T

I O N

H O M E

R M - E V

1 0 0

P R E S

E T

S T D

R E V

B A C K

L I G H T

M A N U

A L

F A R

F O C U

S N E

A R

W T

W T

3

4 5

6

P A N - T

I L T

S L O W

F A S T

Z O O M

L / R

D I R E C

T I O N

S E T

P A N - T

I L T

R E S E

T

D A T A S

C R E E

N

R E S E

T 2 11

2,45

3

< M E N U > H D - S D I > E X P O S U R E C O L O R P I C T U R E F O C U S PA N T I LT Z O O M S Y S T E M V I D E O O U T S TAT U S

< S Y S T E M > > I R - R E C E I V E I M G - F L I P PA N R E V E R S E T I LT R E V E R S E D I S P L AY I N F O S Y N C M A S T E R H P H A S E

ON

O FFO FFO FF

ONHD10

< S Y S T E M > I R - R E C E I V E I M G - F L I P PA N R E V E R S E T I LT R E V E R S E > D I S P L AY I N F O S Y N C M A S T E R H P H A S E

ON

O FFO FFO FFO FF

HD10


22/73


Operation Through Menus22

Menu Operation Using the RM-BR300 Remote Control Unit

1 Press the MENU button for about one second.The main menu appears.

2 Move the cursor to the setting menu item to be setby inclining the joystick forward or backward.

3 Press the button on the top of the joystick.

The selected setting menu appears.

4 Move the cursor to the setting item to be changed byinclining the joystick forward or backward.

5 Change the value by inclining the joystick right orleft.

To return to the main menuPress the MENU button for about one second.

To return to the normal displayWhen the main menu is displayed, press the MENUbutton once. If a lower-level menu is displayed, press ittwice.When pressing the MENU button, hold it pressed forabout one second.

1

19

LOCK

MODE

VALUE

RESET

MENU

PRESET

SHIFT

L/RDIRECTION

PANELLIGHT

BLACKLIGHT

PAN-TILTRESET

ONEPUSHAWB

POWERAUTO

MANUAL

AUTO

ONEPUSHAF

2 3 4 5 6 7

210

S TD R EV

311

4

POSITION

CAMERA

12513

614

715

816

R– +

BRIGHT

B– +

FOCUS

N E AR F A R

1 2,4,5

3

< M E N U > H D - S D I > E X P O S U R E C O L O R P I C T U R E F O C U S PA N T I LT Z O O M S Y S T E M V I D E O O U T S TAT U S

< S Y S T E M > > I R - R E C E I V E I M G - F L I P PA N R E V E R S E T I LT R E V E R S E D I S P L AY I N F O S Y N C M A S T E R H PHASE

ON

O FFO FFO FF

ONHD10

< S Y S T E M > I R - R E C E I V E I M G - F L I P PA N R E V E R S E T I LT R E V E R S E > D I S P L AY I N F O S Y N C M A S T E R H P H A S E

O N

OF FOF FOF FOF F

H D1 0


23/73


en u s

EXPOSURE Menu 23

EXPOSURE MenuThe EXPOSURE menu is used to set the items regardingthe exposure.

MODE (exposure mode)FULL AUTO: The exposure is adjusted automatically

using the sensitivity, electronic shutter speed andiris.

MANUAL: The sensitivity (GAIN), electronic shutterspeed (SPEED) and iris (IRIS) are adjustedmanually.

SHUTTER Pri: Shutter Priority mode. The exposure isadjusted automatically using the sensitivity and iris.Adjust the electronic shutter speed (SPEED)manually.

IRIS Pri: Iris Priority mode. The exposure is adjustedautomatically using the sensitivity and electronicshutter speed. Adjust the iris (IRIS) manually.

GAIN Pri: Sensitivity Priority mode. The exposure isadjusted automatically using the iris and electronic

shutter speed. Adjust the sensitivity (GAIN)manually.

When you select MODE, some of the following settingitems that are required for the selected mode appear.

AE SPEED: Select the exposure adjustment speed atwhich an optimum exposure value is obtainedautomatically. You can select LOW (slow speed),MID (normal speed) or HIGH (fast speed). Selectwhen the brightness of the object is changedmomentarily.

AGC LIMIT: Select the maximum gain level to beadjusted in automatic exposure mode. Select avalue from among –3, 0, 6 and 12 dB. If you set theitem to OFF, the gain is adjusted without limitation.

IRIS LIMIT: Select the maximum iris to be adjusted inautomatic exposure mode. Select a value fromamong F11, F6.8, F4.0 and F3.4.

GAIN: Select the gain from among –3 dB, 0 to 24 dB bythe unit of 1 dB and HYPER

SPEED: Select the electric shutter speed from amongthe following:

For the 1080/59.94i or 720/59.94P signalformat1/10000, 1/6000, 1/4000, 1/3000, 1/2000, 1/1500,1/1000, 1/725, 1/500, 1/350, 1/250, 1/180, 1/125,1/100, 1/90, 1/60

For the 1080/50i or 720/50P signal format1/10000, 1/6000, 1/3500, 1/2500, 1/1750, 1/1250,1/1000, 1/600, 1/425, 1/300, 1/215, 1/150, 1/120,1/100, 1/75, 1/50

IRIS: Select the iris from among the following:CLOSE, F16, F15, F14, F12, F11, F10, F9.6, F8.7,F8.0, F7.3, F6.8, F6.2, F5.6, F5.2, F4.8, F4.4, F4.0,F3.7, F3.4, F3.1, F2.8, F2.6, F2.4, F2.2, F2.0, F1.8,F1.7, F1.6

EX-COMP (exposure compensation)When MODE is set this item to FULL AUTO,SHUTTER Pri, IRIS Pri or GAIN Pri, set this item toON to enable exposure compensation.When you set EX-COMP to ON, LEVEL appears andyou can select the exposure compensation level fromamong the following:–7, –6, –5, –4, –3, –2, –1, 0, +1, +2, +3, +4, +5, +6, +7If you set the level to 0, exposure compensation will bedisabled. Level +7 is the brightest and –7 is the darkestcompensation values.When EX-COMP is set to OFF, exposure compensationdoes not function.

BACK LIGHT

Setting the item to ON enables the BACK LIGHTfunction. Setting it to OFF disables the function.The BACK LIGHT feature is available only whenMODE (exposure mode) is set to any item other thanMANUAL.

SPOT LIGHTThe SPOT LIGHT function allows exposure adjustmentat darker levels if a portion of the object to be shot isilluminated.Setting the item to ON enables the SPOT LIGHTfunction. Setting it to OFF disables the function.

The SPOT LIGHT feature is available only whenMODE (exposure mode) is set to any other thanMANUAL.

Note

You cannot use both the BACK LIGHT and SPOTLIGHT functions at the same time.

COLOR AEThe exposure is adjusted automatically for specificcolor.

> M O D E A E S P E E D A G C L I M I T I R I S L I M I T E X - C O M P

B A C K L I G H T S P O T L I G H T COLOR AE

N D F I LT E R

F U L L A U TO MI D

12 dB F1 1

OF F

OF F OF F

OF F

OF F


24/73


COLOR Menu24

The COLOR AE feature is available only when MODE(exposure mode) is set to any item other thanMANUAL.

OFF: COLOR AE does not function.CHECK: The region of the color specified with PHASE

is displayed in white. The region is set to STD whenCHECK is selected.

WIDE: The region of the color specified with PHASEbecomes wide.

STD: The region of the color specified with PHASE isthat between NARROW and WIDE.

NARROW: The region of the color specified withPHASE becomes narrow.

When an item other than OFF is selected, PHASE isdisplayed, and you can specify the color for which theexposure is automatically adjusted. The adjustable rangeis from 0 to 71.

To set the COLOR AE

1 Set COLOR AE to CHECK.

2 Select PHASE to adjust so that the color region inwhich the exposure is automatically adjusted isdisplayed in white.

3 Set COLOR AE to NARROW, STD, or WIDE.

Note

You cannot store the status when CHECK is selected inthe preset memory of the camera.

ND FILTERSelect the filtering level of the camera’s built-in NDFILTER.Select from among OFF, 1/4, and 1/16.

OFF: ND FILTER does not function.1/4: Decrease the amount of light by 1/4.1/16: Decrease the amount of light by 1/16.

Note

If you switch the ND FILTER during shooting, cameraimage may be distorted.

COLOR MenuThe COLOR menu is used to adjust the white balanceand the color.

WHITE BALANCE (white balance mode)Select the white balance mode from among thefollowing:AUTO1, AUTO2, INDOOR, OUTDOOR, ONE PUSH,MANUAL

AUTO1: Adjusts the white balance automatically whileleaving natural colors.

AUTO2: Adjusts the white balance automatically.INDOOR: The R.GAIN and B.GAIN values are fixed

to those for a color temperature of 3200K.OUTDOOR: The R.GAIN and B.GAIN values are

fixed to those for a color temperature of 5800K.ONE PUSH: The white balance adjustment is activated

when you zoom in on a white object in the center ofthe screen and press the HOME button on the

supplied Remote Commander, or press the buttonon the top of the joystick or the ONE PUSH AWBbutton on the RM-BR300 Remote Control Unit.

MANUAL: Adjusts the white balance manually.

When you select any mode of WHITE BALANCE,some of the following setting items that are required forthe selected mode appear.

WB SENS: You can adjust the speed with which thecolor of an object is put close to white balancefocusing point in AUTO1 or AUTO2 mode. Set toHIGH to do so at higher speed and to LOW to do so

at lower speed.You can also adjust the red or blue tint whenshooting an object under reddish light sources suchas an incandescent light and candle, or under bluishlight sources such as the shade. Selecting HIGHdecreases red or blue tint, and selecting LOWincreases red or blue tint.

WB R.SHIFT, WB B.SHIFT: You can shift the whitebalance focusing point in automatic white balancemode to your favorite red tint (WB R.SHIFT) orblue tint (WB B.SHIFT) individually. Theadjustable range of each item is from –7 to +7.

>WHITE BALANCE WB SENS

WB R .SHIFT WB B .SHIFT COLOR GAIN COLOR HUE COLOR MATRIX R .ENHANCE G.ENHANCE B .ENHANCE YL.ENHANCE CY.ENHANCE MG.ENHANCE

AUTO1

M ID

0000

ON000000


25/73


en u s

PICTURE Menu 25

R.GAIN, B.GAIN: When you select MANUAL,R.GAIN (red gain) and B.GAIN (blue gain) appear.You can adjust the white balance manually withinthe range between –128 and +127.

COLOR GAINFor adjusting the color intensity of the picture. Theadjustable range is from –7 to +7. The color intensity

increases in the + direction, and decreases in the –direction.

COLOR HUEFor adjusting the color hue of the picture. The adjustablerange is from –7 to +7.

Note

When COLOR MATRIX is set to OFF, COLOR HUEcannot be set.

COLOR MATRIXEnhances or reduces a specific color region withoutchanging the white balance focusing point.

ON: You can adjust the R.ENHANCE (red),G.ENHANCE (green), B.ENHANCE (blue),YL.ENHANCE (yellow), CY.ENHANCE (cyan),and MG.ENHANCE (magenta) color regions witheach item within the range of –10 to +10.

OFF: COLOR MATRIX does not function.

PICTURE MenuThe PICTURE menu is used to adjust the picture quality.

DETAILSelect the image enhancer level.The adjustable level is in the range of 0 to 15. The largerthe setting level, the sharper the image outline. You canobtain the softest image outline by selecting level 0.

COLOR DETAILReduces the image enhancer of a specific color.

OFF: COLOR DETAIL does not function.CHECK: The region of the color specified with PHASE

is displayed in white. The region is set to STD whenCHECK is selected.

NARROW: The region of the color specified withPHASE becomes narrow.

STD: The region of the color specified with PHASE isthat between NARROW and WIDE.

WIDE: The region of the color specified with PHASEbecomes wide.

When an item other than OFF is selected, PHASE isdisplayed and you can specify the color whose imageenhancer you want to reduce. The adjustable range isfrom 0 to 71.

To set the COLOR DETAIL

1 Set COLOR DETAIL to CHECK.

2Select PHASE to adjust so that the color region inwhich you want to reduce the image enhancer isdisplayed in white.

3 Set COLOR DETAIL to NARROW, STD orWIDE.

Note

You cannot store the status when CHECK is selected inthe preset memory of the camera.

< P I C T U R E > > D E TA I L C O L O R D E TA I L

G A M M A K N E E P O I N T F L I C K E R C A N C E L B &W C O L O R B A R

7

O FF

NORMALAUTO

O FFO FFO FF


26/73


FOCUS Menu26

GAMMASelect the gamma curve of the camera.

NORMAL: The object is shot using normal gammacurve.

CINEMA: The object is shot using a gamma curve toreproduce a film-like picture with a natural tone.

KNEE POINTThe KNEE function minimizes washout of picture thatmay occur with a bright portion of a picture or whenshooting a white object.

AUTO: The KNEE POINT is adjusted automatically.LOW: Set the KNEE POINT to lower level than MID.MID: Set the KNEE POINT midway between LOW and

HIGH.HIGH: Set the KNEE POINT to higher level than MID.OFF: KNEE does not function.

Note

When GAMMA is set to CINEMA, KNEE POINTcannot be set.

FLICKER CANCELWhen this item is set to ON, picture blurs (flicker) canbe reduced even when shooting under a 50Hzfluorescent light. Set it to OFF to disable this feature.

Note

The FLICKER CANCEL feature may have no effectdepending on the type of light source.

B&W (black and white mode)When this item is set to ON, an image is shot in blackand white.

COLOR BARWhen this item is set to ON, the built-in color bar of thecamera is displayed on the monitor screen.

FOCUS MenuThe FOCUS menu is used to select the focus mode.

MODE (focus mode)Select the focus adjustment mode.

AUTO: The focus is adjusted automatically.MANUAL: Adjust the focus manually. Use the FAR/

NEAR buttons on the supplied RemoteCommander to adjust the focus.

Note

Set MODE to MANUAL when you shoot• a flat subject with low contrast such as a white wall.• a subject through glass.• a lateral-striped subject.• a subject exposed to strong light with an illumination,

reflecting light, etc.• a subject in a dark background with flashing lights

such as a night view.

NEAR LIMITFocusing on a subject located near the camera is limited.

ON: A subject closer to the camera than about 50 cm(19 3 / 4 inches) is not focused.

OFF: The camera-subject distance is focused for about10 cm (4 inches) to infinity.

AF ASSIST (auto focus assist)You can temporarily adjust the focus manually evenwhen MODE is set to AUTO.The AF ASSIST feature is available only when MODEis set to AUTO.

ON: You can adjust to focus another subject in a forwardor backward location with the NEAR/FAR buttonson the supplied Remote Commander or the FOCUScontrol on the optional RM-BR300 Remote ControlUnit.

OFF: The focus of the subject is adjusted automatically.Manual focus adjustment is deactivated.

< F O C U S > > M O D E N E A R L I M I T A F A S S I S T

A U TO

O NO N


27/73


en u s

PAN TILT ZOOM Menu 27

PAN TILT ZOOM MenuThe PAN TILT ZOOM menu is used to select the pan/ tilt/zoom mode.

PAN-TILT LIMITWhen you set PAN to ON, you can select the limit of panoperation with the LEFT and RIGHT setting items.When you set TILT to ON, you can select the limit of tiltoperation with the UP and DOWN setting items.You can select the following values:

PAN LEFT: END, 174° to –174°, selectable with aninterval of 1°

PAN RIGHT: 174° to –174°, END, selectable with aninterval of 1°

TILT DOWN: END, –29° to 89°, selectable with aninterval of 1°

TILT UP: –29° to –89°, END, selectable with aninterval of 1°

Setting range of PAN LEFT/PAN RIGHT

Setting range of TILT DOWN/TILT UP

Notes

• Before storing the camera position in the presetmemory, perform the PAN-TILT LIMIT setting. If thecamera position is not within the range of the PAN-TILT LIMIT setting, you cannot store the cameraposition in the preset memory.

• The PAN-TILT LIMIT setting is reset to the factorysetting when you change IMG-FLIP of the SYSTEMmenu.

RAMP CURVESelect the speed acceleration or reduction mode whenthe preset operation is recalled.

MODE1: Speed accelerates or reduces most sharply.MODE2: Speed accelerates or reduces moderately.MODE3: Speed accelerates or reduces most gently.

D-ZOOM (digital zoom)When you select digital zoom magnification (4×, 2× or

1.5×), the selected electronic zoom operates after theoptical zoom (18×). You can zoom up to 72× atmaximum.When this item is set to OFF, the digital zoom functionis disabled.

Note

Regardless of the D-ZOOM setting, images shot withthe camera are accumulated for the verticalsynchronization period and output from the RGB/ COMPONENT connector, S VIDEO connector,

< PA N T I LT Z O O M > PA N - T I LT L I M I T

> PAN LEFT R I G H T T I LT DOWN UP R A M P C U RV E D - Z O O M

OF FEN DEN DOF FEN DEN D

M O D E 2OF F

174° –174°

CENTER (±0°)

END(–175°)

END(175°)

END (90°)

±0°

–29°

89°

END (–30°)


28/73


SYSTEM Menu28

VIDEO connector of the camera, and the SDIOUTPUT connector of an optional BRBK-HD2 OutputCard, if one is installed in a card slot. SYSTEM Menu

IR-RECEIVE (infrared signal reception)When it is set to OFF, the camera does not receive thesignal from the supplied Remote Commander.Be sure to keep it ON when you use the supplied RemoteCommander.

NoteYou cannot set IR-RECEIVE to OFF when you operatethe menu using the supplied Remote Commander. To setit to OFF, use the RM-BR300 Remote Control Unit (notsupplied) or the VISCA command.

IMG-FLIP (image flip)Set IMG-FLIP to ON to rotate the camera imagesupplied from the RGB/COMPONENT connector,

S VIDEO connector, VIDEO connector, andthe SDI OUTPUT connector on an optional BRBK-HD2

Output Card if one is installed in a card slot, upside/ down and to reverse the direction of the cameramovement with pan/tilt operations.

PAN REVERSE: Set to ON to reverse the horizontalmovement of the camera image.

TILT REVERSE: Set to ON to reverse the verticalmovement of the camera image.

When you set IMG-FLIP to ON, “Please restartsystem!” appears. Turn off the power of the camera andturn it on again.

Notes

• Regardless of the IMG-FLIP to ON/OFF setting,images shot with the camera are accumulated for thevertical synchronization period and output from the

RGB/COMPONENT connector, S VIDEOconnector, VIDEO connector of the camera, andthe SDI OUTPUT connector on an optional BRBK-HD2 Output Card, if one is installed in a card slot.

• When you set IMG-FLIP to ON, then turn off thecamera and turn it on again, PAN REVERSE andTILT REVERSE will be set to ON. When you set

< S Y S T E M > > I R - R E C E I V E I M G - F L I P PA N R E V E R S E T I LT R E V E R S E

D I S P L AY I N F O S Y N C M A S T E R H P H A S E

O N

OF FOF FOF F

O NH D1 0


29/73


en u s

VIDEO OUT Menu 29

IMG-FLIP to OFF, then turn the power off and onagain, PAN REVERSE and TILT REVERSE will beset to OFF.

• If you set IMG-FLIP to ON, the remote sensor at therear of the camera does not function.

DISPLAY INFO (information display)When the camera settings are stored in POSITION 1 to

16 using the supplied Remote Commander or the RM-BR300 Remote Control Unit, the message “PRESETNo. xx” automatically appears for 2 seconds on themonitor screen. If you want to display the message eachtime the camera is operated, set DISPLAY INFO to ON.Set it to OFF to cancel the display.

Note

The message will appear if the built-in cooling fan of thecamera has accidentally stopped. When DISPLAYINFO is set to OFF, the display of this message is alsocanceled.

SYNC MASTERWhen you connect a sync signal generator, you canselect an output video signal that is synchronized withthe external video sync signal input to the EXT SYNCIN connector on the camera from among the followingoutput signals:

HD: Selects the output signal from the RGB/ COMPONENT connector on the camera.

SD: Selects the output signal from the VIDEO orS VIDEO connector on the camera.

H PHASEWhen you connect a sync signal generator, adjust thehorizontal phase so that the output signal issynchronized with the external sync signal input to thecamera. The adjustable range is from 0 to 140.When you select H PHASE on the menu, the message“PUSH ENTER BUTTON” appears on the screen. Pressthe HOME button on the Remote Commander or thebutton on the top of the joystick on the Remote ControlUnit to make the color bars appear.After completing the adjustment, press the HOMEbutton on the Remote Commander or the button on thetop of the joystick on the Remote Control Unit to makethe color bar disappear.

VIDEO OUT Menu

HD-RGB/COMPONENT

FORMATSelect the signal output from the RGB/ COMPONENT connector on the camera.

YP BP R : Outputs analog component signals.RGB: Outputs RGB signals.

When you select a mode for FORMAT, some of thefollowing setting items that are required for selectedmode appear.

ADD SYNC: Specifies whether to add a sync signal.Setting the item to RGB specifies output of each R,G, and B signal with a sync signal added. Settingthe item to OFF specifies output of each R, G, andB signal with no sync signal added.

SYNC TYPE: Specifies the type of sync signal. Settingthe item to SYNC specifies output of tri-levelsync. Setting the item to VD specifies output of bi-level sync.

SD-VIDEO/S VIDEO

IMG SIZESelect the aspect ratio of the signal output from theVIDEO or S VIDEO connector on the camera.

16:9[LETTER]: The image is displayed in 16:9letterbox.4:3[CROP]: The image is displayed in 4:3 edge crop.4:3[SQUEEZE]: The image is displayed in 4:3

squeeze.

SETUPSelect whether 7.5IRE setup is added to output signals.

ON: Outputs signals with 7.5IRE setup added.OFF: Outputs signals with no 7.5IRE setup added.

< V I D E O O U T > H D - R G B / C O M P O N EN T > F O R M AT

S Y N C T Y P E

S D - V I D E O / S V I D E O I M G S I Z E S E T U P

YP BP R

SYNC

1 6 : 9 [ L E T T E R ]O FF


30/73


STATUS Menu30

Note

The SETUP item does not appear when an HD signal of1080/50i or 720/50P format is output.

STATUS MenuThe STATUS menu is used to display the settingsselected with the menus.

The STATUS menu consists of PAGE1 to PAGE6.You can switch the pages with the B or b button.This menu only displays the current menu settings, andyou cannot change them with the menu.

PAGE1: Shows the settings selected with theEXPOSURE menu.

PAGE2: Shows the settings selected with the COLORmenu.

PAGE3: Shows the settings selected with the PICTUREmenu.

PAGE4: Shows the settings selected with the FOCUSand SYSTEM menus.

PAGE5: Shows the settings selected with the PAN TILTZOOM menu.

PAGE6: Shows the settings selected with the VIDEOOUT menu, status of the fan motors, the firmware

versions of the BRC-Z330.

< S TAT U S > E X P O S U R E

A E S P E E D A G C L I M I T I R I S L I M I T E X - C O M P B A C K L I G H T S P O T L I G H T C O L O R A E ND FILTER

PA G E 1F U L L A U TO

MI D1 2 dBF1 1

OFF OOF FOF F

OFF OOF F


31/73

O p er a t i on U s i n g t h e S u p pl i e d R

em o t e C om

m an d er

Turning on the Power 31

Before operating, check that the camera and peripheraldevices are properly installed and connected.

For details, see “Installation” (page 43) and“Connections” (page 51) .

Turning on the Power

1 Connect the camera to an AC outlet using thesupplied AC power adaptor and power cord.The power is turned on and the POWER lamplights.The camera will automatically pan and tilt and bereset to the position stored in POSITION 1 (Pan/tiltreset action).

2 Turn on the peripheral devices.

To turn on/off the camera using theRemote CommanderAs long as the camera is connected to an AC outlet, youcan turn the camera on or off with the POWER switchon the Remote Commander.

When you turn the power off using the RemoteCommander, the POWER lamp turns off and theSTANDBY lamp lights on the camera.

Note

When you turn off the camera using the RemoteCommander, the camera tilts downward to protect thelens from dust before entering Standby mode. WhenIMG-FLIP is set to ON in the SYSTEM menu, however,the camera tilts the opposite way so that the lens facesdownward when the camera is installed suspended froma ceiling.

Operation Using the SuppliedRemote Commander

RGB/COMPONENT

VISCARS-422

1 2 3 4 5 6 7 8 9

EXTSYNCIN

VIDEO

IR SELECT

75

123

OFF ON

DATA MIXOFF ON

INVISCA RS-232COUT SVIDEO

!

DC IN 12V

R

to AC outlet POWER lights

POWER

CAMERA SELECT

1 2 3

AUTO

BACK LIGHT

MANUALFAR

FOCUS

NEAR

DATA SCREEN

POWER STANDBY lights


32/73

Oper at i onUs i ngt h eS uppl i ed Remot eC om

mand er

Pan/Tilt and Zoom Operation32

Pan/Tilt and ZoomOperation

Panning and Tilting

1 Press the POWER switch.The camera will turn on and perform the pan/tiltreset action automatically.

2 Press the arrow button to pan or tilt the camera.While checking the picture on the screen, press thedesired arrow button.To move the camera little by little, press thebutton just for a moment.To move the camera in a wide range, press and

hold the button.To move the camera diagonally, press the B or b button while holding down the V or v button.

When you perform a pan/tilt operation while thecamera is in Telephoto mode, the movement speedwill be decreased. If in Wide mode, the movementspeed will be increased.

To face the camera back to the frontPress the HOME button.

If you accidentally move the camera withyour handPress the PAN-TILT RESET button to perform the pan/ tilt reset action.

If the camera moves in a differentdirection from that you intendedThe camera is preset to face toward the right wheneverthe b button is pressed. You might wish to face thecamera toward the opposite direction from that of thebutton you pressed, for example, when you change the

direction of the camera while checking the picture on thescreen. In such a case, press the 2 (REV) button whileholding down the L/R DIRECTION SET button.To reset the setting, press the 1 (STD) button whileholding down the L/R DIRECTION SET button.

Note

The setting above only changes the signal emitted fromthe Remote Commander, and does not change the settingof the camera itself. Therefore, repeat the setting foreach Remote Commander if you are using more thanone Remote Commander.

If the STANDBY lamp of the camera

flashesWhen the camera is moved or turned by hand or byexternal shock, the microcomputer inside the cameramay not be able to memorize the pan/tilt positionproperly and the camera may stop.To reset the pan/tilt position, press the PAN-TILTRESET button or turn the power of the camera off andturn it on again.

P O W E

R

C A M E

R A S E

L E C T

1

2

3

A U T O

P O S I T

I O N

H O M E

R M - E V

1 0 0

P R E S

E T

S T D

R E V

B A C K

L I G H T

M A N U

A L

F A R

F O C U

S N E

A R

W T

W T

3

4 5

6

P A N - T

I L T

S L O W

F A S T

Z O O M

L / R

D I R E

C T I O

N S E

T

P A N -

T I L T

R E S E

T

D A T A

S C R E

E N

R E S E

T 2 1

1

2STD

REV

HOME

PAN-TILTRESET

L/R DIRECTIONSET

CAMERA SELECT

Arrow button Movement of thecamera

Setting

L/RDIRECTION SET

STD

1

While holding down

Press.

L/RDIRECTION SET

REV

2

While holding down

Press.

STANDBY flashes


33/73


em o t e C om

m an d er

Adjusting the Camera 33

ZoomingPress either of the ZOOM buttons.

Note

When you perform pan/tilt operation while the camera isin the telephoto mode, the moving speed of the image onthe screen may be a little jerky.

Operating Multiple Cameras withthe Remote Commander

1 Set the IR SELECT switch on the rear of the camerayou want to operate to 1, 2 or 3.

2 Press the CAMERA SELECT button on theRemote Commander that corresponds to thenumber set in step 1.

Then, you can operate the camera(s) specified bynumber. Every time you operate the camera(s) using theRemote Commander, the CAMERA SELECT buttonpressed in step 2 lights.

Adjusting the Camera

Focusing on a Subject

To focus the camera on a subjectautomaticallyPress the AUTO button.The camera focuses on the subject at the center of thescreen automatically.

To focus the camera on a subjectmanuallyAfter pressing the MANUAL button, press either theFAR or the NEAR button to have the camera focus onthe subject.

PAN-TILTRESET

RM-EV100

SLOW FASTZOOM

L/RDIRECTION SET

TT

WWSubject appears

farther away.(Wide angle)

Subject appearscloser.(Telephoto)

Zooms in or outslowly

(SLOW side)

Zooms in orout fast(FAST side)

123

IR SELECT

POWER

CAMERA SELECT

1 2 3

AUTO

BACK LIGHT

MANUALFAR

FOCUS

NEAR

DATA SCREEN

CAMERASELECT

P O W E

R

C A M E

R A S E

L E C T

1

2

3

A U T O

P O S I T

I O N

H O M E

R M - E V

1 0 0

R E S E

T

P R E S

E T

S T D

R E V

F A R

F O C U

S

W T

W T

1 2 3

4 5

6

P A N - T

I L T

S L O W

F A S T

Z O O M

L / R

D I R E

C T I O

N S E

T

P A N - T

I L T

R E S E

T

D A T A

S C R E

E N

N E A R

M A N U

A L

B A C K

L I G H T

AUTO

FAR

NEAR

BACK LIGHT

MANUAL

CAMERA SELECT

1 2 3

AUTO

DATA SCREEN BACK LIGHT

MANUALNEARFAR

FOCUSFocusing on a far subject

Focusing on a near subject


34/73

Oper at i onUs i ngt h eS uppl i ed Remot eC om

mand er

Storing the Camera Settings in Memory – Presetting Feature34

Shooting with Back LightingWhen you shoot a subject with a light source behind it,the subject becomes dark. In such a case, press theBACK LIGHT button.To cancel the function, press the BACK LIGHT buttonagain.

Note

The BACK LIGHT function is not effective if MODE isset to MANUAL in the EXPOSURE menu of thecamera.

Storing the CameraSettings in Memory– Presetting FeatureUp to six combinations of settings (six positions)including camera position, zooming, focusing, andbacklighting, can be preset.

Note

The camera can store up to sixteen combinations ofsettings (sixteen positions) in the memory, but thesupplied Remote Commander supports preset of sixpositions only (POSITION 1 to 6). Use the RM-BR300Remote Control Unit (not supplied) to store the settingsin POSITION 7 to 16.

For details of the camera settings to be preset, see

“Presetting Items” on page 64 .

1 Press the PAN-TILT RESET button to reset the pan/ tilt position.

2 Adjust the position, zooming, focusing andbacklighting of the camera ( pages 32 to 33).

3 While holding down the PRESET button, press anyof the POSITION buttons, 1 to 6, in which you wantto store the settings.

The message “PRESET No.xx” (selectedPOSITION number) is displayed for about 2seconds.

AUTO

DATA SCREEN

STD REV

BACK LIGHT

1 2 3

MANUALNEARFAR

FOCUS

Subject appears brighter.

P O W E

R

C A M E

R A S E

L E C T

1

2

3

A U T O

P O S I T

I O N

H O M E

R M - E V

1 0 0

S T D

R E V

B A C K

L I G H T

M A N U

A L

F A R

N E A R

W T

W T

1 2

3

4 5

6

P A N - T

I L T

L / R

D I R E C

T I O N

S E T

P A N - T

I L T

R E S E

T

D A T A

S C R E

E N

RESET R E S E

T

P R E S

E T

S L O W

F A S T

Z O O M

F O C U

S

2

2

1

3 POSITION 1-6

3 PRESET

DATA SCREEN

POSITION

STD REV

BACK LIGHT

1 2 3

4 5 6RESETPRESET

While holding down

Press a POSITIONbutton.


35/73


em o t e C om

m an d er

Storing the Camera Settings in Memory – Presetting Feature 35

To recall the stored settingsPress any of the POSITION buttons, 1 to 6, in which youhave stored the settings.

To cancel the preset memoryWhile holding down the RESET button, press thePOSITION button from which you want to cancel thesettings.

Notes

• When the power is turned on, the camera starts withthe settings stored in POSITION 1.

• If you want to retain the previous pan and tiltpositions, etc. when the power is turned off and turnedon again, store those positions in POSITION 1.

• Storing or canceling the settings in POSITION 1 takesabout 2 seconds longer than those of other positions.

• When you are storing or canceling the settings in onePOSITION, you cannot call up, store or cancel thesettings in another POSITION.

DATA SCREEN

POSITION

STD REV

BACK LIGHT

1 2 3

4 5 6RESETPRESET

While holding down

Press a POSITIONbutton.


36/73

Oper at i onUs i ngt h eRM-B R3 0 0 Remot eC ont r ol Uni t

Turning on the Power36

Before operating, check that the camera, the RM-BR300Remote Control Unit and peripheral devices areproperly installed and connected.

For details, see “Installation” (page 43) and“Connections” (page 51) .

Turning on the Power

1 Connect the camera to an AC outlet using thesupplied AC power adaptor and power cord.The power is turned on and the POWER lamplights.The camera will automatically pan and tilt and bereset to the position stored in POSITION 1 (Pan/tiltreset action).

2 Press the ON/OFF switch on the RM-BR300Remote Control Unit to turn it on.The CAMERA button representing the camerawhose power was turned off last lights. (TheCAMERA 1 button lights by default.)

3 Turn on the peripheral devices.

Note

Be sure to turn on the power for the camera before thepower for the Remote Control Unit. Otherwise, the

Remote Control Unit may not recognize the connectedcamera.

To turn on/off the camera using the RM-BR300 Remote Control UnitAs long as the camera is connected to an AC outlet, youcan turn the camera on or off with the POWER button onthe Remote Control Unit.While holding down the POWER button, press theCAMERA button corresponding to the camera whosepower you want to turn on/off.When you turn the power off using the Remote ControlUnit, the POWER lamp turns off and the STANDBYlamp lights on the camera.

Note

When you turn off the camera using the RemoteCommander, the camera tilts downward to protect thelens from dust before entering Standby mode. WhenIMG-FLIP is set to ON in the SYSTEM menu, however,the camera tilts the opposite way so that the lens facesdownward when the camera is installed suspended froma ceiling.

To illuminate the panel of the RemoteControl UnitPress the PANEL LIGHT button. All the POSITIONbuttons and CAMERA buttons light.To turn off the illumination, press the PANEL LIGHTbutton again.

Operating Multiple CamerasBefore operating, you must assign the camera addressesto the connected cameras as follows. Then you canswitch the camera to be controlled simply by pressingthe corresponding CAMERA button.

Operation Using the RM-BR300Remote Control Unit

1

19

LOCK

MODE

VALUE

RESET

MENU

PRESET

SHIFT

L/RDIRECTION

PANELLIGHT

BLACKLIGHT

PAN-TILTRESET

ONEPUSHAWB

POWERAUTOMANUAL

AUTO

ONEPUSHAF

2 3 4 5 6 7

210

STD REV

311

4

POSITION

CAMERA

12513

614

715

816

R– +

BRIGHT

B– +

FOCUS

N EAR FAR

1 2 PANEL LIGHT

POWER CAMERA

RESET

STANDBY lights.

PANEL

LIGHT


37/73

O p er a t i on U s i n g t h eRM-BR

3 0 0 R

em o t e C on t r ol Uni t

Pan/Tilt and Zoom Operation 37

To assign camera addressesautomatically

1 Make sure that the camera address selector on thebottom of each camera is set to “0.”

For setting the camera address selector, seepage 14 .

2 Turn on the power of all the connected cameras andthe RM-BR300 Remote Control Unit.

3 Hold down the RESET button and press thePOWER button on the Remote Control Unit.The Remote Control Unit recognizes the connectedcameras and assigns them camera addresses 1 to 7automatically in the connected order.

4 Press the POWER button on the Remote ControlUnit and check that the CAMERA buttons light.The number of the lit CAMERA buttons indicateshow many cameras have the addresses assigned.Now you can switch the camera you want to controlwith the Remote Control Unit by pressing theCAMERA button.

To assign camera addresses manuallySet one of the camera addresses, 1 to 7, using the cameraaddress selectors on the bottom of each camera.

For setting the camera address selectors, see page 14 .

Pan/Tilt and ZoomOperation

Panning and Tilting

1 Turn on the power of the camera and the RM-BR300 Remote Control Unit.The camera will turn on, performing the pan/tiltreset action automatically.

2 Press the CAMERA button corresponding to thecamera you want to operate.

3 Operate the joystick to pan or tilt the camera.While checking the picture on the screen, inclinethe joystick in the desired direction.The panning/tilting speed changes according to the

angle at which you incline the joystick.Release the joystick to stop panning/tilting.

To set a limit on the maximum panning/ tilting speedYou can limit the panning/tilting speed obtained whenyou incline the joystick at the maximum angle.

1 Hold the PAN-TILT RESET button for more than asecond while pressing the SHIFT button.All of the CAMERA buttons 1 to 7 flash.

2 Press the CAMERA button corresponding to thespeed you want to set, as shown in the table below.

CAMERA button Maximum panning/tiltingspeed

1 4.4 degrees/sec.

2 6.7 degrees/sec.

3 11.6 degrees/sec.

4 18.6 degrees/sec.

5 29.2 degrees/sec.

1

19

LOCK

MODE

VALUE

RESET

MENU

PRESET

SHIFT

L/RDIRECTION

PANELLIGHT

BLACKLIGHT

PAN-TILTRESET

ONEPUSHAWB

POWERAUTO

MANUAL

AUTO

ONEPUSHAF

2 3 4 5 6 7

210

S TD R EV

311

4

POSITION

CAMERA

12513

614

715

816

R– +

BRIGHT

B– +

FOCUS

N E AR F AR

32

1L/R DIRECTION

STD

REV

PAN-TILT RESET

POWER SHIFT


38/73

Oper at i onUs i ngt h eRM-B R3 0 0 Remot eC ont r ol Uni t

Pan/Tilt and Zoom Operation38

Only the CAMERA button you pressed flashes, andthe corresponding maximum panning/tilting speedis set.

Note

The maximum panning/tilting speed setting is stored inthe memory of the optional RM-BR300 Remote ControlUnit. If you use another RM-BR300 Remote ControlUnit or you connect another camera to the RM-BR300,set a limit on the maximum panning/tilting speed again.

To face the camera back to the frontPress the button on the top of the joystick for one or twoseconds.

If you accidentally move the camera withyour handPress the PAN-TILT RESET button to perform the pan/ tilt reset action.

If the camera moves in a differentdirection from that you intendedThe camera is preset to face toward the right wheneverthe joystick is inclined to the right. You might wish toface the camera toward the opposite direction from thatin which you inclined the joystick, for example, whenyou change the direction of the camera while checkingthe picture on the screen. In such a case, press the

POSITION 2 (REV) button while holding down the L/RDIRECTION button.To reset the setting, press the POSITION 1 (STD) buttonwhile holding down the L/R DIRECTION button.

Note

The setting above only changes the signal emitted fromthe RM-BR300 Remote Control Unit, and does notchange the setting of the camera itself.

If the STANDBY lamp of the cameraflashesWhen the camera is moved or turned by hand or byexternal shock, the microcomputer inside the cameramay not be able to memorize the pan/tilt positionproperly and the camera may stop.To reset the pan/tilt position, press the PAN-TILT

RESET button or turn the power of the camera off andturn it on again.

6 43.4 degrees/sec.

7 60 degrees/sec.

CAMERA button Maximum panning/tiltingspeed

Press for 1 or 2 seconds.

Joystick Movement of thecamera

Setting

19

STD

L/RDIRECTION

Incline to the right. While holding down

Press.

210

REV

L/RDIRECTION

Incline to the right. While holding down

Press.

STANDBY flashes.


3

brc z330 operating instructions (1)

Documents