brick as a building material
TRANSCRIPT
1
BRICKSSUMITTED BY::TUSHAR KACHHADIYA
SMIT PANCHALSARYU PATELRONAK JAIN
2
WHAT IS BRICK?•A brick is building material used to make walls, pavements and other elements in masonry construction. Traditionally, the term brick referred to a unit composed of clay, but it is not used denote any rectangular units laid in mortar.
3
Bricks are made chiefly from clay and shale. •Clay is plastic earth, is constituted largely of sand an alumina and may contain various quantities of chalk, iron, manganese, dioxide, etc.•Shale is soft finely stratified sedimentary rock that formed from consolidated mud or clay and can be split easily into fragile plates
Shale Clay
INTRODUCTION
4
Following factors affect the strength of bricks:•Composition of brick earth•Preparation of clay and blending of ingredients•Nature of moulding adopted•Care taken in drying and stacking of raw or green
bricks•Type of kiln used including type of fuel and its feeding•Burning and cooling processes •Care taken unloading
STRENGTH OF BRICKS
5
•Better thermal insulation•Economical•Masonry is easier, faster and stronger•Bricks have greater fire resistance • Its size enables easy handling and placement in walls.• It can be easily adapted to small scale and large scale
structure to give pleasing appearance and texture.• It enhances good sound absorption•Very low maintenance cost is required
ADVANTAGES OF BRICKS
6
•Time consuming construction•Cannot be used in high seismic zones•Very less tensile strength•Since bricks absorbs water easily, therefore it causes fluorescence when not exposed to air•Rough surfaces of bricks may cause mould growth if not properly cleaned
DISADVANTAGES OF BRICKS
7
• Colour• Texture • Porosity• Fire resistance• Size variations• Compressive strength• Absorption
PROPERTIES OF BRICKS
8
USES OF BRICKS1. Construction of walls of any size.
2. Construction of floors.
9
USES OF BRICKS3. Construction of arches and cornices.
4. Construction of brick retaining wall.
10
USES OF BRICKS5. Manufacture of surkhi (powder bricks).
6. Staircase
11
USES OF BRICKS7. Foundation.
8. Masonry veneer walls.
12
Burnt bricks Unburnt bricks
First class bricks Second class bricks Third class bricksFourth class bricks
Bricks used in construction works are burnt bricks and they are classified into the following four categories.
CLASSIFICATION OF BRICKS
13
First class bricks:
• These bricks are table- moulded and of standard shape.
• The surfaces and edges of the bricks are sharp, Square, smooth and straight.
• They complete with all the qualities of good bricks.
• These bricks are used for superior work of permanent nature.
CLASSIFICATION OF BRICKS
14
Second class bricks:
• These bricks are ground moulded and they are burnt in kilns.
• The surface of these bricks is some what rough and shape is also slightly irregular.
• These bricks are commonly used at places where brickwork is to be provided with a coat of plaster.
CLASSIFICATION OF BRICKS
15
Third class bricks:
• These bricks are ground moulded and they are burnt in clamps.
• These bricks are not hard and they have rough surfaces with irregular and distorted edges.
• These bricks gives dull sound when stuck together.
• They are used for unimportant and temporary structures and it places where rainfall is not heavy.
CLASSIFICATION OF BRICKS
16
Fourth class bricks:
• These bricks are used as aggregate for concrete in foundation, floors, roads etc.
• These bricks are over burnt with irregular shape and dark in colour.
• Because of the fact that the overburnt bricks have a compact structure and hence, they are sometimes found to be stronger than even the first class bricks.
CLASSIFICATION OF BRICKS
17
TYPES OF BRICKS1. Ordinary bricks: They are rectangular solids.
2. Curved sector bricks: these bricks are in the form of curved sector and they are used in the construction of circular brick masonary, pillars, brick chimneys.
18
2. Curved sector bricks:
TYPES OF BRICKS
19
3. Channel bricks: these bricks are moulded to the shape of a gutter or a channel and they are very often glazed. These bricks are used to function as drains.
TYPES OF BRICKS
20
4. Coping bricks: these bricks are made of suit the thickness of walls on which coping is to be provided. Such bricks take various forms such as chamfered, half round or saddle-back.
TYPES OF BRICKS
21
5. Bull nose bricks: A brick moulded with a rounded angle is termed as a “bull nose”. It is used for a rounded quoin. A connection which is formed when a wall takes a turn is known as a quoin. The centre of the curved portion is situated on the long centre line of brick.
TYPES OF BRICKS
22
6. Hollow bricks:
• These are also known as cellular or cavity bricks. • Such bricks have wall thickness of about 20 cm to 25cm.
• They are prepared from special homogeneous clay.
• They are light in weight about one-third the weight of the ordinary brick of the same Size.
• These bricks can be laid almost about four times as fast as they ordinary bricks and thus the use of such bricks leads to speedy construction.
• They also reduce the transmission of heat, sound and damp. They are used in the construction of brick partitioning.
TYPES OF BRICKS
23
6. Hollow bricks:
TYPES OF BRICKS
24
7. Paving bricks: • These bricks are prepared from clay containing a higher percentage of iron.
• Excess iron vitrifies the bricks at a low temperature.
• Such bricks resists better the abrasive action of traffic.
• Paving bricks may be plain or chequered.
TYPES OF BRICKS
25
8. Perforated bricks: • These bricks contain cylindrical holes throughout their thickness.• these bricks are light in weight and they require less quantity of clay for their
preparation.• The dying and burning of these bricks are also easy.• The perforated bricks are used in the construction of brick panels for light weight
structures and multistoried framed structure.• The perforation may be circular, square, rectangular or any other regular shape in cross
section.
TYPES OF BRICKS
26
9. Purpose-made bricks: • In order to achieve certain purpose, these bricks are made.• The arch brick are made of wedge shape to keep mortar joint of uniform thickness.• The ornamental brick are prepared for corbels, cornices.• The gutter bricks are used to construct gutter.• The plinth bricks are used to emboss the plinth level.• These bricks are usually more costly than the ordinary bricks but they grant safe, • clean and quick construction.
TYPES OF BRICKS
27
10. Queen closer bricks: • The queen closer is usually placed next to the first brick in header course. The queen
closer-1/2 is obtained by cutting an ordinary brick into half bats and then splitting one into half.
• The queen closer quarter is more often used than queen closer-half as it is easier to cut, all though it is generally produced a 56mm wide continuous vertical joint.
TYPES OF BRICKS
28
11. King closer bricks: The king closer is formed by removing a corner and leaving half-header and half stretcher faces.
12. Mitred bricks:These are used only in exceptional cases when the ends are required to be mitred.
13. Splay bricks:These are used only in exceptional cases when the ends are required to be mitred.
TYPES OF BRICKS
29
14. Dogleg / angle : • This brick are used to ensure a satisfactory bond at quoins which depart from a • right angle and to be prepared to the mitred closers. • The angle and lengths of faces forming the dogleg vary.
TYPES OF BRICKS
30
15. WirecutThe clay is continuously extruded to a required size and shaope and then cut into individual bricks by means of a wire, much like a cheese is cut by cheesewire.Thousands of variations in colour and texture. Usually the cheapest facings available as the manufacturing process is highly automated.
TYPES OF BRICKS
31
TYPES OF BRICKS16. StockThe clay is wetted to a so-called "soft mud“ and then moulded to shape, before being allowed to dry prior to firing in the kiln. Much of the process is automated. Tend to be slightly irregular in shape. Usually a bit more expensive than wirecuts.
17. HandmadeUsually made on a bench, in a mould, much as described above for a stock brick Because the clay isn't firmly compacted by machine, each brick normally hasdistinctive creasing known as a 'smile'. Very desirable, and the most expensive of the facings, but well worth it on prestige jobs.
32
• Good bricks should be thoroughly burnt, this makes them hard and durable
• A hard ringing sound emitted when two bricks are stuck together indicates that they have been brunt satisfactorily.
• Bricks should be true to size and shape, with straight edges and even surfaces.
• They should be free from cracks, chips, and larger particles of lime.
• Brick when broken should show a bright homogeneous and compact structure free from voids.
• Brick should not absorb water more than 20% by weight for 1st brick and 22% by weight from 2nd brick, when soacked in cold water for a period of 24 hours.
CHARACTERISTICS OF BRICKS
33
• No impression should be left on brick surface when it is scratched with finger nail.
• Brick should not break when dropped flat on hard ground from a height of about 1m.
• Bricks should have low thermal conductivity and they should be sound proof.
• Brick when soacked in water for 24 hours should not deposited of white salt when allowed to dry in shape.
CHARACTERISTICS OF BRICKS
34
BRICK BONDSStretcher BondOriginally used for single brick walls, it became the obvious choice for cavity walls with the least amount of cutting required. It is therefore the most economical bond pattern and is extensively used in modern building.
35
BRICK BONDSHeader BondA brick course laid flat with the short end of the brick exposed. This method is particularly strong as the width of the wall is the whole length of a brick. Historically it was used for buildings of high quality, often used for curved brickwork.
36
BRICK BONDSEnglish BondIt comprises of alternative courses of headers and stretchers. It provides a strong bond when the wall is one brick thick. It is the preferred bonding pattern for bridges, viaducts, embankment walls and other civil engineering architectures
37
BRICK BONDSFlemish BondFlemish bonds can be replicated in the half-brick outer leaf of a cavity wall by using whole bricks as stretchers, while the headers are created by half bricks called bats or snap-headers. It is not as strong as English bond at one brick thick.
38
With solid or perforated bricks, the orientation of the brick doesn't matter, but with frogged bricks, the frog should always be laid uppermost. This ensures that the loading of the wall is evenly spread across its width, rather than being concentrated onto the edges, and that there are no voids within the brickwork that could be weak spots.
BRICK BONDS
39
MANUFACTUCTING PROCESS
40
MANUFACTUCTING PROCESS
41
MANUFACTUCTING PROCESS
42
MANUFACTUCTING PROCESS
43
Pug mill used for tempering of clay
MANUFACTUCTING PROCESS
44
MANUFACTUCTING PROCESS
45
MANUFACTUCTING PROCESS
46
MANUFACTUCTING PROCESS
47
HAND MOULDING
MANUFACTUCTING PROCESS
48
MANUFACTUCTING PROCESS
49
MANUFACTUCTING PROCESS
50
MACHINE MOULDING
MANUFACTUCTING PROCESS
51
DRYINGMANUFACTUCTING PROCESS
52
MANUFACTUCTING PROCESS
53
BURNINGMANUFACTUCTING PROCESS
54
MANUFACTUCTING PROCESS
55
MANUFACTUCTING PROCESS
56
MANUFACTUCTING PROCESS
57
MANUFACTUCTING PROCESS
58
MANUFACTUCTING PROCESS
59
MANUFACTUCTING PROCESS
60
MANUFACTUCTING PROCESS
61
MANUFACTUCTING PROCESS
62
MANUFACTUCTING PROCESS
63
MANUFACTUCTING PROCESS
64
MANUFACTUCTING PROCESS
65
MANUFACTUCTING PROCESS
66
COLOURS OF BRICKS Table shows the colours produced by clays with various constituents.
COLOUR CONSTITUENTS PRESENT IN CLAYBlack Manganese and large proportion of iron
Bluish green Alkalis ( burnt at high temperature)
Bright red, dark blue or purple
Large amount of iron oxide
Brown Lime in excess
Cream Iron and little lime
Red Iron in excess
White Pure clay
Yellow Iron in magnesia
67
Colours of bricks, as obtained in its natural course of manufacture, depend on the following factors:
1. Degree of dryness achieved before burning.2. Natural colours of clay and its chemical composition3. Nature of sand used in moulding operation4. Quality of fuel used in burning operation5. Quality of air admitted to the kiln during burning.6. Temperature at which bricks are burnt.
COLOURS OF BRICKS
68
The length of brick should be twice its width plus the thickness of one vertical joint in order that a proper bond may be maintained. Brick in common use vary in size from 210 to 230mm long by 100 to 115 mm wide by 38 to 75 mm thick.
Clay bricks are mostly 230 X 115 X 75 mm, using a 10mm joint this gives a nominal size or format of 240 X 125 X 85 mm.
BRICKS
69
Fire clay:• Fire clay is refractory clay which is capable or resisting a high
temperature without being melted or softened. • It is used for making refractory material.• A refractory material is able to stand a high temperature
without losing its shape.• Thus fire clay is used in manufacture of fire bricks, crucibles,
lining construction of a good fire-clay are two- alumina and silica.
BRICKS
70
Depending upon the fire resistance capacity, fire clays are classified into the following three categories.
1. High duty fire clay: These clay can resist temperature range of 1482C to 1648C.
2. Medium duty fire clay: These clay can resist temperature range of 1315C to 1482C.
3. Low duty fire clay: These clay can resist temperature upto 870C only.
BRICKS
71
Fire bricks :• Fire bricks are made from fire clay, process of manufacture is the same as that
of ordinary clay bricks. Burning and cooling of fire-bricks are done gradually.
BRICKS
72
Following are varieties of fire bricks:
1.Acidic bricks2.Basic bricks3.Neutral bricks
BRICKS
73
1. Absorption2. Crushing strength3. Hardness4. Presence of soluble salts5. Shape and size 6. Soundness7. Structure
TEST ON BRICK
74
Absorption• Water absorption is brick is carried out by immersing it in water for 24
hours.• It is again weighed and the different is in indicated the amount of water
absorbed by brick.• It should not in any case exceed 20% of wet of dry bricks.
TEST ON BRICK
Crushing Strength• Crushing strength of brick is found out by placing it in compressive test
machine.• It is pressed till it breaks• The minimum crushing strength of brick is 55kg/cm2• In this test, a stretch is made on brick surface with the help of finger nail.• If no impression is left on surface, the brick is treated to be sufficiently
hard.
75
Presence of soluble salts
• The soluble salts, if present in bricks will cause efflorescence in the surface of bricks.
• For finding out the presence of soluble salts in a brick, it is immersed in water for 24 hrs.
• It is than taken out and allowed to dry in shed.• The absence of grey or white deposits in its surface indicates absence of
soluble salts.• It the white deposit cover about 20% surface, the efflorescence are said to
be as moderate, when deposits are to be more than50% the efflorescence become heavy and it is treated as serious when such deposits are converted into powdery mass.
TEST ON BRICK
76
Soundness• In this test, two bricks are taken and than struck together with each
other, the bricks should not break and a clear ringing sound should be produced.
TEST ON BRICK
Structure• A brick is broken and its structure is examined.• It should be homogeneous, compact and free from any defects.
77
THANK YOU