bridge wave
DESCRIPTION
Bridge wave rectifier minor project reportTRANSCRIPT
IntroductionA diode bridge is an arrangement of four (or more) diodes in a bridge circuit configuration that provides the same polarity of output for either polarity of input.
When used in its most common application, for conversion of an alternating current (AC) input into a direct current (DC) output, it is known as a bridge rectifier. A bridge rectifier provides full-wave rectification from a two-wire AC input, resulting in lower cost and weight as compared to a rectifier with a 3-wire input from a transformer with a centre-tapped secondary winding
For many applications, especially with single phase AC where the full-wave bridge serves to convert an AC input into a DC output, the addition of a capacitor may be desired because the bridge alone supplies an output of pulsed DC
The function of this capacitor, known as a reservoir capacitor (or smoothing capacitor) is to lessen the variation in (or 'smooth') the rectified AC output voltage waveform from the bridge. There is still some variation, known as ripple. One explanation of 'smoothing' is that the capacitor provides a low impedance path to the AC component of the output, reducing the AC voltage across, and AC current through, the resistive load. In less technical terms, any drop in the output voltage and current of the bridge tends to be cancelled by loss of charge in the capacitor. This charge flows out as additional current through the load. Thus the change of load current and voltage is reduced relative to what would occur without the capacitor. Increases of voltage correspondingly store excess charge in the capacitor, thus moderating the change in output voltage / current.
Components Required
SR.No.
Name Specification Quantity
1 Step down transformer
230V to 12V or 110V to 12V
1
2 Diodes N4007 4 3 Capacitor 470µF 1 4 Led 1 Red 1 5 Resistor 1K 1
Circuit Diagram
Working of a Bridge Rectifier
During the positive half cycle of secondary voltage, diodes D2 and D3 are forward biased and diodes D1 and D4 are reverse biased. Now the current flows through D2–>Load–>D3
During the negative half cycle of the secondary voltage, diodes D1 and D4 are forward biased and rectifier diodes D2 and D3 are reverse biased. Now the current flows through D4–>Load–>D1
In both the cycles, load current flows in the same direction. Hence we get a pulsating DC voltage
Addition of a capacitor at the output converts the pulsating DC voltage to fixed DC voltage.
Up to a time period of t=1s input voltage is increasing, so the capacitor charges up to peak value of the input. After t=1s input starts to decrease, then the voltage across the capacitor reverse biases the diodes D2 and D4 and therefore it will not conduct. Now capacitor discharges through the load, then voltage across the capacitor decreases.
When the peak voltage exceeds the capacitor voltage, diodes D2 or D4 forward biases and as a result capacitor again charges to the peak value. This process continues. Hence we get almost smooth DC voltage
Output Waveforms
Advantages of Bridge Wave Rectifier
The rectification efficiency of full-wave rectifier is double of that of a half-wave rectifier.
The ripple voltage is low and of higher frequency in case of full-wave rectifier so simple filtering circuit is required.
Higher output voltage, higher output power and higher Transformer Utilization Factor (TUF) in case of a full-wave rectifier.
In a full-wave rectifier, there is no problem due to dc saturation of the core because the dc current in the two halves of the two halves of the transformer secondary flow in opposite directions.
No centre tap is required in the transformer secondary so in case of a bridge rectifier the transformer required is simpler. If stepping up or stepping down of voltage is not required, transformer can be eliminated even.
The PIV is one half that of centre-tap rectifier. Hence bridge rectifier is highly suited for high voltage applications.
Transformer utilization factor, in case of a bridge rectifier, is higher than that of a centre-tap rectifier.
For a given power output, power transformer of smaller size can be used in case of the bridge rectifier because current in both (primary and secondary) windings of the supply transformer flow for the entire ac cycle.
JSS ACADEMY OF TECHNICAL EDUCATION
PROJECT REPORT ONBRIDGE WAVE RECTIFIER
Submitted By:Shubhi Srivastava12091220834th Year (Batch 2012-16)Instrumentation and Control Department