bucket elevator - hcmuaf.edu.vn · bucket elevators and are classified as a1, a2, a3 and a4 type....

http://www2.hcmuaf.edu.vn/?ur=dangnh 1

Bucket Elevator

http://www2.hcmuaf.edu.vn/?ur=dangnh

Objectives

Definition

General Characteritics

Types of Bucket Elevators

Parts of Bucket Elevators

Capacity Calculation

Power Requirement

Gầu tải bang – xích

Others types

2


1. Definition/ Description (1)

These are powered equipment for conveying bulk materials in a vertical or steep inclined path, consisting of an endless belt, or chain/s to which metallic buckets are fixed. With the flexible belt/chain, the buckets move unidirectionally within a casing and collects bulk materials at bottom end of the equipment and delivers it at the top end.

The vertical lift may be a few meters to more than 50m.

Capacity may vary from 2 to 4 t/hour to as much as25, 50, or even 100 t/hour.

3


1. Definition (2)

4


A vertical belt-and-bucket elevator

5

1-belt; 2-bucket;3-driving pulley; 4-take-up pulley; 5-upper casing section; 6-intermediate casing sections;7-lower casing section (boot);8-manholes; 9-drive unit; 10-take-up; 11- holdback brake; 12-guides.


2. General Characteritics (1)

i. An endless pulling member- flat belt or chain.

ii. Driving and take up pulleys or sprockets at top and bottom respectively, mounted on bearings and blocks.

iii. Metal casing covering the entire elevator. It consists of head at the top, boot at the bottom and intermediate sections, all joined at flanges by fasteners.

iv. Buckets, generally made out of sheet metal, which are attached at definite pitch to the pulling member by fastners (screw and nuts, riveted etc.)

6


2. General Characteritics (2)

i. Drive at the top consisting of an electric motor, gearbox, and couplings.

ii. Hold back brake attached to the top pulley/sprocket shaft, to prevent reverse motion of the elevator when drive is stopped.

iii. Feed hopper attached to the boot for feeding materials to the elevator.

iv. Delivery/ discharge spout fixed with the top part of the casing, through which the material is discharged.

v. Manholes are provided at the casing to check operations of the elevator.

vi. Guides and guide sprockets are provided for belt and chain respectively to keep them in astraight path.

7


3. Types of bucket elevators

Bucket elevators are classified based on bucket spacing and mode of discharge of materials. As per IS:7167-1974, ‘‘Code for Selection and Use of Bucket Elevators,’’ they are classified into following three basic types.

1. Centrifugal discharge elevators (designated as type I)

2. Positive discharge elevators (designated as type III)

3. Continuous discharge elevators (designated as type II)

8


3.1. Centrifugal discharge elevators

9


3.2. Positive discharge elevators

10


3.3. Continuous discharge elevators

11


Part cover removed head section

12


3.5. Selection of type of elevator

13


4. Parts of a Bucket Elevator

14

1.HEAD SHAFT: with pulley for belting or sprockets for chain.2.THE DRIVE, gear reducer, and motor drives, which may be V-belt, AN drive chain and sprockets, or direct-coupled with flexible coupling or shaft-mounted reducer.3.FOOT SHAFT: with pulley or sprockets.4.ELEVATOR BUCKETS mounted on belt or chain5.THE ELEVATOR HOUSES the bucket and belting or chain assembly and general provide mounting and enclosure for the rotating machinery.6.PLATFORMS, LADDERS, AND HOIST BEAMS are frequently mounted on elevator housings for mainteance access.


4.1. Bucket of Bucket Elevators

The different components of a bucket elevator have been mentioned under ‘‘descriptive specification’’ in section 8.4.1 (A). The buckets used in a bucket elevator needs further elaborations

Buckets are classified into two types from consideration of their shape: Rounded bottom buckets are used in spaced bucket elevators and are classified as A1, A2, A3 and A4 type. V-type buckets are used in continuous bucket elevators, and are classified as B1, B2, B3 and B 4 type. Fig. 8.4.5 illustrates geometrical features of the various types of buckets.

Specified dimensions of these buckets namely length, projection, depth and capacity of the individual buckets are given in IS:6833-1973. Table 8.4.2 below indicates only the range of recommended dimensions of such buckets

15


4.1.1 Range of dimensions for buckets

16


4.1.2. Geometrical features of various types of buckets (1)

17


4.1.2.Geometrical features of various types of buckets (2)

18


4.1.3. Typical bucket fixing arrangement

19


4.1.4. Fixing arrangement of buckets

Fixing of buckets to belt - B.

Fixing of buckets to chains passing through back of buckets – C

Fixing of buckets to chains passing through side of buckets - DTypical bucket fixing arrangements are shown in Fig. 8.4.6.

20


4.1.5. Selection of Bucket

21


4.1.6. Belts for bucket elevator

Belts

Chains

22


4.1.7. Splicing elevator belts.

23


4.2. Elevator Head Section (1)

24

A, sprinkler head and alarm;

B, strut slanted to down leg;

C, cleanout opening;

D, inspection door;

E, lagged head pulley;

F, buckets. Belt should be

2.5 cm wider then buckets,pulley should be 2 cm widerthan belt.


4.2. Elevator Head Section (2)

25


4.3. Elevator boot section (1)

26

Most bucket elevators provide in the boot section a belt take-up device to tighten the belt as required and to train it so that it runs true and does not rub on either side of the boot. A manual screw-type takeup is most often used. On tall, heavy-capacity legs an automatic take-up boot pulley is used. This provides the correct belt tension at all times


4.3. Elevator boot section (2)

27


5. Capacity Calculation

28


Bucket Filling Factor

29


6. Power requirements

30

Q: capacity (kg/min)

H: Lift (meter)

F = 1,5 for elevators loaded on the down side of the boot,

= 1,2 for elevators loaded on the up side of the boot.

Actual horsepower requirements are 10 to 15% higher than this theoretical value because of friction, power transmission, and drive losses.


7. Gầu tải băng – Gầu tải xích:

Vận chuyển vật liệu dạngbột, hạt, cục nhỏ, khô.

Dễ nạp và tháo liệu.

Làm việc êm, tốc độchuyển động của băngtừ 0,8 – 3,5m/giây.

Năng suất đến 80m3/giờ.

H = 50m.

Hạn chế về độ bền củabăng.

31

Vận chuyển vật liệu dạng cục to, ẩm.

Khó xúc.

Làm việc nặng, tốc độ chuyển động của băng từ 0,4 – 1,6m/giây.

Năng suất đến 300m3/giờ.

Gầu 1 xích có bề rộng 160 – 250 mm, gầu 2 xích làm việc với gầu

rộng hơn.


8. Ưu nhược điểm của gầu tải

Kích thước bao trong hình chiếu bằngnhỏ, dải năng suất từ 5 – 30 m3/h.Chiều cao nâng lớn, cá biệt có thể đạtđến 75m.

Không cho phép quá tải, cấp liệu mộtcách điều hòa. Trường hợp quan trọngcần đặt thêm một gầu tải phụ.

32


9. Other types

33

bucket elevator - hcmuaf.edu.vn · bucket elevators and are classified as a1, a2, a3 and a4 type....

Documents