business concept 6tl engineering
TRANSCRIPT
6TL, has its headquarter in Barcelona (Spain), We have over 30
years expertise in delivering innovative modules for the electronics
test market.
Our products are used worldwide by first line integrators to
solve highly demanding end customer needs.
Sagrada familia by Gaudi, Engineering excellence.
6TL has developed
technology as a true modular way to
integrate test systems, based on
standard Building blocks: Hardware,
Software and engineering,
Our modules are the
solution for typical recurrent
engineering tasks that any test
engineer is facing when thinking in
a complete ATE solution and not
only in single instrument solutions.
INTEGRATORProject
END CUSTOMER
Thanks to technology,
local test systems integrators
are building up their turn-key solutions
– Faster (Time savings up to 70%)
– With lower risk and less problems
– With lower cost
– With much better performance
– With happier end customers, because of:
shorter ROI, better value for money and less maintenance
thanks to our high degree of standarization
+ Your Expertise Happy End-User
6TL develops standard products (MODULES) for every
recurrent problem into end of line ATE for electronics.
i.e. Product YAV90PNE (Pneumatic Subsystem):
6TL develops standard products (MODULES) for every
recurrent problem into end of line ATE for electronics.
i.e. Product YAV90PNE (Pneumatic Subsystem):
Air inlet
Pressure sensor
CAN bus
connector
10 electro valves
PLATFORM
SIDE (ATE)
RECEIVER
SIDE (UUT)
Control Firmware
No need for extensive engineering with 6TL
Reliable Mass interconnect
interface, VPC 90 series.
A lot of features are wanted in a test system but get not approved.
Monitoring the stability of the AC power source, phase & frequency.
Controlling the cooling fans depending on the temperature.
Measuring / monitoring the temperature during test.
Providing alarms in case of power or temperature extremes.
Build-in correct safety management (EN60947-5-1 & EN60204)
Under program control switch on/off instrumentation.
Network access for remote service and control.
Solution, modularity, as in our solution, it is all there.
Overcome a large current peak when switching on.
Create a “switch-on” sequence.
Power Distribution Unit
Under program control switch on/off instrumentation
Build resouces in your tester, not in the fixture.LED color detection
ISP, In-system programmers
Boundarty Scan XJIO (XJTAG), CION (Göpel), DIOS Jtag Techn.
Re-Usable
Oct. 2013, 6TL® Dia 22
Oct. 2013, 6TL® Dia 23
YAV90JTAG
Oct. 2013, 6TL® Dia 24
YAV90JTAG
Oct. 2013, 6TL® Dia 25
Replace DIOS
Replace Pod
YAVPack with BS Recourse unit.Sample BS SmartFixture Tester.
Oct. 2013, 6TL® Dia 26
• All our modules communicate through CanBus (minimal wiring effort),
all our modules are delivered including the NI LabView drivers
C
A
N
B
U
S
Phi6 is the software environment, based on NI tools, to manage,
control and program the modules and systems.
i.e. Phi6 EXPLORER is for modules, what MAX is for NI
instrumentation.
Designed for TEST Only each module is designed for one
purpose: To be a part of an ATE system.
Efficient wiring all modules are connected through CanBus.
Flexibility All modules are independent subsystems easy to
add/remove whenever needed.
Reliable tester interface due to full integration of a Mass
Interconnect Interface as part of our concept.
Short Signal path CanBus RF or I/O modules inside testfixture,
YAVModules directly mounted in Mass Interconnect Interface.
Fast Build-up of an ATE. Recurrent tasks in one Module, BS,
LED test, MMI, Pneumatic, Flipper, etc.
Your Engineering can focus on tasks that add value to the final
ATE system.
Short delivery due to our modularity we can deliver in 3-4 weeks
a complete “Base Test Platform”.
Test managers will face the “build vs buy”
decision when discovering the supply scope
off 6TL technology.
Why spend time looking into issues that
are already solved and proven?
Why risk a delay of production start
because you used valued engineering
time developing non core products and
solutions?
Why use skilled resources that could
be adding value in the product
development?
Why put extra pressure on
procurement to ask for separate-
quotations, orders, tracing shipments
and Delivery etc?
If the customer has a real need for the
solution, and an existing 6TL solution fits his
requirements, the decision is clear: BUY!
Development Effort And Time
= Development Time
= Time savings using
Platform design
Integration design
Mass Interconnect design
Test automation
Electrical Diagrams
Pneumatic Design
Electrical cabinet design & Build
Pneumatic cabinet
Safety integration
Data comm. interfacing
RF test design
Actuators
Traceability
Time savings up to 70%
(PC/Embed.-controller)
NI-PXI Instrumentation
Power Supply’s
UPS, etc.
TestStand + LabVIEW
MMI module &
base Platform
Mass Interconnect
Solution: RECEIVER
Fixturing
(RF or baseband)
End-User defines base
test platform together
with 6TL Engineering
Integrator ONE uses his
expertise to offer the final
solution to End-User.
Integrator TWO uses his
expertise to offer the final
solution to End-User.
End-User asks
different integrators to
quote final solution
Integrator defines full or
base test platform together
with 6TL Engineering.
Software.
Application
Integrator uses his
expertise to create the
End-User final solution
SAMPLE END-USER SOLUTIONS CREATED BY OUR CUSTOMERS
SAMPLE END-USER SOLUTIONS CREATED BY OUR CUSTOMERS
SAMPLE END-USER SOLUTIONS CREATED BY OUR CUSTOMERS
SAMPLE END-USER SOLUTIONS CREATED BY OUR CUSTOMERS
The 6TL concept together with the integrators expertise and
third party instrumentation deliver the best and most efficient ATE.
RF
DAC
In-Line
SAMPLE END-USER SOLUTIONS CREATED BY OUR CUSTOMERS
