书写纸 供应商折叠 cupti 2 manuals/vape mods...press (+) and (-) together for 2s, you can...
TRANSCRIPT
This kit includes:1. 1 x CUPTI 2
2. 1 x Second connector
3. 1 x CLOCC SS316L 0.5 Ohm
4. 1 x USB cable
5. 1 x Manual
Specification:Length: 51.5mm
Width: 42.5mm
Height: 84mm(exclude the drip tip)
Weight: 330g
Output: 5-80W
Capacity 5mL
Display: OLED
Replacement Coil: CLOCC(SS 0.5Ohm)
CLOCC(NiCr 1.5Ohm)
CLRBA(Optinal)
Charge port: Micro USB, DC 5V/1.5A (Max)
resistance: 0.1 - 2.5 Ohm
Color: Black/White/Silver
TC mode: NI/TI/SS/TC
53*75mm 书写纸 供应商折叠
CLOCC/CLRBA installation (Diagram) Operation:1. 5 speedy clicks to switch on/off the battery.
2. After switched on, OLED displays “KangerTech” at
standby mode.
3. Cell reverse protection, no power output when cell
reversely installed.
4. Press fire button 3 times, choose resistance wire, Ni, Ti,
SS, TC or pure wattage output.
5. For pure Ni, Ti, TC or SS resistance wire, you can set
your desired coil temperature to fit your taste.
6. For power output mode, set your desired working
wattage that best fits you.
7. Press (+) and fire button together to choose OLED
display orientation.
8. Press fire button and (-) together can lock the up and
down button once you have best setting.
9. Press (+), (-) together for 2s for temperature curve
or power curve mode,
10. This device can be adjusted by software , you can
customize the temperature or power curve mode
that best fits you.
11. You can modify the Working interface/Function
display/Screen brightness through program.
12. When 2 batteries have different voltages, the indicator
is subject to the lower value with "!" .
13. In case you change the coil or vape in other
environment of presetting, you need to calibrate
the atomizer as new coil: New Coil(+), Old Coil (-) for
best performance.
14. If no display of calibration:
a. Screw off the coil.
b. Press the fire button till OLED displays “Check Atomizer”.
c. Screw back the atomizer and press fire button again.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
LCD display:Process LCD Display Function Explanation
Battery on / off
At temperature control of Ni 200 (pure Nickel), Ti (Titanium), SS (Stainless steel),TC(for customized), you can adjust desired temperature.
Open circuit
Long time pressing
High Temperature protection
Sequence of tempertaure control wire type: Ni: Pure NickelTi: TitaniumSS: Stainless steelTC: for customized
Use the up or down small button and to chooseNew coil: up (+) buttonOld coil: down (-) button
Temperature control off
Choose the best OLED display for the left or right hand holding
18650 cell needs to be recharged
Short circuit pretoction
Press (+) and (-) together for 2s, you can enter temperature or power curve mode
There are only two options.
For long period storage
Prevent over time firing
Prevent over heating of control board
In case successive vaping causes the control board over heating, it will disappear once cooled down
Battey in off mode
This is to calibrate the coil resistance for Ni 200 , Ti , SS or other coil, make sure the coil in the room temperature (the environment you vape) for best temperature control.
Apart from the 4 temperature control modes, the final mode is full power wattage output, which is the last setting behind the temperature control selection of NC mode.
To reverse the OLED display, switch on CUPTI 2, press fire button and (+)together for 2 seconds.
In using Ni/Ti/SS/TC resistance wire, once changing the coil, CUPTI 2 will detect your coil value automatically
When battery is switched off, press fire button 5 times within 2 seconds to switch on the battery.
Choose your preferred coil resistance type, which contains Ni: Nickel 200, Ti: Titanium, SS: Stainless steel, or other coil wire, once the coil is chosen, it will run in temperature control mode with the pre-set temperture value. It is reminded that user must choose the right coil wire and corresponding mode for proper function.
Once set the desired temperature, CUPTI 2 mod will cut off the output if the coil reaches your preset temperature.
To select temperature control materials, switch on the CUPTI 2, press 3 successive clicks on fire button. Another 3 successive clicks for another mode.
When 18650 drained out
For example in Ni mode, press up (+) or down (-) button to set the desired temperature of the coil. Temperature range from 100℃ to 315℃ and then 200℉ to 600℉
check spring loaded connection or atomizer
Display the resistance value and wattagesetting. At standby mode, vottage = 0.00V.Once press the fire button, it will display corresponding voltage irrespective of coil temperature.
Poor connection of spring load or atomizer is worn-out.
This prevents accidental pressing on fire button
When the battery is switched on, press fire button 5 times within 2 seconds.
Check Atomizer
Temp High
Check Battery LOW POWER
LOW ATOMIZER
TIME OUT
ATOMIZER SHORT
Check Atomizer
Low Resistance
Customized mode: Set byconnecting to PC
Apart from Ni, Ti, SS, there is customized TC mode available for more choice.
Check Battery
0.15Ω80.0W 500
Ni
F
0.15Ω80.0W 500
Ni
F
0.15Ω80.0W M1
Ni
F
0.49Ω0.00V 80.0w
0.15Ω80.0W 500
SS
F
0.5Ω0.00V 80.0w
0.5Ω0.00V80.0w
0.15Ω80.0W 500
Ti
F
0.15Ω80.0W 500
TC
F
Warnings:
1. Do not charge the device outdoors or near water.
2. Do not use this device for anything other than vaping.
3. Disassemble the device will invalidate your warranty.
4. Do not swallow the e-liquid.
5. Do not look into the drip tip while vaping to prevent
juice from spitting in your eyes.
6. Do not use the device while driving.
7. Do not dispose battery to fire or use it in extreme
temperature.
8. This is not designed to be a smoking cessation device.
9. Keep all components away from children and pets.
10. Suitable temperature in using is 5-45 degree.
11. Use the provided tank and battery as a kit and do not
use with other tank or battery separately.
12. This device is designed for adults. It should not be
used by children under the age of their local smoking
or vaping laws, women who are pregnant, or those
suffering from illness that could be worsened by the
use of this product.
13. Switch off the device when putting into your pocket to
prevent accidental firing.
14. If you have an adverse reaction in the use of this
product, stop using it immediately and seek medical
assistance.
15. This device contains no user serviceable parts. It
should be repaired by qualified person only.
16. Kanger takes no responsibility for damage to person or
property through improper use of this product.
17. Kanger will not warrant this product due to improper
use or damage caused by the user.
18. KangerTech will not be responsible for any damages
or injuries caused by using a substandard battery.
End users must certify their batteries before plugging
them into a KangerTech device.
Assembly diagram
Fire button
Battery cover
Pyrex glass
Second connector
OLED
Drip tip
CLOCC
Tip and coilconnector
CUPTI 2, integrated 5mL tank with dual batteries,
is powerful and durable to operate. The child lock
system can prevent accidental opening. CUPTI 2
can output maximum 80W with TC mode. Users
can choose the standard CLOCC and CLRBA, with
adjustable air flow to achieve their best vaping
experience.
Strong Pyrex glassEnhanced Air Flow ValveReplaceable 18650 Li-cell X 2 (Discharge 30A above)Child lock system
CUPTI 2 can be adjusted by software, for more details,
please visit Kangertech’s official webpage:
www.KangerTech.com
Remarks1. To open/close the top cover, make sure the indication
icons match.
2.Ensure to prime the new coil before vaping.
3.Do not fill the tank over the Maximum juice level.
4.Switch off the device before putting into your bag or
in transit.
5.This device is can be adjusted by software.
6.The information contained in this manual is subject
to change without notice.
Cautions:
1. It has top filling, top disassembly, and top air flow (Its
size can be adjusted by twisting child-lock). Stop filling
when e-liquid comes to "MAX" line, or it may spill when
air flow base is twisted. Please twist the base down
when disassembling, then twist the coil down for the
new one.
2. It has child-lock, when "▽" on child-lock ring matches
with "|" on the base, press the child-lock and twist air
flow base, it can then be disassembled.
3. When 2 batteries have different voltages, the indicator
is subject to the lower value with "!".
Wattage “+”
Wattage “-”
Firmware
1. Download the driver software form KangerTech website:
http://www.KangerTech.com/Firmware/
2. Connect your device to your PC. The driver will
detect your device automatically.
3. Enter function interface, you can customize the
coefficient that best fits you.
4. If it failed during updating, please reconnect your
device to PC.
Note:
1. M1-M5/TC needs to be adjusted by software on PC.
2. M1-M5: Reset can change resistance temperature,
vaping time.
3. TC: Adjust the resistance coefficient.
CUPTI 2
NEWCOIL
YES+NO-