canberra b(i)8 s.a. eduard
TRANSCRIPT
Canberra B(I)8 S.A.73 3531/72 scale detail set for AIRFIX kit • sada detailù pro model 1/72 AIRFIX
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM
1/7 73 353
8,3mm
8A
9A (12A)
FOR BOTH SEATS
7A, 8A, 9A, 10A
7A, 8A, 9A, 10A
FOR BOTH SEATS
11A
28
33
29
13
11
11
13
4
2327
26
32
5
2/7 73 353
7A, 8A, 9A, 10A7A, 8A, 9A, 10A
FOR BOTH SEATS
FOR BOTH SEATS
7A, 8A, 9A, 10A
7A, 8A, 9A, 10A
for pilot`s seat
only
2
28
29
26
27
2
1
1
12 24
30
37
35
15
1631
34
3/7
?
34,6mm
29A
front
front
73 353
14A
14A
14A
14A
3B
3B
4B
19A
15A
16A
16A
7
6
70
71
52
74
14
20
10
4/7
plastic
73 353
16A
14A
2B 1B
0,5x1,0mm
18A
338
39
17
8
22
36
409
2519
187
79
50
1C
41
42
2C
5/7 73 353
6E 3E
4E, 5E
13B 14B
25A, 28A
26A, 27A
14B 13B
12B
11B
9E
9E
1E, 2E
9E
2C
2C
75
66
66
73
73
76
76
47
47
59
59
69
78 77
78 77
60 62
49
48
61
61
9E
6/7 73 353
18B
plastic
0,3mmwire0,3mm
17B
16B
15B
20B 19B
2G
2G
65 63
67 57
44 43
55
56
45
54
72
7251
58 64
46
21
7/7 73 353
fill
3pcs
4pcs
21A, 22A
23A 24A
4pcs
21B, 23B
22B, 24B
© EDUARD M.A. 2009 Made in Czech Republicwww.eduard.com
53
68
68
68
68
68
27E 28E
Canberra B(I)8 S.A.1/72 scale detail set for AIRFIX kit • sada detailù pro model 1/72 AIRFIX
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
?