card caddy

7/21/2019 Card Caddy

1/7

Card Caddy Organizer Page 1 of 7

Shannon Hebertwww.northerngirlstamper.blogspot.com

Card Caddy OrganizerBy Shannon Hebert

http://northerngirlstamper-shannon.blogspot.com

Supplies: Tools, Dies, Templates

Stampin Up Wide Punch 1 & 1 circle scallop punches

Square Nestabilities

Glue Dots

Dimensionals

Stamps

Stampin UpDelight in Life

Card stock

(3) 12 x 12 Black Card Stock will create 1box

(1) Vanilla Card Stock

Printed Paper or Card Stock

CTMH 1 er caddy

Ink

Stampin Up Basic Black

Embellishments

Heart Buttons Brads

Ribbon

Tips

FOLD ALL SCORE LINES FRONT AND BACK. THIS HELPS IN THE

CONSTRUCTION OF CADDIES


2/7



Instructions:1. Cut (1) from Black 9 X 12 for the back piece.2. Starting on the short way score @ 6.

3. Turn and score @ 3 on both ends.

4.You will now cut the slits at the bottom of the scores(3 section lines).

5. To create the angles for the sides you will measuredown the long end edge with a ruler 1 andplacea small dot for cutting placement.

6. Do this on both edges.7. Place on the cutter to cut the edges at an angle.


3/7



8. Place the upper corner edge and the dotted end onthe cutter and cut the angle.

9. Do this for both top sides.

10.Now you will adhere the bottom to create the backpiece.

11.Adhere the two sides first and then the bottom will beon the inside of the bottom back piece.

12.Set the back piece aside for now.13.To create the front piece cut (1) from Black Card

Stock 8 x 12.14.Score @ 3 on the 8 length.15.Turn and score @ 3 on both ends on the 12

length.


4/7



16.Cut out the two shorter bottom corner squares.

17.Place each top end on the cutter and cut at an angletop corner to bottom opposite corner.

18.Fold on score lines to create the front.19.With the Wide Oval Stampin Up Punch, punch the top

center of the center square. (I measured 1 from both

ends of score lines and placed a dot for placement ofthe punch center).


5/7



20.Adhere the front panel to the bottom back piece onthe outside and the sides to the inside of the backpiece.

21.To create the back height incert you will cut a piecefrom Black Card stock 4 x 4 .

22.Turn on the 4 length score @ 3/8, 7/8, 2 5/8, & 31/8.

23.Fold on all score lines and construct step.

24.For the permanent divider cut a piece from Black CardStock 5 x 3 3/4 .

25.Score from both ends on the 5 length on eachend.

26.Adhere the height step to the bottom of the divider.


6/7



27.Adhere to the inside of the Caddy being sure that theheight step is up against the back panel. Adhere tothe sides.

28.Your caddy is now complete.

The following measurements are for the printedpaper.

Cut from Vanilla Card Stock(1)4 x 4 for front(1)4 x 5 for back

(2)

3 5/8 x 5 for sides. You will measure down 1 inches on the ends again to get the angle cut.(Remember when you are doing prints you willneed to cut one on the opposite side)

Cut from Printed Paper(1)

4 1/8 x 4 1/8 for front(1) 4 1/8 x 5 5/8 for back(2)3 x 5 5/8 for sides. You will measure down 1

inches on the ends again to get the angle cut.(Remember when you are doing prints you willneed to cut one on the opposite side).


7/7



Base for Caddy29.Cut (1) from Black Card Stock 9 x 1130.Score all 4 sides @ 7/8.

31.Cut slits (red lines) and adhere to sides to formbottom base.

32.Cut (24) from Black Card Stock @ 4 7/16 x 5 forthe dividers.

33.Print the categories.34.With the 1 punch, you will punch out allthe

categories.

35.Adhere the Categories to the black scallop with adimensional.

36.Adhere the category to the divider.

37.Adhere the button to the center with a glue dot.

DECORATE AS YOU DESIRE ENJOY!!!!!

card caddy

Documents