catalog actuator damper honey well - beeteco.com

Contents3

4

6

18

Overview - Actuators

Product Selection Actuators

Non-Spring return Damper Actuators 5Nm, 10Nm, 20Nm, 34Nm

Spring return Damper Actuators 5Nm, 10Nm, 20Nm

22Fire and Smoke Damper Actuators

Overview - Actuators

Damper actuator advantage

High reliability

Accurate runtime

Same rating torque,actual output torquehigher

Easy wiring

Feature

MCU control, no limitswitchneeded

Motor overheated isprevented;Product servicelife long

The motor speed isreal-time adjusted

Actual output torqueis 1.3 timesthe rating one

Actuator and wiringbox are separate, and terminal blockis incorporatedin wiring box

Function

Accurate positioningcontrol, runtime not varied with load

Smaller-sized actuator is equivalentto the bigger onefrom competitor’s

Saving wiring time No insulation tapeneeded

Benefit

Non Spring Return(CN series)

Fire and Smoke Damper Actuator(MS Series)

Spring Return(CS series)

5NmCN4605CN6105CN7505

10NmCN4610CN6110CN7510

20NmCN4620CN6120CN7220

34NmCN4634CN6134CN7234

5NmCS4105CS7505CS8105

10NmCS4110CS7510CS8110

20NmCS4120CS7520CS8120

510

0

Spring return direct coupled actuators(DCA) for on/off damper control. Theactuator accepts an on/off signalfrom a single-pole, singlethrow(SPST) controller. They are designedto operate reliably in smoke controlsystems requiring UnderwritersLaboratories Inc. UL555S ratings upto 350 F.

3

Product Selection - Actuators

4

NON - SPRING RETURN Power Supply Control Input/Output Price List

Number(without whips)

RunningTime

(50Hz)

24 VAC/DC

220 VAC

On/Off Two

positionFloating 0/2-10 VDC

Modulating

Feedback(0/2-10 VDC)

SPDT Auxiliary Switches

(USD)

CN05 Series (5 Nm, 44 lb-in)CN4605A1001 110 • • 0 148.64

CN4605A1201 110 • • 2 (*)

CN4605A2001 110 • • • 0 (*)

CN4605A2201 110 • • • 2 (*)

CN6105A1011 90 • • • 0 153.91

CN6105A1201 90 • • • 2 (*)

CN6105A2001 90 • • • • 0 (*)

CN6105A2201 90 • • • • 2 (*)

CN7505A1001 110 • • • • 0 (*)

CN7505A1201 110 • • • • 2 (*)

CN7505A2001 110 • • • • • 0 166.37

CN7505A2201 110 • • • • • 2 (*)


CN4610A1201 110 • • 2 (*)

CN4610A2001 110 • • • 0 (*)

CN4610A2201 110 • • • 2 (*)

CN6110A1003 90 • • • 0 159.41

CN6110A1201 90 • • • 2 239.68

CN6110A2001 90 • • • • 0 (*)

CN6110A2201 90 • • • • 2 (*)

CN7510A1001 110 • • • • 0 (*)

CN7510A1201 110 • • • • 2 (*)

CN7510A2001 110 • • • • • 0 (*)

CN7510A2201 110 • • • • • 2 (*)

CN20 Series (20 Nm, 177 lb-in)CN4620A1007 110 • • 0 (*)

CN4620A1207 110 • • 2 (*)

CN4620A2007 110 • • • 0 (*)

CN4620A2207 110 • • • 2 (*)

CN6120A1006 110 • • • 0 301.98

CN6120A1207 110 • • • 2 (*)

CN6120A2007 110 • • • • 0 (*)

CN6120A2207 110 • • • • 2 (*)

CN7220A1007 110 • • • • 0 (*)

CN7220A1207 110 • • • • 2 (*)

CN7220A2007 110 • • • • • 0 353.74

CN7220A2207 110 • • • • • 2 (*)


CN4634A1208 110 • • 2 (*)

CN4634A2008 110 • • • 0 (*)

CN4634A2208 110 • • • 2 (*)

CN6134A1003 110 • • • 0 401.01

CN6134A1208 110 • • • 2 (*)

CN6134A2008 110 • • • • 0 (*)

CN6134A2208 110 • • • • 2 (*)

CN7234A1008 110 • • • • 0 (*)

CN7234A1208 110 • • • • 2 (*)

CN7234A2008 110 • • • • • 0 390.71

CN7234A2208 110 • • • • • 2 (*)

CN46

CN46

CN61

CN61

CN61

CN61

CN75

CN75

Product Selection - ActuatorsSPRING RETURN Running Time Power

Supply Control Input/Output Auxiliary Knob Price List

Number (without whips)

Drive(sec)

SpringReturn (sec)

24 VAC/DC

100-250VAC

On/Off Two

position

Modulating and Floating

Feedback(0/2-10VDC)


(USD)

CS05 Series (5 Nm, 44 lb-in)CS4105A1002 90 <20 • • 0 305.28

CS4105A1102 90 <20 • • 0 (*)

CS8105A1008 90 <20 • • 0 276.34

CS8105A1102 90 <20 • • 0 (*)

CS7505A2008 90 <20 • • 0 334.09

CS7505A2202 90 <20 • • • 2 (*)

CS10 Series (10 Nm, 88 lb-in)

CS4110A1002 90 <20 • • 0 302.01

CS4110A1200 90 <20 • • 0 396.06

CS8110A1008 90 <20 • • 0 272.56

CS8110A1206 90 <20 • • 0 363.01

CS7510A2008 90 <20 • • 0 357.75

CS7510A2206 90 <20 • • • 2 416.26

CS20 Series (20 Nm, 175 lb-in)

CS4120A1001 90 <20 • • 0 318.63

CS4120A1209 90 <20 • • 0 414.69

CS8120A1007 90 <20 • • 0 286.83

CS8120A1205 90 <20 • • 0 381.19

CS7520A2007 90 <20 • • 0 356.09

CS7520A2205 90 <20 • • • 2 439.81

FIRE AND SMOKE SPRING RETURN

Running Time Power Supply Control Input/Output Auxiliary Knob Price List

Fast acting, two position spring return. Rating up to 350oF

Number(without whips)

Drive(sec)

Spring Return (sec)

24 VAC 120VAC

230VAC

On/ Off Two position

Feedback(0/2-10 VDC)


(USD)

MS04 Series (4 Nm, 44 lb-in)MS4104F1010 15 <15 • • 0 (*)

MS4104F1210 15 <15 • • 2 (*)

MS4604F1010 15 <15 • • 0 (*)

MS4604F1210 15 <15 • • 2 (*)

MS8104F1010 15 <15 • • 0 (*)

MS8104F1210 15 <15 • • 2 (*)

MS09 Series (9 Nm, 80 lb-in)

MS4109F1010 15 <15 • • 0 (*)

MS4109F1210 15 <15 • • 2 (*)

MS4609F1010 15 <15 • • 0 523.50

MS4609F1210 15 <15 • • 2 257.50

MS8109F1010 15 <15 • • 0 (*)

MS8109F1210 15 <15 • • 2 (*)

M

M

M

M

M

M

CS7

CS1

CS4

CS4

CS8

CS8

CS7

CS7

CN05, CN10 SERIES NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR FLOATING AND TWO-POSITION CONTROL

PRODUCT DATA

GENERAL This non-spring return direct-coupled damper actuator provides floating and two-position control for: • air dampers,• VAV units,• air handlers,• ventilation flaps,• louvers, and• reliable control for air damper applications with up to 10

sq ft / 44 lb-in. (5 Nm) and 20 sq ft / 88 lb-in. (10 Nm)(seal- less damper blades; air friction-dependent).

FEATURES • Declutch for manual adjustment• Adjustable mechanical end limits• Removable access cover for direct wiring• Mountable in any orientation• Rotation direction and service/OFF switch

SPECIFICATIONSSupply voltageCN6105/CN6110 24 Vac/dc -15%/+20%, 50/60 Hz CN4605/CN4610 230 Vac -15%/+20%, 50/60 Hz Nominal voltageCN6105/CN6110 24 Vac/dc, 50/60 Hz CN4605/CN4610 230Vac, 50/60 Hz All values stated hereinafter apply to operation under nominal voltage conditions.Power consumptionCN6105/CN6110 5 VA / 2 W CN4605 22 VA / 2 W at 50 Hz CN4610 25 VA / 2 W at 60 Hz Ambient limitsAmbient operating limits -5...+140 °F (20...+60 °C) Ambient storage limits -22...+176 °F (-30...+80 °C) Relative humidity 5...95%, non-condensing SafetyProtection standard IP54 Protection class II as per EN 60730-1 Overvoltage category II LifetimeFull strokes 60000 Repositions 1.5 million MountingRound damper shaft 3/8 in…5/8 in. Square damper shaft 1/4 in…1/2 in.; 45° steps Shaft length min. 1-5/8 in. End switches (when included)Rating Class II Triggering points 5° / 85° Torque rating 44 lb-in. (5Nm) / 88 lb-in. (10 Nm) Runtime for 90°CN6105 90 sec (dc / 60 Hz ac) CN6110 90 sec (dc / 50 Hz ac) CN4605 65…110 s (60/50 Hz) CN4610 65…140 s (60/50 Hz) Rotation stroke 95° + 3° Dimensions see “Dimensions” on page 11 Weight (without cables) 1 lbs. Noise rating 35 dB(A) max. at 1 m

40 dB(A) for 230 Vac at 65 sec runtime

Certification CN6105/CN6110 CE & UL CN4605/CN4610 CE

C

6

PRODUCT IDENTIFICATION SYSTEM

C-Electrical Motor N-Fail Safe Function (Non-Spring Return)

61-24V Floating Control + ON/OFF 75-24V Modulating Control + Floating + ON/OFF 46-230V ON/OFF

05-44 lb-in. (5 Nm) 10-88 lb-in. (10 Nm)

A-Standard Model 1-No Feedback 2-Voltage Feedback Signal

0-No Internal Auxiliary Switches 2-Two Internal Auxiliary Switches

XX-System Controlled Numbers

C N 75 10 A 2 0 XX

BASIC FEATURES

Fig. 1. Setting units and control elements

Legend for Fig. 1: 1) Universal shaft adapter2) Mechanical end limits (manually adjustable)3) Declutch button4) Function selection switch5) Removable access cover6) Anti-rotation bracket

Contents of Package The delivery package includes the actuator, parts 1 through 6 (see Fig. 1), plus two cable grommets and a spare cable grommet.

RUN MODES The function selection switch (see Fig. 2) can be used to place the actuator into any one of two different modes:

• Service/Off; or• the floating/2-position run mode (“Dir” for CCW-closing

dampers or “Rev” for CW-closing dampers).

Fig. 2. Function selection switch

Power-Off Behavior If power is removed, the shaft adapter remains in position.

Service/Off If the function selection switch is set to the “Service/Off” position, then all rotary movement is cancelled, and all control signals are ignored, thus allowing the actuator to be manually operated safely.

Model Description

CN6105A1011 5Nm, 24Vac/Vdc, floating control, non-spring return, no feedback and without aux. Switch

CN4605A1001 5Nm, 230Vac, floating control, non-spring

return, no feedback and without aux. Switch

CN6110A100310Nm, 24Vac/Vdc, floating control, non-spring return, no feedback and without aux. Switch

CN6110A120110Nm, 24Vac/Vdc, floating control, non-spring

return, no feedback and with aux. Switch

CN4610A100110Nm, 230Vac, floating control, non-spring return, no feedback and without aux. Switch

CN05,CN10 SERIES DAMPER ACTUATORS FOR FLOATING/2-POSITON CONTROL

7

Floating/2-Position Run Mode If the function selection switch has been set to one of the two floating/2-position control settings—and if the actuator is wired correspondingly (see Fig. 7, Fig. 8, and Fig. 9)—then as soon as operating power is applied, the shaft adapter will run according to the control signals applied.

Table 1 describes the behavior (“stops,” rotates “CCW,” or rotates “CW”) of the CN6105/CN6110 in dependence upon the control signals (switch “open” or “24 Vac/dc”) applied to terminals 3 and 4, the function selection switch setting, and the manner in which the actuator is wired (either for floating mode: see Fig. 7; or for 2-position mode: see Fig. 8).

Table 1. Behavior of CN6105/CN6110

wiring control signal at switch setting term 3 term 4 Dir Service/ Off Rev

float. open open stops stops stopsopen 24Vac/dc CCW stops CW

24Vac/dc open CW stops CCW2-pos. 24Vac/dc open CW stops CCW

24Vac/dc 24Vac/dc CCW stops CW

Table 2 describes the behavior (“stops,” rotates “CCW,” or rotates “CW”) of the CN4605/CN4610 in dependence upon the control signals (switch “open” or “230 Vac”) applied to terminals 1 and 3 and the function selection switch setting: only one manner of wiring is permitted (see Fig. 9).

Table 2. Behavior of CN4605/CN4610

control signal at switch setting term 1 term 3 Dir Service/ Off Rev

open open stops stops stops open 230 Vac stops stops stops

230 Vac open CW stops CCW 230 Vac 230 Vac CCW stops CW

MANUAL ADJUSTMENT IMPORTANT

To prevent equipment damage, before manual adjustment, you must remove power or set the func-tion selection switch to the “Service/Off” position.

After removing power or setting the function selection switch to the “Service/Off” position, the gear train can be disengaged using the declutch button, permitting the shaft adapter to be manually rotated to any position.

Limitation of Rotation Stroke Two adjustable mechanical end limits are provided to limit the angle of rotation as desired (see Fig. 3). The mechanical end limits must be securely fastened in place.

Fig.3. Mechanical end limits

To ensure tight closing of the dampers, the shaft adapter has a total rotation stroke of 95°.

INTERNAL END SWITCHES The internal end switches “A” and “B” are changeover switches which are activated when the shaft adapter moves past a position of 5° and 85°, respectively (see also Table 5).

Fig.4. Internal end switch triggering points


8


9

INSTALLATION To avoid personal injury (electrical shock) and to prevent equipment damage, before installation, you must remove power.

These actuators are designed for single-point mounting.

Mounting Instructions All information and steps are included in the Installation Instructions supplied with each actuator.

Mounting Position The actuators can be mounted in any position (IP54 is dependent upon orientation; see Fig. 5). Choose a mounting pKosition permitting easy access to cables and controls.

Fig. 5. Mounting for IP54

NOTE: Further, in order to guarantee IP54, only original Honeywell grommets may be used.

Anti-Rotation Bracket and Screws If the actuator is to be mounted directly on a damper shaft, use the anti-rotation bracket and screws included in the delivery package. The min. distance between the center of the damper shaft and the middle of the anti-rotation bracket is 3.35 in.; a max. of 4.25 in. is allowed (see also Fig 11).

Depending upon the specifics of your mounting site, the actuator may shift in position slightly while tightening the screws at the top of the shaft adapter. The anti-rotation bracket features a T-piece with a 5-mm-long shank to accommodate for this movement. It is important to ensure that this play is not impeded.

Universal Shaft Adapter The universal shaft adapter can be used for shafts of various diameters and shapes (round: 3/8...5/8 in. and square: 1/4...1/2 in.).

WIRING

To avoid personal injury (electrical shock) and to prevent equipment damage, before wiring, you must remove power.

Access Cover IMPORTANT

Once the access cover has been removed, please take care to avoid damaging any of the parts now accessible.

The access cover can be unscrewed and removed in order to gain access to the terminal block(s) and perform wiring.

Fig. 6. Access Cover

Wiring Diagrams

Fig. 7. CN6105/CN6110 (floating mode)

! CAUTION

Fig. 8. CN6105/CN6110 (2-position mode)

CCW

CW

230V~

3

1

2

5

4NL

230V ~

> 3 mm!

Fig. 9. CN4605/CN4610 (2-position mode)

Fig. 10. End switches

NOTE: Both internal end switches must be connected to the same power source.

Tables 3,4 and 5 summarize the information presented in the preceding wiring diagrams.

Table 3. Signals at terminals for CN6105/CN6110 ter-

minal signal in floating signal in 2-pos. mode

2 common ~/- common ~/- 3 24 V ~/+

(control signal) 24 V ~/+

(control/ power signal) 4 24 V ~/+

(control signal) 24 V ~/+

(control signal/power) NOTE: All cables connected to these terminals must be

equipped with spark suppression.

Table 4. Signals at terminals for CN4605/CN4610 terminal signal

1 L (230 V ~) 2 N (230 V ~) 3 control signal

NOTE: All cables connected to these terminals must be equipped with spark suppression.

Table 5. Internal end switches (SSW2) terminal type of switch

S1 common lead for switches A and B

S2 / S3 change-over switch A (S1/S2 opens and S1/S3 closes when shaft adapter moves CW past 5°; reverts to original state when shaft adapter moves CCW past 5°).

S5 / S6 change-over switch B (S1/S5 opens and S1/S6 closes when shaft adapter moves CW past 85°; reverts to original state when shaft adapter moves CCW past 85°).


10

DIMENSIONS

Fig. 11. Dimensions (in in.)


11

CN20, CN34 SERIES NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORSFOR FLOATING / 2-POSITION CONTROL

PRODUCT DATA

GENERALThese direct-coupled damper actuators provide two-position and floating control for:

air dampers,VAV units,air handlers,ventilation flaps,louvers, andreliable control for air damper applications with up to4.6 m2 / 50 sq.ft. (20 Nm / 177 lb-in) or 7.8 m2 / 85 sq. ft.(34 Nm / 300 lb-in) (seal-less dampers; air friction-dependent).

FEATURESSelf-centering shaft adapterAccess cover to facilitate connectivityService/off for safe & easy servicingRotation direction selectable by switchDeclutch for manual adjustmentMechanical end limitsField-installable auxiliary switchesMountable in any orientation (no IP54 if upside down)Mechanical position indicatorCE and UL certified (230V models with CE only)

SPECIFICATIONSSupply voltage CN6120/CN6134 24 Vac/dc 15%, 50/60 Hz CN4620/CN4634 230 Vac 15%, 50/60 Hz Nominal voltage CN6120/CN6134 24 Vac/dc, 50/60 Hz CN4620/CN4634 230 Vac, 50/60 Hz All values stated hereinafter apply to operation under nominal voltage conditions. Power consumption CN6120 6 VA / 3 W CN4620 8 VA / 3 W CN6134 6 VA / 3 W CN4634 10 VA / 4 W Ambient limits Ambient operating limits -20...+60 C (-5...+140 °F) Ambient storage limits -40...+80 C (-40...+175 °F) Relative humidity 5...95%, non-condensing Safety Protection standard IP54 as per EN 60529 Protection class II as per EN 60730-1 Overvoltage category III LifetimeFull strokes 60000 Repositions 1.5 million MountingRound damper shaft 10...27 mm (3/8...1-1/16") Square damper shaft 10...18 mm (3/8...11/16");

spets °54Shaft length min. 22 mm (7/8") End switches (when included) Rating 5 A (resistive) / 3 A (inductive) Triggering points 5 / 85 Torque rating CN6120 / CN4620 20 Nm (177 lb-in) CN6134 / CN4634 34 Nm (300 lb-in) Runtime 95 sec (60 Hz) / 110 sec (50 Hz

or DC supply) Rotation stroke 95 3 Dimensions see "Dimensions" on page 17 Weight (without cables) 1.35 kg (3 lbs.) Noise rating 40 dBA max. at 1 m Certification CE CN6120 / CN6134

CN4620 / CN4634 UL CN6120 / CN6134

12

C

CN20, CN34 SERIES DAMPER ACTUATOR FOR FLOATING AND 2-POS CONTROL

MODELS Description # Model

CN6120A1002 20Nm,24Vac/Vdc, Floating/2-position control, Non-Spring Return, No feedback and without aux. Switch CN4620A1001 20Nm,230V,Floating/2-position control, Non-Spring Return, No feedback and without aux. Switch CN6134A1003 34Nm,24Vac/Vdc, Floating/2-position control, Non-Spring Return, No feedback and without aux. Switch CN4634A1001 34Nm,230Vac, Floating control/2-position, Non-Spring Return, No feedback and without aux. Switch

Product Identification System C – Direct Coupled Actuator

N – Fail Safe Function (Non-Spring Return) 61 – 24V Floating/2-position Control 72 – 24V Modulating and Floating/2-position Control 46 – 230V Floating/2-position Control

20 – 20 Nm (177 lb-in) 34 – 34 Nm (300 lb-in)

A – Standard Model 1 – No Feedback 2 – Voltage Feedback Signal

0 – No Internal Auxiliary Switches 2 – Two Internal Auxiliary Switches

XX – System Controlled Numbers

C N 61 20 A 1 0 XX

Fig. 1. Product Identification System

OPERATION / FUNCTIONS

Fig. 2. Setting units and control elements

Legend for Fig. 2: 1 Self-centering shaft adapter 2 Retainer clip 3 Rotational angle scales (0...90° / 90...0°) 4 Mechanical end limits 5 Declutch button 6 Anti-rotation bracket 7 Function selection switch 8 Access cover

Contents of Package The delivery package includes the actuator itself, parts 1 through 8 (see Fig.2), the anti-rotation bracket screws, and installation instruction.

RUN MODES The function selection switch (see Fig. 3) can be used to place the actuator into any one of three different modes:

Dir, floating/2-position control, cw run.Service/Off, actuator stop running.Rev, floating/2-position control, ccw run.

1

2

3

4

5 6

8 7

13


Fig. 3. Function selection switch

Power-Off Behavior If power is removed, the actuator retains its position.

Service/OffIf the function selection switch is set to the "Service/Off" position, all rotary movement is cancelled, and all control signals are ignored, thus allowing the actuator to be safely manually operated.

Floating/2-Position Run Mode If the function selection switch has been set to one of the two floating/2-position control settings (Dir or Rev) and the actuator is wired correspondingly (see A1 and A2) as soon as the operating power is applied, the actuator will run according to the power applied

Table 1 describes the behavior (stops, rotates CCW, or rotates CW) of the CN6120/CN6134 in relation to the control signals (switch "open" or "24Vac/dc") applied to terminals 3 and 4, the function selection switch setting, and the manner in which the actuator is wired (either for floating mode: see A1, or for 2-position mode: see A2).

Table 1. Behavior of CN6120/CN6134 Control signal at Function selection switchWiring term. 3 term. 4 Dir Service/Off Rev open open stops stops stops open 24Vac/dc CCW stops CW Float.

24Vac/dc open CW stops CCW 24Vac/dc open CW stops CCW 2-pos. 24Vac/dc 24Vac/dc CCW stops CW

Table 2 shows the same actuator behavior as Table 1, but for CN4620/CN4634 (230Vac models).

Table 2. Behavior of CN4620/CN4634 Control signal at Function selection switch Wiring term. 3 term. 4 Dir Service/Off Rev open open stops stops stops open 230Vac CCW stops CW Float.

230Vac open CW stops CCW 230Vac open CW stops CCW 2-pos. 230Vac 230Vac CCW stops CW

Sleep Mode When actuator reaches end stop or any obstacles blocking its running, it will fall into sleep mode automatically. Actuator will

periodically start up and try to resume running, which will save energy significantly through whole service life.

Position Indication The hub adapter indicates the rotation angle position by means of the rotational angle scales (0...90° / 90...0°) provided in the actuator plate (see Fig. 4).

Fig. 4. Position indication

Manual Adjustment

IMPORTANTTo prevent equipment damage, you must remove power or set the rotation direction switch to the "Service/Off" position before manual adjustment.

After removing power or setting the rotation direction switch to the "Service/Off" position, the gear train can be disengaged using the declutch button, permitting the actuator shaft to be manually rotated to any position.

Limitation of Rotation Stroke Two adjustable mechanical end limits (adjustable in 5° increments) are provided to limit the angle of rotation as desired (see Fig. 5).

Fig. 5. Mechanical end limits

The mechanical end limits must be securely fastened in place. It is important that they properly mesh with the rotational angle scales when the screws are tightened.

Internal End Switches NOTE: Applicable to models with internal switches only.

14

!


The internal end switches are set to switch from "common" to "normally open" at angles of 5° and 85°, respectively, from the totally counterclockwise position.

-2.5

85 80 5 590 092.5 51015

CCW internalend switch

CW internalend switch

actuator scale: clockwise

end switch scale

actuator scale: counterclockwise

Fig. 6. Internal end switch triggering points

INSTALLATIONThese actuators are designed for single-point mounting.

In order to prevent equipment damage, you must remove power or set the rotation direction switch to the "Service/Off" position before manual operation.

Mounting Instructions All information and steps are included in the installation instructions supplied with the actuator.

Mounting Position The actuators can be mounted in any position (no IP54 if mounted upside down; see Fig. 7). Choose a mounting posi-tion permitting easy access to the actuator's cables and controls.

IP54 IP54IP54 IP54

Fig. 7. Mounting for IP54

Mounting Bracket and Screws If the actuator is to be mounted directly on a damper shaft, use the mounting bracket and screws included in the delivery package.

Self-Centering Shaft Adapter The self-centering shaft adapter can be used for shafts having various diameters (10...27 mm [3/8...1-1/16"]) and shapes (square or round).

In the case of short shafts, the shaft adapter may be reversed and mounted on the duct side.

Stroke Limitation with Mechanical End Limits The mechanical end limits enable the stroke to be limited from 0...90° in increments of 5°.

WiringConnecting to the Power Supply In order to comply with protection class II, the power source of 24 V actuators must be reliably separated from the network power supply circuits as per DIN VDE 0106, part 101.

Access Cover To facilitate wiring the actuator to the controller, the access cover can be detached from the actuator.

Remove power before detaching the access cover. Once the access cover has been removed, please take care to avoid damaging any of the parts now accessible.

Fig. 8. Access cover (models with internal switches)

Depending upon the model, the access cover may have one or two terminal strips, including a layout with a description for each of the terminals.

Fig. 9. Actuator with access cover removed (models with internal switches)

15

IMPORTANT! IMPORTANT!


Wiring diagrams A1 CN6120,CN4620CN6134,CN4634 FLOATING

A2 CN6120,CN4620CN6134,CN4634 2-POS

A3 END SWITCHS(models with switch only)

NOTE: Internal end switches S1 and S4 must be connected to the same power source. Below 2 tables summarize the information presented in the preceding wiring diagrams.

WiringModels Terminal Floating 2-position

2 common / common / 3 24V ~/+ (clockwise) 24V ~/+

CN6120,CN6134 supply and signal lines

(must be equipped with spark suppressors) 4 24V ~/+ (counterclockwise) 24V ~/+ control signal 2 common / common / 3 230Vac (clockwise) 230Vac

CN4620,CN4634 supply and signal lines

(must be equipped with spark suppressors) 4 230Vac (counterclockwise) 230Vac control signal

Connecting cable Terminal Description S1 common S2 normally closed CCW (left) 5° S3 normally open S4 common S5 normally closed

end switches (models with internal

switches only) CW (right) 85° S6 normally open

OPTIONAL ACCESSORIES The following optional accessories can be ordered separately.

Auxiliary Switch Kit Order no.: SW2

S1S2

S3AB

S4S5

S6 CD45

090

900

A

B

C

D

The auxiliary switches are field-installable parts providing two SPDT freely-adjustable switches.

SPARE PARTS Spare Parts Kit Order no.: A7209.2071 The spare parts kit contains the following items:

Anti-rotation bracket and screwsAccess cover screwPlastic protective cap for protection standard IP54Mechanical end limit screw and retainer

Anti-Rotation Bracket Kit Order no.: A7209.2073 The anti-rotation bracket kit can be ordered separately.

Contains: 10 anti-rotation brackets20 screws

16


DIMENSIONS

17

CS05, CS10, CS20 Series Spring Return Direct Coupled ActuatorsCS4105, CS4110, CS4120, CS7505, CS7510, CS7520, CS8105,CS8110, CS8120

PRODUCT DATA

FEATURES

APPLICATIONCS41XX, CS75XX, CS81XX Spring Return Direct CoupledActuators (DCA) are used within heating, ventilating, and air-conditioning (HVAC) systems. They can drive a variety ofquarter-turn, final control elements requiring spring return fail-safe operation.

Applications include:• Volume control dampers, mounted directly to the drive

shaft or remotely (with the use of accessory hardware).• Quarter-turn rotary valves, such as ball or butterfly valves

mounted directly to the drive shaft.• Linear stroke globe or cage valves mounted with linkages

to provide linear actuation.

• Brushless DC submotor with electronic stall protectionfor floating/modulating models.

• Brush DC submotor with electronic stall protection for2-position models.

• Self-centering shaft adapter (shaft coupling) for widerange of shaft sizes.

• Models available with three torque ratings:44 lb-in. (5 N•m), 88 lb-in. (10 N•m),and 175 lb-in. (20 N•m).

• Models available for use with two-position, single polesingle throw (spst), line-voltage or low-voltagecontrols.

• Models available for use with floating or switchedsingle-pole, double-throw (spdt) controls.

• Models available for use with proportional current orvoltage controls.

• Models available with combined floating/modulatingcontrol in a single device.

• Models available with adjustable zero and span.• Models available with line-voltage internal and

switches.• Access cover to facilitate connectivity.• Metal housing with built-in mechanical end limits.• Spring return direction field-selectable.• Shaft position indicator and scale.• Manual winding capability with locking function.• UL (cUL) listed and CE compliant.• All Models are plenum-rated per UL873.

18

C

M20952

SPECIFICATIONSModels: See Tables 2, 3 and 4.

Dimensions: See Fig. 1.

Device Weight: 7 lb (3.2 kg).

Timing (At Rated Torque and Voltage):Drive Open (typical):

Floating, Modulating Models: 90 seconds.Two-Position Models: 45 seconds ±5 seconds.

Spring Close: 20 seconds typical.

3-15/16 (100)

Temperature Ratings: 1-9/16 1-9/16

Ambient: -40°F to 140°F (-40°C to 60°C).Shipping and Storage: -40°F to 158°F (-40°C to 70°C).

Humidity Ratings: 5% to 95% RH noncondensing.

Electrical Connections:Field wiring 14 to 22 AWG (2.0 to 0.344 mm sq) to screw

terminals, located under the removable access cover.

(40) (40)

1-9/16(40)

2-1/2(64)MIN.

3(76)MIN.FROMSHAFTEND

Electrical Ratings: See Table 1.

End Switches (Two SPDT):Settings (fixed): 7° nominal stroke, 85° nominal stroke.Ratings (maximum load):

Low-Voltage Models: 250 VAC, 5A resistive, 3A inductive.Line-Voltage Models: 250 VAC, 5A resistive.

Mounting: Self-centering shaft adapter (shaft coupling).Round Damper Shafts: 0.375 to 1.06 in. (10 to 27 mm).Square Damper Shafts: 1/2 to 3/4 in. (13 to 19 mm).Actuator can be mounted with shaft in any position.

NOTE: For 175 lb-in. (20 N•m) models: 3/4 in. or greatershaft diameter recommended.

Minimum Damper Shaft Length: 1 in. (25 mm); 3 in.(76 mm) recommended.

1/4 (6)

9-3/4(247)

6-1/8(156)

3 (76)MIN.

2-15/16 (75)

Fig. 1. Dimensional drawing of actuator in in. (mm).

Table 1. Electrical Ratings.Power Input Power Consumption (VA)

44 lb-in. (5 N•m) 88 lb-in. (10 N•m) 175 lb-in. (20 N•m)Model(s) Voltage Frequency Driving Holding Driving Holding Driving Holding

Floating, Modulating 24 VAC±20% (Class 2), 24 VDC 50/60 Hz. 13 5 14 5 16 5Two-Position, Low-voltage 24 VAC±20% (Class 2), 24 VDC 50/60 Hz. 25 8 30 8 40 8Two-Position, Line-voltage 100-250 VAC 50/60 Hz. 45 13 45 13 60 13

ORDERING INFORMATIONIf you have additional questions, need further information, or would like to comment on our products or services, please write orphone:

1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory).2. Honeywell ECC Customer Care

35F., Tower A, City Center 100 Zun Yi RoadShanghai 200051 China Tel: (86-21) 5257 4568

International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Finland, France, Germany,Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, P.R.C.

19

CS05, CS10,CS20 SERIES SPRING RETURN DIRECT COUPLED ACTUATORS

Model Description

CS4105A1002 100-250 VAC Two-Position Control; Reversible Mount;5N•m; Standard U.S Model; No Feedback; No EndSwitches;


CS4110A1200 100-250 VAC Two-Position Control; Reversible Mount;10N•m; Standard U.S Model; No Feedback; Two EndSwitches;


CS4120A1209 100-250 VAC Two-Position Control; Reversible Mount;20N•m; Standard U.S Model; No Feedback; Two EndSwitches;

CS7505A2008 24 VAC/VDC Modulating and Floating Control ; ReversibleMount; 5N•m; Standard U.S Model; Voltage FeedbackSignal; No End Switches;


CS7510A2206 24 VAC/VDC Modulating and Floating Control ; ReversibleMount; 10N•m; Standard U.S Model; Voltage FeedbackSignal; Two End Switches;

CS7510H2209 24 VAC/VDC Modulating and Floating Control; ReversibleMount; 10N•m; Selectable control signal; Adjustable zeroand span; Includes service and atuo-adapt modes; VoltageFeedback Signal; Two End Switches;


CS7520A2205 24 VAC/VDC Modulating and Floating Control ; ReversibleMount; 20N•m; Standard U.S Model; Voltage FeedbackSignal; Two End Switches;

CS7520H2208 24 VAC/VDC Modulating and Floating Control; ReversibleMount; 20N•m; Selectable control signal; Adjustable zeroand span; Includes service and atuo-adapt modes; VoltageFeedback Signal; Two End Switches;

CS8105A1008 24 VAC/VDC Two-Position Control; Reversible Mount;5N•m; Standard U.S Model; No Feedback; No EndSwitches;


CS8110A1206 24 VAC/VDC Two-Position Control; Reversible Mount;10N•m; Standard U.S Model; No Feedback; Two EndSwitches;


CS8120A1205 24 VAC/VDC Two-Position Control; Reversible Mount;20N•m; Standard U.S Model; No Feedback; Two EndSwitches;

Table 2. O.S. Number Selection (see Table 3 also).C Motorized Actuator

S Fail Safe Function (Spring Return)41 100-250 VAC Two-Position Control; Reversible Mount75 24 VAC/VDC Modulating and Floating Control ; Reversible Mount81 24 VAC/VDC Two-Position Control; Reversible Mount

05 44 lb-in. (5 N•m)10 88 lb-in. (10 N•m)20 175 lb-in. (20 N•m)

Aa Standard U.S. Model

Bb Standard European Model

Eb

Ha

Selectable control signal; Adjustable zero and span;Includes service and auto-adapt modes

1 No Feedback2 Voltage Feedback Signal

0 No End Switches2 Two End Switches

X X System Controlled Numbers

C S 7a Model manufactured for sale in the United States.b Model manufactured for sale in Europe.

Table 4. Available Model

Table 3. Actuator Catalog Numbering (see Table 2 also).S Spring Return Fail Safe ModeN Non-Spring Return Fail Safe Mode

05 44 lb-in. (5 N•m); Spring Return Only10 88 lb-in. (10 N•m); Spring Return Only

20 175 lb-in. (20 N•m)34 300 lb-in. (34 N•m); Non-Spring Return Only

24 24 VAC/VDC Floating Control24-2POS 24 VAC/VDC Two-Position Control120-2POS 120 VAC Two-Position Control230-2POS 230 VAC Two-Position Control

010 24 VAC/VDC Modulating and Floating ControlFixed Zero/Span, No End Switches

-SW2 Internal End Switches

-SERa Enhanced Modulating; Adjustable Zero/Span

S 10 24-2POS -SW2a Enhanced models include two internal end switches.

20


Stroke: 95° ±3°, mechanically limited.Design Life (at Rated Voltage):Two-position models: 50,000 full stroke cycles;

50,000 full stroke spring returns.Floating and Modulating models: 60,000 full stroke cycles;

1,500,000 repositions; 60,000 full stroke spring returns.

Controller Type:S05, S10, S20: See Table 3.S05, S10, S20: Modulating or Floating; controlled by selector

switch.Input Impedance: 95K ohms minimum.Feedback Signal: 0-10 VDC or 2-10 VDC;

Driving current is 3 mA minimum.

Torque Ratings:Typical Holding, Driving, Spring Return:

S05: 44 lb-in. (5 N•m).S10: 88 lb-in. (10 N•m).S20: 175 lb-in. (20 N•m).

Stall Maximum (fully open at 24°C):S05: 100 lb-in. (11.3 N•m).S10: 200 lb-in. (22.6 N•m).S20: 350 lb-in. (39.6 N•m).

Noise Rating at 1m (Maximum):Holding: 20 dBA (no audible noise).Two-position models:

Driving: 50 dBA.Spring Return: 65 dBA.

Floating and Modulating models:Driving: 40 dBA.Spring Return: 50 dBA.

Environmental Protection Ratings:NEMA2 (US Models) or IP54 (European Models) when

mounted on a horizontal shaft with access cover below theshaft.

Approvals: See Table 5.

Table 5. Approvals.UL/cUL

UL873 Plenum Rating,File No. E4436; Guide No. XAPX.

CEC-TICK

Accessories:32004254-002 Self-Centering Shaft Adapter (supplied with

actuator).50030966-001 Anti-Rotation Bracket (supplied with actuator).6174215 Extension Screw (supplied with actuator).27518 Balljoint (5/16 in.).103598 Balljoint (1/4 in.).205860 Electronic Minimum Position Potentiometer.27520A-E,G,H-L,Q Pushrod (5/16 in. diameter).5450074 Water-tight Cable Gland/Strain-relief Fitting

(supplied with actuator).32003036-001 Weather Enclosure.50001194-001 Foot Mount Kit.50005859-001 NEMA4/4X Enclosure.SW2-US Auxiliary Switch Package.See also Form 63-2620.

SizingRequired TorqueIn lieu of data from a Specification Engineer or Manufacturer,required torque for a given damper load can be determinedusing the following method:

Where:— TR = Required torque for the damper load.— TD = Damper torque rating from the manufacturer,

expressed in either (lb-in.)/(sq ft) or (N•m)/(sq m). thedamper load.

— AD = Damper area expressed in either sq ft or sq m.

Actuators RequiredIn lieu of data from a Specification Engineer or Manufacturer,the number of required actuators for a given damper loadcan be determined using the following method:

Where:N = Number of actuators.

— TR = Required torque for the damper load. (See above.)— TA = Actuator torque rating.— SF = Safety factor.

NOTE: The safety factor accounts for variables such asmis- alignments, aging of the damper, etc. 0.8 is atypical safety factor.

T FS

TN

A

R

DDR ATT

21


PRODUCT DATA

APPLICATIONThe MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 Fast-Acting, Two-Position Actuators are spring return direct coupled actuators (DCA) with an integral junction box for on/o damper control. The actuator accepts an on/o signal from a single-pole, single-throw (spst) controller. Reversible mounting allows actuator to be used for either clockwise (cw) or counterclockwise (ccw) spring return and are designed to operate reliably in smoke control systems requiring

FEATURES• 30 lb-in. (3.4 N•m) or 80 lb-in. (9 N•m) minimum driving

torque at 350 °F (176 °C).

• Reversible mounting facilitates use in either clockwise (cw) or counterclockwise (ccw) spring rotation.

• Integral spring return ensures level of return torque.

• Stainless steel internal spring.

• Fifteen-second spring return timing.

• No special cycling required during long-term holding.

• No audible noise during holding.

• Patent pending design eliminates need for limit switches to reduce power consumption.

• Models available for 24, 120 and 230 Vac.

• N degree angle of rotation.

• Actuator holds rated torque at reduced power level.

• Die-cast aluminum housing.

• Housing design allows ush mounting to damper.

• Designed to operated reliably in smoke control systems requiring Underwriter's Laboratories Inc. UL555S rating up to 350F.

• Models available with SPST position-indicating switches (7°, 85° stroke).

Fire and Smoke Damper ActuatorMS4104, MS4109, MS4604, MS4609, MS8104, MS8109 Fast-Acting, Two-Position Actuators FOR FIRE/SMOKE CONTROL APPLICATIONS

Wiring:

Fig. 1. Typical 24 Vac wiring.


M34624

24 VAC

BLACK

RED

L1 ( )

L2 ( )

YELLOW

YELLOW

BLUE7° AUXILIARY

SWITCH

85° AUXILIARYSWITCH

BLUE

WHITE

BLACK

GREENL1 ( )

L2 ( )

YELLOW

YELLOW

BLUE

BLUE7° AUXILIARY

SWITCH


120 VAC

M34625


Dimensions:

M34626

BLUE

BROWN

GREEN

230 VAC

L1 ( )

L2 ( )

YELLOW

YELLOW

BLUE

BLUE7° AUXILIARY

SWITCH


M34622

2 (51)

1 (25)

90° 0°

11/16(17)

6-3/8(161)

8-15/16(227)

4 (102)2 (51) 1/16

(2)3-1/4 (83)

5-1/8 (130)

9/16 (14)

22N314

MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 FAST-ACTING, TWO-POSITION ACTUATORS

ModelVoltage

(Vac)

Internal Auxiliary Switches

Torquein lb-in.

(N •m)

MS4104F1010

120

120 30 (3.4)None

None

None

None

None

None

MS4104F1210 2 SPST a

2 SPSTa

2 SPSTa

2 SPSTa

2 SPSTa

2 SPSTa

30 (3.4)

120

120

320

320

80 (9)

80 (9)

30 (3.4)

30 (3.4)

320 80 (9)

320 80 (9)

24 30 (3.4)

24 30 (3.4)24 80 (9)

24 80 (9)

MS4109F1010

MS4109F1210

MS4604F1010

MS4604F1210

MS4609F1010

MS4609F1210

MS8104F1010

MS8104F1210MS8109F1010

MS8109F1210

SPECIFICATIONSModels:

a Internal switches are designed to pass UL555S requirements (at 350 °F for 30 minutes) and are intended for use as position indication.

Electrical Ratings:Power Input:

MS4104F, MS4109F: 120 Vac ±10%, 60 Hz.MS4604F, MS4609F: 230 Vac ±10%, 50/60 Hz.MS8104F, MS8109F: 24 Vac +20%, -10%, 50/60 Hz.

Power Consumption:MS4104F: Running: 0.18A, 18W. Holding: 0.11A, 9WMS4109F: Running: 0.25A, 23W. Holding: 0.13A, 7WMS4604F: Running: 0.13A, 18W. Holding: 0.10A, 11WMS4609F: Running: 0.13A, 23W. Holding: 0.09A, 7WMS8104F: Running: 16VA. Holding: 8 VAMS8109F: Running: 23VA. Holding: 7 VA

Electrical Connections:Power Lead Wires:

MS410xF and MS460xF: 32 inches (0.8m), 18 AWGMS810xF: 39 inches (1m), 18 AWG

Switch Lead Wires: 18 inches, 18 AWG, 2 color coded leads.

Controller Type:MS4104, MS4109: Line voltage (120 Vac), two-position, spst

(Series 40).MS4604, MS4609: Line voltage (230 Vac), two-position, spst

(Series 40). MS8104, MS8109: Low voltage (24 Vac), two-position, spst

(Series 80).

Device Weight:5 lb (2.3 kg).

Noise Rating (Maximum):Driving Open: 75 dBA at 1m.Holding: 20 dBA at 1m (no audible noise).

Temperature Ratings:Ambient: 0°F to 130°F (-18°C to 55°C).Shipping and Storage: -40°F to 140°F (-40°C to 60°C).

IMPORTANTThe actuator is designed to meet UL555S standards at 350°F (176°C). The actuator must be tested with the damper to achieve this rating.

Humidity Ratings:5% to 95% RH noncondensing.

Stroke:95° ± 3°, mechanically limited.

Torque Rating (at rated voltage):Spring Return:

MS4104F, MS4604F, MS8104F: 30 lb-in. (3.4 N•m).MS4109F, MS4609F, MS8109: 80 lb-in. (9 N•m).

Stall Maximum:MS4104F, MS4604F, MS8104F: 150 lb-in. (17 N•m).MS4109F, MS4609F, MS8109: 240 lb-in. (27 N•m).

350°F Driving:MS4104F, MS4604F, MS8104F: 30 lb-in. (3.4 N•m).MS4109F, MS4609F, MS8109: 80 lb-in. (9 N•m).

Timing (At Rated Torque and Voltage):Drive Open: 15 seconds typical.Spring Close: 15 seconds typical.

Design Life (at Rated Voltage):30,000 full stroke cycles.

Cycling Requirements:The actuator and the internal spring are designed to require

no special cycling during long-term holding.Honeywell recommends following all local, state and national

codes for periodic testing of the entire smoke control sys-tem. Refer to National Fire Protection Association (NFPA) National Fire Codes®: NFPA90A, NFPA92A and NFPA92B for your application.

NFPA recommends periodic examination of each fire/smoke damper (semi-annually or annually) to ensure proper per-formance.

Minimum Damper Shaft Length:2 in. (51 mm).

Mounting:Round 1/2 inch shaft adapter with 1/4 inch set screws.

Threads: ¼-20 UNC-2AMaterial: Alloy Steel hardened to HRC 45-53Thread Lock: Nylon Patch

IMPORTANTHoneywell does not recommend using linkages with these actuators because si de-loading of the output hub reduces actuator life.

Environmental Protection Ratings:NEMA, IP40.

Accessories:205649 Mounting Bracket (not supplied with actuator).

Approvals:

MS4104F, MS4109F

MS4604F, MS4609F

MS8104F, MS8109F

UL/cUL X X X

UL60730 X X X

CE X X X

C-Tick X X X

23

H A O P H U O N G - T H I N K T O G E T H E R

Head office:Address: 7/31 Song Than Business Center, Di An, Binh Duong, Vietnam.Tel: 84-650-3737-619Fax: 84-650-3737-620

Ha Noi office:Address: 16/6/102 Nguy Nhu Kon Tum Nhan Chinh, Thanh Xuan, Hanoi.Tel: 84-4-3568-3740Fax: 84-4-3568-3741

Cambodia office:Address: Office S2 Second Floor Left. Blue Green Service Office Space & Apartment. 13A, St 81 (Wat Koh) Boeung Raing, PP. Tel: 855-2322-3635 - Fax: 855-2322-3645

catalog actuator damper honey well - beeteco.com

Engineering