catalogue plastic greases - orlen oil · aluminium lubricating greases aliten ep-0 0 aluminium...

PLASTIC GREASESCATALOGUE

www.orlenoil.com

CONTENTS:

BIODEGRADABLE GREASES 04

ALUMINIUM LUBRICATING GREASES 04

BENTONITE GREASES 04

CALCIUM GREASES 04

LITHIUM GREASES 06

GREASEN ŁT-4S 2 GREASEN ŁT-4S 3LITEN EPX 00 LITEN EPX 0 LITEN EPX 1 LITEN ŁT-4P 2 LITEN ŁT-4P 3LITEN EP-0 LITEN EP-1 LITEN EP-2 LITEN EP-3 LITEN ŁT-41 LITEN ŁT-42 LITEN ŁT-43GREASE FOR TRANSMISSION

CSW-1 CSW-2 GREASEN GRAFIT GREASEN STPKALTON EP-1 KALTON EP-2 GREASE FOR BRAKE MECHANISMS LGREASE FOR BRAKE MECHANISMS Z MACHINE GREASE 2 MACHINE GREASE 3

BENTOMOS 23 BENTOR 2

ALITEN EP-0ALITEN EP-1ALITEN EP-2 ALITEN EP-3

UNITEX 00 UNITEX 1UNIVERSAL SMAROL EKO

COMPLEX LITHIUM GREASES 08

LITHIUM AND CALCIUM GREASES 10

CALCIUM SULFONATE-BASED GREASES 10

GREASES FOR SPECIAL PURPOSES 10

GREASEN N-EP GREASEN S-EP LITEN LC EP 0 LITEN LC EP 1 LITEN LC EP 2 LITEN LC EP 3

HUTPLEX WR-1HUTPLEX WR-2HUTPLEX HV

SMAROL PTFEGREASE FOR WIRE ROPES LR KZE-L GREASE KZE-Z GREASE KZ GREASE GREASE FOR CHISELS AND DRILLS

SMAROL NANO for mowing and cutting machines SMAROL NANO for bicycles, motorbikes, quads, and scooters GREASEN COMPLEX 2 GREASEN SYNTHEX HT 2 GREASEN EP 23 LITEN PREMIUM ŁT-4EP 1LITEN PREMIUM ŁT-4EP 2LITEN PREMIUM ŁT-4EP 3LITEN NANO 00LITEN NANO 2LITEN NANO 3

NAME OF GREASECONSISTENCY CLASS ACC. TO

NLGI

TYPE OF THICKENER TYPE OF OIL

VISCOSITY OF BASE OIL AT

40°C

WORKING TEMPERATURE OF GREASE °C

CLASSIFICATION TYPICAL PROPERTIESCOLOUR / LUBRICATING

SOLID BODIES APPLICATIONS ADVANTAGES / PROPERTIES

BIODEGRADABLE GREASES

UNITEX 00 00 CalciumRapeseed Biodegra-

dable30 -30÷90 MP00G-30 CBEA-00 DP ~ 100; WP ~ 200 Natural brown Unitex biodegradable greases are intended for total loss lubrication of rail

sections in railway systems and trams, as well as machines and equipment used in woodlands, at water intakes, etc., where there is a risk of environmental contamination.

These greases offer very good performance parameters: they are resistant to water, demonstrate little resistance when pumped through conduits of small diameters (which is particularly important in winter), reduce the noise generated by trams, when running along rail curves. UNITEX 1 1 Calcium

Rapeseed Biodegra-

dable30 -30÷90 MP1G-30 CBEA-1 DP ~ 100; WP ~ 200 Natural brown

UNIVERSAL SMAROL EKO

2/3 LithiumMineral

paraffinic / rapeseed

100 -30÷140 K2/3N-30 CDHA-2/3 DP ~ 210; WP ~ 200 Green

UNIVERSAL SMAROL EKO is primarily intended fro lubricating rolling and slide bearings. It guarantees excellent lubricating, even in the most demanding conditions of use. It can be successfully applied at home, in a workshop, on a farm, and to lubricate the following: hinges, locks, threads, chains, gear wheels, and rolling and slide bearings.

The UNIVERSAL SMAROL EKO is an easily biodegradable preparation, as it reaches 96% decomposition after 21 days (this result has been confirmed with a CEC L-33-A-94 test, performed by the Faculty of Environmental Engineering at the Warsaw University of Technology).

ALUMINIUM LUBRICATING GREASES

ALITEN EP-0 0 Aluminium Mineral Paraffinic 150 -20÷140 KP0N-20 BDHB-0 DP ~ 200; WP ~ 160 Natural brown

Intended for lubricating rolling bearings that work in the temperature range from -20°C to 140°C.

It is intended for lubricating bearings in machines equipped with central lubrication systems, which require pumping of grease within long distances.


ALITEN EP-2 2 Aluminium Mineral Paraffinic 150 -20÷140 KP2N-20 BDHB-2 DP ~ 200; WP ~ 160 Natural brown It is intended for lubricating bearings in machines equipped with single or

central lubrication systems that work in high ambient temperatures, and require pumping of grease within short distances.ALITEN EP-3 3 Aluminium Mineral

Paraffinic 150 -20÷140 KP3N-20 BDHB-3 DP ~ 200; WP ~ 160 Natural brown

BENTONITE GREASES

BENTOMOS 23 2 Bentonite Mineral Paraffinic 150 -10÷200 KF2S-10 AGEB-2 DP ~ 290; WP ~ 315 Black / MoS2

It is used to lubricate rolling and slide bearings, and other friction surfaces that work at a constant working temperature above 100°C, primarily in the range of 120-200°C, and if frequently changed or refilled – up to 220°C.

It is recommended to use under high loads, particularly under shock loads; it is not suitable for lubricating bearings that are actuated with a small torque, and bearings with little radial clearance.

BENTOR 2 2 Bentonite Mineral Paraffinic 150 -10÷200 K2S-10 AGEA-2 DP ~ 290; WP ~ 160 Natural brown BENTOR 2 is used to lubricate rolling and slide bearings, and other friction surfa-

ces that work at constant working temperatures from 120°C to 200°C

The Bentor 2 grease is resistant to moisture and virtually infusible; it is not suitable for lubricating bearings that are actuated with a small torque, and bearings with little radial clearance.

CALCIUM GREASES

CSW-1 1 Calcium Mineral Paraffinic 150 0÷60 K1C0 AAHA-1 DP ~ 85 Natural brown These are greases intended for CSW rolling mill equipment with improved

lubricating ability; they are used to lubricate rolling bearings of rolling stands and auxiliary equipment with a central lubrication system that work at working temperatures not exceeding 60°C, as well as other machines that work under high or shock loads.

CSW-1 is recommended, if grease is pumped through long conduits that have small diameter, or if pumped in low ambient temperatures.

CSW-2 2 Calcium Mineral Paraffinic 150 0÷60 K2C0 AAHA-2 DP ~ 85 Natural brown CSW-2 is recommended, if lubricating conduits are shorter and have a larger

diameter, and if grease is required to have sealing properties.

GREASEN GRAFIT 2 Calcium Mineral Paraffinic 150 -20÷60 KF2C-20 BAGB-2 DP ~ 85; WP ~ 250 Black / Graphite grey

GREASEN GRAFIT is intended for lubricating the following elements: suspen-sion springs in cars, open toothed gears, worm gears, the threads of screws exposed to corrosive agents, chains and other heavy-duty friction pairs. It may be applied as standard assembly grease.

It is resistant to cold water. It cannot be used to lubricate any vehicle elements other than the suspension springs. Not suitable for anti-friction bearings and other precision mechanisms.

GREASEN STP 1 Calcium Mineral Paraffinic 85 -20÷60 M1C-20 BAEA-1 DP ~ 80 Natural brown It is only intended for periodic lubricating of car chassis, pins, articulated joints,

and guides. It is not suitable for lubricating rolling bearings and water pumps.

With its soft consistency, the grease facilitates the using of lubrication devices such as pneumatic grease guns. It is reasonably resistant to cold water.

KALTON EP-1 1 Calcium Mineral Paraffinic 85 -20÷60 KP1C-20 BAHB-1 DP ~ 90; WP ~ 250 Natural brown The KALTON EP greases are intended for lubricating rolling bearings working

under heavy loads, particularly in shock load conditions, even when exposed to water, e.g. rolling mills for metal, presses, heavy construction machines, etc.

KALTON EP-1 is recommended for central lubrication systems.

KALTON EP-2 2 Calcium Mineral Paraffinic 85 -20÷60 KP2C-20 BAHB-2 DP ~ 90; WP ~ 250 Natural brown KALTON EP-2 is recommended for manual lubricating and lubricators loca-

ted near lubricating pairs.

GREASE FOR BRAKE MECHANISMS L

0 Calcium Mineral Paraffinic 150 0÷60 M0C0 AAEA-0 DP ~ 150 Natural brown

Greases for brake mechanisms (calcium-based or seasonal) are intended for lubricating timing equipment in railway brake mechanisms.

The grease for brake mechanisms L is used in the summer season.

GREASE FOR BRAKE MECHANISMS Z

00 Calcium Mineral Paraffinic 150 -20÷60 M00C-20 BAEA-00 DP ~ 150 Natural brown The grease for brake mechanisms Z is used in the winter season.

MACHINE GREASE 2

2 Calcium Mineral Paraffinic 85 -10÷60 K2C-10 AAHA-2 DP ~ 85 Natural brown

They are intended for lubricating slide bearings and other friction surfaces. The machine greases 2 and 3 are not suitable for lubricating rolling bearings.

The Machine Grease 2 is used, when grease is pumped through long condu-its of small diameter.

MACHINE GREASE 3


The Machine Grease 3 is used in lubrication, when it is required to have a higher sealing ability for bearings, and when pumping grease through conduits of larger diameters, and within smaller distances.

DIN 51 502 ISO 6743-9 DROPPING POINT DP / WELD POINT WP

PLASTIC GREASES

04_Orlen Oil_ catalogue plastic greases


NLGI



40°C




BIODEGRADABLE GREASES

UNITEX 00 00 CalciumRapeseed Biodegra-

dable30 -30÷90 MP00G-30 CBEA-00 DP ~ 100; WP ~ 200 Natural brown Unitex biodegradable greases are intended for total loss lubrication of rail

sections in railway systems and trams, as well as machines and equipment used in woodlands, at water intakes, etc., where there is a risk of environmental contamination.

These greases offer very good performance parameters: they are resistant to water, demonstrate little resistance when pumped through conduits of small diameters (which is particularly important in winter), reduce the noise generated by trams, when running along rail curves. UNITEX 1 1 Calcium

Rapeseed Biodegra-

dable30 -30÷90 MP1G-30 CBEA-1 DP ~ 100; WP ~ 200 Natural brown

UNIVERSAL SMAROL EKO

2/3 LithiumMineral

paraffinic / rapeseed

100 -30÷140 K2/3N-30 CDHA-2/3 DP ~ 210; WP ~ 200 Green

UNIVERSAL SMAROL EKO is primarily intended fro lubricating rolling and slide bearings. It guarantees excellent lubricating, even in the most demanding conditions of use. It can be successfully applied at home, in a workshop, on a farm, and to lubricate the following: hinges, locks, threads, chains, gear wheels, and rolling and slide bearings.

The UNIVERSAL SMAROL EKO is an easily biodegradable preparation, as it reaches 96% decomposition after 21 days (this result has been confirmed with a CEC L-33-A-94 test, performed by the Faculty of Environmental Engineering at the Warsaw University of Technology).

ALUMINIUM LUBRICATING GREASES


Intended for lubricating rolling bearings that work in the temperature range from -20°C to 140°C.

It is intended for lubricating bearings in machines equipped with central lubrication systems, which require pumping of grease within long distances.


ALITEN EP-2 2 Aluminium Mineral Paraffinic 150 -20÷140 KP2N-20 BDHB-2 DP ~ 200; WP ~ 160 Natural brown It is intended for lubricating bearings in machines equipped with single or

central lubrication systems that work in high ambient temperatures, and require pumping of grease within short distances.ALITEN EP-3 3 Aluminium Mineral

Paraffinic 150 -20÷140 KP3N-20 BDHB-3 DP ~ 200; WP ~ 160 Natural brown

BENTONITE GREASES

BENTOMOS 23 2 Bentonite Mineral Paraffinic 150 -10÷200 KF2S-10 AGEB-2 DP ~ 290; WP ~ 315 Black / MoS2

It is used to lubricate rolling and slide bearings, and other friction surfaces that work at a constant working temperature above 100°C, primarily in the range of 120-200°C, and if frequently changed or refilled – up to 220°C.

It is recommended to use under high loads, particularly under shock loads; it is not suitable for lubricating bearings that are actuated with a small torque, and bearings with little radial clearance.

BENTOR 2 2 Bentonite Mineral Paraffinic 150 -10÷200 K2S-10 AGEA-2 DP ~ 290; WP ~ 160 Natural brown BENTOR 2 is used to lubricate rolling and slide bearings, and other friction surfa-

ces that work at constant working temperatures from 120°C to 200°C

The Bentor 2 grease is resistant to moisture and virtually infusible; it is not suitable for lubricating bearings that are actuated with a small torque, and bearings with little radial clearance.

CALCIUM GREASES

CSW-1 1 Calcium Mineral Paraffinic 150 0÷60 K1C0 AAHA-1 DP ~ 85 Natural brown These are greases intended for CSW rolling mill equipment with improved

lubricating ability; they are used to lubricate rolling bearings of rolling stands and auxiliary equipment with a central lubrication system that work at working temperatures not exceeding 60°C, as well as other machines that work under high or shock loads.

CSW-1 is recommended, if grease is pumped through long conduits that have small diameter, or if pumped in low ambient temperatures.

CSW-2 2 Calcium Mineral Paraffinic 150 0÷60 K2C0 AAHA-2 DP ~ 85 Natural brown CSW-2 is recommended, if lubricating conduits are shorter and have a larger

diameter, and if grease is required to have sealing properties.

GREASEN GRAFIT 2 Calcium Mineral Paraffinic 150 -20÷60 KF2C-20 BAGB-2 DP ~ 85; WP ~ 250 Black / Graphite grey

GREASEN GRAFIT is intended for lubricating the following elements: suspen-sion springs in cars, open toothed gears, worm gears, the threads of screws exposed to corrosive agents, chains and other heavy-duty friction pairs. It may be applied as standard assembly grease.

It is resistant to cold water. It cannot be used to lubricate any vehicle elements other than the suspension springs. Not suitable for anti-friction bearings and other precision mechanisms.

GREASEN STP 1 Calcium Mineral Paraffinic 85 -20÷60 M1C-20 BAEA-1 DP ~ 80 Natural brown It is only intended for periodic lubricating of car chassis, pins, articulated joints,

and guides. It is not suitable for lubricating rolling bearings and water pumps.

With its soft consistency, the grease facilitates the using of lubrication devices such as pneumatic grease guns. It is reasonably resistant to cold water.

KALTON EP-1 1 Calcium Mineral Paraffinic 85 -20÷60 KP1C-20 BAHB-1 DP ~ 90; WP ~ 250 Natural brown The KALTON EP greases are intended for lubricating rolling bearings working

under heavy loads, particularly in shock load conditions, even when exposed to water, e.g. rolling mills for metal, presses, heavy construction machines, etc.

KALTON EP-1 is recommended for central lubrication systems.

KALTON EP-2 2 Calcium Mineral Paraffinic 85 -20÷60 KP2C-20 BAHB-2 DP ~ 90; WP ~ 250 Natural brown KALTON EP-2 is recommended for manual lubricating and lubricators loca-

ted near lubricating pairs.

GREASE FOR BRAKE MECHANISMS L

0 Calcium Mineral Paraffinic 150 0÷60 M0C0 AAEA-0 DP ~ 150 Natural brown

Greases for brake mechanisms (calcium-based or seasonal) are intended for lubricating timing equipment in railway brake mechanisms.

The grease for brake mechanisms L is used in the summer season.

GREASE FOR BRAKE MECHANISMS Z

00 Calcium Mineral Paraffinic 150 -20÷60 M00C-20 BAEA-00 DP ~ 150 Natural brown The grease for brake mechanisms Z is used in the winter season.

MACHINE GREASE 2


They are intended for lubricating slide bearings and other friction surfaces. The machine greases 2 and 3 are not suitable for lubricating rolling bearings.

The Machine Grease 2 is used, when grease is pumped through long condu-its of small diameter.

MACHINE GREASE 3


The Machine Grease 3 is used in lubrication, when it is required to have a higher sealing ability for bearings, and when pumping grease through conduits of larger diameters, and within smaller distances.



NLGI



40°C




LITHIUM GREASES

GREASEN ŁT-4 S 2 2 Lithium Mineral Paraffinic 85 -30÷120 KP2K-30 CCEA-2 DP ~ 200; WP ~ 200 Green The Greasen ŁT-4S greases are used to lubricate the following elements: anti-

-friction bearings in cars, cross joints while assembling linkages, strands and guides in machines or other machine parts, and slide bearings operating in the admissible temperature ranges.

GREASEN ŁT-4 S-2 is used in the following temperature range: -30÷120°C.

GREASEN ŁT-4 S 3 3 Lithium Mineral Paraffinic 85 -20÷130 KP3N-20 BDEA-3 DP ~ 200; WP ~ 200 Green GREASEN ŁT-4 S-3 is used in the following temperature range: -20÷130°C.

LITEN EPX 00 00 Lithium Mineral Paraffinic 150 -20÷120 GP00K-20 BCEB-00 DP ~ 173; WP ~ 200 Natural brown

The Liten EPX greases are intended for lubricating closed bevel and cylindrical gears.

It is used in the lower temperatures of a given temperature range, and if gears are well sealed.

LITEN EPX 0 0 Lithium Mineral Paraffinic 150 -20÷120 GP0K-20 BCEB-0 DP ~ 190; WP ~ 200 Natural brown It is used in intermediate conditions.

LITEN EPX 1 1 Lithium Mineral Paraffinic 150 -20÷120 GP1K-20 BCEB-1 DP ~ 185; WP ~ 200 Natural brown It is used in the higher temperatures of a given temperature range, and if

gears are poorly sealed.

LITEN ŁT-4 P 2 2 Lithium Mineral Paraffinic 85 -30÷140 KP2N-30 CDHA-2 DP ~ 190; WP ~ 160 Natural brown It is used for lubricating of covered rolling bearings, operating in highly deman-

ding environments, which require the following properties: oxidation resistance, corrosion protection, water resistance, and mechanical stability.

This range of greases is enriched with anti-oxidation and anti-corrosive additives, along with others that improve lubricating properties. LITEN ŁT-4P is a series of high quality, multipurpose greases.LITEN ŁT-4 P 3 3 Lithium Mineral

Paraffinic 85 -30÷140 KP3N-30 CDHA-3 DP ~ 180; WP ~ 160 Natural brown

LITEN EP-0 0 Lithium Mineral Paraffinic 150 -20÷120 KP0K-20 BCHB-0 DP ~ 190; WP ~ 250 Natural brown

The Liten EP plastic lubricants are intended for lubricating rolling bearings that work under high loads, and if bearings working under lesser loads are exposed to shock loads.

It is intended for lubricating bearings in machines equipped with central lubrication systems that work in low temperatures, and require grease to be pumped within very long distances.


It is intended for lubricating bearings in machines equipped with central lu-brication systems that work in moderate temperatures and require pumping grease within long distances.


It is intended for lubricating bearings in machines equipped with single or central lubrication systems that work in high ambient temperatures and require pumping of grease within short distances.

LITEN EP-3 3 Lithium Mineral Paraffinic 150 -20÷120 KP3K-20 BCHB-3 DP ~ 215; WP ~ 250 Natural brown It is intended for lubricating bearings in machines equipped with single

lubrication systems.

LITEN ŁT-41 1 Lithium Mineral Paraffinic 85 -30÷130 K1K-30 CCHA-1 DP ~ 200; WP ~ 250 Natural brown

The Liten ŁT-4 greases are used to lubricate rolling and slide bearings that work in the temperature range from - 30°C to +130°C.

This range of greases is enriched with anti-oxidation and anti-corrosive additives, and additives that improve lubricating properties. The selection of grease is based on the method of supplying grease to bearings (e.g. central or manual lubrication), rotational speed, and working temperature of a given bearing.


LITEN ŁT-43 3 Lithium Mineral Paraffinic 85 -30÷130 K3K-30 CCHA-3 DP ~ 205; WP ~ 160 Green

GREASE FOR TRANSMISSION

1 Lithium Mineral Paraffinic 85 -20÷120 M1K-20 BCEA-1 DP ~ 205; WP ~ 160 Natural brown This grease is intended for lubricating bevel and cylindrical gears in power

tools. This grease offers good anti-wear and anti-corrosion properties, which secure the proper operation of friction pairs, during the period of use.



PLASTIC GREASES


NLGI



40°C




LITHIUM GREASES

GREASEN ŁT-4 S 2 2 Lithium Mineral Paraffinic 85 -30÷120 KP2K-30 CCEA-2 DP ~ 200; WP ~ 200 Green The Greasen ŁT-4S greases are used to lubricate the following elements: anti-

-friction bearings in cars, cross joints while assembling linkages, strands and guides in machines or other machine parts, and slide bearings operating in the admissible temperature ranges.

GREASEN ŁT-4 S-2 is used in the following temperature range: -30÷120°C.

GREASEN ŁT-4 S 3 3 Lithium Mineral Paraffinic 85 -20÷130 KP3N-20 BDEA-3 DP ~ 200; WP ~ 200 Green GREASEN ŁT-4 S-3 is used in the following temperature range: -20÷130°C.

LITEN EPX 00 00 Lithium Mineral Paraffinic 150 -20÷120 GP00K-20 BCEB-00 DP ~ 173; WP ~ 200 Natural brown

The Liten EPX greases are intended for lubricating closed bevel and cylindrical gears.

It is used in the lower temperatures of a given temperature range, and if gears are well sealed.

LITEN EPX 0 0 Lithium Mineral Paraffinic 150 -20÷120 GP0K-20 BCEB-0 DP ~ 190; WP ~ 200 Natural brown It is used in intermediate conditions.

LITEN EPX 1 1 Lithium Mineral Paraffinic 150 -20÷120 GP1K-20 BCEB-1 DP ~ 185; WP ~ 200 Natural brown It is used in the higher temperatures of a given temperature range, and if

gears are poorly sealed.

LITEN ŁT-4 P 2 2 Lithium Mineral Paraffinic 85 -30÷140 KP2N-30 CDHA-2 DP ~ 190; WP ~ 160 Natural brown It is used for lubricating of covered rolling bearings, operating in highly deman-

ding environments, which require the following properties: oxidation resistance, corrosion protection, water resistance, and mechanical stability.

This range of greases is enriched with anti-oxidation and anti-corrosive additives, along with others that improve lubricating properties. LITEN ŁT-4P is a series of high quality, multipurpose greases.LITEN ŁT-4 P 3 3 Lithium Mineral

Paraffinic 85 -30÷140 KP3N-30 CDHA-3 DP ~ 180; WP ~ 160 Natural brown


The Liten EP plastic lubricants are intended for lubricating rolling bearings that work under high loads, and if bearings working under lesser loads are exposed to shock loads.

It is intended for lubricating bearings in machines equipped with central lubrication systems that work in low temperatures, and require grease to be pumped within very long distances.


It is intended for lubricating bearings in machines equipped with central lu-brication systems that work in moderate temperatures and require pumping grease within long distances.


It is intended for lubricating bearings in machines equipped with single or central lubrication systems that work in high ambient temperatures and require pumping of grease within short distances.

LITEN EP-3 3 Lithium Mineral Paraffinic 150 -20÷120 KP3K-20 BCHB-3 DP ~ 215; WP ~ 250 Natural brown It is intended for lubricating bearings in machines equipped with single



The Liten ŁT-4 greases are used to lubricate rolling and slide bearings that work in the temperature range from - 30°C to +130°C.

This range of greases is enriched with anti-oxidation and anti-corrosive additives, and additives that improve lubricating properties. The selection of grease is based on the method of supplying grease to bearings (e.g. central or manual lubrication), rotational speed, and working temperature of a given bearing.


LITEN ŁT-43 3 Lithium Mineral Paraffinic 85 -30÷130 K3K-30 CCHA-3 DP ~ 205; WP ~ 160 Green

GREASE FOR TRANSMISSION

1 Lithium Mineral Paraffinic 85 -20÷120 M1K-20 BCEA-1 DP ~ 205; WP ~ 160 Natural brown This grease is intended for lubricating bevel and cylindrical gears in power

tools. This grease offers good anti-wear and anti-corrosion properties, which secure the proper operation of friction pairs, during the period of use.



NLGI



40°C




COMPLEX LITHIUM GREASES

GREASEN COMPLEX 2

2 Lithium Complex

Mineral Paraffinic 85

-40÷160periodically

to 180KP2P-40 DEHB-2 DP ~ 270; WP ~ 250 Natural brown

It is intended for lubricating highly-loaded rolling and slide bearings, and other mechanisms, using also central lubrication systems.

The GREASEN COMPLEX 2 is particularly recommended for lubricating bearings in wheel hubs of cars, electric engines, hot ventilators, and also guides, articulated joints, and other mechanical elements in cars or industrial equipment. Since it is highly durable, it can be used for long-term and maintenance-free lubrication of various types of machines, without the need for additional “relubrication”, during regular operation.

GREASEN SYNTEX HT 2

2 Lithium Complex Synthetic 48 -50÷180 KP2R-50 EFHB-2 DP ~ 290; WP ~ 250 Natural brown It is intended for lubricating rolling and sliding bearings

working under high loads and at high speeds, as well as for other mechanisms.

The SYNTEX HT 2 is virtually infusible and offers antistatic properties; it is also compatible with elements made of copper alloys, and with many types of elastomers, which enables lubricating friction connections, such as metal-plastic, or metal-rubber. It also enables lubricating mechanisms exposed to: impact loads, vibrations, high dustiness, impact of humidity, and washing out with water.

GREASEN EP 23 2 Lithium Complex

Mineral Paraffinic 150 -30÷140 KF2N-30 CDEB-2 DP ~ 190; WP ~ 315 Black / MoS2

GREASEN EP-23 is intended for lubricating highly-loaded friction connections and intersecting axis gears in cutting machines. It is also recommended for applications that require frequent changes in flow directions, or a combination of low speeds of motion and high loads, e.g. in constant velocity joints.

GREASEN EP-23 is a complex lithium grease, with an addition of molybde-num disulfide (3%). It is a grease resistant to moisture, steam, and weak acids and bases. This grease is also resistant to vibrations, high pressures, and shock loads.

LITEN PREMIUM ŁT-4EP 1

1 Lithium Complex

Mineral Paraffinic 150 -30÷140 KP1N-30 CDHB-1 DP ~ 251; WP ~ 250 Natural brown

The LITEN PREMIUM ŁT-4EP GREASES are used to lubricate the following ele-ments: rolling and slide bearings – also installed in central lubrication systems, slow-speed gears, gears working under low and average loads, articulated joints and sliding guides in machines, and other friction pairs used for industrial appli-cations. It can be used successfully as multi-functional automotive grease.

They are characteristic for high tribological parameters and resistance to ageing. The modern composition of improvers used in the LITEN PREMIUM ŁT-4EP greases also results in a higher dropping point, improved low-tempe-rature properties and a higher resistance to washing out with water, when compared to standard lithium greases.


2 Lithium Complex


They are characteristic for high tribological parameters and resistance to ageing. The modern composition of improvers used in the LITEN® PREMIUM ŁT-4EP greases also results in a higher dropping point, improved low-tempe-rature properties and a higher resistance to washing out with water, when compared to standard lithium greases. LITEN PREMIUM ŁT-4EP2 meets the following specifications: ZETOR (Proxima, Proxima Plower, and Forterra).


3 Lithium Complex


They are characteristic for high tribological parameters and resistance to ageing. The modern composition of improvers used in the LITEN® PREMIUM ŁT-4EP greases also results in a higher dropping point, improved low-tempe-rature properties and a higher resistance to washing out with water, when compared to standard lithium greases.

LITEN NANO 00 0 Lithium Complex

Naphthenic oil 110 -30÷140 KPF2N-30 CDEB-00 DP ~ 190 ; WP ~ 500 Silver-black /

Nano FormulaLITEN NANO is intended for lubricating rolling and slide bearings, and friction pairs working under high loads, in the following temperature range: from -30°C to + 140°C. LITEN NANO is also recommended in applications that feature fre-quent changes in the direction of motion, or a combination of low speeds and high loads (especially shock loads), e.g. constant velocity joints. High anti-wear parameters reduce the friction between mating surfaces, which greatly reduces their wear.

The high content of the NANO composition ensures that the grease adheres perfectly to lubricated surfaces, thus creating a durable layer resistant to high loads, which reduces friction and wear of mating surfaces.



Nano Formula



Nano Formula

SMAROL NANO GREASE for cutting and mowing machines

2 Lithium Complex

Mineral Paraffinic 100 -30÷160 KF2P-30 CEDB-2 DP ~ 210; WP ~ 500 Silver-black /

Nano Formula

SMAROL NANO has been designed for mowing and cutting machines, and it is primarily intended for lubricating intersecting axis gears in all types of cutting machines and trimmers, both with diesel and electric engines. It can be successfully applied in households, workshops and on farms, to lubricate and secure hinges, locks, threads, and elements of vehicles and machines, against corrosion, within a broad range of temperatures.

The grease offers high resistance to washing out with water, because of the type of the applied thickener. This grease is resistant to corrosion, oxidation, and contains the unique NANO formula, which is composed of a mixture of constant nanomolecular lubricating bodies. The high content of the NANO composition makes the grease adhere perfectly to lubricated surfaces, thus creating a permanent layer, resistant to high loads, moisture, acids, bases, and extremely high temperatures.

SMAROL NANO GREASEfor bicycles, motorbikes, quads, and scooters

2 Lithium Complex

Naphthene / Mineral

Paraffinic 100 -30÷140 KF2N-30 CDEB-2 DP ~ 200; WP ~ 500 Silver-black / Nano Formula

The SMAROL NANO greases have been designed for bicycles, motorbikes, quads, and scooters. They are primarily intended for lubricating bearings, chains, and components working in the temperature range from -30 to 140°C. It ensures excellent lubrication, even in the most difficult working conditions.




PLASTIC GREASES


NLGI



40°C




COMPLEX LITHIUM GREASES

GREASEN COMPLEX 2

2 Lithium Complex

Mineral Paraffinic 85

-40÷160periodically

to 180KP2P-40 DEHB-2 DP ~ 270; WP ~ 250 Natural brown

It is intended for lubricating highly-loaded rolling and slide bearings, and other mechanisms, using also central lubrication systems.

The GREASEN COMPLEX 2 is particularly recommended for lubricating bearings in wheel hubs of cars, electric engines, hot ventilators, and also guides, articulated joints, and other mechanical elements in cars or industrial equipment. Since it is highly durable, it can be used for long-term and maintenance-free lubrication of various types of machines, without the need for additional “relubrication”, during regular operation.

GREASEN SYNTEX HT 2

2 Lithium Complex Synthetic 48 -50÷180 KP2R-50 EFHB-2 DP ~ 290; WP ~ 250 Natural brown It is intended for lubricating rolling and sliding bearings

working under high loads and at high speeds, as well as for other mechanisms.

The SYNTEX HT 2 is virtually infusible and offers antistatic properties; it is also compatible with elements made of copper alloys, and with many types of elastomers, which enables lubricating friction connections, such as metal-plastic, or metal-rubber. It also enables lubricating mechanisms exposed to: impact loads, vibrations, high dustiness, impact of humidity, and washing out with water.

GREASEN EP 23 2 Lithium Complex

Mineral Paraffinic 150 -30÷140 KF2N-30 CDEB-2 DP ~ 190; WP ~ 315 Black / MoS2

GREASEN EP-23 is intended for lubricating highly-loaded friction connections and intersecting axis gears in cutting machines. It is also recommended for applications that require frequent changes in flow directions, or a combination of low speeds of motion and high loads, e.g. in constant velocity joints.

GREASEN EP-23 is a complex lithium grease, with an addition of molybde-num disulfide (3%). It is a grease resistant to moisture, steam, and weak acids and bases. This grease is also resistant to vibrations, high pressures, and shock loads.


1 Lithium Complex


The LITEN PREMIUM ŁT-4EP GREASES are used to lubricate the following ele-ments: rolling and slide bearings – also installed in central lubrication systems, slow-speed gears, gears working under low and average loads, articulated joints and sliding guides in machines, and other friction pairs used for industrial appli-cations. It can be used successfully as multi-functional automotive grease.

They are characteristic for high tribological parameters and resistance to ageing. The modern composition of improvers used in the LITEN PREMIUM ŁT-4EP greases also results in a higher dropping point, improved low-tempe-rature properties and a higher resistance to washing out with water, when compared to standard lithium greases.


2 Lithium Complex


They are characteristic for high tribological parameters and resistance to ageing. The modern composition of improvers used in the LITEN® PREMIUM ŁT-4EP greases also results in a higher dropping point, improved low-tempe-rature properties and a higher resistance to washing out with water, when compared to standard lithium greases. LITEN PREMIUM ŁT-4EP2 meets the following specifications: ZETOR (Proxima, Proxima Plower, and Forterra).


3 Lithium Complex


They are characteristic for high tribological parameters and resistance to ageing. The modern composition of improvers used in the LITEN® PREMIUM ŁT-4EP greases also results in a higher dropping point, improved low-tempe-rature properties and a higher resistance to washing out with water, when compared to standard lithium greases.



Nano FormulaLITEN NANO is intended for lubricating rolling and slide bearings, and friction pairs working under high loads, in the following temperature range: from -30°C to + 140°C. LITEN NANO is also recommended in applications that feature fre-quent changes in the direction of motion, or a combination of low speeds and high loads (especially shock loads), e.g. constant velocity joints. High anti-wear parameters reduce the friction between mating surfaces, which greatly reduces their wear.

The high content of the NANO composition ensures that the grease adheres perfectly to lubricated surfaces, thus creating a durable layer resistant to high loads, which reduces friction and wear of mating surfaces.



Nano Formula



Nano Formula

SMAROL NANO GREASE for cutting and mowing machines

2 Lithium Complex

Mineral Paraffinic 100 -30÷160 KF2P-30 CEDB-2 DP ~ 210; WP ~ 500 Silver-black /

Nano Formula

SMAROL NANO has been designed for mowing and cutting machines, and it is primarily intended for lubricating intersecting axis gears in all types of cutting machines and trimmers, both with diesel and electric engines. It can be successfully applied in households, workshops and on farms, to lubricate and secure hinges, locks, threads, and elements of vehicles and machines, against corrosion, within a broad range of temperatures.


SMAROL NANO GREASEfor bicycles, motorbikes, quads, and scooters

2 Lithium Complex

Naphthene / Mineral

Paraffinic 100 -30÷140 KF2N-30 CDEB-2 DP ~ 200; WP ~ 500 Silver-black / Nano Formula

The SMAROL NANO greases have been designed for bicycles, motorbikes, quads, and scooters. They are primarily intended for lubricating bearings, chains, and components working in the temperature range from -30 to 140°C. It ensures excellent lubrication, even in the most difficult working conditions.




NLGI



40°C




LITHIUM AND CALCIUM GREASES

GREASEN N-EP 00/000 Lithium-calcium

Mineral Naphthene 36 -30÷90 KP00/000E-30 CBEB-00/000 DP ~ 184; WP ~ 250 Natural brown They are primarily intended for lubricating friction pairs in heavy commercial

vehicles and buses, using central lubrication systems. They can be used to lubri-cate various types of reduction gears, lubricated with plastic greases.

GREASEN N-EP 00/000 is applied in the temperature range from -30°C do +90°C

GREASEN S-EP 00/000 Lithium-calcium Synthetic 19 -45÷100 KP00/000G-45 EBEB-00/000 DP ~ 182; WP ~ 250 Natural brown GREASEN S-EP 00/000 is applied in the temperature range from -45°C do +90°C

LITEN LC EP 0* 0 Lithium-calcium

Mineral Paraffinic 85 -30÷120 KP0K-30 CCHB-0 DP ~ 165; WP ~ 250 Natural brown

The LITEN LC EP greases are primarily intended for lubricating rolling bearings that work under high loads, i.e. when C/P < 7 (applicable to bearings that work mainly under radial loads), or C/P > 15 (applicable to bearings that work mainly under axial loads), and also when bearings working under lower loads are exposed to shock loads.

It is intended for lubricating bearings in machines equipped with central lubrication systems that work in low temperatures, and require pumping grease within very long distances.



It is intended for lubricating bearings in machines equipped with central lu-brication systems that work in moderate ambient temperatures, and require pumping grease within long distances.



It is intended for lubricating bearings in machines equipped with single and central lubrication systems that work in high ambient temperatures, and require pumping grease within short distances.


Mineral Paraffinic 85 -30÷120 KP3K-30 CCHB-3 DP ~ 180; WP ~ 250 Natural brown It is intended for lubricating bearings in machines equipped with single


CALCIUM SULFONATE-BASED GREASES

HUTPLEX WR-1 1 Calcium sulfonate

Mineral Paraffinic 180 -30÷180 K1R-30 CFIB-1 DP > 300; WP ~ 800 Amber The HUTPLEX WR high-temperature sulfonate greases are intended for lubri-

cating elements of machines used in the metallurgic industry, and particularly bearings in rolls installed in rolling strands, and other friction pairs exposed to high temperatures.

The unique thermal stability of the HUTLPEX WR greases enables them to return to their original structure, when ambient temperature has been re-stored. They are an excellent choice, when lubricating elements of machines and equipment in coal- and copper-mining, cement plants, steel industry, heavy industry, and for all friction pairs exposed to extreme pressures and water impact, requiring maximum anticorrosion protection.


Mineral Paraffinic 180 -25÷180 K2R-25 BFIB-2 DP > 300; WP ~ 800 Amber

HUTPLEX HV 1.5 Calcium sulfonate

Mineral Paraffinic 420 -30÷180 K1,5R-30 CFIB-1,5 DP > 300; WP ~ 800 Amber

The HUTPLEC HV high-temperature sulfonate greases are highly adhesive EP greases, intended for lubricating elements of machines working in the mining, metallurgic, heavy, and naval industries, and particularly for friction pairs exposed to high shock loads and low torques, working in high dustiness and exposed to the impact of water and brine.

This grease is an excellent choice in coal- and copper-mining, when lubricat-ing bearings, pin joints, and other mechanisms in machines and equipment working in the temperature range from -30 to +180°C. HUTPLEX HV also performs well in demanding metallurgical applications, when lubricating bearings in breast rollers of rolling strands.

GREASES FOR SPECIAL PURPOSES

SMAROL PTFE Grease in the form of spray PTFE Mineral

Paraffinic– -10÷250 – – – White

SMAROL PTFE is a special type of grease that offers very powerful adhesion and good penetration properties. It is intended for lubricating machine parts expo-sed to high temperatures or significant impacts water. When applied and dried up, it creates a protective layer of oil film on lubricated elements, which provides excellent protection against oxidation, thus improving resistance to ageing. It is resistant to water, steam, and aggressive agents (most acids and lye).

In addition to individual applications, it can be used in the textile and ceramic industries, glass-works, brickyards, foundries, metallurgical plants, sewage-treatment plants, power plants, rolling mills, harbours, shipyards, and to lubricate the following elements: slide bearings and system linkages, chains – also equipped with O-ring or X-ring seals, toothed bars, chain wheels, levers, sliding guides, linear guide systems, spindles, hinges, wire ropes, ball-and-socket joints, and conveyors working in furnaces and driers.

GREASE FOR WIRE ROPES H LR

4 Special Mineral Paraffinic 540 -20÷60 M5C-20 BABA-4 DP ~ 80; WP ~ 102 Natural brown The LR grease is intended for maintaining wire ropes of various types / structures,

during their manufacture.It is not suitable for lubricating hoisting ropes of drum hoists, nor ropes in hoists with the Koepe pulley.

KZE-L GREASE – Asphaltic Mineral Paraffinic 85 0÷60 GPC-0 AAHB WP ~ 250 Black

Greases of the KZ E type are used to lubricate closed bevel gears in the axle set of electric traction units.

The KZ E-L grease is used in the summer season, in the temperature range from 0°C to 60°C.

KZE-Z GREASE – Asphaltic Mineral Paraffinic 85 -25÷50 GPC-25 BAHB WP ~ 250 Black The KZ E-Z grease is used in the winter season, in the temperature range

from 25°C to 40°C.

KZ GREASE – Asphaltic Mineral oil + solvent 85 -20÷50 - BAHA WP ~ 250 Black It is intended for lubricating low-speed and open toothed gears (frontal and

conical), working at the temperature of up to +40°C. It is suitable for lubricating worms gears, made of bronze and cast steel.

Grease for chisels and drills

1 Calcium Mineral Paraffinic 85 -20÷60 M1C-20 BAEA-1 DP ~ 80 Natural brown

This grease is intended for periodic protecting of chisels, drills, and other metal elements in power tools, against corrosion. The grease is resistant to water and moisture, within the temperature range from -20°C to +60°C.

The grease is resistant to water and moisture, within the temperature range from -20°C to +60°C. It prevents the seizing of a drill / chisel and handles of power tools. The grease can be applied in the majority of machines and equipment that require grease of a certain consistency.



* Products available on request.

PLASTIC GREASES


NLGI



40°C




LITHIUM AND CALCIUM GREASES

GREASEN N-EP 00/000 Lithium-calcium

Mineral Naphthene 36 -30÷90 KP00/000E-30 CBEB-00/000 DP ~ 184; WP ~ 250 Natural brown They are primarily intended for lubricating friction pairs in heavy commercial

vehicles and buses, using central lubrication systems. They can be used to lubri-cate various types of reduction gears, lubricated with plastic greases.

GREASEN N-EP 00/000 is applied in the temperature range from -30°C do +90°C

GREASEN S-EP 00/000 Lithium-calcium Synthetic 19 -45÷100 KP00/000G-45 EBEB-00/000 DP ~ 182; WP ~ 250 Natural brown GREASEN S-EP 00/000 is applied in the temperature range from -45°C do +90°C



The LITEN LC EP greases are primarily intended for lubricating rolling bearings that work under high loads, i.e. when C/P < 7 (applicable to bearings that work mainly under radial loads), or C/P > 15 (applicable to bearings that work mainly under axial loads), and also when bearings working under lower loads are exposed to shock loads.

It is intended for lubricating bearings in machines equipped with central lubrication systems that work in low temperatures, and require pumping grease within very long distances.



It is intended for lubricating bearings in machines equipped with central lu-brication systems that work in moderate ambient temperatures, and require pumping grease within long distances.



It is intended for lubricating bearings in machines equipped with single and central lubrication systems that work in high ambient temperatures, and require pumping grease within short distances.


Mineral Paraffinic 85 -30÷120 KP3K-30 CCHB-3 DP ~ 180; WP ~ 250 Natural brown It is intended for lubricating bearings in machines equipped with single


CALCIUM SULFONATE-BASED GREASES


Mineral Paraffinic 180 -30÷180 K1R-30 CFIB-1 DP > 300; WP ~ 800 Amber The HUTPLEX WR high-temperature sulfonate greases are intended for lubri-

cating elements of machines used in the metallurgic industry, and particularly bearings in rolls installed in rolling strands, and other friction pairs exposed to high temperatures.

The unique thermal stability of the HUTLPEX WR greases enables them to return to their original structure, when ambient temperature has been re-stored. They are an excellent choice, when lubricating elements of machines and equipment in coal- and copper-mining, cement plants, steel industry, heavy industry, and for all friction pairs exposed to extreme pressures and water impact, requiring maximum anticorrosion protection.


Mineral Paraffinic 180 -25÷180 K2R-25 BFIB-2 DP > 300; WP ~ 800 Amber

HUTPLEX HV 1.5 Calcium sulfonate

Mineral Paraffinic 420 -30÷180 K1,5R-30 CFIB-1,5 DP > 300; WP ~ 800 Amber

The HUTPLEC HV high-temperature sulfonate greases are highly adhesive EP greases, intended for lubricating elements of machines working in the mining, metallurgic, heavy, and naval industries, and particularly for friction pairs exposed to high shock loads and low torques, working in high dustiness and exposed to the impact of water and brine.

This grease is an excellent choice in coal- and copper-mining, when lubricat-ing bearings, pin joints, and other mechanisms in machines and equipment working in the temperature range from -30 to +180°C. HUTPLEX HV also performs well in demanding metallurgical applications, when lubricating bearings in breast rollers of rolling strands.

GREASES FOR SPECIAL PURPOSES

SMAROL PTFE Grease in the form of spray PTFE Mineral

Paraffinic– -10÷250 – – – White

SMAROL PTFE is a special type of grease that offers very powerful adhesion and good penetration properties. It is intended for lubricating machine parts expo-sed to high temperatures or significant impacts water. When applied and dried up, it creates a protective layer of oil film on lubricated elements, which provides excellent protection against oxidation, thus improving resistance to ageing. It is resistant to water, steam, and aggressive agents (most acids and lye).

In addition to individual applications, it can be used in the textile and ceramic industries, glass-works, brickyards, foundries, metallurgical plants, sewage-treatment plants, power plants, rolling mills, harbours, shipyards, and to lubricate the following elements: slide bearings and system linkages, chains – also equipped with O-ring or X-ring seals, toothed bars, chain wheels, levers, sliding guides, linear guide systems, spindles, hinges, wire ropes, ball-and-socket joints, and conveyors working in furnaces and driers.

GREASE FOR WIRE ROPES H LR

4 Special Mineral Paraffinic 540 -20÷60 M5C-20 BABA-4 DP ~ 80; WP ~ 102 Natural brown The LR grease is intended for maintaining wire ropes of various types / structures,

during their manufacture.It is not suitable for lubricating hoisting ropes of drum hoists, nor ropes in hoists with the Koepe pulley.

KZE-L GREASE – Asphaltic Mineral Paraffinic 85 0÷60 GPC-0 AAHB WP ~ 250 Black

Greases of the KZ E type are used to lubricate closed bevel gears in the axle set of electric traction units.

The KZ E-L grease is used in the summer season, in the temperature range from 0°C to 60°C.

KZE-Z GREASE – Asphaltic Mineral Paraffinic 85 -25÷50 GPC-25 BAHB WP ~ 250 Black The KZ E-Z grease is used in the winter season, in the temperature range

from 25°C to 40°C.

KZ GREASE – Asphaltic Mineral oil + solvent 85 -20÷50 - BAHA WP ~ 250 Black It is intended for lubricating low-speed and open toothed gears (frontal and

conical), working at the temperature of up to +40°C. It is suitable for lubricating worms gears, made of bronze and cast steel.

Grease for chisels and drills

1 Calcium Mineral Paraffinic 85 -20÷60 M1C-20 BAEA-1 DP ~ 80 Natural brown

This grease is intended for periodic protecting of chisels, drills, and other metal elements in power tools, against corrosion. The grease is resistant to water and moisture, within the temperature range from -20°C to +60°C.

The grease is resistant to water and moisture, within the temperature range from -20°C to +60°C. It prevents the seizing of a drill / chisel and handles of power tools. The grease can be applied in the majority of machines and equipment that require grease of a certain consistency.


NLGI class Consistency Penetration (after kneading at the temperature of 25°C)

000 Fluid 445 - 475

00 Semi-fluid 400 - 430

0 Thick 335 - 385

1 Semi-solid 310 - 340

2 Soft (standard grease) 265 - 295

3 Average 220 - 250

4 Dense 175 - 205

5 Semi-hard 130 - 160

6 Hard 85 - 115


PLASTIC GREASES

NOTES


www.orlenoil.com

July 2013

ORLEN OIL Sp. z o.o.

ul. Opolska 100, 31-323 Kraków

Tel. +48 12 665 55 00 (Head Office)

Fax +48 12 665 55 01

Email : [email protected]

Info line: 0 801 102 103 0 801 102 103

catalogue plastic greases - orlen oil · aluminium lubricating greases aliten ep-0 0 aluminium...

Documents