catia v5r17 course catalog

CATIA V5R17Course Material Catalog

September 2006 Edition

CATIA V5R17 Course Material Catalog Sep 21, 2006 1/107

CATIA V5R17 Course Material Catalog

CATIA Course Material .......................................................................... 5Analysis Solutions ................................................................................................ 5

EST: ELFINI Structural Analysis (EDU-CAT-E-EST-F - V5R17) ............................................. 6FMD: FEM Solid (EDU-CAT-E-FMD-F - V5R17) ..................................................................... 8FMS: FEM Surface (EDU-CAT-E-FMS-F - V5R17) ............................................................... 10GAS: Generative Assembly Structural Analysis (EDU-CAT-E-GAS-F - V5R17) ................... 12GDY: Generative Dynamic Response Analysis (EDU-CAT-E-GDY-F - V5R17) ................... 14GPE: Generative Part Structural Analysis Expert (EDU-CAT-E-GPE-F - V5R17) ................. 15GPF: Generative Part Structural Analysis Fundamentals (EDU-CAT-E-GPF-F - V5R17) ..... 16TAA: Tolerance Analysis of Deformable Assembly (EDU-CAT-E-TAA-F - V5R17) .............. 18

Equipment & Systems Engineering Solutions .................................................... 19CBD: Circuit Board Design (EDU-CAT-E-CBD-F - V5R17) ................................................... 20EHF: Electical Harness Flattening (EDU-CAT-E-EHF-F - V5R17) ........................................ 21ELI: Electrical Librarian & Harness Installation (EDU-CAT-E-ELI-F - V5R17) ....................... 22EWR: Electrical Wire Routing (EDU-CAT-E-EWR-F - V5R17) .............................................. 24TUB: Tubing Design (EDU-CAT-E-TUB-F - V5R17) .............................................................. 25TUD: Tubing Diagrams (EDU-CAT-E-TUD-F - V5R17) ......................................................... 26TUS: Tubing Catalogs (2D Diagrams & 3D Design) (EDU-CAT-E-TUS-A - V5R17) ............. 27

Infrastructure Solutions ....................................................................................... 28ADM: V5 Administration (EDU-CAT-E-ADM-F - V5R17) ....................................................... 29PRO: CATIA Tools for Proficient Users (EDU-CAT-E-PRO-F - V5R17) ................................ 30V4A: V4/V5 Advanced Interoperability (EDU-CAT-E-V4A-A - V5R17) .................................. 31V4I: V4 Integration (EDU-CAT-E-V4I-F - V5R17) .................................................................. 32VBA: CATIA V5 Automation (EDU-CAT-E-VBA-F - V5R17) .................................................. 33

Mechanical Design Solutions .............................................................................. 34ASL: Aerospace Sheet Metal Design (EDU-CAT-E-ASL-F - V5R17) .................................... 35ASM: CATIA Product Design Expert (EDU-CAT-E-ASM-A - V5R17) .................................... 36CCV: Core & Cavity Design (EDU-CAT-E-CCV-F - V5R17) .................................................. 37DDR: CATIA Detail Drafting (EDU-CAT-E-DDR-F - V5R17) ................................................. 38DRA: Advanced Drafting & Customization (EDU-CAT-E-DRA-A - V5R17) ........................... 39FMP: Functional Molded Part (EDU-CAT-E-FMP-F - V5R17) ............................................... 40FR1: Part Design Feature Recognition (EDU-CAT-E-FR1-F - V5R17) ................................. 41FTA: 3D Functional Tolerancing & Annotation (EDU-CAT-E-FTA-F - V5R17) ...................... 42GS1: CATIA Surface Design (EDU-CAT-E-GS1-F - V5R17) ................................................. 43HA1: Healing Assistant (EDU-CAT-E-HA1-F - V5R17) ......................................................... 45LO1: 2D Layout for 3D Design (EDU-CAT-E-LO1-F - V5R17) .............................................. 46MD2: Mechanical Design V5R17 Update (EDU-CAT-E-MD2-U - V5R17) ............................. 47MTD: Mold Tooling Design (EDU-CAT-E-MTD-F - V5R17) ................................................... 48PDG: CATIA Part Design Expert (EDU-CAT-E-PDG-A - V5R17) ......................................... 49SMD: CATIA Generative Sheet Metal Design (EDU-CAT-E-SMD-F - V5R17) ...................... 50SMD: CATIA Generative Sheet Metal Design V5R17 Update (EDU-CAT-E-SMD-U - V5R17)


SR1: Structure Design (EDU-CAT-E-SR1-F - V5R17) .......................................................... 54SRA: Structure Design Administration (EDU-CAT-E-SRA-A - V5R17) .................................. 56TG1: Tooling Design (EDU-CAT-E-TG1-F - V5R17) ............................................................. 57V5E: CATIA V5 Expert Mechanical Designer (EDU-CAT-E-V5E-A - V5R17) ....................... 58V5F: CATIA V5 Fundamentals (EDU-CAT-E-V5F-F - V5R17) .............................................. 60

Machining Solutions ........................................................................................... 62AMG: Advanced Part Machining (EDU-CAT-E-AMG-F - V5R17) .......................................... 63LMG: Lathe Machining (EDU-CAT-E-LMG-F - V5R17) ......................................................... 64MMG: Multi-Axis Surface Machining (EDU-CAT-E-MMG-F - V5R17) ................................... 65MPA: Prismatic Machining Preparation Assistant (EDU-CAT-E-MPA-F - V5R17) ................ 66MPG: Multi Pocket Machining (EDU-CAT-E-MPG-F - V5R17) .............................................. 67NCI: Numerical Control Infrastructure (EDU-CAT-E-NCI-F - V5R17) .................................... 68PMG: Prismatic Machining (EDU-CAT-E-PMG-F - V5R17) .................................................. 70SMG: 3-Axis Surface Machining (EDU-CAT-E-SMG-F - V5R17) .......................................... 71STL: STL Rapid Prototyping (EDU-CAT-E-STL-F - V5R17) .................................................. 73

Product Synthesis Solutions ............................................................................... 74HMN: Human Modeling (EDU-CAT-E-HMN-F - V5R17) ........................................................ 75KWA: Knowledge Advisor (EDU-CAT-E-KWA-F - V5R17) .................................................... 76KWE: Knowledge Expert (EDU-CAT-E-KWE-F - V5R17) ..................................................... 77KWF: Knowledge Fundamentals (EDU-CAT-E-KWF-F - V5R17) ......................................... 78PEO: Product Engineering Optimizer (EDU-CAT-E-PEO-F - V5R17) ................................... 79

Shape Design & Styling Solutions ...................................................................... 80DL1: Developed Shapes (EDU-CAT-E-DL1-F - V5R17) ........................................................ 81DSE: Digitized Shape Editor (EDU-CAT-E-DSE-F - V5R17) ................................................. 82FSK: FreeStyle Sketch Tracer (EDU-CAT-E-FSK-F - V5R17) .............................................. 83FSS: FreeStyle Shaper, Optimizer & Profiler (EDU-CAT-E-FSS-F - V5R17) ........................ 84GSD: Surface Design Expert (EDU-CAT-E-GSD-F - V5R17) ............................................... 85GSO: Generative Shape Optimizer (EDU-CAT-E-GSO-F - V5R17) ...................................... 87HD2: Generative Shape Design V5R17 Update (EDU-CAT-E-HD2-U - V5R17) ................... 89IMA: Imagine & Shape (EDU-CAT-E-IMA-F - V5R17) ........................................................... 90PHS: Photo Studio (EDU-CAT-E-PHS-F - V5R17) ................................................................ 92PSO: Photo Studio Optimizer (EDU-CAT-E-PSO-F - V5R17) ............................................... 93QSR: Quick Surface Reconstruction (EDU-CAT-E-QSR-F - V5R17) .................................... 94RSO: Realistic Shape Optimizer (EDU-CAT-E-RSO-F - V5R17) .......................................... 95RTR: Real Time Rendering (EDU-CAT-E-RTR-F - V5R17) .................................................. 96V5S: V5 Surface Design (EDU-CAT-E-V5S-F - V5R17) ........................................................ 97

Digital Mock-Up Course Material ......................................................... 99Digital Mock-Up Solutions .................................................................................. 99

ANR: DMU Engineering Analysis Review (EDU-DMU-E-ANR-F - V5R17) ......................... 100DMB: Digital Mock Up Basics (EDU-DMU-E-DMB-F - V5R17) ........................................... 101DMN: Digital Mock Up Navigator (EDU-DMU-E-DMN-F - V5R17) ...................................... 102


DMO: Digital Mock Up Optimizer (EDU-DMU-E-DMO-F - V5R17) ...................................... 103DMU: Digital Mock-Up V5R17 Update (EDU-DMU-E-DMU-U - V5R17) ............................. 104FIT: Digital Mock-Up Fitting Simulator (EDU-DMU-E-FIT-F - V5R17) ................................. 105KIN: Digital Mock-Up Kinematics Simulator (EDU-DMU-E-KIN-F - V5R17) ........................ 106SPA: Digital Mock-Up Space Analysis (EDU-DMU-E-SPA-F - V5R17) ............................... 107


CATIA Course Material

Analysis Solutions

CATIA V5R17 Course Catalog Sep 21, 2006 5/107

AnalysisSolutions

EST: ELFINI Structural Analysis

EDU-CAT-E-EST-FCourse Code EDU-CAT-E-EST-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EST-FI-V5R17 Foils: EDU-CAT-E-EST-FF-V5R17 Exercises: EDU-CAT-E-EST-FX-V5R17

Objectives- Map external load data and combine loads/masses- Optimize the computation of frequency analyses- Analyze a sub-set of a symmetric model- Manage multi-analyses and find critical values- Perform a buckling analysis- Customize the display of results and reports

Participants' ProfileMechanical DesignersStructural Analysts

Prerequisites- Generative Part Structural Analysis Expert


ContentThis course will teach you how to re-use existing loads, and apply combinedloads and conditions to a mesh model. You will learn how to optimizecomputation times, manage complex analysis cases, and customize theresulting output.

Advanced Pre-Processing- Visualization Transferred onto Mesh- Bearing Loads- Data Mapping- Self-Balancing on Load set- Combined Loads/Masses- Thermo-mechanical loads - Local 1D Property- Variable cross section beams- Advanced 2D properties- Periodic conditions- Grouping for Pre-processing- Local Adaptivity Specifications- Mapping Property- Import V4

Advanced Analysis Case Management- Multi Analysis Case- The Buckling Case- Contact Pressures- Frequency shifting- Combined Case- Static constrained modes Case- Envelop Case- Pre-processing Case- Multi Loads Case- Transfer of Computed Loads/Displacements

Advanced Post-Processing- Advanced Customisation- Advanced Report- Advanced images- Export of nodal values- Grouping- Local sensors- Image template- FEM model images

EST Functionalities

Frequently Asked Questions

ExercisesEx. 1: Advanced Analysis of Landing Gear Assembly (120min) / AerospaceEx. 2: Bearing loads Analysis (10min) / All sectorsEx. 3: Hanger Buckling Analysis (15min) / All sectorsEx. 4: Door Fuselage Buckling Analysis (30min) / AerospaceEx. 5: Pressure Contact between Rod and Axis (20min) / AutomotiveEx. 6: Blade Analysis (120min) / AerospaceEx. 7: Truss Analysis (120min) / All sectorsEx. 8: Toy surfacic Analysis (120min) / Fabrication & Assemblies ConsumerGoodsEx. 9: Static constrained modes / All sectorsEx. 10: Adaptivity (120min) / All sectorsEx. 11: Automation (30min) / All sectorsEx. 12: 12. Static Constrained Modes Case (10min) / All sectorsEx. 13: 13. Applying Mapping Property (30min) / All sectorsEx. 14: 14. Transfer of Loads (15min) / All sectorsEx. 15: 15. Transfer of Solution (15min) / All sectorsEx. 16: Multi-Loads Analysis (30min) / All sectors


AnalysisSolutions

FMD: FEM Solid

EDU-CAT-E-FMD-FCourse Code EDU-CAT-E-FMD-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMD-FI-V5R17 Foils: EDU-CAT-E-FMD-FF-V5R17 Exercises: EDU-CAT-E-FMD-FX-V5R17 Detailed Steps: EDU-CAT-E-FMD-FS-V5R17

Objectives- Generate a solid mesh from a solid model or an existing surface mesh- Generate a solid mesh using Mesh Transformations- Generate a solid mesh using Mesh Extrusions- Analyze Quality of 3D elements- Perform a cutting plane analysis on a solid mesh- Import / Export solid meshes

Participants' ProfileStructural Analysts

Prerequisites- FEM Surface


ContentThis course will teach you how to generate a 3D tetrahedron mesh by focusingon the transformation methods used to create new mesh models from anexisting 2D or 3D mesh. It will teach you how to analyze the quality of theresulting mesh and visualize internal mesh elements.

Introduction to FEM Solid- What is FEM Solid- User Interface- General Process for Solid Mesh Generation- Accessing the Workbench

Tetrahedron Filler- What is Tetrahedron Filler- Tetrahedron Filler Parameters- Generating Solid Mesh Using Tetrahedron Filler

OCTREE Tetrahedron Mesher- What is OCTREE Tetrahedron Mesher- OCTREE Tetrahedron Mesher - Local Parameters- OCTREE Tetrahedron mesher - Quality Parameters- OCTREE Tetrahedron mesher - Other Parameters- Generating Mesh Using OCTREE Tetrahedron Mesher

Sweep 3D- What is Sweep 3D- Generating Solid Mesh Using Sweep 3D

Mesh Part Transformations- What is Mesh Part Transformations- Solid Mesh Generation Using Translation- Solid Mesh Generation Using Rotation- Solid Mesh Generation Using Symmetry

Mesh Part Extrusion- What is Mesh Part Extrusion- Solid Mesh Generation Using Extrusion with Translation- Solid Mesh Generation Using Extrusion with Rotation- Solid Mesh Generation Using Extrusion with Symmetry- Solid Mesh Generation Using Extrusion along Spine

Mesh Analysis and Mesh Data Transfer- Quality Analysis- Cutting Plane Analysis- Import/Export Meshes

ExercisesEx. 1: OCTREE Tetrahedron Mesher (15min) / All sectorsEx. 2: Solid Meshing Using Sweep 3D (5min) / All sectorsEx. 3: Mesh Part Transformation (15min) / All sectorsEx. 4: Mesh Part Extrusion (15min) / All sectorsEx. 5: Master Exercise: Meshing of an Engine Cylinder Block (60min) / Allsectors


AnalysisSolutions

FMS: FEM Surface

EDU-CAT-E-FMS-FCourse Code EDU-CAT-E-FMS-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMS-FI-V5R17 Foils: EDU-CAT-E-FMS-FF-V5R17 Exercises: EDU-CAT-E-FMS-FX-V5R17 Detailed Steps: EDU-CAT-E-FMS-FS-V5R17

ObjectivesDefine global mesh parameters and local specifications - Simplify model geometry and boundaries - Manage multi-domains and define welding connections- Apply mesh offsets and transformations- Check interferences and mesh quality- Import and export meshes

Participants' ProfileStructural Analysts

Prerequisites- Generative Part Structural Analysis Expert- Generative Assembly Structural Analysis- Generative Dynamic Response Analysis- ELFINI Structural Analysis

ContentThis course will teach you how to create a FE model for a complex surfacepart, and how to simplify geometric data so as to optimize the meshingprocess. You will learn how to manage surface and beam meshes, modifymeshes and node distributions, and perform interference and quality checks.

- Introduction to FEM Surface- Advanced Surface Mesh- Surface Mesh- OCTREE Triangle Mesher- Mesh Operators- Mesh Transformations- Update Mesh- Mesh Analysis Tools- Import/Export Meshes- Welding Connections- Pre-Processing Analysis Capabilities


ExercisesEx. 1: Floor Mesh (20min) / All sectorsEx. 2: Fuselage Door Static Analysis (30min) / All sectorsEx. 3: Surface Mesher (75min) / All sectorsEx. 4: Octree Mesh on Block Cylinder (15min) / All sectorsEx. 5: Hybrid Mesh: 1D and 2D (30min) / All sectorsEx. 6: Extrude 1D Element Into 2D Mesh (15min) / All sectorsEx. 7: Mesh Parameters Exposition to Knowledge (30min) / All sectorsEx. 8: Mesh Parameters Exposition to Knowledge 2 (10min) / All sectorsEx. 9: Mesh Parameters Exposition to Knowledge 3 (5min) / All sectorsEx. 10: Meshing Parametric Conceptual Body (60min) / All sectorsEx. 11: Seam Welding Analysis (60min) / All sectorsEx. 12: Compatible Seam Welds (30min) / All sectorsEx. 13: Spot Welding With Hemming (15min) / All sectorsEx. 14: Fuselage Connection (60min) / All sectorsEx. 15: Master Exercise 1: Meshing of a Crossmember (60min) / All sectorsEx. 16: Wing Structure Analysis (60min) / All sectors


AnalysisSolutions

GAS: Generative Assembly Structural Analysis

EDU-CAT-E-GAS-FCourse Code EDU-CAT-E-GAS-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GAS-FI-V5R17 Foils: EDU-CAT-E-GAS-FF-V5R17 Exercises: EDU-CAT-E-GAS-FX-V5R17 Detailed Steps: EDU-CAT-E-GAS-FS-V5R17

Objectives- Use different types of hypotheses for an assembly analysis- Define analysis connections between assembly components- Use existing assembly constraints to automatically create connections- Assign a connection property to the appropriate analysis connection- Compute a static analysis for an assembly- Create and manage an analysis assembly model from existing meshed parts


PrerequisitesGenerative Part Structural Analysis Fundamentals Generative Part Structural Analysis Expert


ContentThis course will teach you how to perform a Finite Element Analysis using anexisting assembly, and will focus on the creation of connections betweenassembly components and how to assign appropriate connection properties.You will also learn how to create an analysis assembly from existing meshedparts.

Introduction to GAS- What is Generative Assembly Structural Analysis-Assembly Analysis Overview-Analysis Assembly Overview-what is GAS-Hypotheses Used for Analysis

Analysis Connections-What is Analysis Connection-General Analysis Connection-Defining Line Analysis Connections-Defining Point Analysis Connections-Defining Surface Analysis Connections-Points to Points Analysis Connection

GAS Connections-Face Face Connection Properties-Distant Connection Properties-Welding Connection Properties-Nodes to Nodes Connection Property

Analysis Assembly Management-What is Analysis Assembly-Why Use Analysis Assembly-Analysis Assembly Process-What is Shape Representation-How to Attach Shape to Part-What is Analysis Assembly 2D Viewer-How to Use Analysis Assembly 2D Viewer

ExercisesEx. 1: Pressure Fitting connection Property (15min) / All sectorsEx. 2: Face Face Connections Property (30min) / All sectorsEx. 3: Distant Connection Property (60min) / All sectorsEx. 4: Analysis Assembly (60min) / All sectorsEx. 5: Master Exercise: Static Analysis on an Assembly: Presentation (90min) /All sectors


AnalysisSolutions

GDY: Generative Dynamic Response Analysis

EDU-CAT-E-GDY-FCourse Code EDU-CAT-E-GDY-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GDY-FI-V5R17 Foils: EDU-CAT-E-GDY-FF-V5R17 Exercises: EDU-CAT-E-GDY-FX-V5R17 Detailed Steps: EDU-CAT-E-GDY-FS-V5R17

Objectives- Recognize the differences between harmonic and transient analyses- Define load and restraint excitations- Ensure that the appropriate pre-requisites are defined for the requiredexcitation case- Visualize and animate 3D images of the analysis results- Generate translation, velocity and acceleration graphs- Export result data in Text or Excel format


PrerequisitesGenerative Part Structural Analysis Fundamentals Generative Part Structural Analysis Expert

ContentThis course will teach you how to perform a harmonic or transient analysis on asingle part using finite elements. You will learn how to generate and visualize2D graphical results and how to export the resulting data.

Introduction to GDY-What are the Different Types of Dynamic Analysis-Load or Restraint Excitation-Prerequisites

GDY Preprocessing-Harmonic Response Case-Transient Response Analysis

Results Visualization- Generating Images- Generating 2D Display

ExercisesEx. 1: Master Exercise: Transient Dynamic Analysis (60min) / All sectors


AnalysisSolutions

GPE: Generative Part Structural Analysis Expert

EDU-CAT-E-GPE-FCourse Code EDU-CAT-E-GPE-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPE-FI-V5R17 Foils: EDU-CAT-E-GPE-FF-V5R17 Exercises: EDU-CAT-E-GPE-FX-V5R17 Detailed Steps: EDU-CAT-E-GPE-FS-V5R17

Objectives- Define and customize material properties- Apply pressure, acceleration and force density loads; and define virtual parts- Apply pivot, ball-joint, and user-defined restraints- Compute a frequency analysis for a single part- Create planar sections with which to visualize internal result values- Compute and refine a mesh using adaptive meshing in order to achieve apre-defined accuracy

Participants' ProfileMechanical Designers

PrerequisitesGenerative Part Structural Analysis Fundamentals

ContentThis course will focus on advanced Finite Element Analysis pre-processingtechniques and post-processing tools, including the concept of virtual parts toavoid excessive geometric modeling. It will teach you how to perform afrequency analysis on a single part, and the use of adaptive meshing toachieve pre-defined accuracy.

GPS Advanced Pre-Processing Tools- Advanced Pre-Processing Tools- Frequency Analysis

Computation- Computing a Frequency Case- Computing with Adaptivity- Historic of Computation

GPS Advanced post-Processing Tools- Results Visualization- Results Management- Refinement

ExercisesEx. 1: Pre-Processing’ Recap Exercise (20min) / All sectorsEx. 2: Results Visualization’ Recap Exercise (10min) / All sectorsEx. 3: Master Exercise: Frequency Analysis on a Crank Shaft (30min) / Allsectors


AnalysisSolutions

GPF: Generative Part Structural AnalysisFundamentals

EDU-CAT-E-GPF-FCourse Code EDU-CAT-E-GPF-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GPF-FI-V5R17 Foils: EDU-CAT-E-GPF-FF-V5R17 Exercises: EDU-CAT-E-GPF-FX-V5R17 Detailed Steps: EDU-CAT-E-GPF-FS-V5R17

Objectives- Use Finite Element Analysis - Mesh a part with different element types and shapes, and define partproperties- Apply clamp, slider, and iso-static restraints; and force, moment anddisplacement loads- Compute a static analysis for a single part- Visualize images of the analysis results, and produce analysis reports- Refine existing meshes in order to produce more accurate results


PrerequisitesCATIA V5 Fundamentals


ContentThis course will introduce you to basic concepts of Finite Element Analysis andthe general analysis process. It will teach you how to perform a simple staticanalysis on a single part using finite elements, and how to produce a finalreport of the results.

Introduction to Finite Element Analysis- What is Finite Element Analysis- Why to Use Finite Element Analysis- Application of Finite Element Analysis

Introduction to GPS Analysis- Accessing the Generative Part Structural Analysis Workbench- The Generative Part Structural Analysis Interface- The GPS General Process- The Generative Part Structural Analysis Tree Structure

GPS Pre-Processing- Managing Mesh-Part- Defining Restraints- Defining Loads

Computation- Specifying the External Storage- Computing a Static Case

GPS Post-Processing - Results Visualization- Results Management- Refinement

Managing Analysis- About Saving an Analysis Document- About Save As- How to Use Save Management- Saving Document Using ‘Send To’ Mechanism- User Settings

ExercisesEx. 1: Pre-Processing’ Recap Exercise (10min) / All sectorsEx. 2: ‘Computation’ Recap Exercise (5min) / All sectorsEx. 3: ‘Results Visualization’ Recap Exercise (10min) / All sectorsEx. 4: ‘Results Management’ Recap Exercise (10min) / All sectorsEx. 5: ‘Refinement’ Recap Exercise (10min) / All sectorsEx. 6: Mesh Refinement with Precision : Recap Exercise (60min) / All sectorsEx. 7: Master Exercise: Static Analysis on a Hanger (50min) / All sectors


AnalysisSolutions

TAA: Tolerance Analysis of Deformable Assembly

EDU-CAT-E-TAA-FCourse Code EDU-CAT-E-TAA-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TAA-FI-V5R17 Foils: EDU-CAT-E-TAA-FF-V5R17 Exercises: EDU-CAT-E-TAA-FX-V5R17

ObjectivesIn this course, you will learn about the Tolerance Analysis of DeformableAssembly workbench and more precisely about the Process Product Resourceconcept and the main functionalities.

Participants' ProfileExperienced CATIA V5 users

PrerequisitesGenerative Shape Design (GSD)Generative Part Structural Analysis (GPS)

Content- Plates assembly Interactive Tolerance analysis- Tolerance analysis from a text file- Tolerancing and Analysis geometric variations- Sensitivity Tolerance analysis from a text file- Complete Plates assembly TAA text file creation- Interactive Tolerance analysis : Application

ExercisesEx. 1: Plates assembly Interactive Tolerance analysis (120min) / All sectorsEx. 2: Tolerance analysis from a text file (90min) / All sectorsEx. 3: Tolerancing and Analysis geometric variations (100min) / All sectorsEx. 4: Sensitivity Tolerance analysis from a text file (100min) / All sectorsEx. 5: Complete Plates Assembly text file creation (100min) / All sectorsEx. 6: Interactive Tolerance analysis : Application (480min) / Aerospace,Automotive, Shipbuilding



Equipment & Systems Engineering Solutions


Equipment & SystemsEngineering

Solutions

CBD: Circuit Board Design

EDU-CAT-E-CBD-FCourse Code EDU-CAT-E-CBD-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-CBD-FI-V5R17 Foils: EDU-CAT-E-CBD-FF-V5R17 Exercises: EDU-CAT-E-CBD-FX-V5R17 Detailed Steps: EDU-CAT-E-CBD-FS-V5R17

ObjectivesAt the end of this course, participants will be able to:- Create Printed Circuit Boards (PCB) in a context of Assemblies,- Export and import to/from an ECAD tool using the IDF interface.

Participants' ProfileElectrical designers knowing how to work with CATIA V5 Parts and Assemblies

PrerequisitesCOM-F: Getting Started with CATIA V5PDG-F: Part Design

Content- Introduction to Circuit Board Design- Creating the PCB geometry with mounting holes- Constraint areas and components- Export and Import using the IDF Interface - Creating a catalog of electrical components

ExercisesEx. 1: Transformer (45min) / Electronics & ElectricalEx. 2: Connector Box (40min) / Electronics & ElectricalEx. 3: Camera (30min) / Electronics & Electrical



Solutions

EHF: Electical Harness Flattening

EDU-CAT-E-EHF-FCourse Code EDU-CAT-E-EHF-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EHF-FI-V5R17 Foils: EDU-CAT-E-EHF-FF-V5R17 Exercises: EDU-CAT-E-EHF-FX-V5R17

ObjectivesIn this course you will learn how to flatten an electrical or geometrical harnessintegrated within the DMU and how to modify the bundle segments of theharness to fit your drawing in order to build the harness documentation

Participants' ProfileElectrical V5 users

PrerequisitesPRO-F: CATIA Tools for Proficient UsersEHI-F: Electrical Harness InstallationELB-F: Electrical Librarian

ContentIntroduction to Harness FlatteningHarness Flattening parametersExtracting dataHarness flattening modificationsSynchronizeLinks visualizationReportsDrawingCatalog text template creationGraphic Replacement

ExercisesEx. 1: Harness Documentation / Electronics & ElectricalEx. 2: Harness Flattening / Electronics & ElectricalEx. 3: Harness Documentation (2) / Electronics & ElectricalEx. 4: Harness Flattening (2) / Electronics & Electrical



Solutions

ELI: Electrical Librarian & Harness Installation

EDU-CAT-E-ELI-FCourse Code EDU-CAT-E-ELI-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ELI-FI-V5R17 Foils: EDU-CAT-E-ELI-FF-V5R17 Exercises: EDU-CAT-E-ELI-FX-V5R17

ObjectivesIn this course you will learn how to build and manage an electrical componentscatalog, to design a harness integrated within the DMU and then connect thebundle segments to electrical components.

Participants' ProfileNew Electrical V5 users

PrerequisitesCatalog Editorart DesignCATIA V5 basics (mandatory)

ContentIntroduction to Electrical LibrarianElectrical Componentas DefinitionElectrical Librarian Catalog ManagementElectrical AssembliesIntroduction to Electrical Harness InstallationElectrical Harness SettingsGeometric Bundle definitionPosition Electrical DevicesBundle segment DefinitionManaging a Branch PointDelete BranchSplit a Bundle segmentTransfer BranchesInstantiate a protectionAdjust DiameterLinks ManagementLocal slack managementSupport ManagementMeasure geometrical bundle inertiaV4/V5 MigrationWires ManagementImporting electrical external data for 3D implementation

What is new in this releaseNew course built from the V5R16 Electrical Librarian and Electrical HarnessInstallation courses


ExercisesEx. 1: Creating a catalog (10min) / All sectorsEx. 2: Defining a set of electrical components (40min) / All sectorsEx. 3: Store components in a catalog (15min) / All sectorsEx. 4: Define an assembly with the components from the catalog (15min) / AllsectorsEx. 5: Create a protection and store it into a catalog (15min) / All sectorsEx. 6: Bundle Segment Definition (15min) / All sectorsEx. 7: Create an adaptative support and position Bundle Segment (30min) / AllsectorsEx. 8: Link a bundle segment (10min) / All sectorsEx. 9: Add a Support to a Bundle Segment (5min) / All sectorsEx. 10: Add Local Slack to Bundle Segment portion (5min) / All sectorsEx. 11: Manage the bundle segment section (30min) / All sectorsEx. 12: Transfer Branches (15min) / All sectorsEx. 13: Instantiate a Protection (15min) / All sectorsEx. 14: Adjusts Diameter (10min) / All sectorsEx. 15: Split a Bundle Segment (10min) / All sectorsEx. 16: Define a Bundle Segment (20min) / All sectorsEx. 17: Harness Design / All sectorsEx. 18: Geometrical bundle inertia / All sectorsEx. 19: Knowledge (20min) / All sectorsEx. 20: External Data (30min) / All sectorsEx. 21: Electrical Harness installation / All sectorsEx. 22: Car Door / All sectors



Solutions

EWR: Electrical Wire Routing

EDU-CAT-E-EWR-FCourse Code EDU-CAT-E-EWR-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-EWR-FI-V5R17 Foils: EDU-CAT-E-EWR-FF-V5R17 Exercises: EDU-CAT-E-EWR-FX-V5R17

ObjectivesAt the end of this course, participants will be able to:- Route wires in a harness.- Route signals in space reservation system- Use knowledgeware for segregation rules

Participants' ProfileNew V5 CATIA electrical users

PrerequisitesCATIA V5 Part DesignCATIA V5 Assembly Design

ContentIntroduction to Electrical Wire RoutingImport External DataWires Management

ExercisesEx. 1: External Data Exchange (60min) / All sectorsEx. 2: External Data (60min) / All sectorsEx. 3: External Data Exchange (60min) / All sectors



Solutions

TUB: Tubing Design

EDU-CAT-E-TUB-FCourse Code EDU-CAT-E-TUB-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUB-FI-V5R17 Foils: EDU-CAT-E-TUB-FF-V5R17 Exercises: EDU-CAT-E-TUB-FX-V5R17 Detailed Steps: EDU-CAT-E-TUB-FS-V5R17

ObjectivesIn this course you will learn how the CATIA Tubing Design product is used toquickly and efficiently create an intelligent tubing layout.



Content- Introduction to Tubing Design - General Philosophy- Accessing the Workbench- User Interface- Tubing Design Fundamentals- Understanding the General Process- Selecting a Project and a Discipline- Managing Tubing Line ID’s- Routing a Tubing Run- Routing a Flexible Tubing- Routing a Tubing Bundle- Modifying a Tubing Run- Managing Spools- Placing and Modifying Parts on a Tubing Run- Managing Flow Direction- Object Navigator- Graphic Representation - Schematic Driven - Saving a Tubing Document - Generating Reports- To sum up

ExercisesEx. 1: Creating, Modifying and placing parts on a run (45min) / All sectorsEx. 2: Flexible and Bundle of Flexibles (20min) / All sectorsEx. 3: Global Exercise (60min) / All sectorsEx. 4: Generating Production Documents (15min) / All sectorsEx. 5: Schematics-Driven Design (10min) / All sectors



Solutions

TUD: Tubing Diagrams

EDU-CAT-E-TUD-FCourse Code EDU-CAT-E-TUD-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUD-FI-V5R17 Foils: EDU-CAT-E-TUD-FF-V5R17 Exercises: EDU-CAT-E-TUD-FX-V5R17 Detailed Steps: EDU-CAT-E-TUD-FS-V5R17

ObjectivesThis course illustrates how the Tubing Diagram product could be used toquickly and efficiently create a schematic diagram.

Participants' ProfileExperienced CATIA V5 Users


Content- Starting a Tubing Diagram - Diagram Creation- Zone Creation and Management - Diagram Modification/Annotation/Reports- Design Checks- Network Analysis- Object Navigator- to sum up

ExercisesEx. 1: Tubing Diagrams Fundamental (Master Exercise) (60min) / All sectors



Solutions

TUS: Tubing Catalogs (2D Diagrams & 3D Design)

EDU-CAT-E-TUS-ACourse Code EDU-CAT-E-TUS-ACATIA V5R17Brand & Release CATIA V5R174 daysDuration 4 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TUS-AI-V5R17 Foils: EDU-CAT-E-TUS-AF-V5R17 Exercises: EDU-CAT-E-TUS-AX-V5R17 Detailed Steps: EDU-CAT-E-TUS-AS-V5R17

ObjectivesThis courseware is designed to teach Tubing specialists and administratorshow to define 2D (schematic diagrams) & 3D Tubing catalogs andspecifications.

Participants' Profile2D & 3D Catalog designers and administrators for Equipment & Systems andwho are experienced CATIA V5 users.

PrerequisitesTubing DiagramsTubing DesignGeneric Routing

ContentDefinitions General Philosophy – Feature Concept General Philosophy – Catalogs General Philosophy – Rules and Attributes Understanding the General Process Global Customization ProcessTubing Workbench Customization Project Resource Management Feature Dictionary 2D Diagrams Catalogs Creation Standards Catalog Design Rules Catalog Building Tubing Parts Creating a New Tubing Part Building a Bendable Tube Creating a Tubing Parts Catalog (Master) Placing Parts From the Tubing Parts Catalog Setting up Specifications Catalog Placing Parts From the Specifications CatalogCreating a Report Generating a Report From a Macro – First Solution Defining and Generating a customized Report – Second Solution

Drawing Production SettingsTo Sum up

ExercisesEx. 1: Creating a Tubing Catalog (360min) / All sectorsEx. 2: Creating a 2D Diagram Catalog (140min) / All sectors



Infrastructure Solutions


InfrastructureSolutions

ADM: V5 Administration

EDU-CAT-E-ADM-FCourse Code EDU-CAT-E-ADM-FCATIA V5R17Brand & Release CATIA V5R173 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ADM-FI-V5R17 Foils: EDU-CAT-E-ADM-FF-V5R17 Exercises: EDU-CAT-E-ADM-FX-V5R17

ObjectivesAt the end of this course, administrators will know how to install, customize andmaintain CATIA V5.They will study many issues about CATIA infrastructure, administration anddata management.

Participants' ProfileThis class is for Unix & Windows NT System Administrators andCATIA/ENOVIA key application & support engineers.

PrerequisitesUnix AdministrationNT Administration

Content- Installing CATIA V5 on NT and on Unix with documentation- Looking at Licensing system and configurations- License management on NT and Unix- CATIA V5 environments and related variables- Customized installations and users settings- Administrating settings with VB macros - Lock and set default settings by administrator/root- Organize CATIA data with DLNames- Customizing general and drafting standards- Upgrading from CATIA V5 service packs approach- Procedures for automatic installation checking on NT and Unix- Distributing CATIA on NT and Unix clients - A view of various batch tools- Reviewing Data and links management aspects - Over viewing of UNIX/Windows and V4/V5 interoperability

ExercisesEx. 1: Installing CATIA V5 on NT (30min) / All sectorsEx. 2: Checking, configuring licenses (10min) / All sectorsEx. 3: Customizing an environment (20min) / All sectorsEx. 4: Settings (60min) / All sectorsEx. 5: Customizing standards (15min) / All sectorsEx. 6: Installing a service pack, Distributing CATIA V5 to client from server onNT, checking the installation (60min) / All sectorsEx. 7: Practicing with tools (30min) / All sectorsEx. 8: Understanding Document environment anf links (60min) / All sectorsEx. 9: Interoperability cases (15min) / All sectors



PRO: CATIA Tools for Proficient Users

EDU-CAT-E-PRO-FCourse Code EDU-CAT-E-PRO-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PRO-FI-V5R17 Foils: EDU-CAT-E-PRO-FF-V5R17

Objectives- Create and manage component catalogs- Find and insert components from catalogs- Create and save Powercopies- Use Powercopies to create new features- Transfer a CATIA V4 model to CATIA V5


PrerequisitesCATIA V5 Fundamentals, Part Design

ContentThis course will teach you how to use advanced CATIA tools to re-use existingCATIA V4 and CATIA V5 model data. You will learn how to make use ofcomponent catalogs, and how to store and create re-usable parameterizedfeatures.

- Creating and Using Powercopies- Creating Catalogs of Components- From CATIA V4 to V5 Basics

ExercisesEx. 1: Creating a PowerCopy (20min) / All sectorsEx. 2: Instantiating a PowerCopy (10min) / All sectorsEx. 3: Creating a Catalog from a CATDrawing file (15min) / All sectorsEx. 4: Adding a Chapter to a Catalog (10min) / All sectorsEx. 5: Adding a Family (10min) / All sectorsEx. 6: Creating a Keyword in a Catalog (10min) / All sectorsEx. 7: Adding a Component (10min) / All sectorsEx. 8: Copying a CATIA V4 Solid into CATIA V5 (10min) / All sectors



V4A: V4/V5 Advanced Interoperability

EDU-CAT-E-V4A-ACourse Code EDU-CAT-E-V4A-ACATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V4A-AI-V5R17 Foils: EDU-CAT-E-V4A-AF-V5R17 Exercises: EDU-CAT-E-V4A-AX-V5R17

ObjectivesIn this course, you will learn advanced interoperability concepts about themigration of CATIA V4 geometric/application data to CATIA V5. You will alsolearn how V5 data can be saved in CATIA V4 formats or used directly in CATIAV4.

Participants' ProfileExperienced CATIA V4/V5 users

PrerequisitesBasic knowledge of CATIA V5 Mechanical Design Solutions

Content- From V4 to V5 - Transfer of V4 geometric data to V5 - Transfer of V4 application data to V5- From V5 to V4 - Using V5 data in V4 - Saving V5 data in V4 formats

ExercisesEx. 1: Smart/Unsmart Solid (15min) / All sectorsEx. 2: Error during update (15min) / All sectorsEx. 3: Migration of kinematics data (25min) / All sectorsEx. 4: Sheet Metal Design (10min) / All sectors



V4I: V4 Integration

EDU-CAT-E-V4I-FCourse Code EDU-CAT-E-V4I-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V4I-FI-V5R17 Foils: EDU-CAT-E-V4I-FF-V5R17 Exercises: EDU-CAT-E-V4I-FX-V5R17 Detailed Steps: EDU-CAT-E-V4I-FS-V5R17 Demonstration: EDU-CAT-E-V4I-FD-V5R17

ObjectivesAt the end of this course, participants will be able to:- Use CATIA V4 data in CATIA V5- Transfer a CATIA V4 solid into a CATIA V5 CATPart- Manage the links between CATIA V4 and CATIA V5 documents

Participants' ProfileCATIA V5 users

PrerequisitesBasic knowledge of CATIA V5 Mechanical Design Solutions

Content- Introduction to V4 Integration- Creating a CATProduct using V4 data- Assembly of V4 data in a V5 CATProduct- Transferring V4 data into V5 CATPart- Design in context- Drawing of a V4/V5 document in V5- Migration of 2D Draw elements and Views- CATIA V5 DMU solutions and V4 data- Links between V4 data and V5 documents

ExercisesEx. 1: Recap Exercise 1 : open and check the V4 geometry (20min) / AllsectorsEx. 2: Recap Exercise 2 : Solid translation (15min) / All sectorsEx. 3: Recap Exercise 3 : manipulations in a CATProduct (20min) / All sectorsEx. 4: Welding Gun : Creating a CATProduct with V4 data (10min) / All sectorsEx. 5: Welding Gun : Assembly of V4 data in a V5 CATProduct (15min) / AllsectorsEx. 6: Welding Gun : Copy/Pasting a V4 solid in a V5 CATPart (20min) / AllsectorsEx. 7: Welding Gun : Design in context (20min) / All sectorsEx. 8: Welding Gun : Generative drafting (20min) / All sectorsEx. 9: Welding Gun : DMU Space Analysis (20min) / All sectorsEx. 10: Welding Gun : V4 Modification and Update in V5 (20min) / All sectors



VBA: CATIA V5 Automation

EDU-CAT-E-VBA-FCourse Code EDU-CAT-E-VBA-FCATIA V5R17Brand & Release CATIA V5R173 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-VBA-FI-V5R17 Foils: EDU-CAT-E-VBA-FF-V5R17 Exercises: EDU-CAT-E-VBA-FX-V5R17

ObjectivesAt the end of this course, participants will have a good understanding of thedifferent ways to automate tasks related to CATIA V5: CATIA Macros andVisual Basic Programming.

Participants' ProfileCATIA V5 Applications developers; bench markers

PrerequisitesCATIA V5 Fundamentals.Visual Basic Editor on PC NTMinimum knowledge or exposure to Microsoft Visual Basic (cf. book ref.Microsoft Visual Basic 6.0 Learning Edition)JavaScript is a plus

Content- CATIA V5 OLE Automation, Journaling & Scripting Architecture- Exported objects of CATIA V5- Designing panels for Macros- Graphic selection of objects- Settings - V5 Administration - Communication with another Automation server.

ExercisesEx. 1: Cylinders (Master Exercise) (10min) / All sectorsEx. 2: Modifying the viewpoint of an existing document (30min) / All sectorsEx. 3: Creating 2D sketch with constraints (15min) / All sectorsEx. 4: Creating part design features (30min) / All sectorsEx. 5: Creating 3D wireframes and 3D surfaces (30min) / All sectorsEx. 6: Titanic (30min) / All sectorsEx. 7: Drafting the bolt (30min) / All sectorsEx. 8: Test Selections (30min) / All sectorsEx. 9: Select Element (30min) / All sectorsEx. 10: Get Point (30min) / All sectorsEx. 11: Settings - Applying local changes (20min) / All sectors



Mechanical Design Solutions


Mechanical DesignSolutions

ASL: Aerospace Sheet Metal Design

EDU-CAT-E-ASL-FCourse Code EDU-CAT-E-ASL-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ASL-FI-V5R17 Foils: EDU-CAT-E-ASL-FF-V5R17 Exercises: EDU-CAT-E-ASL-FX-V5R17 Detailed Steps: EDU-CAT-E-ASL-FS-V5R17

ObjectivesIn this course, you will learn how to generate sheet metal parts for aerospace

Participants' ProfileAerospace Airframe Designer

PrerequisitesPart Design, Assembly Design, Wireframe and Surface Design

Content- Introduction to Aerospace Sheet Metal Design- ASL Parameters- Creating the Web- Creating a Surfacic Flange- Creating a Joggle- Creating Flanges- Creating a Corner Relief - Creating a Cut Out- Creating Stamps - Flanged Hole - Bead - Circular Stamp - Surface Stamp - Flanged Cutout - Stiffening Rib - Curve Stamp - User Stamp- Creating a Hole- Points or Curves Mapping- Creating Corners or Chamfers- Applying a Pattern- Modifying a Feature- Generating Folded and Flattened Parts- Drawing Generation

ExercisesEx. 1: Fighter Airframe (50min) / All sectorsEx. 2: Aero Structure (30min) / All sectorsEx. 3: Bracket (15min) / All sectorsEx. 4: Fighter Web Structure (20min) / All sectorsEx. 5: Rib (20min) / All sectors



ASM: CATIA Product Design Expert

EDU-CAT-E-ASM-ACourse Code EDU-CAT-E-ASM-ACATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-ASM-AI-V5R17 Foils: EDU-CAT-E-ASM-AF-V5R17 Exercises: EDU-CAT-E-ASM-AX-V5R17 Detailed Steps: EDU-CAT-E-ASM-AS-V5R17

ObjectivesModify CATIA options in order to optimize performance for large, complexdesignsManage contextual links between product documents by using publicationsCreate and use parameters to drive a product designCreate sections to visualize internal product structureCreate scenes and exploded viewsGenerate annotations and bills of material for assembly drawings

Participants' ProfileAdvanced Users

PrerequisitesCATIA Product Design, CATIA Part Design

ContentThis course will teach you collaborative engineering methods with which youcan design parts in the context of a complex product structure. You will learnhow to optimize performance for large and complex designs, and how togenerate annotations and bills of material for assembly drawings.

- Managing a Product Structure- Designing & Managing Contextual Parts- Creating and Using Published Geometry- Flexible Sub-Assembly- Working with Large Assemblies- Analyzing Assemblies to Prepare drawing

ExercisesEx. 1: Assembly Design Settings (30min) / All sectorsEx. 2: Connector Assembly - Assembling Components (15min) / All sectorsEx. 3: Connector Assembly - Positioning Components (20min) / All sectorsEx. 4: Connector Assembly - Analyzing the Assembly (15min) / All sectorsEx. 5: Connector Assembly - Fixing the clash (30min) / All sectorsEx. 6: Connector Assembly - Adding screws (10min) / All sectorsEx. 7: Vice Assembly - Creating the Structure (15min) / All sectorsEx. 8: Vice Assembly - Positioning Components (20min) / All sectorsEx. 9: Vice Assembly - Editing parts (20min) / All sectorsEx. 10: Vice Assembly - Inserting Fitting Components (15min) / All sectorsEx. 11: Flexible Assemblies : Assembling Components (3min) / All sectorsEx. 12: Flexible Assemblies : Constrain Clamp Assembly (15min) / All sectorsEx. 13: Flexible Assemblies : Change configuration (7min) / All sectors



CCV: Core & Cavity Design

EDU-CAT-E-CCV-FCourse Code EDU-CAT-E-CCV-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-CCV-FI-V5R17 Foils: EDU-CAT-E-CCV-FF-V5R17 Exercises: EDU-CAT-E-CCV-FX-V5R17 Detailed Steps: EDU-CAT-E-CCV-FS-V5R17

ObjectivesIn this course you will learn how to use workbench Core & Cavity Design tocreate the Core and Cavity sides of a part, including sliders and loose cores,required for the design of a plastic injection mold.You will also learn how to handle design changes by comparing versions of asame part.

Participants' ProfileSurface designers in tooling domain

PrerequisitesV5F-F: CATIA V5 Fundamentals

Content- Import the Part to mold- Define the Main Pulling Direction- Define a Slider/Lifter Pulling Direction- Work on Mold Areas : Transfer, Aggregate, Split, Explode, Bounding Box- Define Parting Surface- Comparing two parts

ExercisesEx. 1: Pan Handle (60min) / All sectorsEx. 2: Support (30min) / All sectors



DDR: CATIA Detail Drafting

EDU-CAT-E-DDR-FCourse Code EDU-CAT-E-DDR-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DDR-FI-V5R17 Foils: EDU-CAT-E-DDR-FF-V5R17 Exercises: EDU-CAT-E-DDR-FX-V5R17 Detailed Steps: EDU-CAT-E-DDR-FS-V5R17

ObjectivesThis course focuses on the tools of the drafting workbench dedicated to thecreation of interactive views. You will also learn advanced tools to dress-upand annotate the views and will be introduced to the drafting workbenchcustomization.

Upon completion of this course, you will be able to:- Create an interactive view and draw a sketch on it- Insert annotations to dress-up the views- Instantiate 2D elements from catalogs- Manage the views and sheet layoutYou will also be introduced to the drafting workbench customization

Participants' ProfileDraftsmen

PrerequisitesStudents attending this course should be familiar with the basics of 2D viewscreation in CATIA V5

GDRI: Generative Drafting (ISO) (EDU-CAT-E-GDRI-F - V5R17)GDRA: Generative Drafting (ANSI) (EDU-CAT-E-GDRA-F - V5R17)

Content- Introduction to drafting workbench- Creating Interactive Views- Dressing up the Layout- View and Sheet Management- Customizing the Drafting Workbench

What is new in this releaseThis course has been reworked to focus on the interactive creation and dressup of views. It includes useful recommendations and introduces to the use of2D components from catalogs.

ExercisesEx. 1: Adding Drawing Views (45min) / All sectorsEx. 2: Adding Annotations (30min) / All sectorsEx. 3: Car Jack Support (30min) / All sectorsEx. 4: Master Exercise 1 (60min) / All sectors



DRA: Advanced Drafting & Customization

EDU-CAT-E-DRA-ACourse Code EDU-CAT-E-DRA-ACATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DRA-AI-V5R17 Foils: EDU-CAT-E-DRA-AF-V5R17 Exercises: EDU-CAT-E-DRA-AX-V5R17

ObjectivesIn this class, participants will Benefit from hints and tips on-Interactive drafting- Large assembly drawings-Dimension generation from 3D definitions of parts -Learn how to define standards and re-use existing start-up drawings-Build frames, title & revision blocks from table values with VBScript support

The will also learn how to manage drafting standard files.

Participants' ProfileExperienced drafters

PrerequisitesV5F: CATIA V5 Fundamentals (EDU-CAT-E-V5F-F - V5R16)

ContentDuring this 2-day session you will see •Detail review of CATIA drafting tools available in: •DR1: CATIA Drafting 1 Configuration•DP2: CATIA Drawing Production 2 Configuration•Defining Company Drawing Standards (production set)•Setting drawing formats, symbols, start up drawings patterns according to aCompany or project standards•Setting and controlling Standard files Applications•Reusing an existing start-up drawings•For a generative drawing:•Advanced filtering techniques (multi-selection of nodes and attributes ofviews)•Auto-dimensioning and balloons creation•Defining drawing formats (frame) and title block information (with and withoutmacros)•Integrating table values or revision information•Customizing with VBScript•Creating tolerance tables (automation) and managing ditto •Recommended Methodologies for ID1,•Hints and Tips, annotation and dress up tools (dimensions standards, textstandards, FD&T standards, center line with and without reference, etc…)

ExercisesEx. 1: The Plate (45min) / All sectorsEx. 2: The Pivot (45min) / All sectorsEx. 3: Generating Dimensions (25min) / All sectorsEx. 4: Using filtering techniques (25min) / All sectorsEx. 5: Geometry & Free Text in VB Script (15min) / All sectorsEx. 6: Fill in Title Block (20min) / All sectors



FMP: Functional Molded Part

EDU-CAT-E-FMP-FCourse Code EDU-CAT-E-FMP-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FMP-FI-V5R17 Foils: EDU-CAT-E-FMP-FF-V5R17 Exercises: EDU-CAT-E-FMP-FX-V5R17

ObjectivesUpon Completion of this course you will be able to:- Define the main shapes of a molded part as added or removed material- Add functional features such as ribs or cutouts to the part- Finalize the molded part using the feature modifiers such as fillets or patterns- Use the multi-body approach- Extract cores and cavities from the final part

Participants' ProfileMold Designers

PrerequisitesStudents attending this course should be familiar with the basics of solids andsurfaces creation

ContentThis course will teach you how to use the Functional Molded Part workbench tocreate molded parts from the main shapes definition and to finalize the partwith additional dress up features. You will also be taught the multi-bodyapproach and will finally learn how to extract cores and cavity from the finalpart.

- Introduction- Shape Features- Mold Design properties- Functional Features- Feature Modifiers- Dress up Features- Functional Extration - Design Process

What is new in this release- Recap exercises- Assessments- Simulations

ExercisesEx. 1: Locking cover (45min) / All sectorsEx. 2: Belt Housing (60min) / All sectorsEx. 3: Electrical box housing (60min) / All sectorsEx. 4: Notepad (30min) / All sectorsEx. 5: Functional mold extraction Electrical box housing (25min) / All sectors



FR1: Part Design Feature Recognition

EDU-CAT-E-FR1-FCourse Code EDU-CAT-E-FR1-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FR1-FI-V5R17 Foils: EDU-CAT-E-FR1-FF-V5R17 Exercises: EDU-CAT-E-FR1-FX-V5R17

ObjectivesThis course aims at introducing the Feature Recognition capability, which ispart of the Part Design workbench. The exercise shows how to perform aFeature Recognition operation.

Participants' ProfileDesigners

PrerequisitesPart Design

ContentWhat is “Feature Recognition” ?Accessing the Workbench Part Analysis ToolHow to perform a FR ?Feature Recognition PanelExamplesTips

ExercisesEx. 1: Creating V5 geometry from an isolated solid (30min) / All sectors



FTA: 3D Functional Tolerancing & Annotation

EDU-CAT-E-FTA-FCourse Code EDU-CAT-E-FTA-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FTA-FI-V5R17 Foils: EDU-CAT-E-FTA-FF-V5R17 Exercises: EDU-CAT-E-FTA-FX-V5R17

ObjectivesUpon Completion of this course you will be able to:- Add 3D annotations to a part- Manage and position these annotations- Create and manage annotation planes and views- Manage the 3D geometry associated to the 3D annotations


PrerequisitesStudents attending this course should be familiar with the basics of solids andsurfaces creation and also with the basics of knowledge

ContentThis course will teach you how to create annotation planes in a CATPart andhow to add and manage 3D annotations on these planes. You will also learnhow to create 3D views in the CATPart and how to use them to create 2Dviews in a CATDrawing.

What is new in this releaseThis is now a web-based Companion course.

ExercisesEx. 1: Create and Manage 3D Annotations (65min) / All sectorsEx. 2: Create Drawings & Manage Annotations (80min) / All sectorsEx. 3: Create Assembly Annotations (25min) / All sectorsEx. 4: Modify Geometry & Update Annotations (85min) / All sectorsEx. 5: Advanced FT&A Functions (55min) / All sectorsEx. 6: Knowledge and 3D Annotations (45min) / All sectors



GS1: CATIA Surface Design

EDU-CAT-E-GS1-FCourse Code EDU-CAT-E-GS1-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GS1-FI-V5R17 Foils: EDU-CAT-E-GS1-FF-V5R17 Exercises: EDU-CAT-E-GS1-FX-V5R17 Detailed Steps: EDU-CAT-E-GS1-FS-V5R17

ObjectivesUpon completion of this course you will be able to:- Identify and use the tools specific to the Generative Shape Design workbench- Create simple reference and Wireframe geometry- Use the reference wireframe elements to create simple surfaces- Create clean topology from a set of surfaces and smooth sharp edges- Detect and correct the discontinuities on curves and surfaces- Create solids from surfaces

Participants' ProfileMechanical Surface Designers

PrerequisitesStudents attending this course should be familiar with the CATIA V5 interface

ContentThis course introduces you to the Generative Shape Design interface andbasic tools. You will be taught wireframe and surface creation and you will familiarizeyourself with the hybrid design. This course focus on the Generative Shape Design tools that are available witha MD2 license.

- Introduction to Surface Design- Creating Wireframe Geometry- Shape Design Common Tools- Creating Basic Surfaces- Performing Operations on the Geometry- Completing the Geometry in Part Design- Modifying the Geometry- Using Tools


ExercisesEx. 1: Creating Wireframe Geometry : Button (10min) / All sectorsEx. 2: Creating Wireframe Geometry : Mouse (15min) / All sectorsEx. 3: Creating Basic Surfaces : Button (5min) / All sectorsEx. 4: Creating Basic Surfaces : Mouse (15min) / All sectorsEx. 5: Operations on Geometry : Mouse (10min) / All sectorsEx. 6: Performing Operations on Geometry : Torch (30min) / All sectorsEx. 7: Completing the Solid in Part Design : Button (10min) / All sectorsEx. 8: Completing the Solid in Part Design : Mouse (30min) / All sectorsEx. 9: Modifying the Geometry : Button (10min) / All sectorsEx. 10: Modifying the Geometry : Mouse (10min) / All sectorsEx. 11: Using Tools : Surface Check Exercise (10min) / All sectorsEx. 12: Mobile Phone (1): Creating Wireframe Geometry (15min) / Electronics& ElectricalEx. 13: Mobile Phone (2): Creating Basic Surfaces (20min) / Electronics &ElectricalEx. 14: Mobile Phone (3): Join and Trim the Surfaces (15min) / Electronics &ElectricalEx. 15: Mobile Phone (4): Create the Part Geometry (10min) / Electronics &ElectricalEx. 16: Mobile Phone (5): Modify the Geometry (5min) / Electronics & Electrical



HA1: Healing Assistant

EDU-CAT-E-HA1-FCourse Code EDU-CAT-E-HA1-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-HA1-FI-V5R17 Foils: EDU-CAT-E-HA1-FF-V5R17 Exercises: EDU-CAT-E-HA1-FX-V5R17

ObjectivesIn this course, you will learn how to create valid closed topologies fromimported data, even inaccurate or invalid. The objective is to get suitable datafor further processing in V5 (example: tooling design).The course includes both theoretical descriptions and practical tips.

Participants' ProfileAll designers, especially in the tooling design domain

PrerequisitesGS1-F-V5R16: CATIA Surface Design

Content- Introduction- Workbench presentation- Model Analysis- Closing a Join surface- Comparing models

What is new in this releaseUpdates due to modification of Join command+ reorganization of manuals (fewer chapters, fewer exercise steps, ...)

ExercisesEx. 1: Lateral Fender (master exercise) (60min) / All sectorsEx. 2: Compare exercise: Lateral fender (30min) / All sectorsEx. 3: Additional exercise (Handle) (45min) / All sectors



LO1: 2D Layout for 3D Design

EDU-CAT-E-LO1-FCourse Code EDU-CAT-E-LO1-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-LO1-FI-V5R17 Foils: EDU-CAT-E-LO1-FF-V5R17 Exercises: EDU-CAT-E-LO1-FX-V5R17

ObjectivesIn this course you will learn how to draw benefit from 2D & 3D available in asingle environment to design 3D products.


PrerequisitesDraftingPart DesignAssembly Design

Content1- Introduction Accessing the Workbench User Interface General Presentation User Settings Standards2- Geometry Creation Creating Projection Views Exporting the 2D View to 2D Layout Using 2D Components 3D Visualization and Use-Edges Capabilities Managing the Background Visualization Dressing-up the Geometry Creating 3D geometry from 2D geometry3- Data Management Print Capabilities Drawing Creation from 2D Layout

ExercisesEx. 1: Front rear sprocket creation (20min) / All sectorsEx. 2: Front fork creation (60min) / All sectorsEx. 3: Tire assembly modification and CATDrawing extraction (60min) / Allsectors



MD2: Mechanical Design V5R17 Update

EDU-CAT-E-MD2-UCourse Code EDU-CAT-E-MD2-UCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishUpdateLevel UpdateCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MD2-UI-V5R17 Foils: EDU-CAT-E-MD2-UF-V5R17

ObjectivesIn this course, you will learn about the enhancements in the Mechanical DesignWorkbenches in V5R17 Release.

Following are some of the important enhancements :

- Identify the principle new mechanical design tools- Use the new options available for Variable Radius Fillet and Rib/Slot- Create symmetric set and axis systems in addition to part bodies- Create tolerant blends using new smoothing parameters- Create new 2D and 3D clipping views, add associative 2D dress-upproperties, and customize symbols

Participants' ProfileCATIA V5R15 Mechanical Designers

PrerequisitesCATIA Mechanical Design Courses

ContentThis course will teach you the principal new tools available in CATIA V5R17Mechanical Design. You will be taught the new options for variable radiuscreation. You will also learn how to create symmetric set in products, how touse tolerant modeling while creating blends. In the drafting workbench, you willsee how to create new 2D and 3D clipping views or how to customize symbols.

- Variable Radius Fillet and Rib/Slot- Symmetric set and axis systems- Tolerant blends - 2D and 3D clipping views- Associative 2D dress-up properties- Symbol customization

What is new in this releaseNew R17 Courses

ExercisesEx. 1: Create Technological Results (15min) / All sectorsEx. 2: Practice Re-route Publications (10min) / All sectorsEx. 3: Applying various 2D Visualization Mode (5min) / All sectorsEx. 4: Create an Extract sub-element of a curve (5min) / All sectors



MTD: Mold Tooling Design

EDU-CAT-E-MTD-FCourse Code EDU-CAT-E-MTD-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MTD-FI-V5R17 Foils: EDU-CAT-E-MTD-FF-V5R17 Exercises: EDU-CAT-E-MTD-FX-V5R17 Detailed Steps: EDU-CAT-E-MTD-FS-V5R17

ObjectivesIn this course, you will learn how to use the workbench Mold Tooling Design tocreate a Plastic Injection Mold

Participants' ProfileNew Mold Tooling Design users

PrerequisitesTG1: Tooling Design (EDU-CAT-E-TG1-F - V5R16)

ContentIntroduction to Mold Tooling DesignCreating a New MoldEditing the Mold BaseAdvanced Mold Base : Inserts / Stripper PlateTooling Components : Generic/MoldCreating Componentsmanaging ComponentsUser ComponentsAssembly DrillingsAdvanced Add/Remove CapabilitiesMold Design to ManufacturingCreating Injection FeaturesAnalyzing Contextual Links in the Assembly StructureCustomizing the Bill of Material of a MoldWorking with Large Assemblies : Cache Management

ExercisesEx. 1: Phone Handset (240min) / All sectorsEx. 2: Cover (180min) / All sectors



PDG: CATIA Part Design Expert

EDU-CAT-E-PDG-ACourse Code EDU-CAT-E-PDG-ACATIA V5R17Brand & Release CATIA V5R171.5 daysDuration 1.5 daysEnglishLanguage EnglishAdvancedLevel AdvancedCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PDG-AI-V5R17 Foils: EDU-CAT-E-PDG-AF-V5R17 Exercises: EDU-CAT-E-PDG-AX-V5R17 Detailed Steps: EDU-CAT-E-PDG-AS-V5R17

ObjectivesCreate and modify stable designs by using 3D reference elementsCreate advanced 3D solid features based on 2D sketchesDesign complex manufacturable solids by using advanced dress-up features Incorporate Boolean operations by using multi-body methodsShare geometric data and work collaboratively with other designersAnalyse and annotate your designs

Participants' ProfileCATIA V5 Mechanical Designers.

PrerequisitesCATIA V5 Fundamentals, Getting started with CATIA V5, Sketcher, PartDesign, Product Design, Generative Drafting (ISO or ANSI).

ContentThis course will teach you to design ‘Complex’ 3D mechanical parts fromsketches in context of an assembly. You will build upon the knowledge gainedin the Part Design Course and will be equiped to use ‘Advanced’ featuresoffered by the Part Design workbench.

- Using 3D Elements to Create a Part- Sketch-Based Features- Part Manipulations- Dress-Up Features- Part Analysis- Annotations

ExercisesEx. 1: Sketch based Features Recap Exercises (45min) / All sectorsEx. 2: Meat Mincer Screw (45min) / All sectorsEx. 3: Using 3D Elements to Create a Part Recap Exercises (35min) / AllsectorsEx. 4: Hinge (40min) / All sectorsEx. 5: Dress Up Features (35min) / All sectorsEx. 6: Part Manipulations (35min) / All sectorsEx. 7: Part Analysis (25min) / All sectorsEx. 8: Master Exercise: Mobile Phone Bottom Case (90min) / All sectors



SMD: CATIA Generative Sheet Metal Design

EDU-CAT-E-SMD-FCourse Code EDU-CAT-E-SMD-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMD-FI-V5R17 Foils: EDU-CAT-E-SMD-FF-V5R17 Exercises: EDU-CAT-E-SMD-FX-V5R17 Detailed Steps: EDU-CAT-E-SMD-FS-V5R17

ObjectivesUnderstand the terminology and the creation process for sheet metal partdesignDefine and manage sheet metal part parametersDesign walls, bends and flanges- Add features such as cutouts, holes, corners and chamfers - Create standard and user defined stamped features- Manage folded and unfolded views and export a finished flat pattern

Participants' ProfileMechanical Designers, Sheetmetal Designers

PrerequisitesCATIA V5 Fundamentals.


ContentThis course will teach you how to design a sheet metal part using associativefeature-based modeling. Standard and user defined stamped features can beintegrated into the design and the resulting flat pattern is calculated inaccordance with standard bend allowances or with company specific bendallowance tables.

Getting Started- Introduction to Sheet Metal Design- Generative Sheet Metal Design Overview- Defining Sheet Metal Parameters- Recommendations for Getting Started- Sheet Metal Walls

What is a Sheet Metal Wall?- Defining the First Wall- Secondary Walls- Part Recognition- Recommendations for Sheet Metal Walls

Bends and Unfolded Mode- Bends- Unfolded Mode- Corner Relief- Recommendations for Bends

Flanges- Creating Flanges- Recommendations for Flanges

Sheet Metal Features- Cutouts- Holes- Corners and Chamfers- Standard Stamps- User-Defined Stamps- Recommendations for Sheet Metal Features

Duplication - Patterns- Mirror- PowerCopies- Recommendations for Duplication

Mapping and Output- Point or Curve Mapping- Output

Advanced Topics in Sheet Metal- Sheet Metal Standard Files- Multi-Body Methodology

What is new in this releaseWall on edge new optionNew UI for recognitionNew treatment of stamp faceCorner relief behaviorMirroring of part body


ExercisesEx. 1: Sheet Metal Walls (45min) / All sectorsEx. 2: Bends and Unfolded Mode (30min) / All sectorsEx. 3: Flanges Exercises (30min) / All sectorsEx. 4: Sheet Metal Features (40min) / All sectorsEx. 5: Duplication (55min) / All sectorsEx. 6: Part Modifications (20min) / All sectorsEx. 7: Mapping and Output (35min) / All sectorsEx. 8: Master Exercise: Casing Assembly (80min) / All sectorsEx. 9: Multi-Body Cover (45min) / All sectors



SMD: CATIA Generative Sheet Metal Design V5R17Update

EDU-CAT-E-SMD-UCourse Code EDU-CAT-E-SMD-UCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishUpdateLevel UpdateILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMD-UI-V5R17 Foils: EDU-CAT-E-SMD-UF-V5R17

ObjectivesIn this course, you will learn about the new and enhanced capabilities of theV5R17 Generative Sheetmetal Design workbench.

Participants' ProfileMechanical Designers, Sheetmetal Designers

PrerequisitesCATIA Generative Sheetmetal Design

ContentEnhancements in Sheetmetal StampsEnhancements in Flanged HoleCreating a Flanged Hole with Flat Diameter Option

What is new in this releaseNew R17 Courses

ExercisesEx. 1: Creating a Flanged Hole with Different Options (10min) / All sectors



SR1: Structure Design

EDU-CAT-E-SR1-FCourse Code EDU-CAT-E-SR1-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SR1-FI-V5R17 Foils: EDU-CAT-E-SR1-FF-V5R17 Exercises: EDU-CAT-E-SR1-FX-V5R17 Additional Information: EDU-CAT-E-SR1-FO-V5R17

ObjectivesIn this course you will learn methods to quickly create and modify linear andcurved structures, and plates using standard or user-defined sections. Itaddresses any kind of Frames, Foundations and Steel construction …, invarious domains like Aerospace, Automotive and F&A.

Participants' ProfileNew CATIA V5 users

PrerequisitesCOM, WFS, PDG


Content1.Introduction to Structure Designp6 Accessing the Workbench p7 Exploring the User Interfacep8 Terminologyp92.Options & Project Resources Managementp10 Setting Structure Design Optionsp11 Setting Part Design Options p12 Setting Assembly Design Optionsp14 Selecting a Projectp153.Creating Skeletonsp17 What about Skeletons?p18 Creating Grids in 3Dp194.Defining and Creating Shapes & Platesp22 What about Shapes? p23 Generating Piece Parts p24 Defining & Placing Shapes… p26 Defining Material & Gradep27 Defining Section p28 Defining Shape Anchor Point p29 Defining Shape Orientation p30 Placing Shapes Using Points p31 Placing Shapes on Support p34 Creating Plates & End-Platesp36 Creating Small Assemblies p425.Modifying Shapes & Platesp44 Modifying Shapes & Plates Definition p45 Extending and Stretching Shapesp47 Splitting and Merging Shapes & Platesp48 Nibbling/Coping Shapes ans Platesp49 Defining Cutbacks p51 Removing Cutbacks p57 Placing Cutoutsp58 Modifying Cutouts p63 Removing Cutouts p64 Placing End Cuts p65 Modifying and Removing End Cuts p69 Placing Slotsp70 Modifying Slotsp74 Removing Slotsp75

What is new in this releaseAdditional exercise to handle the generation of "Piece Parts"

ExercisesEx. 1: Select your project and options (15min) / All sectorsEx. 2: External Turret: Panel System (45min) / All sectorsEx. 3: External Turret: Jacket System (30min) / All sectorsEx. 4: External Turret: Floor System (30min) / All sectorsEx. 5: External Turret: Detailing (90min) / All sectorsEx. 6: External Turret: Modifications (15min) / All sectorsEx. 7: External Turret: Secondary Structures (30min) / All sectorsEx. 8: Piece Part Generation (30min) / All sectors



SRA: Structure Design Administration

EDU-CAT-E-SRA-ACourse Code EDU-CAT-E-SRA-ACATIA V5R17Brand & Release CATIA V5R174 daysDuration 4 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SRA-AI-V5R17 Foils: EDU-CAT-E-SRA-AF-V5R17 Exercises: EDU-CAT-E-SRA-AX-V5R17 Additional Information: EDU-CAT-E-SRA-AO-V5R17

ObjectivesIn this course you will learn methods to:- administrate a SR1 project.- Create or modify a Section Catalog- Create End-Cuts, Slots and Small Assmblies


PrerequisitesCOM, WFS, PDG, SR1, PKT, KWA (Optional)

Content1. Project Resource Managementp5 Introducing the PRMp6 Understanding the PRMp7 Structure Discipline Resourcesp11 Accessing & Checking the PRM p152. Feature Dictionaryp16 About the Feature Dictionaryp17 Starting the Feature Dictionary Editorp18 Managing Attributes p19 Discrete Valuesp21 Managing ID Numberp223. Standard Section Catalogsp24 Managing Parametric Sectionsp25 Generating Resolved Partsp30 Creating/Modifying Standard Section Catalogsp32 Creating/Modifying the StructureSpecificationMaterial Catalogsp344. Detailing Featuresp41 Design Rules and Recommendationsp42 End-Cutsp45 Slotsp51 Small Assembliesp54 Storing Detailing Features in a catalogp57

What is new in this releaseNew way of section catalog management

ExercisesEx. 1: Creating a New Project (180min) / All sectorsEx. 2: Adding New Attributes (180min) / All sectorsEx. 3: Creating a Resolved Standard section (240min) / All sectorsEx. 4: Modifying the StructureSpecifiactionMaterial Catalog (240min) / AllsectorsEx. 5: Creating a Standard End-Cut (180min) / All sectorsEx. 6: Creating a Contextual End-Cut (180min) / All sectorsEx. 7: Creating a Slot (180min) / All sectorsEx. 8: Creating a Small Assembly (180min) / All sectors



TG1: Tooling Design

EDU-CAT-E-TG1-FCourse Code EDU-CAT-E-TG1-FCATIA V5R17Brand & Release CATIA V5R171.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-TG1-FI-V5R17 Foils: EDU-CAT-E-TG1-FF-V5R17 Exercises: EDU-CAT-E-TG1-FX-V5R17 Detailed Steps: EDU-CAT-E-TG1-FS-V5R17

ObjectivesIn this course you will learn how to use workbench Tooling Design to createand instantiate Components in a Mold or Die Structure

Participants' ProfileNew Tooling Design users

PrerequisitesCATIA V5 FundamentalsMechanical Design Fundamentals

ContentIntroduction to Tooling DesignCreating ComponentsEditing ComponentsSpecific Components : Inserts & SlidersAdvanced Add/Remove CapabilitiesManaging User ComponentsTool Design to ManufacturingAnalyzing the contextual Links in the Assembly structureCustomizing the Bill of Material of a Mold/Die ProductWorking with Large assemblies : Cache Management

ExercisesEx. 1: Phone Handset (150min) / All sectors



V5E: CATIA V5 Expert Mechanical Designer

EDU-CAT-E-V5E-ACourse Code EDU-CAT-E-V5E-ACATIA V5R17Brand & Release CATIA V5R175 daysDuration 5 daysEnglishLanguage EnglishAdvancedLevel AdvancedILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5E-AI-V5R17 Foils: EDU-CAT-E-V5E-AF-V5R17

Objectives- Create a complex model in CATIA V5- Create and manage a structured model- Design parts in the context of an assembly- Re-use existing data to complete assemblies- Manage relationships between assembled parts- Analyze and annotate your design

Participants' ProfileMechanical designers already having an experience of CATIA V5 mechanicaldesign foundations.

PrerequisitesTraining on CATIA V5 FundamentalsMechanical design experience

ContentThis course will teach you how to start a complex design project from itsspecifications (top down approach) and complete it by reusing existing data. Itwill focus on advanced skills and concepts that enable you to create andanalyze complex parts and assemblies.

Lesson 1: IntroductionLesson 2: Design Complex PartsLesson 3: Surface DesignLesson 4: Analyze and Annotate PartsLesson 5: Sharing InformationLesson 6: Assembly DesignLesson 7: Design in ContextLesson 8: Complex Assembly DesignMaster Project 1: Mobile PhoneMaster Project 2: Lifting Truck

What is new in this releaseNow available in Companion


ExercisesEx. 1: Case Study: Introduction (40min) / AutomotiveEx. 2: Exercise 2A (20min) / All sectorsEx. 3: Exercise 2B (15min) / All sectorsEx. 4: Exercise 2C (20min) / All sectorsEx. 5: Exercise 2D (30min) / AutomotiveEx. 6: Exercise 2E (5min) / All sectorsEx. 7: Exercise 2F (30min) / All sectorsEx. 8: Exercise 2G (20min) / All sectorsEx. 9: Exercise 2H (20min) / All sectorsEx. 10: Exercise 2I (15min) / All sectorsEx. 11: Case Study: Design Complex Parts (40min) / Consumer PackagedGoodsEx. 12: Exercise 3A (20min) / All sectorsEx. 13: Exercise 3B (20min) / All sectorsEx. 14: Exercise 3C (5min) / All sectorsEx. 15: Exercise 3D (30min) / All sectorsEx. 16: Exercise 3E (20min) / Consumer Packaged GoodsEx. 17: Exercise 3F (20min) / All sectorsEx. 18: Exercise 3G (15min) / All sectorsEx. 19: Exercise 3H (20min) / Consumer Packaged GoodsEx. 20: Case Study: Surface Design (40min) / All sectorsEx. 21: Exercise 4A (20min) / AutomotiveEx. 22: Exercise 4B (20min) / All sectorsEx. 23: Exercise 4C (20min) / All sectorsEx. 24: Exercise 4D (20min) / All sectorsEx. 25: Exercise 5A (10min) / All sectorsEx. 26: Exercise 5B (10min) / All sectorsEx. 27: Exercise 5C (15min) / All sectorsEx. 28: Exercise 5D (20min) / All sectorsEx. 29: Exercise 5E (20min) / All sectorsEx. 30: Exercise 5F (20min) / All sectorsEx. 31: Case Study: Sharing Information (30min) / All sectorsEx. 32: Exercise 6A (15min) / All sectorsEx. 33: Exercise 6B (20min) / All sectorsEx. 34: Exercise 6C (20min) / All sectorsEx. 35: Exercise 6D (20min) / All sectorsEx. 36: Exercise 6E (20min) / All sectorsEx. 37: Exercise 6F (30min) / All sectorsEx. 38: Exercise 6G (10min) / All sectorsEx. 39: Case Study: Assembly Design (40min) / All sectorsEx. 40: Exercise 7A (20min) / All sectorsEx. 41: Exercise 7B (20min) / All sectorsEx. 42: Exercise 7C (20min) / All sectorsEx. 43: Exercise 7D (20min) / All sectorsEx. 44: Exercise 7E (20min) / All sectorsEx. 45: Exercise 7F (20min) / All sectorsEx. 46: Exercise 7G (30min) / All sectorsEx. 47: Case Study: Contextual Design (40min) / Consumer Packaged GoodsEx. 48: Exercise 8A (20min) / All sectorsEx. 49: Exercise 8B (20min) / All sectorsEx. 50: Exercise 8C (90min) / AutomotiveEx. 51: Exercise 8D (20min) / All sectorsEx. 52: Exercise 8E (30min) / All sectorsEx. 53: Case Study: Complex Assembly Design (80min) / All sectorsEx. 54: Master Project 1 (100min) / Electronics & ElectricalEx. 55: Master Project 2 (240min) / Fabrication & Assemblies ConsumerGoods



V5F: CATIA V5 Fundamentals

EDU-CAT-E-V5F-FCourse Code EDU-CAT-E-V5F-FCATIA V5R17Brand & Release CATIA V5R175 daysDuration 5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5F-FI-V5R17 Foils: EDU-CAT-E-V5F-FF-V5R17

Objectives- Understand the CATIA V5 interface- Plan the construction of a part in order to properly convey its visual andfunctional aspects- Create simple parts in CATIA V5- Understand how to manage parts in the context of an assembly- Produce simple drawings and assembly layouts

Participants' ProfileNew CATIA V5 Mechanical Designers

PrerequisitesMechanical design experience.Experience with the Windows operating system.

ContentThis course will introduce you to CATIA V5. It will teach you how to buildsimple parts and assemblies in CATIA, and how to make simple drawings ofthose parts and assemblies.

- Lesson 1: Introduction to CATIA- Lesson 2: Profile Creation

- Lesson 3: Basic Features

- Lesson 4: Additional Features

- Lesson 5: Dress-Up Features

- Lesson 6: Reusing Data

- Lesson 7: Finalizing Design Intent

- Lesson 8: Assembly Design

- Lesson 9: Design in Context

- Lesson 10: Drafting ISO

- Lesson 10: Drafting ANSI

What is new in this releaseNow a Companion course


ExercisesEx. 1: Key Terms & Design Intent Exercise: 1A (20min) / All sectorsEx. 2: Getting Started with CATIA Exercise: 1B (20min) / All sectorsEx. 3: Case Study: Drill Press Master Project (20min) / All sectorsEx. 4: Create New Part Exercise: 2A, 2B, 2C (40min) / All sectorsEx. 5: Constraining a Sketch Exercise: 2D, 2E, 2F (40min) / All sectorsEx. 6: Case Study: Support Plate (15min) / All sectorsEx. 7: Creating with Basic Features Exercise: 3A, 3B, 3C (40min) / All sectorsEx. 8: Part Investigation Exercise: 3D, 3E (20min) / All sectorsEx. 9: Case Study: Engine Support (20min) / All sectorsEx. 10: Create with Additional Features Exercise: 4A, 4B, 4C (45min) / AllsectorsEx. 11: Create Revolved Features Exercise: 4D, 4E, 4F (45min) / All sectorsEx. 12: Create Shell and Thin Features Exercise: 4G, 4H, 4I (50min) / AllsectorsEx. 13: Case Study: Handle Block (20min) / All sectorsEx. 14: Create Dress-up Features Exercise: 5A, 5B, 5C (50min) / All sectorsEx. 15: Editing Features Exercise: 5D, 5E, 5F (50min) / All sectorsEx. 16: Case Study: Casing Support (25min) / All sectorsEx. 17: Reusing Data Exercise: 6A, 6B, 6C (50min) / All sectorsEx. 18: Reusing Data Part 2 Exercise: 6D, 6E, 6F (50min) / All sectorsEx. 19: Case Study: Engine (35min) / All sectorsEx. 20: Finalizing Design Intent Exercise: 7A, 7B, 7C, 7D, 7E (80min) / AllsectorsEx. 21: Case Study: Table (35min) / All sectorsEx. 22: Introduction to Assembly Design Exercise: 8A, 8B, 8C (50min) / AllsectorsEx. 23: Adding Assembly Design Components Exercise: 8D, 8E, 8F (60min) /All sectorsEx. 24: Case Study: Handle Mechanism (35min) / All sectorsEx. 25: Design in Context Exercise: 9A, 9B, 9C, 9D, 9E (120min) / All sectorsEx. 26: Case Study: Chuck (30min) / All sectorsEx. 27: Creating the Drawing Exercise: 10A, 10B, 10C (30min) / All sectorsEx. 28: Case Study: Base (20min) / All sectorsEx. 29: Master Project: Part Creation (60min) / All sectorsEx. 30: Master Project: Finalize the Part (45min) / All sectorsEx. 31: Master Project: Create an Assembly (60min) / All sectorsEx. 32: Master Project: Edit a Part (40min) / All sectorsEx. 33: Master Project: Create a Drawing (20min) / All sectors



Machining Solutions


MachiningSolutions

AMG: Advanced Part Machining

EDU-CAT-E-AMG-FCourse Code EDU-CAT-E-AMG-FCATIA V5R17Brand & Release CATIA V5R171.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-AMG-FI-V5R17 Foils: EDU-CAT-E-AMG-FF-V5R17 Exercises: EDU-CAT-E-AMG-FX-V5R17

ObjectivesIn this course, you will learn how to define:- Multi-Axis Flank Contouring operation- Multi-Axis Helix machining operation- Cavities Roughing operation

Participants' ProfileManufacturing users knowing how to work with CATIA V5 parts

PrerequisitesFundamentals about CATIA V5

Content- Multi Axis Flank Contouring operation presentation- Geometry tab- Strategy tab- Multi Axis Helix machining operation presentation- Geometry tab- Strategy tab- Cavities Roughing operation presentation- Geometry tab- Strategy tab

ExercisesEx. 1: Multi-Axis Contouring operation (20min) / All sectorsEx. 2: Flank finishing (5min) / All sectorsEx. 3: Start and End in closed pocket (5min) / All sectorsEx. 4: Joggle management (5min) / All sectorsEx. 5: Thickness on tool path (5min) / All sectorsEx. 6: Curves as part (5min) / All sectorsEx. 7: Local modifications (10min) / All sectorsEx. 8: Non contiguous drives (10min) / All sectorsEx. 9: Non contiguous drives 2 (10min) / All sectorsEx. 10: Non contiguous drives in same plane (10min) / All sectorsEx. 11: Auxilliary guiding (10min) / All sectorsEx. 12: Mx-Helix 01 : Rough body blade / All sectorsEx. 13: Mx-Helix 02 : Rough foot blade (10min) / All sectorsEx. 14: Mx-Pocket 01 : Rough Frame (10min) / All sectorsEx. 15: Mx-Pocket 02 : Rough Zone (10min) / All sectorsEx. 16: Mx-Helix 03 : Interpol (10min) / All sectors


MachiningSolutions

LMG: Lathe Machining

EDU-CAT-E-LMG-FCourse Code EDU-CAT-E-LMG-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-LMG-FI-V5R17 Foils: EDU-CAT-E-LMG-FF-V5R17 Exercises: EDU-CAT-E-LMG-FX-V5R17 Detailed Steps: EDU-CAT-E-LMG-FS-V5R17

ObjectivesBy the end this course you will be able to define and manage NC Programsdedicated to Machining Parts using Lathe Machining techniques. You will alsobe able to program Roughing, Finishing, Recessing, Grooving, Threading, andDrilling operations, and manage the Lathe Tools.

Participants' ProfileManufacturing users working with CATIA V5 Parts

PrerequisitesCATIA V5 FundamentalsNumerical Control Infrastructure

ContentLathe Operations- Rough Turning- Groove Turning- Recess Turning- Profile Finish Turning- Groove finish Turning- Thread Turning- Sequential Turning- Ramp Rough Turning- Ramp Recess Turning- Lathe Tool assembly

- Design Associativity- Machining Process for Lathe operation creation

- Methodologies for Groove Turning- Turning on Milling Center with Facing Head

ExercisesEx. 1: Cylindrical Structure Part (130min) / All sectors


MachiningSolutions

MMG: Multi-Axis Surface Machining

EDU-CAT-E-MMG-FCourse Code EDU-CAT-E-MMG-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MMG-FI-V5R17 Foils: EDU-CAT-E-MMG-FF-V5R17 Exercises: EDU-CAT-E-MMG-FX-V5R17

ObjectivesIn this course, you will learn how to define and manage NC programs tomachine Surface or Solid geometry using 5-Axis machining techniques.

Participants' ProfileManufacturing users

PrerequisitesFundamentals about CATIA V5NC Manufacturing Infrastructure3-Axis Surface Machining

Content- Multi-Axis Sweeping Operation- Multi-Axis Contour Driven Operation- Multi-Axis Curve Machining Operation- Multi-Axis Isoparametric Machining Operation- Multi-Axis Drilling Operation

ExercisesEx. 1: Fender (90min) / All sectorsEx. 2: Hood (40min) / AutomotiveEx. 3: Pocket (15min) / All sectorsEx. 4: Isoparametric and Drill (15min) / All sectors


MachiningSolutions

MPA: Prismatic Machining Preparation Assistant

EDU-CAT-E-MPA-FCourse Code EDU-CAT-E-MPA-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MPA-FI-V5R17 Foils: EDU-CAT-E-MPA-FF-V5R17 Exercises: EDU-CAT-E-MPA-FX-V5R17 Detailed Steps: EDU-CAT-E-MPA-FS-V5R17

ObjectivesIn this course you will see how to define and manage NC programs to machineparts designed in 3D Wireframe or Solid geometry with 2.5 Axis machiningoperations and how this product assists the NC programmer in making the linkbetween Design and Manufacturing.

Participants' ProfileManufacturing users knowing how to work with CATIA V5 Parts and Processes

PrerequisitesCATIA V5 FundamentalsPMG-F: Prismatic Machining

Content- Introduction to Prismatic Machining Preparation Assistant- Global features recognition- Locall features recognition - Machinable Axial Features Pattern Creation

ExercisesEx. 1: Prismatic Part (60min) / All sectorsEx. 2: Holes management (15min) / All sectors


MachiningSolutions

MPG: Multi Pocket Machining

EDU-CAT-E-MPG-FCourse Code EDU-CAT-E-MPG-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-MPG-FI-V5R17 Foils: EDU-CAT-E-MPG-FF-V5R17 Exercises: EDU-CAT-E-MPG-FX-V5R17

ObjectivesIn this course, you will learn how to define a power Machining operation

Participants' ProfileManufacturing users knowing how to work with CATIA V5 parts

PrerequisitesFundamentals about CATIA V5Users already trained with other milling course

Content- Power machining operation presentation- Geometry tab- Strategy tab- Offsets management

ExercisesEx. 1: Power machining frame (15min) / All sectors


MachiningSolutions

NCI: Numerical Control Infrastructure

EDU-CAT-E-NCI-FCourse Code EDU-CAT-E-NCI-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-NCI-FI-V5R17 Foils: EDU-CAT-E-NCI-FF-V5R17 Exercises: EDU-CAT-E-NCI-FX-V5R17 Detailed Steps: EDU-CAT-E-NCI-FS-V5R17

ObjectivesBy the end of this course you will be able to create a Manufacturing Program,simulate it and generate outputs. You will be able to perform the following NCManufacturing Infrastructure functions:- Manage Tools and Tool Catalogs- Define and Verify the Tool Path- Generate NC data using an integrated Post Processor- Create Shop-floor Documentation- - Manage Design Changes- Import V4 Data

Participants' ProfileManufacturing Users (NC Programmers)


ContentCOMMON TOPICSLesson 1 : Workbench PresentationLesson 2 : Define Setup (Part Operation)Lesson 3 : Machining Operation, Macros, Tools PresentationLesson 4 : Tool Path Verification & Simulationlesson 5 : Auto sequencelesson 6 : Auxiliary Operationslesson 7 : Output generationlesson 8 : Axial Operationslesson 9 : Hole selection - Machining Pattern Managementlesson 10 : The different Process ViewsLesson 11 : Geometry wizard (edge, surface)

ADVANCED TOPICSLesson 12 : Import & Modify Tool PathLesson 13 : Resource ManagementLesson 14 : PP Word Table customizationLesson 15 : V4 NCMill & NCLathe Set Import (optional)Lesson 16 : Design Change ManagementLesson 17 : Machining Processes

APPENDIXSettings


ExercisesEx. 1: CATProcess & Workbencg Presentation (5min) / All sectorsEx. 2: Machining Operation Presentation (15min) / All sectorsEx. 3: Replay Simulate and analyze (15min) / All sectorsEx. 4: Generate Auxiliary operation (30min) / All sectorsEx. 5: Generate Outputs (15min) / All sectorsEx. 6: Create Spot drilling and a drilling Operations (15min) / All sectorsEx. 7: Import APT source File (30min) / All sectorsEx. 8: Manage Resources (30min) / All sectorsEx. 9: Auto Complete (30min) / All sectorsEx. 10: PP Word Table (30min) / All sectorsEx. 11: Import V4 NC data (NCMill / NCLathe) (30min) / All sectorsEx. 12: Design Change (30min) / All sectorsEx. 13: Machining Process creation & instantiation (60min) / All sectors


MachiningSolutions

PMG: Prismatic Machining

EDU-CAT-E-PMG-FCourse Code EDU-CAT-E-PMG-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PMG-FI-V5R17 Foils: EDU-CAT-E-PMG-FF-V5R17 Exercises: EDU-CAT-E-PMG-FX-V5R17 Detailed Steps: EDU-CAT-E-PMG-FS-V5R17

ObjectivesAt the end of this course, participants will be able to define and manageprismatic (2,5 axis) operations, being aware of all capabilities in terms ofstrategies, parameters and transition paths.

Participants' ProfileManufacturing users knowing how to work with CATIA V5 Parts

PrerequisitesFundamentals about CATIA V5 and Machining

ContentMilling operations: - Facing,- Pocketing, - Prismatic Roughing,- Profile contouring,- Groove milling,- Point to point, - Curve following, - Prismatic rework area,- Prismatic machining area,- Transition Paths (macros)

ExercisesEx. 1: Aerospace structure part (130min) / All sectorsEx. 2: Prismatic Part (180min) / All sectorsEx. 3: Fitting Part (120min) / All sectorsEx. 4: Flap Track part (180min) / All sectorsEx. 5: AIrframe part (30min) / All sectors


MachiningSolutions

SMG: 3-Axis Surface Machining

EDU-CAT-E-SMG-FCourse Code EDU-CAT-E-SMG-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-SMG-FI-V5R17 Foils: EDU-CAT-E-SMG-FF-V5R17 Exercises: EDU-CAT-E-SMG-FX-V5R17 Detailed Steps: EDU-CAT-E-SMG-FS-V5R17

ObjectivesIn this course, you will see how to define and manage NC programs dedicatedto machining parts designed with Surface or Solid geometry using 3-Axismachining techniques.

Participants' ProfileManufacturing users

PrerequisitesFundamentals about CATIA V5 and Machining

ContentIntroduction to the 3-Axis Surface Machining Accessing the Workbench Workbench the user interface Process/Product/Resources model Manufacturing terminology General process

Creating geometrical elements Creates rough stock Inserts an STL file Creates a stock by offset Points creation wizard Limit lines projection wizard Limit lines creation wizard

Creating a Machining Feature Geometrical Zone Creation Machining/Slope Area Creation Rework Area Creation Offset group Creation

Creating a 3-Axis Surface Machining Operation 3-Axis Machining Operations Sweep Roughing Operation Roughing Operation Sweeping Operation Pencil Operation Zlevel Operation Contour-driven Operation Isoparametric machining Operation Spiral milling Operation Profile Contouring Operation

Analysing and modifying tool path


ExercisesEx. 1: Master exercise Renfort (140min) / All sectorsEx. 2: Create a roughing operation (30min) / All sectorsEx. 3: Create an isoparametric machining operation (30min) / All sectorsEx. 4: Create a spiral milling operation (30min) / All sectorsEx. 5: Create NC geometrical element, slope area and rework area (30min) /All sectorsEx. 6: Create a contouring operation (30min) / All sectorsEx. 7: Analyse and modify a computed tool path (20min) / All sectors


MachiningSolutions

STL: STL Rapid Prototyping

EDU-CAT-E-STL-FCourse Code EDU-CAT-E-STL-FCATIA V5R17Brand & Release CATIA V5R170.3 dayDuration 0.3 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-STL-FI-V5R17 Foils: EDU-CAT-E-STL-FF-V5R17 Exercises: EDU-CAT-E-STL-FX-V5R17

ObjectivesIn this course, you will learn how to create meshes from solids or surfacesusing the application STL Rapid Prototyping.

Participants' ProfileSurface Designer

PrerequisitesDSE-F: Digitized Shape Editor

Content- Introduction- Creating a mesh from a basic surface- Tuning the mesh- Giving a thickness to the mesh- Optimizing the mesh- Exporting the mesh as an STL file

ExercisesEx. 1: Portable Vacuum Cleaner (40min) / Fabrication & Assemblies ConsumerGoods



Product Synthesis Solutions


Product SynthesisSolutions

HMN: Human Modeling

EDU-CAT-E-HMN-FCourse Code EDU-CAT-E-HMN-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-HMN-FI-V5R17 Foils: EDU-CAT-E-HMN-FF-V5R17 Exercises: EDU-CAT-E-HMN-FX-V5R17 Detailed Steps: EDU-CAT-E-HMN-FS-V5R17

ObjectivesIn this course, you will learn how to use our Human Model technology in orderto leverage your ergonomics analysis. Among other things, you will learn howto position and manipulate the manikins within a V5 scene. In addition, you willevaluate the comfort, the reach, clearance, and the vision of your targetpopulation. Additional to standard ergonomics analysis you will evaluateinteraction between the manikin and geometries in the scene. Finally, you willrealize a simulation (animation).

Participants' Profile- Designers- Engineers- Human factors specialists- Any Health specialist

PrerequisitesCourse on Digital mock-up

ContentYou will use the Ergonomics Design & Analysis tools to review the ergonomicsaspect of a manikin inside and around a vehicle, with the tools of theworkbenches: Human Builder, Human Measurement Editor, Human ActivityAnalysis and Human Postural Analysis.

ExercisesEx. 1: Ergonomics review inside a vehicle with Human Measurement Editor(240min) / AutomotiveEx. 2: Ergonomics review inside a vehicle with Human Postural Analysis(240min) / AutomotiveEx. 3: Ergonomics review around a vehicle with Human Activity Analysis(240min) / AutomotiveEx. 4: Ergonomics review inside a vehicle with Human Builder (240min) /Automotive



KWA: Knowledge Advisor

EDU-CAT-E-KWA-FCourse Code EDU-CAT-E-KWA-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWA-FI-V5R17 Foils: EDU-CAT-E-KWA-FF-V5R17 Exercises: EDU-CAT-E-KWA-FX-V5R17 Detailed Steps: EDU-CAT-E-KWA-FS-V5R17

ObjectivesAccess the Knowledgeware working environmentCreate user parameters and formulaeCreate Design Tables and use them to create part familiesCreate reaction features that react to an event such as an updateUse the Macro with Argument featureUse inspection, equations, law and loop tools


PrerequisitesCATIA V5 Basics

ContentThis course you will teach you how to manage Knowledge Advisor objects inorder to embed knowledge within a design. It will teach you how to useknowledge rules to reduce errors and automate modifications.

-Workbench presentation-Creating user parameters and formulas-Defining Checks, Rules, Reactions, Lists, Laws, Loops and macros witharguments-Associating URLs to parameters or relations-Running macros from Rules or Reactions-Using the Knowledge Inspector tool-Managing Design Tables and part family catalogs

ExercisesEx. 1: Wheel Rim (90min) / All sectorsEx. 2: Light Bulb (60min) / All sectorsEx. 3: Sheet Metal Part (30min) / All sectors



KWE: Knowledge Expert

EDU-CAT-E-KWE-FCourse Code EDU-CAT-E-KWE-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWE-FI-V5R17 Foils: EDU-CAT-E-KWE-FF-V5R17 Exercises: EDU-CAT-E-KWE-FX-V5R17

ObjectivesUse the Knowledge Expert working environmentBuild and analyze Expert ChecksStore and re-use rulesArchive the results of the Check Analysis using Check Reports

Participants' ProfileUsers implementing the Know-how on the design quality as design rules,security norms and company standards.

PrerequisitesCATIA V5 Basics

ContentThis course you will show how to build up and share corporate knowledgestored in rule bases, and leverage it across the company to ensure designcompliance with established standards.

- Workbench presentation- Creating a rule base and a rule set- Creating an expert rule- Creating an expert check- Navigating the object browser- Accessing the Expert Check/Rule in the Check/Rule body- Solving a rule base- Generating a check report- Performing a Global Analysis of Checks- Working with rule bases and catalogs- Creating expert rules or expert checks on User Features

ExercisesEx. 1: Connector (40min) / All sectorsEx. 2: LBlock Correction (40min) / All sectors



KWF: Knowledge Fundamentals

EDU-CAT-E-KWF-FCourse Code EDU-CAT-E-KWF-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-KWF-FI-V5R17 Foils: EDU-CAT-E-KWF-FF-V5R17 Exercises: EDU-CAT-E-KWF-FX-V5R17

ObjectivesAt the end of this course, trainees should be able to create and use parametricparts and assemblies, without any help.

Participants' ProfileMechanical design engineer with project management responsibilities.

PrerequisitesPDG-F: Part Design FundamentalsASS-F: Assembly Design Fundamentals

Content- Introduction to knowledge tools- Common Knowledge Tools- Collaborative Work and Knowledge

What is new in this releaseNew topic on Powercopy

ExercisesEx. 1: Common Knowledge Tools Exercise : Bolt and Stringer (40min) / AllsectorsEx. 2: Collaborative Work and Knowledge Exercise : Grip Assembly (45min) /All sectorsEx. 3: Stringer Assembly - Step 1 : Creating user parameters and formulas(10min) / All sectorsEx. 4: Stringer Assembly - Step 2 : Importing Rules and Checks (10min) / AllsectorsEx. 5: Stringer Assembly - Step 3 : Using a Design Table (10min) / All sectorsEx. 6: Stringer Assembly - Step 4 : Publishing Parameters (5min) / All sectorsEx. 7: Stringer Assembly - Step 5 : Creating User Parameters and formulas(10min) / All sectorsEx. 8: Stringer Assembly - Step 6 :Using parameters as external references(15min) / All sectorsEx. 9: Stringer Assembly - Step 7 : Replacing component (5min) / All sectors



PEO: Product Engineering Optimizer

EDU-CAT-E-PEO-FCourse Code EDU-CAT-E-PEO-FCATIA V5R17Brand & Release CATIA V5R170.7 dayDuration 0.7 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PEO-FI-V5R17 Foils: EDU-CAT-E-PEO-FF-V5R17 Exercises: EDU-CAT-E-PEO-FX-V5R17 Detailed Steps: EDU-CAT-E-PEO-FS-V5R17

ObjectivesIn this course, you will learn the functionalities of CATIA Product EngineeringOptimizer (PEO): - Definition of an optimization problem- Specification of the optimization algorithm,- Solving of an optimization problem,- Analyzing and reporting on the results, - Use of the Design of Experiments tool to understand the behavior of a systemthanks to space exploration,- Use of the Constraint Satisfaction tool to solve complex contraint problems(with no objective function)

Participants' ProfileCATIA V5 Users

PrerequisitesCATIA Basics

Content- Workbench Presentation- Optimization Problem Formulation- Optimization problem resolution- Solution analysis- Best practices for optimization with PEO- Design of Experiments tool- Constraint Satisfaction tool

ExercisesEx. 1: Strap tension optimization (90min) / All sectorsEx. 2: Beam mass optimization (30min) / All sectorsEx. 3: Shape optimization: Hanger (40min) / All sectorsEx. 4: Fastener Shape Optimization (30min) / All sectorsEx. 5: Surfacic structure Structural Optimization (20min) / All sectorsEx. 6: Child Swing Structural Optimization (25min) / All sectorsEx. 7: Silo Structural Optimization (30min) / All sectorsEx. 8: Design of experiments (30min) / All sectorsEx. 9: Beam Mass Minimization through Constraint Satisfaction (20min) / Allsectors



Shape Design & Styling Solutions


Shape Design & StylingSolutions

DL1: Developed Shapes

EDU-CAT-E-DL1-FCourse Code EDU-CAT-E-DL1-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DL1-FI-V5R17 Foils: EDU-CAT-E-DL1-FF-V5R17 Exercises: EDU-CAT-E-DL1-FX-V5R17 Detailed Steps: EDU-CAT-E-DL1-FS-V5R17

ObjectivesThe objectives of these documents are to have the users familiar with developwires and unfolded surfaces concepts and functionalities


PrerequisitesWFS-F: Wireframe and Surface DesignGSD-F: Generative Shape Design

ContentUser interface and functionalitiesUser interfaceUnfolded surfaces Unfolded surfaces: Concept definition Unfolded surfaces functionalitiesDevelop wires Develop wires: Concept definition Develop wires: functionalitiesExercise PresentationTo Sum Up

ExercisesEx. 1: Water bottle and its support (40min) / All sectors



DSE: Digitized Shape Editor

EDU-CAT-E-DSE-FCourse Code EDU-CAT-E-DSE-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-DSE-FI-V5R17 Foils: EDU-CAT-E-DSE-FF-V5R17 Exercises: EDU-CAT-E-DSE-FX-V5R17

ObjectivesUpon Completion of this course you will be able to:- Import and optimize digitized data such as cloud of points- Compute and optimize a mesh based on digitized data- Extract the characteristic curves of a mesh


PrerequisitesStudents attending this course should be familiar with the basics of curvescreation

ContentThis course will teach you how to import, clean and optimize digitized datasuch as clouds of points. You will also learn how to create an optimized meshon the digitized data and how to extract the characteristic curves from thismesh.

- Introduction to Digitized Shape Editor- Point processing- Mesh processing- Scans and curves- Advanced tasks

ExercisesEx. 1: Car Door (80min) / AutomotiveEx. 2: Hair Dryer (75min) / Fabrication & Assemblies Consumer Goods



FSK: FreeStyle Sketch Tracer

EDU-CAT-E-FSK-FCourse Code EDU-CAT-E-FSK-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FSK-FI-V5R17 Foils: EDU-CAT-E-FSK-FF-V5R17 Exercises: EDU-CAT-E-FSK-FX-V5R17

Objectives- Use pictures as background or as a basis for design- Import a picture into CATIA V5 - Position a picture in the CATIA V5 environment

Participants' ProfileSurface Designers

PrerequisitesGS1: CATIA Surface Design (EDU-CAT-E-GS1-F - V5R16)

ContentThis course will teach you how to use pictures in the CATIA V5 environment asbackground or as a basis for your design.

- Import an image- Position an image

What is new in this releaseSea Car exercise modified

ExercisesEx. 1: Sea Car (20min) / Automotive



FSS: FreeStyle Shaper, Optimizer & Profiler

EDU-CAT-E-FSS-FCourse Code EDU-CAT-E-FSS-FCATIA V5R17Brand & Release CATIA V5R171.5 daysDuration 1.5 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-FSS-FI-V5R17 Foils: EDU-CAT-E-FSS-FF-V5R17 Exercises: EDU-CAT-E-FSS-FX-V5R17

Objectives- Create styled shapes using with digitized data- Create surfaces using a curve-based approach- Create surfaces using a surface-based approach - Analyze and correct curve quality- Analyze and correct surface quality

Participants' ProfileSurface Designers

PrerequisitesGS1: CATIA Surface Design (EDU-CAT-E-GS1-F - V5R16)

ContentThis course teaches you how to create flawless, styled shapes from scratchusing three-dimensional free-form curves and surfaces or with digitized data.You will also learn how to analyze and improve the quality of existing curvesand surfaces.

Introduction to Freestyle Shaper

Curve Based Approach

Surface Based Approach

Analysis Tools

What is new in this release- New exercise on car example

ExercisesEx. 1: Sea Car - Curve approach (140min) / AutomotiveEx. 2: Hair Dryer - Surface Approach (140min) / All sectors



GSD: Surface Design Expert

EDU-CAT-E-GSD-FCourse Code EDU-CAT-E-GSD-FCATIA V5R17Brand & Release CATIA V5R172 daysDuration 2 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSD-FI-V5R17 Foils: EDU-CAT-E-GSD-FF-V5R17 Exercises: EDU-CAT-E-GSD-FX-V5R17 Detailed Steps: EDU-CAT-E-GSD-FS-V5R17

ObjectivesUpon completion of this course, you will be able to:- Correctly recall the tools of the Generative Shape Design workbench that arecommon to MD2 and HD2 licenses- Identify and use the Generative Shape Design tools that are specific to theHD2 license- Create advanced and parameterized swept surfaces- Perform advanced surfaces analysis and gap correction- Understand the mechanism of a multi-model environment including the use ofsurfaces


PrerequisitesStudents attending this course should be familiar with the basics of wireframeand surfaces creation

ContentThis course focuses on the Generative Shape Design tools specific to the HD2license and will first recall and summarize the tools covered in the SurfaceDesign course. You will capitalize on this with advanced surfaces creationtools, quality checking and correction techniques, and be introduced to surfacecreation in a multi-model environment.

- Surface Design Overview- Creating Advanced Wireframe Geometry- Wireframe Analysis and Repair- Creating Advanced Swept Surfaces- Creating Advanced Blend Surfaces- Surface Analysis and Repair- Additional Surface Design Tools

What is new in this releaseThis course was updated in order to reflect the main CATIA V5R17enhancements


ExercisesEx. 1: Advanced Wireframe Geometry (15min) / All sectorsEx. 2: Wireframe Analysis and Repair (10min) / All sectorsEx. 3: Shampoo Bottle (40min) / All sectorsEx. 4: Knob (60min) / All sectorsEx. 5: Advanced Swept Surfaces (30min) / All sectorsEx. 6: Mobile Phone (60min) / All sectorsEx. 7: Advanced Blending Surface (30min) / All sectorsEx. 8: Surface Analysis (30min) / All sectorsEx. 9: Hybrid Design (30min) / All sectorsEx. 10: Mirror Shell (60min) / All sectorsEx. 11: Plastic Bottle (180min) / All sectorsEx. 12: B-Pillar (60min) / AutomotiveEx. 13: Space Mouse Base (180min) / All sectorsEx. 14: Lemon Squeezer (180min) / All sectorsEx. 15: Driving Mirror (60min) / All sectorsEx. 16: Cover (60min) / All sectors



GSO: Generative Shape Optimizer

EDU-CAT-E-GSO-FCourse Code EDU-CAT-E-GSO-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-GSO-FI-V5R17 Foils: EDU-CAT-E-GSO-FF-V5R17 Exercises: EDU-CAT-E-GSO-FX-V5R17 Detailed Steps: EDU-CAT-E-GSO-FS-V5R17

ObjectivesUpon completion of this course, you will be able to:- Identify in the GSD workbench the tools specific to Generative ShapeOptimizer- Manage volumes- Develop shapes and curves on surfaces- Create junctions between existing beams- Morph surfaces using target curves and shapes- Add bumps on surfaces


PrerequisitesStudents attending this course should be familiar with the GSD workbench

ContentThis course introduces you to the Generative Shape Optimizer tools within theGSD workbench. You will learn how to manage volumes and how to defomrshapes using the morphing and bump tools. You will also learn how to developshapes and how to create junctions between beams.

Introduction to Generative Shape Optimizer - Accessing Generative Shape Optimizer - The User InterfaceCreating Offsets: - Variable Offset - Rough OffsetDeveloping Shapes: - Developing wireUsing BiW Tools: - Creating junctions - Creating a Diabolo SeatCreating Advanced Surfaces: - Creating bumped surfaces - Deforming surfaces according to curve wrapping - Deforming surfaces according to surface wrapping - Shape MorphingCreating Volumes - What is a Volume - Types of Volumes - Volumes made from Sketches - Volumes made from Surfaces - Dress-up features on Volumes - Volumes using Boolean operations - Volumes from Operations or Transformations


ExercisesEx. 1: Door Junction (40min) / All sectorsEx. 2: Holding Arm (30min) / All sectorsEx. 3: Torch (40min) / All sectorsEx. 4: Steering Wheel (60min) / Automotive



HD2: Generative Shape Design V5R17 Update

EDU-CAT-E-HD2-UCourse Code EDU-CAT-E-HD2-UCATIA V5R17Brand & Release CATIA V5R170.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-HD2-UI-V5R17 Foils: EDU-CAT-E-HD2-UF-V5R17

ObjectivesThis course will teach you the principle new tools available in CATIA V5R17Hybrid Design. You will learn what is the WYSIWYG mode and how to use it.You will also learn to use the new circle sweep types

At the end of this course you will be able to:- Identify the principle new hybrid design tools available in CATIA V5R17- Use the WYSIWYG mode- Use the new circle sweep types


PrerequisitesSurface Design Expert

ContentWYSIWYG modeCircle sweep enhancements

What is new in this releaseNew R17 Course

ExercisesEx. 1: Create a mask (10min) / All sectorsEx. 2: Adaptive sweep (15min) / All sectors



IMA: Imagine & Shape

EDU-CAT-E-IMA-FCourse Code EDU-CAT-E-IMA-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-IMA-FI-V5R17 Foils: EDU-CAT-E-IMA-FF-V5R17 Exercises: EDU-CAT-E-IMA-FX-V5R17

ObjectivesUpon Completion of this course you will be able to:- Explain what is a subdivision surface- Create and deform subdivision surfaces- Create and deform IMA curves with the curve modeler- Associate curves with subdivision surfaces

Participants' ProfileThis course is targeted mainly for CATIA:Application engineersMechanical DesignersIndustrial Designers

PrerequisitesStudents attending this course should be familiar with the Generative ShapeDesign workbench

ContentThis course will introduce the concept of subdivision surfaces and will teachyou the tools available to create these surfaces. You will learn themanipulations necessary to modify and shape the subdivision surfaces. Youwill also learn how to create curves with the curve modeler and how toassociate subdivision surfaces with curves.

Introduction to Imagine & Shape

Surface modeling:-Creating Basic Surfaces-Manipulating Surfaces-Modifying the Topology

Curve modeling:-Curve creation-CUrve deformation

Curve creation:-Curve deformation-Sketching-Manipulate point-Smoothing-Fillet-Erase-On plane

Imaging and Shape Recommendation


ExercisesEx. 1: Basic Shapes Recap (20min) / All sectorsEx. 2: Perfume bottle (40min) / All sectorsEx. 3: Hair Dryer (40min) / All sectorsEx. 4: Video Projector (50min) / All sectorsEx. 5: Bicycle (120min) / All sectorsEx. 6: Lamp (60min) / All sectorsEx. 7: Power hand Tool (60min) / All sectorsEx. 8: Camera (40min) / All sectorsEx. 9: Toy (120min) / All sectorsEx. 10: Motorcycle (180min) / All sectors



PHS: Photo Studio

EDU-CAT-E-PHS-FCourse Code EDU-CAT-E-PHS-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PHS-FI-V5R17 Foils: EDU-CAT-E-PHS-FF-V5R17 Exercises: EDU-CAT-E-PHS-FX-V5R17 Detailed Steps: EDU-CAT-E-PHS-FS-V5R17

ObjectivesIn this course, you will learn how to create a photo realistic image

Participants' ProfileNew CATIA V5 Users


Content- Environment management- Camera management- Light sources management- Shooting management- Textures management- Stickers management- Animation: Turntable management- Animation: Animating scene elements

ExercisesEx. 1: Phone Handset (150min) / Fabrication & Assemblies Consumer Goods



PSO: Photo Studio Optimizer

EDU-CAT-E-PSO-FCourse Code EDU-CAT-E-PSO-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-PSO-FI-V5R17 Foils: EDU-CAT-E-PSO-FF-V5R17

ObjectivesIn this course, you will learn how to use advanced options to create a photorealistic image


PrerequisitesCATIA BasicsCATIA Photo Studio

Content- 3D textures- Bump mapping- Global illumination- Caustics- Visual effects

ExercisesNone



QSR: Quick Surface Reconstruction

EDU-CAT-E-QSR-FCourse Code EDU-CAT-E-QSR-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-QSR-FI-V5R17 Foils: EDU-CAT-E-QSR-FF-V5R17 Exercises: EDU-CAT-E-QSR-FX-V5R17

ObjectivesUpon Completion of this course you will be able to:- Identify the tools that are specific to QSR and those that are common withDigitized Shape Editor- Quickly create scans and curves on an imported cloud of points- Quickly create simple surfaces on resulting scans and curves


PrerequisitesStudents attending this course should be familiar with the Digitized ShapeEditor and Generative Shape Design workbenches

ContentThis course will show you how to reuse tools from Digitized Shape Editorworkbench, and which are the tools specific to QSR. You will learn how scansand curves can be rapidly created on a mesh, and how surfaces can be quicklyderived from the resulting curves.

- Introduction- Creating scans- Creating curves- Creating surfaces- Create curve networks- Automatic processes

ExercisesEx. 1: Plastic Bottle (120min) / Fabrication & Assemblies Consumer GoodsEx. 2: Exercise 2 : Washing Powder Bottle (120min) / Fabrication & AssembliesConsumer GoodsEx. 3: Exercise 3 : Toy Plastic Part (120min) / All sectorsEx. 4: Exercise 4 : Car body (120min) / Automotive



RSO: Realistic Shape Optimizer

EDU-CAT-E-RSO-FCourse Code EDU-CAT-E-RSO-FCATIA V5R17Brand & Release CATIA V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-RSO-FI-V5R17 Foils: EDU-CAT-E-RSO-FF-V5R17 Exercises: EDU-CAT-E-RSO-FX-V5R17

ObjectivesIn this course you will learn how to deform a surface or a set of surfaces usinga displacement file resulting from a finite element analysis

Participants' ProfileSurface design Specialist or Expert Surface designers involved in tooling design

PrerequisitesGS1: CATIA Surface Design Companionor

CCV: Core & Cavity Design

ContentIntroduction to Realistic Shape Optimizer - Why do you need RSO ?Workbench presentation- Accessing the workbenchSurface Deformation - Digitized Morphing- Update Digitized Morphing

ExercisesEx. 1: Master exercise: Plastic Cover (30min) / All sectorsEx. 2: Additionnal exercise: Plane wing (30min) / Aerospace



RTR: Real Time Rendering

EDU-CAT-E-RTR-FCourse Code EDU-CAT-E-RTR-FCATIA V5R17Brand & Release CATIA V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-RTR-FI-V5R17 Foils: EDU-CAT-E-RTR-FF-V5R17 Exercises: EDU-CAT-E-RTR-FX-V5R17

ObjectivesIn this course, you will learn how to interactively create realistic and dynamicrenderings



Content- Environment management- Camera management- Light sources management- DMU integration- Textures management- Stickers management- Animation: Turntable management- Animation: Animating scene elements

ExercisesEx. 1: Defining an Environment (5min) / AutomotiveEx. 2: Defining the Camera (10min) / All sectorsEx. 3: Defining the Light Source (10min) / AutomotiveEx. 4: Applying Texture (40min) / AutomotiveEx. 5: Applying Stickers (10min) / AutomotiveEx. 6: Creating an Animation Using a Turntable (15min) / AutomotiveEx. 7: Creating an Animation of Scene (15min) / Automotive



V5S: V5 Surface Design

EDU-CAT-E-V5S-FCourse Code EDU-CAT-E-V5S-FCATIA V5R17Brand & Release CATIA V5R173 daysDuration 3 daysEnglishLanguage EnglishFundamentalsLevel FundamentalsILTMethod ILT

Training Material ReferencesInstructor Foils: EDU-CAT-E-V5S-FI-V5R17 Foils: EDU-CAT-E-V5S-FF-V5R17

ObjectivesThis course introduces the students to the creation of quality curves andsurfaces in the GSD workbench. You will learn how to analyse the wireframeand surfaces quality and how to correct the deteceted defects. You will also beintroduced to the work in a multimodel enevironment with published surfaces.

Upon Completion of this course you will be able to:- understand the GSD workbench - create good quality curves or improve imported wireframe- create good quality surfaces based on a sound wireframe geometry- assemble, relimit and smoothly connect the surfaces to get a topology- analyze surfaces quality and heal the surfaces defects.- manage surfaces in a multimodel environment

Participants' ProfileMechanical surface Designers

PrerequisitesV5F: CATIA V5 Fundamentals (EDU-CAT-E-V5F-F - V5R17)

ContentThis course contains 6 lessons: Lesson 1: Introduction to GSD Lesson 2 :Wireframe Creation (Reference Geometry Creation, 3D CurveCreation, Curve Continuity Management) Lesson 3: Surface Creation (Choice of Surfaces, Extruding or RevolvingProfile, Sweeping a Profile, Create a Multi Section Surface, Create an AdaptiveSweep Surface) Lesson 4 : Surface Re-limitation and Connection (Relimit the Surfaces,Assemble the Surfaces) Lesson 5 : Surface Check Tools (Surface Continuity Check, SurfaceMoldability Check) Lesson 6 : Work in Multi-Model Environment with Surface (Surface andWireframe Publication, Use Published Surface in Product)

What is new in this releaseNew course

NotesIn addition to the exercises specified just above, this course contains:- Exercises included in the flow of the lessons to make students to manipulateon simple data and get familiar with the tools- Case Study exercises at the end of each lesson to allow students to reviewthe tools seen in the lesson in a more concret set of data

This course also contains CATIA demonstration data including instructions inthe CATParts (3D annotations) to help the teacher to show what has to beshown.These demonstration data are also provided to the students (for lessons 2 to 5)to make the students manipulate while the teacher demonstrates.


ExercisesEx. 1: Master Project: Toy Car (200min) / All sectorsEx. 2: Additional Exercise: Mobile Phone (60min) / All sectorsEx. 3: Additional Exercise: Plastic Bottle (180min) / All sectors


Digital Mock-Up Course Material

Digital Mock-Up Solutions


Digital Mock-UpSolutions

ANR: DMU Engineering Analysis Review

EDU-DMU-E-ANR-FCourse Code EDU-DMU-E-ANR-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R170.1 dayDuration 0.1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-ANR-FI-V5R17 Foils: EDU-DMU-E-ANR-FF-V5R17 Exercises: EDU-DMU-E-ANR-FX-V5R17 Detailed Steps: EDU-DMU-E-ANR-FS-V5R17

ObjectivesUse the DMU Analysis workbench Review analyses from the Analysis and Simulation workbenchesReview analyses coming from third party applications. Animate an assemblyDetect extrema and analyze assembly sectionsGenerate and manage resulting images and reports

Participants' ProfileDesigners (P2 users only)

PrerequisitesDMB-F: Digital Mock Up BasicsDMN-F: Digital Mock Up NavigatorSPA-F: Digital Mock Space Analysis

ContentThis course will show you how to review parts and products which have beenpreviously analysed using Analysis and Simulation workbench tools.

- DMU Engineering Analysis Review Overview- Generating Results- Managing Results

ExercisesEx. 1: Generate Results (5min) / All sectorsEx. 2: Animate Image (15min) / All sectors



DMB: Digital Mock Up Basics

EDU-DMU-E-DMB-FCourse Code EDU-DMU-E-DMB-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMB-FI-V5R17 Foils: EDU-DMU-E-DMB-FF-V5R17 Exercises: EDU-DMU-E-DMB-FX-V5R17

Objectives- Understand the capabilities of the Digital Mock-Up workbenches - Manage assembly components and explore mock-up details - Manipulate view points- Perform measurements- Highlight critical areas using 2D and 3D annotationsLink information to external files

Participants' ProfileCatia and All DMU Users


ContentThis course will allow you understand the general capabilities of the CATIA V5digital mock-up workbenches. It will allow you to visualize and investigate acomplex assembly, to investigate problem areas and highlight critical points.

- Introduction to DMU- Preparing the Session- Editing Components- Navigating through Components- Managing Viewpoints- Basic Measuring- Annotating

ExercisesEx. 1: DS Business Jet : Customizing your session (5min) / All sectorsEx. 2: DS Business Jet : Editing Components (20min) / All sectorsEx. 3: DS Business Jet : Navigating Through Components (5min) / All sectorsEx. 4: DS Business Jet : Navigation (5min) / All sectorsEx. 5: DS Business Jet : Managing Viewpoints (15min) / All sectorsEx. 6: DS Business Jet : Measuring (15min) / All sectorsEx. 7: DS Business Jet : Annotating (15min) / All sectors



DMN: Digital Mock Up Navigator

EDU-DMU-E-DMN-FCourse Code EDU-DMU-E-DMN-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMN-FI-V5R17 Foils: EDU-DMU-E-DMN-FF-V5R17 Exercises: EDU-DMU-E-DMN-FX-V5R17

ObjectivesWork with basic and advanced functionalities of the DMU Navigator workbenchModify components’ properties and position componentsAnimate the Mock-up by creating simulations and create movies fromsimulationsManage Mock-up configurations with scenesSave specific Mock-up configurations for analysis purposesCreate annotated views of the Mock-Up for communication purposes

Participants' ProfileDesigners, Managers

PrerequisitesDMU Basics

ContentThis course will show you how to manipulate a Digital Mock-Up in the contextof an engineering review, and make simulations to create review presentations

- Introduction to DMU Navigator- Managing Components- Managing Simulations- Managing Video Animations- Managing Scenes- Managing and Presenting Applicative Data- Managing 2D Documents

ExercisesEx. 1: DS Business-Jet : Managing Components (10min) / All sectorsEx. 2: DS Business-Jet : Creating Simulations (20min) / All sectorsEx. 3: DS Business-Jet : Generating Video Animations (15min) / All sectorsEx. 4: DS Business-Jet : Creating and Editing Enhanced Scenes (15min) / AllsectorsEx. 5: DS Business-Jet : Managing DMU Presentations (10min) / All sectors



DMO: Digital Mock Up Optimizer

EDU-DMU-E-DMO-FCourse Code EDU-DMU-E-DMO-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMO-FI-V5R17 Foils: EDU-DMU-E-DMO-FF-V5R17 Exercises: EDU-DMU-E-DMO-FX-V5R17

ObjectivesUnderstand which DMU Settings and capabilities are used to managesimplified representationsHow to select, and when to use, a simplified representationCompute thickness and offset representationsCompute swept and vibration volumesCompute Free Space and 3D Cut representations for measurement purposes


PrerequisitesDMB-F: Digital Mock Up BasicsSPA-F: Digital Mock Space Analysis

ContentThis course will show you how to improve productivity by computing anoptimized data geometric representation for rapid mockup verification in thecontext of a collaborative design review environment.

- About Alternate Shapes- Simplifying a Representation- Generating Thickness and Offset- Generating Swept Volume and Vibration Volume- Generating Free Space and 3D Cut

NotesNew Master Exercise based on a Washing Machine

ExercisesEx. 1: Computing a Simplification (10min) / All sectorsEx. 2: Define a Silhouette (10min) / All sectorsEx. 3: Define a Wrapping (10min) / All sectorsEx. 4: Define a Thickness (10min) / All sectorsEx. 5: Define an Offset (10min) / All sectorsEx. 6: Define Swept and Vibration Volumes (15min) / All sectorsEx. 7: Computing Free Space (5min) / All sectorsEx. 8: Computing a 3D Cut (10min) / All sectors



DMU: Digital Mock-Up V5R17 Update

EDU-DMU-E-DMU-UCourse Code EDU-DMU-E-DMU-UDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R170.1 dayDuration 0.1 dayEnglishLanguage EnglishUpdateLevel UpdateCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-DMU-UI-V5R17 Foils: EDU-DMU-E-DMU-UF-V5R17

ObjectivesUpon the completion of this course you will be able to use the new andenhancement tools in various Digital Mock-up workbenches in V5R17 Release.

Participants' ProfileMechanical Designers, Industrial Designers, Managers

PrerequisitesDigital Mock-up V5R16 Courses

ContentDigital Mock-Up Navigator EnhancementsDigital Mock-Up Space Analysis Enhancements

ExercisesNone



FIT: Digital Mock-Up Fitting Simulator

EDU-DMU-E-FIT-FCourse Code EDU-DMU-E-FIT-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-FIT-FI-V5R17 Foils: EDU-DMU-E-FIT-FF-V5R17 Exercises: EDU-DMU-E-FIT-FX-V5R17

ObjectivesUnderstand the general process of fitting simulationDefine shuttles and groups.Create tracks with which to move components or a group of componentsDefine the order in which the tracks and actions will take placeGet the time duration for each track and actionPerform clash analysis during sequence and tracks simulation


PrerequisitesDMB-F: Digital Mock Up BasicsDMN-F: Digital Mock Up Navigator

ContentThis course will show you how to efficiently define the procedure of mountingand un-mounting component parts. You will learn how to optimize the processfor ease of assembly and maintenance.

- Introduction- Defining Shuttle- Defining Tracks- Creating Sequences- Performing Clash Analysis- Other Helpful Tools

ExercisesEx. 1: Car Suspension – Play the Ready-To-Use replay (5min) / AutomotiveEx. 2: Car Suspension – Manage Actions (10min) / AutomotiveEx. 3: Car Suspension – Manage Sequences (10min) / AutomotiveEx. 4: Car Suspension – Compute Swept Volume (5min) / Automotive



KIN: Digital Mock-Up Kinematics Simulator

EDU-DMU-E-KIN-FCourse Code EDU-DMU-E-KIN-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R171 dayDuration 1 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-KIN-FI-V5R17 Foils: EDU-DMU-E-KIN-FF-V5R17 Exercises: EDU-DMU-E-KIN-FX-V5R17

Objectives"Efficiently use the capabilities of the DMU Kinematics workbenchCreate the motion instructions for a mechanismAnimate a mechanismPerform analyses during simulation Link and animate multiple mechanisms"


PrerequisitesDMB-F: Digital Mock Up BasicsSPA-F: Digital Mock Up Space Analysis

ContentThis course will show you how to design mechanisms from an existingassembly. You will also learn to simulate and analyze the mechanisms forclashes and other types of analysis.

- DMU Kinematics an Overview- Defining a Mechanism- Simulating Mechanisms- Analyzing Movements- Recording and Playing Simulations- Miscellaneous Functionalities

NotesCourse structure changed +Brand new Master Exercise based on an Elliptical Sport Trainer

ExercisesEx. 1: Plane – Step1: Create a Mechanism (15min) / All sectorsEx. 2: Plane – Step2: Convert Assembly Constraints (15min) / All sectorsEx. 3: Plane – Step3 : Simulate the Mechanism (10min) / All sectorsEx. 4: Plane – Step4: Create an Animation (15min) / All sectorsEx. 5: Plane – Step5: Compute Swept Volume and Trace (15min) / All sectorsEx. 6: Master Exercise : Elliptical Trainer (120min) / All sectors



SPA: Digital Mock-Up Space Analysis

EDU-DMU-E-SPA-FCourse Code EDU-DMU-E-SPA-FDigital Mock-Up V5R17Brand & Release Digital Mock-Up V5R170.5 dayDuration 0.5 dayEnglishLanguage EnglishFundamentalsLevel FundamentalsCompanion and ILTMethod Companion and ILT

Training Material ReferencesInstructor Foils: EDU-DMU-E-SPA-FI-V5R17 Foils: EDU-DMU-E-SPA-FF-V5R17 Exercises: EDU-DMU-E-SPA-FX-V5R17

ObjectivesPerform measurements in the context of a digital mock upCreate views to see inner details of the digital mock upPerform interference checking in order to find clashes, contacts and verifycomponent clearancesCompare different versions of a digital mock-up

Participants' ProfileDesigners, Managers

PrerequisitesDMB-F: Digital Mock Up Basics

ContentThis course will show you how to review and validate designs throughout theproduct life cycle from design in context to maintenance review. You will learnhow to highlight interference problems and verify internal componentclearances.

- Introduction to DMU Space Analysis- Measuring- Sectioning- Analyzing Interferences- Comparing Products

ExercisesEx. 1: Measuring Distances (10min) / All sectorsEx. 2: Sectioning (20min) / All sectorsEx. 3: Analyzing Interferences (15min) / All sectors
