CD200 Service Manual

Table of Contents

Installation

Electrical

Plumbing

Kits

Final Checklist

Start Up

Operation

Electrical Sequence

Component Description

Service Diagnosis

Removal and Replacement

After Placing Ice Machineon Dispenser, Level The

Assembled Cabinets.

LOCATION

Select a location that allows the ice machine thatwill be placed on top of the dispenser access forservice and adequate air flow. Check the manualof the ice machine for air flow requirements.

The CD200B dispenser is designed to be usedwith a variety of Scotsman cube ice machines.They include:

•Bin thermostat models: CME250, CME500 andCME656.

•Electronic models: CME256, CME506 andCME656.

Follow the detailed installation instructions in thetext of the ice machine’s manual. Note: Some icemachines are equipped with a bin thermostat andbracket. Do NOT install the ice machine’s binthermostat BRACKET.

CD200s mfg. beginning May 1997 have an internalthermostat to control the CME256, CME506 orCME656. Follow the Control System installationinstructions packaged with the CD200 to connectthe CME256, CME506 or CME656 control systemto the CD200.

Cabinet Connection Hardwareis From Ice Machine’s

Hardware Package.

FOR THE INSTALLERCD200

May 1997Page 4

Electronic Cuber Model Shown

BIN CONTROL

Bin Thermostat Models: A bin thermostat bracketis built into the top of the CD200. After the icemachine has been placed on the top of theCD200, route the bin thermostat capillary tubefrom the control box of the ice machine, thru therouting hole at the back of the ice machine’s waterreservoir, and into the tubular bracket in the top ofthe CD200. Check to be sure that the binthermostat’s capillary tube is IN the bracket andthat it stops at the end of the tube.

Electronic Models: CD200s mfg. beginning May1997 have an internal thermostat with wiringharness. The wiring harness must be routed fromthe CD200 to the CME256, CME506 or CME656.Follow instructions supplied separately on theCD200.

The Baffle and Thermostat bracket werediscontinued beginning with May 1997 production.

Note: Prior CD200s without the removable binthermostat plate must be retrofitted with kit,KBTCD200.

Cabinet AssemblyCD200

May 1997Page 5

Electrical Connections

Ice Machine PowerConnection

Separate Circuitsfor Dispenser and

Ice Machine

Dispenser PowerConnection

Electrical Connections,Electronic Model Shown

DISPENSER

Connect the electrical power to the junction box atthe rear of the dispenser cabinet.

See the dispenser’s nameplate (located on theback) for the electrical voltage, minimum circuitampacity and maximum fuse size. The unitrequires a solid chassis to earth ground wire. Seethe wiring diagram.

The dispenser should be connected to a separatecircuit. Voltage variation must not exceed tenpercent above or below the nameplate voltage atany time.

FOLLOW ALL LOCAL, STATE and NATIONALCODES.

ICE MACHINE

Connect the electrical power to the junction box atthe back of the ice machine. Follow the directionsin the ice machine’s manual.

CD200

January 1996Page 6

Plumbing

Vented DrainConnection

DISPENSER

The only plumbing connection required for theCD200 is the base drain, it is a 3/4" FPTconnection located at the bottom back of thecabinet.

Be certain to route this drain separately from anyother, and to vent the drain tube.

ICE MACHINE

Follow the detailed plumbing installationinstructions in the service or product manualpacked with the specific ice machine.

CONFORM TO ALL APPLICABLE CODES

CD200

January 1996Page 7

Power?

Water? Ice Machine

Drains?

Final Check List Dispenser

1. Is the ice machine properly installed?

2. Is the unit level?

3. Has the water been connected to the icemachine?

4. Has the electrical power been provided to theice machine and dispenser?

5. Have the drain lines been run?

6. Fill out the warranty registration and mail it.

CD200

January 1996Page 9

ON-OFFSwitch

Vend Switch

Hopper

Sink

Start Up

Always check the installation before beginning astart up. Do not start up a machine until it has been properly installed.

1. Start up the ice machine, following the directionsgiven in the manual packed with the ice machine.

2. Allow the ice machine to make several batchesof ice, so the dispensing mechanism can be tested.

3. Locate the sink key, and remove the sinkassembly by pulling the bottom away from thedispenser, then pulling the sink down.

4. Check that the ON-OFF switch is in the ONposition.

5. Return the sink assembly to its normal, lockedposition.

6. Push the vend switch in (units without coin orkey mechanisms) to start the dispensing cycle. Icewill fill the hopper and the rotating wheel inside thedispenser will stop.

7. Push the hopper down to release the ice.

8. Repeat step 6, but this time push the hopperdown during the dispensing process, the processshould stop. Release the hopper and dispensingshould continue. If not, remove the sink and checkthe action of the safety switch at the top of the sinkassembly.

9. Pour water in the sink area to check for properdrainage.

10. Give the sink key to the owner/user and informthem about the operation and maintenance of themachine.

CD200

January 1996Page 10