chapter 13 lubrication and sliding bearingsturbolab.hanyang.ac.kr/2021_04_29_teaching...
TRANSCRIPT
![Page 1: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/1.jpg)
April. 29. 2021
[Chanwoo Lee]
Turbomachinery Laboratory
Hanyang University, Korea
CHAPTER 13
Lubrication and Sliding
Bearings
![Page 2: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/2.jpg)
© Turbomachinery Laboratory at Hanyang University 2
Sliding Friction on Wet and Dry Sand
Sliding friction over and between sand
layers is relevant for many problems
ranging from civil engineering to
earthquake dynamics.
In many practical situations, small
amounts of water may be present.
Ancient Egyptian tomb drawings
suggest that wetting the sand with
water may influence the friction
between a sled and the sand (Fig. 1).
![Page 3: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/3.jpg)
© Turbomachinery Laboratory at Hanyang University 3
13.1 Types of Lubricants
The word bearing, applied to a machine or structure, refers to
contacting surfaces through which a load is transmitted.
When relative motion occurs between the surfaces, it is usually
desirable to minimize friction and wear.
Any interposed substance that reduces friction and wear is a lubricant.
Lubricants are usually liquid but can be a solid, such as graphite, TFE,
or molybdenum disulfide, or a gas, such as pressurized air.
![Page 4: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/4.jpg)
© Turbomachinery Laboratory at Hanyang University 4
13.1 Types of Lubricants – Viscosity (13.5)
The viscosity of a fluid is a measure of its resistance to gradual
deformation by shear stress or tensile stress.
![Page 5: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/5.jpg)
© Turbomachinery Laboratory at Hanyang University 5
Viscosity versus Temperature
13.1 Types of Lubricants
![Page 6: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/6.jpg)
© Turbomachinery Laboratory at Hanyang University 6
13.1 Types of Lubricants
Liquid lubricants that are oils are characterized by their viscosity, butother properties are also important.
Modern oils usually contain one or more additives designed to causethe oil to flow at lower temperatures—the pour-point depressants;have less variation of viscosity with temperature
Greases are liquid lubricants that have been thickened in order toprovide properties not available in the liquid lubricant alone.
Greases are usually used where the lubricant is required to stay inposition, particularly when frequent lubrication is difficult or costly.
![Page 7: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/7.jpg)
© Turbomachinery Laboratory at Hanyang University 7
Engine oil Bearing grease
13.1 Types of Lubricants
https://kixxman.com/engine-oil-viscosity-1
https://www.bearingtips.com/bearing-lubrication-methods/
![Page 8: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/8.jpg)
© Turbomachinery Laboratory at Hanyang University 8
13.1 Multi-grade Oils
The temperature range the oil is exposed to in most vehicles can be wide,ranging from cold temperatures in the winter before the vehicle is startedup, to hot operating temperatures when the vehicle is fully warmed up inhot summer weather.
A specific oil will have high viscosity when cold and a lower viscosity at theengine's operating temperature. The difference in viscosities for mostsingle-grade oil is too large between the extremes of temperature.
https://en.wikipedia.org/wiki/Motor_oil#Multi-grade_motor_oil
![Page 9: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/9.jpg)
© Turbomachinery Laboratory at Hanyang University 9
13.1 Multi-grade Oils
To bring the difference in viscosities closer together, special polymer additivescalled viscosity index improvers, or VIIs are added to the oil.
These additives are used to make the oil a multi-grade motor oil, though it ispossible to have a multi-grade oil without the use of VIIs.
The idea is to cause the multi-grade oil to have the viscosity of the base gradewhen cold and the viscosity of the second grade when hot. This enables one typeof oil to be used all year.
In fact, when multi-grades were initially developed, they were frequentlydescribed as all-season oil.
https://en.wikipedia.org/wiki/Motor_oil#Multi-grade_motor_oil
![Page 10: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/10.jpg)
© Turbomachinery Laboratory at Hanyang University 10
13.2 Types Sliding Bearings
https://en.wikipedia.org/wiki/Motor_oil#Multi-grade_motor_oil
Sliding bearings require direct sliding of the load-carrying member on
its support, as distinguished from rolling-element bearings (Chapter
14), where balls or rollers are interposed between the sliding surfaces.
Sliding bearings (also called plain bearings) are of two types:
1) Journal or sleeve bearings, which are cylindrical and support radial
loads (those perpendicular to the shaft axis)
2) Thrust bearings, which are generally flat and, in the case of a
rotating shaft, support loads in the direction of the shaft axis.
![Page 11: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/11.jpg)
© Turbomachinery Laboratory at Hanyang University 11
Journal bearing Thrust bearing
https://www.gtw.cz/en/tilting-pad-journal-bearings/
https://www.machinerylubrication.com/Read/587/thrust-bearings
13.2 Types Sliding Bearings
![Page 12: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/12.jpg)
© Turbomachinery Laboratory at Hanyang University 12
13.2 Types Sliding Bearings
https://en.wikipedia.org/wiki/Motor_oil#Multi-grade_motor_oil
![Page 13: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/13.jpg)
© Turbomachinery Laboratory at Hanyang University 13
13.3 Types of Lubrication
![Page 14: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/14.jpg)
© Turbomachinery Laboratory at Hanyang University 14
13.3 Hydrodynamic lubrication
In hydrodynamic lubrication the surfaces are completely separated by
the lubricant film.
The load tending to bring the surfaces together is supported entirely
by fluid pressure generated by relative motion of the surfaces (as
journal rotation).
Surface wear does not occur, and friction losses originate only within
the lubricant film.
Typical values of coefficient of friction (f) are 0.002 to 0.010.
![Page 15: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/15.jpg)
© Turbomachinery Laboratory at Hanyang University 15
13.3 Mixed-film lubrication
In mixed-film lubrication the surface peaks are intermittently in
contact, and there is partial hydrodynamic support.
With proper design, surface wear can be mild.
Coefficients of friction commonly range from 0.004 to 0.10.
![Page 16: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/16.jpg)
© Turbomachinery Laboratory at Hanyang University 16
13.3 Boundary lubrication
In boundary lubrication surface contact is continuous and extensive,
but the lubricant is continuously “smeared” over the surfaces and
provides a continuously renewed adsorbed surface film that reduces
friction and wear.
Typical values of f are 0.05 to 0.20.
![Page 17: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/17.jpg)
© Turbomachinery Laboratory at Hanyang University 17
Complete surface separation (as in Figure 13.2a) can also beachieved by hydrostatic lubrication. A highly pressurized fluid such asair, oil, or water is introduced into the load-bearing area.
Since the fluid is pressurized by external means, full surfaceseparation can be obtained whether or not there is relative motionbetween the surfaces.
The principal advantage is extremely low friction at all times, includingduring starting and low-speed operation.
Disadvantages are the cost, complication, and bulk of the externalsource of fluid pressurization. Hydrostatic lubrication is used only forspecialized applications.
13.3 Hydrostatic lubrication
![Page 18: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/18.jpg)
© Turbomachinery Laboratory at Hanyang University 18
13.4 Basic Concepts of Hydrodynamic Lubrication
![Page 19: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/19.jpg)
© Turbomachinery Laboratory at Hanyang University 19
13.4 Basic Concepts of Hydrodynamic Lubrication
If the shaft rotating speed is progressively increased, more and more oil adhering
to the journal surface tries to come into the contact zone until finally enough
pressure is built up just ahead of the contact zone to “float” the shaft, as shown in
Figure 13.3c.
When this happens, the high pressure of the converging oil flow to the right of the
minimum film thickness position (h0) moves the shaft slightly to the left of center.
Under suitable conditions, equilibrium is established with full separation of the
journal and bearing surfaces.
This constitutes hydrodynamic lubrication, also known as full-film or thick-film
lubrication. The equilibrium eccentricity of the journal in the bearing is dimension
e, shown in Figure 13.3c.
![Page 20: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/20.jpg)
© Turbomachinery Laboratory at Hanyang University 20
13.4 Basic Concepts of Hydrodynamic Lubrication
Hydrodynamic Pressure
https://dyrobes.com/help1800/BePerf/html/bepe7zn7.htm
![Page 21: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/21.jpg)
© Turbomachinery Laboratory at Hanyang University 21
13.4 Basic Concepts of Hydrodynamic Lubrication
Attitude angle: In a bearing, the angle betweenthe resultant of the radial loads acting on a rotorand a line connecting the bearing and shaftcenters, measured in the direction of rotation.
Eccentricity: The radial displacement of the rotorjournal centerline from the geometric center ofa fluid-film bearing
Eccentricity ratio: A dimensionless quantityrepresenting the average position of the shaftwithin the bearing compared to the availableclearance.
![Page 22: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/22.jpg)
© Turbomachinery Laboratory at Hanyang University 22
13.4 Basic Concepts of Hydrodynamic Lubrication
![Page 23: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/23.jpg)
© Turbomachinery Laboratory at Hanyang University 23
13.4 Basic Concepts of Hydrodynamic Lubrication
Bearings enable smooth (low friction) motion between solid surfaces in relative motion
and, if well designed, support static and dynamic loads. Bearing affect the dynamic
performance of machinery
Full film lubricationGas bearings operate at the
three regimes of lubrication +
Dry friction at start up shut
down
![Page 24: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/24.jpg)
© Turbomachinery Laboratory at Hanyang University 24
13.4 Basic Concepts of Hydrodynamic Lubrication
![Page 25: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/25.jpg)
© Turbomachinery Laboratory at Hanyang University 25
13.4 Basic Concepts of Hydrodynamic Lubrication
Note that the achievement of hydrodynamic lubrication requires three things.
1. Relative motion of the surfaces to be separated.
2. “Wedging action,” as provided by the shaft eccentricity.
3. The presence of a suitable fluid.
![Page 26: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/26.jpg)
© Turbomachinery Laboratory at Hanyang University 26
13.5 Viscosity
Analogy between viscosity m of
a fluid (also called dynamic
viscosity and absolute viscosity)
and shear modulus of elasticity
G of a solid.
![Page 27: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/27.jpg)
© Turbomachinery Laboratory at Hanyang University 27
Figure 13.5a shows a rubber bushing
bonded between a fixed shaft and an outer
housing.
Application of torque T to the housing
subjects an element of the rubber bushing
to a fixed displacement, as shown in
Figure 13.5b.
If the material between the housing and
concentric shaft is a Newtonian fluid (as
are most lubricating oils), equilibrium of an
element involves a fixed velocity, as
shown in Figure 13.5c.
13.5 Viscosity
![Page 28: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/28.jpg)
© Turbomachinery Laboratory at Hanyang University 28
13.5 Viscosity
![Page 29: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/29.jpg)
© Turbomachinery Laboratory at Hanyang University 29
13.5 Kinematic Viscosity
![Page 30: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/30.jpg)
© Turbomachinery Laboratory at Hanyang University 30
13.5 Absolute viscosity
![Page 31: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/31.jpg)
© Turbomachinery Laboratory at Hanyang University 31
13.5 SAE Grades
The Society of Automotive Engineers classifies oils according to viscosity.
Viscosity–temperature curves for typical SAE numbered oils are given in Figure 13.6.
A particular oil may deviate significantly from these curves, for the SAE
specifications define a continuous series of viscosity bands. For example, an SAE 30
oil may be only a trifle more viscous than the “thickest” SAE 20, or only a trifle less
viscous than the “thinnest” SAE 40 oil.
Furthermore, each viscosity band is specified at only one temperature. SAE 20, 30,
40, and 50 are specified at 100°C (212°F) whereas SAE 5W, 10W, and 20W are
specified at -18°C (0°F).
Multigrade oils must conform to a viscosity specification at both temperatures.
For example, an SAE 10W-40 oil must satisfy the 10W viscosity requirement at -
18°C and the SAE 40 requirement at 100°C.
![Page 32: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/32.jpg)
© Turbomachinery Laboratory at Hanyang University 32
![Page 33: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/33.jpg)
© Turbomachinery Laboratory at Hanyang University 33
13.5 Viscosity and SAE Number
![Page 34: CHAPTER 13 Lubrication and Sliding Bearingsturbolab.hanyang.ac.kr/2021_04_29_Teaching Fellow_Lee.pdfSliding bearings (also called plain bearings) are of two types: 1) Journal or sleeve](https://reader035.vdocument.in/reader035/viewer/2022071510/612e37941ecc51586942ac8f/html5/thumbnails/34.jpg)
© Turbomachinery Laboratory at Hanyang University 34
Thank you!