chapter 4

48
Lesson 4 – UNDERSTANDING NETWORK CABLING

Upload: networksguy

Post on 20-Jan-2015

955 views

Category:

Documents


0 download

DESCRIPTION

 

TRANSCRIPT

Page 1: Chapter 4

Lesson 4 – UNDERSTANDING NETWORK CABLING

Page 2: Chapter 4

Network topologies

Network cabling

Installing and maintaining Network cabling

Selecting and installing a SOHO Network

OVERVIEW

Page 3: Chapter 4

Network topology = Shape of the Network.

It is the most important step in planning a Network.

NETWORK TOPOLOGIES

Page 4: Chapter 4

Bus topology

Star topology

Ring topology

Types of Network topologies

Page 5: Chapter 4

Common Bus Multipoint Topology.

1 cable from one end of the Network to the other.

Devices are connected to the cable at different locations.

Bus topology

Page 6: Chapter 4

Bus topology

Page 7: Chapter 4

Specifications:

Number of nodes in a segment.

Number of segments used through repeaters.

Proximity of nodes to each other.

Length of a segment.

Coax cable required.

Termination of bus ends.

Bus topology

Page 8: Chapter 4

Networks use:

Coaxial cable

BNC T-connectors

Bus topology

Page 9: Chapter 4

Advantages:

Least expensive.

Uses less material.

Needs less installation labor.

Bus topology

Page 10: Chapter 4

Drawbacks:

Failure in a part of the segment causes the entire segment to

fail.

Troubleshooting can take a long time.

Tends to be unreliable.

Bus topology

Page 11: Chapter 4

10Base-2 Ethernet has:

Better performance.

Maximum speed of 10Mbps.

RG-58/AU or RG-58/CU coaxial cable and BNC connectors.

50-ohm terminating connector.

Maximum of 30 nodes per segment.

Maximum segment length of 185 meters (607 feet).

Extended segments through the use of repeaters.

1.5 feet distance between nodes.

Bus topology

Page 12: Chapter 4

A central unit, called a hub or concentrator, hosts a set of network cables that radiate out to each node on the Network.

Star topology

Page 13: Chapter 4

Star topology

Page 14: Chapter 4

Uses either:

10Base-T Ethernet.

100Base-T Ethernet.

Star topology

Page 15: Chapter 4

10Base-T Ethernet:

Requires four wires (two twisted-pairs in a single sheath).

Can be run on Cat 3 or Cat 5 cable.

Is limited to a length of 100 meters.

Is unlimited in the number of nodes in a segment.

Uses RJ-45 connectors.

Star topology

Page 16: Chapter 4

100Base-T Ethernet:

Requires eight actual wires (four twisted-pairs in a single

sheath).

Uses Cat 5 cable or better.

Is limited to a length of 100 meters.

Is unlimited in the number of nodes in a segment.

Uses RJ-45 connectors.

Star topology

Page 17: Chapter 4

Star topology Networks cost more.

In a Star topology, a single Network connection that goes

bad affects only that connection.

Star topology Vs. Bus topology

Page 18: Chapter 4

Rings are a logical arrangement.

The cables are wired in a star, with each node connected on

its own cable to the MAU.

Electrically the Network behaves like a ring.

It is based on Token Ring instead of Ethernet.

Ring topology

Page 19: Chapter 4

Ring topology

Page 20: Chapter 4

Ethernet Networks manage signals through CSMA/CD

(Carrier Sense Multiple Access/with Collision Detection).

Token Ring Networks manage their bandwidth with “token

passing”.

Rings Vs. Stars and Bus:

Page 21: Chapter 4

Basic cable types:

Unshielded twisted-pair (UTP)

Shielded twisted-pair (STP)

Coaxial

Fiber-optic cable

NETWORK CABLING

Page 22: Chapter 4

Unshielded twisted-pair

Page 23: Chapter 4

Similar to UTP, but has a braided metal shield surrounding

the twisted pairs.

The metal shield reduces the chance of interference from

external electrical sources.

Shielded twisted-pair

Page 24: Chapter 4

Coaxial cable

Page 25: Chapter 4

Uses a glass strand and carries data signals as light instead

of electricity.

This cable can easily reach 2 miles at 100Mbps.

Fiber-optic cable

Page 26: Chapter 4

Twisted-pair cabling Network

Page 27: Chapter 4

Twisted-pair cabling Network

An RJ-45 Connection

Page 28: Chapter 4

The RJ-45 jack on a hub is DCE (data communications equipment).

The jack on a computer’s NIC is DTE (data terminal equipment).

Twisted-pair cabling Network

Page 29: Chapter 4

Twisted-pair cabling Network

Communication is not possible between DCE-DCE / DTE-DTE

devices using twisted-pair/RJ-45 cable with the following wiring.

Page 30: Chapter 4

Twisted-pair cabling Network

A crossover cable with the following wiring compensates for this

shortcoming.

Page 31: Chapter 4

Twisted-pair cabling Network

Twisted-pair performance designations.

Page 32: Chapter 4

Twisted-pair cabling Network

 

Plenum Vs. Non-Plenum cable

Page 33: Chapter 4

Coaxial cable

Most of the cable is the thin variety (RG-58), used with Thin

Ethernet.

Some may use the thicker cable (RG-8) for Thick Ethernet.

Page 34: Chapter 4

Coaxial cable

Thin Ethernet cabling is:

Wired in a bus arrangement.

Uses BNC connectors.

Page 35: Chapter 4

Coaxial cable

Page 36: Chapter 4

INSTALLING AND MAINTAINING NETWORK CABLING

Cable plant installation should include:

Proper cable and connectors.

Complete labeling of all parts.

As-built drawing of cabling routes and locations.

Certification report for installed cables.

Education for bus-type Network users about the coaxial cable.

Page 37: Chapter 4

Choosing a cabling contractor

How will the contractor document the cable plant?

What are his/her documentation standards?

Will s/he provide a set of as-built drawings?

How does the contractor install the cable to avoid electrical

interference sources in the ceiling and walls?

Page 38: Chapter 4

Does the contractor recommend a wiring solution that

combines telecom wiring with data wiring?

Has the contractor done any local installations that you can

view?

Does the contractor provide speedy post-installation

support for new wiring drops?

Choosing a cabling contractor

Page 39: Chapter 4

What equipment does the contractor use to certify the

cable plant?

What certification documentation will the contractor

provide upon completion?

Does the contractor also provide post-installation

troubleshooting services?

Choosing a cabling contractor

Page 40: Chapter 4

Typical problems:

Abnormally slow network performance.

Sporadic disconnections from the Network.

Complete loss of Network connectivity.

Troubleshooting coaxial cable systems is more difficult

because the entire Network is down.

Solving cabling problems

Page 41: Chapter 4

To track unobvious problems:

Use a coaxial cable scanner.

Get an extra terminator for the Network.

Solving cabling problems

Page 42: Chapter 4

The following can be shared:

Printers

High-speed Internet connection

Storage space

Backup devices

SELECTING AND INSTALLING A SOHO NETWORK

Page 43: Chapter 4

Standard Network hardware:

A central hub

Network Interface Card (NIC)

Network cable

Operating System

Selecting a SOHO Network

Page 44: Chapter 4

Phone Line Networks

Power Line Networks

Wireless Networks

Other home Networks

Page 45: Chapter 4

Network topologies:

Bus

Star

Ring

SUMMARY

Page 46: Chapter 4

Network cabling:

Unshielded twisted-pair (UTP)

Shielded twisted-pair (STP)

Coaxial

Fiber-optic cable

Summary

Page 47: Chapter 4

Installing and maintaining Network cabling:

Cable plant installation.

Choosing a cable operator.

Solving cabling problems.

Summary

Page 48: Chapter 4

Selecting a SOHO Network:

Advantages

Standard Network hardware

Other home Networks

Summary