chapter 5 – series circuits
DESCRIPTION
Chapter 5 – Series Circuits. Introductory Circuit Analysis Robert L. Boylestad. 5.1 - Introduction. Two types of current are readily available, direct current (dc) and sinusoidal alternating current (ac) We will first consider direct current (dc). Insert Fig 5.1. Introduction. - PowerPoint PPT PresentationTRANSCRIPT
Chapter 5 – Series Circuits
Introductory Circuit AnalysisRobert L. Boylestad
5.1 - Introduction
Two types of current are readily available, direct current (dc) and sinusoidal alternating current (ac)
We will first consider direct current (dc)
Insert Fig 5.1Insert Fig 5.1
Introduction
If a wire were an conductor (no opposition to flow), the potential difference V across the resistor will equal the applied voltage of the battery
V (volts) = E (volts) Current then is limited only by the resistor (R)
The higher the resistance, the less the current
5.2 - Series CircuitsTwo elements are in series if
They have only one terminal in common The common point between the two elements is not
connected to another current-carrying element
If all elements in the circuit are in series, then the network is called a series circuit
Examples of a series circuit are the tying of small pieces of rope together to form a longer rope and the connecting of pipes to get water from one point to another
Series Circuits
Current is the same through series elements Used to determine if two elements are in series
A branch of a circuit is any portion of the circuit that has one or more elements in series
The total resistance of a series circuit is the sum of the resistance levels
RT = R1 + R2 + R3 + R4 ….+ RN
Series Circuits
Total resistance (RT) is all the source “sees”
Once RT is known, the current drawn from the source can be determined using Ohm’s law:
Since E is fixed, the magnitude of the source current will be totally dependent on the magnitude of RT
Insert Fig 5.5Insert Fig 5.5
Is=ERT
Series Circuits The fact that current is the same through each
element of a series circuit permits a direct calculation of the voltage across each resistor using Ohm’s law
V1 = IR1, V2 = IR2, V3 = IR3, … VN = IRN
The total power delivered to a resistive circuit is equal to the total power dissipated by the resistive elements
Pdel = P1 + P2 + P3 + …+ PN
5.3 - Voltage Sources in Series
Voltage source can be connected in series to increase or decrease the total voltage applied to the system
Net voltage is determined by summing the sources with the same polarity and subtracting the total of the sources with the opposite “pressure”
ET = E2 + E3 - E1 (assuming that E1 has a different polarity than E2 and E3 )
5.4 - Kirchhoff’s Voltage Law
Kirchhoff’s voltage law (KVL) states that the algebraic sum of the potential rises and drops around a closed loop (or path) is zero
Insert Fig. 5.12Insert Fig. 5.12
Kirchhoff’s Voltage Law The applied voltage of a series circuit equals the sum of
the voltage drops across the series elements Vrises = Vdrops
(the sum of the rise around a closed loop must equal the sum of the drop)
The application of Kirchhoff’s voltage law need not follow a path that includes current-carrying elements
When applying Kirchhoff’s voltage law, be sure to concentrate on the polarities of the voltage rise or drop rather than on the type of element
Do not treat a voltage drop across a resistive element differently from a voltage drop across a source
5.5 - Interchanging Series Elements
Elements of a series circuit can be interchanged without affecting the total resistance, current, or power to each element
In the Figures below, resistors 2 and 3 are interchanged without affecting the total resistance
Insert Fig 5.20Insert Fig 5.20Insert Fig 5.19Insert Fig 5.19
5.6 - Voltage Divider Rule The voltage across the resistive elements will divide
as the magnitude of the resistance levels It is the ratio of resistor value that counts when it comes to
voltage division and not the relative magnitude of all the resistors
Voltage Divider Rule (VDR) Permits determining the voltage levels of a circuit without
first finding the current
Vx = RxERT
Voltage Divider Rule The voltage across a resistor in a series circuit is
equal to the value of the resistor times the total impressed voltage across the series elements divided by the total resistance of the series elements
The rule can be extended to voltage across two or more series elements if the resistance includes total resistance of the series elements that the voltage is to be found across
Voltage sources and grounds
Ground symbol with its defined potential
Symbol for voltage source
5.7 - Notation
Notation
Double-subscript notation Because voltage is an “across” variable and exists between two points, the
double-subscript notation define differences in potential The double-subscript notation Vab specifies point a as the higher potential. If
this is not the case, a negative sign must be associated with the magnitude of Vab
The voltage Vab is the voltage at point a with respect to (w.r.t.) point b
Notation
Single-subscript notation The single-subscript notation Va specifies the voltage at point a
with respect to ground (zero volts). If the voltage is less than zero volts, a negative sign must be associated with the magnitude of Va
Notation
General comments If the voltage at points a and b are known with
respect to ground, then the voltage Vab can be determined using the following equation:
Vab = Va - Vb
5.8 - Internal Resistance of Voltage Sources
Every source of voltage (generator, battery, or laboratory supply) has some internal resistance
The ideal voltage source has no internal resistance and an output voltage of E volts with no load or full load
Internal voltage across the internal resistance is computed using the formula: Vint = IFLRint
For any chosen interval of voltage or current, the magnitude of the internal resistance is given by
Rint = VE / IL
5.9 - Voltage Regulation For any supply, ideal conditions dictate that for a
range of load demand (IL), the terminal voltage remains fixed in magnitude
If a supply is set at 12 V, it is desirable that it maintain this terminal voltage, even though the current demand on the supply may vary
Voltage regulation characteristics (VR) are measures of how closely a supply will come to maintaining a supply voltage between the limits of full-load and no-load conditions
Voltage Regulation
Ideal conditions, VFL = VNL and VR% = 0 The smaller the voltage regulation, the less the
variation in terminal voltage with change in load
VR% = (Rint / RL) X 100%
5.10 - Measurement Techniques
For an up-scale (analog meter) or positive (digital meter) reading an ammeter must be connected with current entering the positive terminal and leaving the negative terminal
Ammeters are placed in series with the branch in which the current is to be measured
Measurement Techniques
Voltmeters are always hooked up across the element for which the voltage is to be determined
For a double-script notation: Always hook up the red lead to the first subscript and the black lead to the second.
For a single-subscript notation: Hook up the red lead to the point of interest and the black lead to the ground
5.11 - Applications
Holiday lights Holiday lights are connected in series if one wire
enters and leaves the casing If one of the filaments burns out or is broken, all of
the lights go out unless a fuse link is used A fuse link is a soft conducting metal with a coating on it
that breaks down if the bulb burn out, causing the bulb to be by-passed, thus only one bulb goes out.
Applications Microwave oven
A series circuit can be very useful in the design of safety equipment
In a microwave, it is very dangerous if the oven door is not closed or sealed properly. Microwaves use a series circuit with magnetic switches on the door to insure that the door is properly closed.
Magnetic switches are switches where the magnet draws a magnetic conducting bar between two conductors to complete the circuit.
Applications
Series alarm circuits