chapter 6 options - idec global 6 options 1 communication cables.....6-2 2 replacement...

6-1

Chap.6

Chapter 6 Options

1 Communication Cables..............................................................................6-2 2 Replacement Backlight ............................................................................6-24

2.1 HG1F type..................................................................................................................6-24 2.2 HG2F type..................................................................................................................6-25 2.3 HG3F/4F type ............................................................................................................6-26

3 O/I Link Unit .............................................................................................6-29 4 Digital I/O Unit..........................................................................................6-31

Chapter6 Options

6-2

1 Communication Cables Part Number: HG9Z-XCM22 Maintenance cable for the HG2G, HG2F/2S/3F/4F maintenance port and DOS/V-family personal computers.

Name Pin No. Pin No. Name

Shield Cover Cover Shield

SD 3 3 SD

RD 2 4 RD

DR 6 1 RS

CS 8 8 NC

CD 1 5 DR

ER 4 2 ER

SG 5 7 SG

RS 7 6 EN RI 9

PC D-sub 9P connector

(socket type)

HG2G, HG2F/3F/4F Mini DIN connector

2m

Shield

1 Communication Cables

6-3

Chap.6

Part Number: PF3S-KS1 Communication cable for the HG2F/3F/4F Serial 1 and the IDEC FA-3S SIF2.

Pin No. Name Pin No. Name

FG 1 1 CD

SD 2 2 RD

RD 3 3 TD

RS 4 4 DTR

CS 5 5 GND

NC 6 6 DSR

SG 7 7 RTS

NC 8 8 CTS

ER 20 9 RI

Shield Cover

Cover Shield

HG2F/3F/4F D-sub 25P connector

(plug type)

FA-3S D-sub 9P connector

(socket type)

Shield

5m

Chapter6 Options

6-4

Part Number: FC4A-KC2C Communication cable for the HG2F/3F/4F Serial 1 and the IDEC MICROSmart.

Name Pin No. Pin No. Name

FG 1 1 NC

SD 2 2 NC

RD 3 3 TXD

RS 4 4 RXD

CS 5 5 NC

NC 6 6 CMSW

SG 7 7 SG

NC 8 8 NC ER 20 Cover Shield

Shield Cover


(plug type)

PLC Mini DIN8P connector

Shield

5m


6-5

Chap.6

Part Number: HG9Z-3C115 Connection cable for the HG2F/3F/4F Serial 1 and the IDEC MICRO3.

Name Pin No. Pin No. Name SDA 11 1 D+

SDB 15 2 D-

RDA 10

RDB 16

RS+ 22

RS- 19

CS+ 21

CS- 18 7 0V

SG 7

TERM 9 Cover Shield

FG 1

5m

Shield


(plug type)

MICRO3 Loader Port Mini DIN8P connector

Chapter6 Options

6-6

Part Number: HG9Z-3C125 Communication cable for the HG2F/3F/4F Serial 1 and the IDEC MICRO3C and OpenNet Controller, MicroSmart.

Name Pin No. Pin No. Name FG 1 1 RS

SD 2 2 ER

RD 3 3 SD

RS 4 4 RD

CS 5 5 DR

NC 6 6 SG

SG 7 7 SG

NC 8 8 +5V

ER 20 Cover Shield

Shield Cover

Shield

5m


(plug type)



6-7

Chap.6

Part Number: HG9Z-3C135 Communication cable for the HG2F/3F/4F Serial 1 and PLC (RS-232C, D-sub 25P, Mitsubishi and Omron Link Units).

Name Pin No. Pin No. Name FG 1 1 FG

SD 2 2 SD

RD 3 3 RD

RS 4 4 RS

CS 5 5 CS

NC 6 6 DR

SG 7 7 SG

NC 8 8 CD

ER 20 20 SG

Shield Cover

Cover Shield

Shield

5m


(plug type)

PLC D-sub 25P connector

(plug type)

Chapter6 Options

6-8

Part Number: HG9Z-3C145 Communication cable for the HG2F/3F/4F Serial 1 and PLC (RS-232C, D-sub 9P, Mitsubishi Link Units).

Name Pin No. Pin No. Name FG 1 1 RS

SD 2 2 ER

RD 3 3 SD

RS 4 4 RD

CS 5 5 DR

NC 6 6 SG

SG 7 7 SG

NC 8 8 +5V

ER 20 Cover Shield

Shield Cover

5m

Shield


(plug type)


(plug type)


6-9

Chap.6

Part Number: HG9Z-3C155 Communication cable for the HG2F/3F/4F Serial 1 and PLC (RS-232C, D-sub 9P, Omron CPU Unit RS-232C I/F).


SD 2 2 SD

RD 3 3 RD

RS 4 4 RS

CS 5 5 CS

NC 6 6

SG 7 7

NC 8 8

ER 9 9 SG

Shield Cover

Cover Shield

5m

Shield


(plug type)


(plug type)

Chapter6 Options

6-10

Part Number: HG9Z-3C165 Communication cable for the HG2F/3F/4F Serial 1 and Mitsubishi A and FX Series Programming Port.

Name Pin No. Pin No. Name SD+ 11 2 RD+

SD- 15 15 RD-

RD+ 10 3 SD+

RD- 16 16 SD-

RS+ 22 4 CS+

RS- 19 17 CS-

CS+ 21 5 RS+

CS- 18 18 RS-

SG 7 7 SG

TERM 9 8 SG

FG 1 20

Shield Cover

21 Cover Shield

5m

Shield


(plug type)


(plug type)


6-11

Chap.6

Part Number: FC2A-KP1C

Communication cable for the Serial 2 and printer/external devices and PLC.

Pin No. Color

1 Black

2 Yellow

3 Blue

4 Green

5 Brown

6 Gray

7 Red

8 White

Cover

2.5m

Shield

Mini DIN8P connector

The following wiring is for the HG2F/2S/3F/4F Serial 2 and printers only.

Refer to the printer instruction manual for details.

Name Color Pin No.

Shield － Cover

SD Blue 3 RxD Date reception

SG Red 7 GND Ground

DR Brown 5 DTR or RTS Data send request

ER Yellow 2

EN Gray 6

Name

HG2F/2S/3F/4F

Mini DIN8P conector

Shield

Printer

Shield

Refer to the communication cable (HG9Z-XC275) for the HG2G and PLC.

Terminate any unused wires properly to make sure that these wires do not contact other wires or

metal parts electrically.

Chapter6 Options

6-12

Part Number: FC4A-KC1C Communication cable for the HG1F(RS-232C type) Serial 1 and the IDEC MICROSmart Programming Port.

Name Pin No. Pin No. Name FG 1

SD 2 4 RD

RD 3 3 SD

DR 6

ER 9

SG 7 6 CMSW

7 GND

Cover Shield

5m

Shield

HG1F D-sub 9P connector

(plug type)



6-13

Chap.6

Part Number: HG9Z-XC115 Communication cable for the HG1F(RS-232C type) Serial 1 and the IDEC FA-3S SIF2.

Name Pin No. Pin No. Name FG 1 1 CD

SD 2 2 RD

RD 3 3 TD

DR 6 4 DTR

ER 9 6 DSR

7 RTS

8 CTS

9 RI

SG 7

5 GND

5m

Shield


(plug type)


(socket type)

Chapter6 Options

6-14

Part Number: HG9Z-XC145 Communication cable for the HG1F(RS-232C type) Serial 1 and PLC (RS-232C, D-sub 25P, Mitsubishi Computer Link Unit).


SD 2 3 RD

RD 3 2 SD

DR 6 20 DTR

ER 9 5 CS

6 DSR

8 CD

4 －

SG 7

7 SG

5m

Shield


(plug type)


(plug type)


6-15

Chap.6

Part Number: HG9Z-XC155 Communication cable for the HG1F(RS-232C type) Serial 1 and PLC (RS-232C, D-sub 25P, Omron Host Link Unit).


SD 2 3 RD

RD 3 2 SD

DR 6 4 RS

ER 9 5 CS

6 DR

20 ER

8 －

SG 7

7 SG

5m

Shield


(plug type)


(plug type)

Chapter6 Options

6-16

Part Number: HG9Z-XC183 Communication cable for the HG1F(RS-232C type) Serial 1 and the IDEC OpenNet Controller and MICROSmart Port2.

Name Pin No. Pin No. Name Shield Cover Cover Shield

SD 2 4 RD

RD 3 3 SD

DR 6 2 ER

ER 9 5 DR

6 SG

SG 7 7 SG

1 RS

FG 1

8 +5V

3m

Shield


(plug type)



6-17

Chap.6

Part Number: HG9Z-XC203 Communication cable for the HG1F(RS-232C type) Serial 1 and PLC (RS-232C, D-sub 9P, Mitsubishi Computer Link Unit).

Name Pin No. Pin No. Name FG 1 1 CD

SD 2 2 RD

RD 3 3 SD

DR 6 4 ER

SG 7 5 SG

ER 9 6 DR

7 RS

8 CS

9 －

3m

Shield


(plug type)


(plug type)

Chapter6 Options

6-18

Part Number: HG9Z-XC213 Communication cable for the HG1F(RS-232C type) Serial 1 and PLC (RS-232C, D-sub 9P, Omron CPU Unit RS-232C I/F except for C20H/28H/40H).


SD 2 3 RD

RD 3 2 SD

DR 6 4 RS

ER 9 5 CS

SG 7 9 SG

3m

Shield


(plug type)


(plug type)


6-19

Chap.6

Part Number: HG9Z-XC245 Communication cable for the HG1F(RS-485/422 type) Serial 1 and the Mitsubishi FX Series.

Name Pin No. Pin No. Name SDA 1 2 RDA

SDB 6 1 RDB

RDA 2 7 SDA

RDB 7 4 SDB

SG 5 3 SG

RSA 3 6 SG

CSA 4

RSB 8

CSB 9

Cover FG

FG Cover

5m

Shield


(plug type)


Chapter6 Options

6-20

Part Number: HG9Z-XC255 Communication cable for the HG1F(RS-485/422 type) Serial 1 and the Mitsubishi A/QnA Series.

Name Pin No. Pin No. NameSDA 1 2 RDA

SDB 6 15 RDB

RDA 2 3 SDA

RDB 7 16 SDB

SG 5 7 SG

8 SG

RSA 3 4 CSA

RSB 8 17 CSB

CSA 4 5 RSA

CSB 9 18 RSB

20

FG Cover

21 Cover FG

5m

Shield


(plug type)


(plug type)


6-21

Chap.6

Part Number: HG9Z-XC265 Communicate cable for the HG1F (RS-232C type) Serial 1 and the Mitsubishi Q Series.

Name Pin No. Pin No. Name FG 1

SD 2 1 RD(RXD)

RD 3 2 SD(TXD)

DR 6 6 DTR(ER)

SG 7 3 SG

ER 9 5 DSR(DR)

5m

Shield


(plug type)


Chapter6 Options

6-22

Part Number: HG9Z-XC275

Communication cable for the HG2G (RS-232C type) Serial 1 and the IDEC MICROSmart or the Mitsubishi

FX Series.

Pin No. Color

1 Black

2 Yellow

3 Blue

4 Green

5 Brown

6 Gray

7 Red

8 White

Cover

5m

Shield


The following wiring is for the HG2G and the IDEC MICROSmart.

Name Color Pin No. Pin No. Name

NC Black 1 1 SD

NC Yellow 2 2 RD

SD Blue 3 3 RS

RD Green 4 4 CS

NC Brown 5 5 SG

SG Gray 6

SG Red 7

NC White 8

Shield - Cover

Shield

PLC (RS-232C)


HG2G (RS-232C) Terminal


6-23

Chap.6

The following wiring is for the HG2G and the Mitsubishi FX Series (except the FX3U and FX3UC-32MT-LT).

Name Color Pin No. Pin No. Name

SDA Red 7 8 RDA (RD+)

SDB Green 4 9 RDB (RD-)

RDA Yellow 2 6 SDA (SD+)

RDB Black 1 7 SDB (SD-)

SG Blue 3 5 SG

SG Gray 6

Shield - Cover

PLC (RS-485/422)


HG2G (RS-485/422) Terminal

Terminate any unused wires properly to make sure that these wires do not contact other wires or

metal parts electrically.

Please do not use HG9Z-XC275 because there is the case that the housing of FX3U/

FX3UC-32MT-LT and a part of it interfere.

Chapter6 Options

6-24

2 Replacement Backlight

2.1 HG1F type Model: HG9Z-1FB (Backlight for HG1F only)

Replacing the Backlight Make sure to turn off the power to the HG1F

before replacing the backlight; otherwise, product failure, electric shock, or fire may occur. Make sure to protective gloves when replacing the backlight.

Follow the procedures below to replace the

backlight. 1 Turn off the power to the HG1F and disconnect

the cable. 2 Unlock the 4 tabs securing the back case, and

remove the rear case.

3 Remove the connector that is connected to the

PWB. 4 Pull out the backlight while lifting the tab of the

backlight holder. 5 Install the replacement backlight by reversing the

procedures in Step 4. 6 Connect the connector for the replacement

backlight. 7 Align the 4 tabs on the back case and close the

case.

コネクタを矢印方向に取り外す。

コネクタConnector

バックライトホルダー爪


6-25

Chap.6

2.2 HG2F type Model: HG9Z-2B1 (Backlight for HG2F only)

Replacing the Backlight

Before attempting to replace the backlight, be certain to disconnect the power supply. Wear protective gloves when replacing the backlight.

1 Switch off the main unit power supply and disconnect the power cable.

2 Remove the M3 screws from the four corners of the main unit rear panel.

3 Disconnect the backlight cable from the back case and open the front and back cases.

Do not pull the cable in order to disconnect the connector. Pull the connector instead. When opening the case, do not disconnect the flat cables.

4 Press the lock tab at the lower right of the LCD module, and lift the backlight to remove.

5 Install the replacement backlight by reversing the

procedures in Step 4.

6 Reverse the procedures in Step 3 to connect the

connector and front and back cases. Then tighten the four screws on the back panel. Confirm that the alignment catches at the top and bottom of the case are inserted into their respective notches. (Tighten four screws on the corners to a torque of 0.6 to 0.7 N·m.) Tab of the backlight holder

Flat cable

LCD module

Tab

Backlight

Chapter6 Options

6-26

2.3 HG3F/4F type Model: HG9Z-3FB (Backlight for HG3F only) HG9Z-4FB1 (Backlight for HG4F only) The HG4F uses two different types of replacement backlights depending on the production date. When ordering a replacement backlight, look for the Replacement Backlight Type No. label on the back of the HG4F. For the label position, refer to Chapter 2, “2 Part Names and Functions”. If the label is not found, specify HG9Z-4FB1.

Replacing the Backlight

Before attempting to replace the backlight, be certain to disconnect the power to the screen. Wear protective gloves when replacing the backlight.

Make sure the surrounding environment is clean. Take extra precautions during this process. Dust particles may enter the touch panel when replacing the backlight. When in doubt please ask your sales representative.

1 Switch off the main unit power supply and

disconnect the power cable. 2 Remove the screws from the main unit rear panel,

and carefully separate the back and front cases.

HG3F type (1) M3 four screws (2) M3 two tapping screws HG4F type (1) M3 four screws (2) M3 four tapping screws

(1) (1) (2)

Lift window to remove backlight

(1) (2) (1)

Lift window to remove backlight


6-27

Chap.6

3 Peel the protective film off the window.

4 Remove backlight cable from the inverter module.

Inverter module and connector positions are different depending on the model (HG3F and HG4F).

Please take extra precautions when performing these tasks.

HG3F type

The protective film

Backlight connector

Chapter6 Options

6-28

HG4F type 5 Push down on the tab and pull the backlight out.

HG3F type HG4F type 6 Install the replacement backlight by reversing the

procedures in Step 5.

7 Reverse the the procedures in Step 4 and then Step 3 to connect the connector and reapply the protection film.

8 Reverse the procedures in Step 2 to connect the front and back cases, then tighten the screws on the back panel.

Take extra care during this process. Otherwise, dust particles may enter between a surface sheet and a touch panel during backlight exchange.

Backlight connector

3 O/I Link Unit

6-29

Chap.6

3 O/I Link Unit Model: HG9Z-2G1 Outline This special-purpose communication unit is required for O/I Link communication.

External View and Part Names The external view and part names for the O/I Link Unit are given below.

No. Name Function

(1) Terminal RS-485 terminal block (two wire)

(2) Connector For the HG2G, HG1Ｆ

/2F/3F/4F connector

Name Description A Signal line A side B Signal line B side SG Signal ground

Installation on the HG2G, HG1F/2F/3F/4F The HG9Z-2G1 is attached to the back of the HG2G, HG1F/2F/3F/4F. 1 On the back of the touchpanel remove the

label "To use the option unit, remove this sticker".

2 Insert the HG9Z-2G1.

Insert the HG9Z-2G1 so that it clicks securely into the connector.

O/I Wiring The master and slave O/I Link Units are connected using an RS-485 (two wire) bus connection (see the diagram on the following page). The tightening torque for the terminal block screws should be from 0.22 to 0.25Nm. Specifications The O/I Link Unit specifications are as follows. Electrical specifications EIA RS-485 Transmission speed 38400, 57600, 115200bpsSynchronization Asynchronous Communication method

Half duplex

Protocol Dedicated protocol Transmission distance 200m Connection format 1:N Recommended cable 0.3mm2 Twisted-pair

shielded cable Conductor resistance:85Ω/km maximum Shield resistance:20Ω/km maximum

Refer to the Host Interface manual and Instruction manual for further details.

O/I Link

①

②

19.9

30.6

4.1 9.015.8

SG B A

TYPE:HG9Z-2G1

１

２IDEC

Chapter6 Options

6-30

HG2G, HG1F/2F/3F/4F O/I Link Wiring Diagram

Master Slave 1 Slave 2

O/I Link Unit O/I Link Unit O/I Link Unit

A B SG A B SG A B SG

HG2G, HG1 F/2F/3F/4F O/I Link Wiring Master Slave 1 Slave 2

PLC

PLC-link communication O/I Link communication

The HG2S can only be operated as a slave. The O/I link communication protocol of the HG2G is different from that of the HG1F/2F/2S/3F/4F. Refer to the O/I link section of the manual for furter details.

4 Digital I/O Unit

6-31

Chap.6

4 Digital I/O Unit Model: HG9Z-2P101(for HG2F only) HG9Z-3P102(for HG3F/4F only) A digital I/O unit in required when digital input or output is needed .

External View and Part Names The external view and part names for the Digital I/O Unit are given below.

Name Description QuantityExpansion Bus Cable Connector cable 1 I/O Connector PF3S-JF1 2 Mounting Screw - 2

Installation: Install the digital I/O unit to the rear of the operator interface, as shown in the figure below. 1 Place the digital I/O unit to the back of the

operator interface. Put the two latches into the holes.

2 Fasten screws to a proper tightening torque of 0.3 to 0.5 N･m.

3 Insert one side of the Expansion bus cable to the interface connector of the digital I/O unit. The other side of the cable is inserted in the expansion interface of the operator interface. (Before installing the digital I/O unit, read the operating instructions.)

Wiring Make the wiring as short as possible and run all wires as far away as possible from high-voltage and high-current cables. Follow all the procedures and precautions when wiring the digital I/O unit. Connecting to Input and Output Connectors Applicable connector: I/O connector (attached) or rectangular connector FCN-360 made by FUJITSU TAKAMIZAWA COMPONENT LIMITED. Pin assignment is illustrated on the following page.

TYPE:HG9Z-2P102V ist inaLOT No. ********

RERATED IN 12-24V 5mA(at 24VDC)RERATED OUT 12-24V 30mA/PT(480mA/COM)

idec IDEC IZMI CORP.JAPAN

OUTIN

138

32

100

26

Expansion bus cable

(attached) Input connector Output connector

I/O connector (attached)

①

②

③

Chapter6 Options

6-32

Input Pin No.

Function NamePin No.

Function Name

1 Input 1 IN_1 13 Input 9 IN_9 2 Input 2 IN_2 14 Input 10 IN_103 Input 3 IN_3 15 Input 11 IN_114 Input 4 IN_4 16 Input 12 IN_125 Input 5 IN_5 17 Input 13 IN_136 Input 6 IN_6 18 Input 14 IN_147 Input 7 IN_7 19 Input 15 IN_158 Input 8 IN_8 20 Input 16 IN_16

9 Input Common

IN_ COM

21 Input Common

IN_ COM

10 − − 22 − − 11 − − 23 − − 12 − − 24 − − Input Internal Circuit DC inputs can be connected in either polarity.

Output Pin

No.Function Name

Pin

No. Function Name

1 Output 1 OUT_1 13 Output 9 OUT_9


0


1


2


3


4


5


6

9 Output

Common

OUT_C

OM 21

Output

Common

OUT_

COM

10Output

+V OUT_V 22

Output

+V

OUT_

V

11 − − 23 − −

12 − − 24 − −

Output Internal Circuit

12 11 10 9 8 7 6 5 4 3 2 1

24 23 22 21 20 19 18 17 16 15 14 13

Top Pin No.

Under Pin No.

The illustration above is a front view of the input or output connector on the digital I/O unit.

IN_COM

IN_1-16

OUT_1-16

OUT_V

OUT_COM

Fuse

4 Digital I/O Unit

6-33

Chap.6

Specifications Input Points 16 Rated Input Voltage

12 to 24V DC Voltage range: 10 to 28V DC

Isolation Photocoupler isolated Input Impedance

4.7 kΩ

Input Current Approx. 5mA (Input voltage: 24V DC)

Inpu

t

Input Voltage Level

ON voltage: 8V or more OFF voltage: 4V or less

Output Points 16 Rated Load Voltage

12 to 24V DC

Operating Load Voltage Range

10 to 28V DC

Isolation Photocoupler isolated Output Type NPN open collector ON Voltage 1.6V maximum

Out

put

Maximum Load Current

30 mA per output point Max. 200 mA total

Rated Operating Voltage

Supplied from the operator interface

Configuration Connected to the operator interface with the attached expansion bus cable. Installed on the operator interface and fastened with screws.

Dimensions (mm) 138×100×32 Weight (approx.) 120g

Refer to the operator interface user’s manual for further details.

chapter 6 options - idec global 6 options 1 communication cables.....6-2 2 replacement...

Documents