chemline · 2019. 11. 14. · multi port ball valves the chemline type 23 multi port ball valve...

ValvesPiping

Flow Meters& Controls

Materials of Construction

Ball Valves

Butterfly Valves

Diaphragm Valves

Check Valves

Other Valves

Strainers

Chemline

• P V C • C P V C • P P • P V D F • F R P • P P G • P D C P D •

M a n u a l T h e r m o p l a s t i c V a l v e s

Chemline Technical ResourcesManual Thermoplastic Valves CatalogueActuation & Actuated Valves CatalogueControls & Flow Meters CatalogueDigiflowFlowX3® Flow Meters & Instrumentation CatalogueChemical Resistance GuideSpecification Guide

▼▼

▼▼

▼▼

Your Pipeline To Quality

Pressure rated to 230 psi● Provides a high factor of safety

Integral Actuator Mounting Platform● Actuation is easy. Electric or pneumatic actuators

may be mounted in the field.

Full Port● High capacity and low pressure drops

Fully Blocking● Downstream union nut may be safely

disassembled for piping maintenance while valveis closed off under full system pressure

Built-In Spanner Wrench● Top of the handle is designed to be used as a tool

for accessing internal parts

Safety Shear Stem Design● Stem has double o-rings● Designed to hold full pressure even if stem breaks

due to excessive torque

High Chemical Resistant Material● PVC and CPVC compounds have an “A” chemical

resistance rating as per ASTM D-1784. They haveoutperformed other PVC and CPVC compounds onaggressive chemicals.

230 psi Working Pressure

NSF 61 Certified5

Double Stem O-Rings for Safety

1Butt ends for fusion to Chemline metric PP or PVDF piping.2Other materials are available special order.3CPE = Chlorinated Polyethylene.4PVC, CPVC and PVDF 1/2" to 2" are rated at 230 psi;2-1/2" to 4" and all size PP valves are rated at 150 psi at 20oC.

5PVC valves with EPDM or FKM (Viton®) seals are certified underNSF/ANSI Standard 61 for contact with drinking water.

Features

Type 21 True UnionBall ValvesThe Chemline Type 21 True Union Ball valveincorporates state of the art features andperformance. This is a full port, full blocking TrueUnion valve pressure rated at 16 bar (230 psi)4.Double stem o-rings are provided for safety.Pneumatic or electric actuator mounting is easilyaccomplished in the field – Just pull off the handleto reveal an integral ISO mounting platform.Optional threaded inserts in the base are availablefor anchoring the valve.

PVC,CPVC,PP,PVDFSERIES: Type 21

SIZES: 3/8" – 4"

ENDS: Socket, Threaded, Flanged,Butt or ChemFlareTM

SEATS: Teflon® PTFE

SEALS1: EPDM, FKM (Viton®), CPE2


Weldless Design● Eliminates all fusion welds and glued joints● Threaded connection between flared end and

tube nut is not wetted

Easy Installation● Flaring the tube ends is easy ● Assembly is by hand2

Low Down Time● No welding or curing waiting time. The system

may be pressure tested immediately.

Minimum Dead Volume● The flared tubing connection has minimum dead

volume desirable on sodium hypochlorite andultrapure applications

1For sodium hypochlorite applications Chemline recommends venting ball valves bydrilling a hole on the upstream side of the ball in the closed position.

2ChemFlareTM fitting nuts should be hand tightened only.Use of a wrench can result in excessive tightening and stripped threads.

Features

Full Valve Working Pressure

Easy Installation

Low Down Time

PVC, CPVC, PP, PVDFSERIES: ChemFlareTM

SIZES: 1/2", 3/8", 3/4" and 1"

ChemFlareTM

End ConnectorsAll Chemline valves with True Union ends areavailable with ChemFlareTM end connections.ChemFlareTM is a long term leak-free connectiondesign for difficult applications such as sodiumhypochlorite1. These flared end connections are easyto install and allow for compact plumbing and asmall footprint.

They are available on Chemline True Union valves,flow meters and controls up to1" and will connectTeflon® PFA tubing down to 1/4" size.

Tubing must be flared using a mechanical flare toolor by heating and using a forming flare tool(preferred method). Consult Chemline for flaretools.


Pressure rated to 230 psi● Provides a high factor of safety

Full Port● High capacity and low pressure drops

Fully Blocking● Downstream union nut may be safely

disassembled for piping maintenance whilevalve is closed off under full system pressure

Built-In Spanner Wrench● Top of the handle is designed to be used as a

tool for accessing internal parts

Compatible with Safe-Bloc® Ball Valves● 1/2", 1-1/4" and 2" sizes can easily replace old

Safe-Bloc® True Union ball valves. The bodysections are interchangeable in these sizes only.

230 psi Working Pressure

NSF 61 Certified1

Double Stem O-Rings for Safety

Features

Type 26Ball ValvesThis is a full port, full blocking True Union valvepressure rated at 16 bar (230 psi). Double stemo-rings are provided for safety. The bodies areinterchangeable with the old Safe-Bloc® valves inseveral sizes.

Replace Safe-Bloc®?

Yes

No

No

Yes

No

Yes

Size

1/2"

3/4"

1"

1-1/4"

1-1/2"

2"

1Valves are certified under NSF/ANSI Standard 61 for contact with drinking water.

PVCSERIES: Type 26

SIZES: 1/2" – 2"

ENDS: Socket


SEALS: EPDM


Compact BallValvesChemline Compact Ball Valves are manufactured to thesame high quality standards to the Type 21 True Unionball valve. They are used on applications where union endvalves are not necessary or desired such as drain valves fortanks. They are also lower cost and more compact. TheType 21 True Union ball valve although more expensivethan the Compact type, are preferable for chemical andseawater services where easy in-line servicing and partsreplaceability is required.

Features Heavy Duty HandleBreakage eliminatedEasy Operation

Unique cushioned Teflon® SeatsEnsures low stem torquesEasy to open and close

Thick, solid StemNo breakage

Available with Electromni® Electric Actuator

Floating BallSuperior to one-pieceball and stem designMachined for long cycling life

Low Cost

Rugged

NSF 61 Certified1

All PVC or all CPVC Construction● Handles are colour coded red for PVC,

blue for CPVC

High Chemical Resistance● The PVC as well as CPVC compounds for these

valves have an “A” chemical resistancerating2 – superior to competition

Full Port● Low pressure loss

Low Stem Torques● Due to floating ball

design and cushioned Teflon® seats

Compact● Space saving

1Valves are certified under NSF/ANSI Standard 61 for contact with drinking water.2Designation for chemical resistance as per ASTM D-1784.

PVC, CPVCSERIES: OM

SIZES: 3/8" – 3"

ENDS: Threaded, Socket


STEM SEAL: EPDM


Type 23Multi PortBall ValvesThe Chemline Type 23 Multi Port Ball Valve incorporatesall the quality features of the Type 21 True Union type.One Multi Port valve eliminates the need for twostandard ball valves and a tee in many cases.

A choice of several flow patterns is available. L-Port issupplied standard. X-Port offers flow straight throughports ➀ and ➁. T-Port connects all three portssimultaneously.

Features

Integral Actuator Mounting Platform● Actuation is easy. Electric or pneumatic actuators

may be mounted in the field5

Fully Blocking● Downstream union nut may be safely disassembled

for piping maintenance while valve is closed offunder full system pressure

● Handle works as a tool for accessing internal parts

Safety Shear Stem Design● Stem has double o-rings● Designed to hold full pressure even if stem breaks

due to excessive torque

High Chemical Resistant Material● PVC and CPVC compounds have an “A” chemical

resistance rating as per ASTM D-1784.

● Bidirectional flow is permitted

Choice of Flow Patterns

Easy to Actuate in the Field

NSF 61 Certified4

1 2

3

1Butt ends for fusion to Chemline metric PP or PVDF piping.2 For ChemFlareTM end connectors, consult Chemline.3 Other seal materials are available special order.4 PVC valves with EPDM or FKM (Viton®) seals are certified under NSF/ANSI Standard 61 for contact with drinking water.5 For operation with pneumatic actuators, 90o operating ball is recommended.

Three Positions of L-Port Operation:

1. Port ➀ and ➂ open, as illustrated2. Shut-off – handle turned 90°3. Port ➁ and ➂ open – handle turned 180°

Three Positions of X-Port Operation:● No Shut-off is possible with X-Port● Available 1/2" to 2" only

1. Port ➀ and ➂ open, as illustrated2. Flow through ➀ and ➁ – handle turned 90°3. Port ➁ and ➂ open – handle turned 180°

Two Positions of 90o Operation:● Required for pneumatic actuation

1. Port ➀ and ➂ open, as illustrated2. Port ➁ and ➂ open – handle turned 90°

Two Positions of T-Port Operation:

1. Port ➀, ➁ and ➂ open2. Shut-off – handle turned 90°

PVC, PP, CPVC, PVDFSERIES: Type 23

SIZES: 1/2" – 4"

ENDS: Socket, Threaded, Flanged,Butt1 or ChemFlareTM2


SEALS: EPDM, FKM (Viton®)3


High Capacity6" Ball ValvesChemline HC Series is a true large port 6" ballvalve manufactured in PVC, polypropylene andPVDF. Most other 6" valves often are 4" with endsincreased to 6". HC Series offers an unobstructedfull port which allows passage of mechanical pipecleaners or “pigs”. Applications include unfilteredsea water and sewage lines. It is also suitable formild slurries and vacuum lines.

Features

Large Port● Low Pressure Loss – Cv value of 1880● No Obstruction to Flow – No possible hangup of

debris. Suitable for lines where “pigging” isrequired.

● Low Fluid Velocities – Minimal line velocityincrease through these valves means lower abrasionif solids are present.

Compact Dimensions● Minimum end-to-end length

Easy Maintenance● The body is a lugged cartridge which slips out of

line when the end flange bolts are removed

Light Weight● Easy installation● Minimal stress on piping system

No Cavity between Body and Ball● The low dead volume eliminates sediment build-up

Cushioned Teflon® Ball Seats● Elastomer cushions provide a good closure seal and

smooth operation

Teflon® Stem and Trunion Bearings● Assure low torque and maintenance free operation

Available Flanged to 8"● The Cv value of these valves flanged to 8" is

approximately equal to that of an 8" butterfly valvebut offers no obstruction in flow path

Full Flow Path

Low Stem Torque

Trunion Design

1 8" size is a 6" valve with 8" flanged ends.2Butt ends for fusion to Chemline metric PP or PVDF piping.

Slotted Top SurfaceFor easy actuator mounting

PVC, PP, PVDFSERIES: HC

SIZES: 6" & 8"1

ENDS: Socket, Flanged or Butt2


SEALS: EPDM, FPM (Viton®)

Large SizeCompact 4"& 6”Ball ValvesChemline SL Series Compact Ball Valves are molded-in-place full port 4" and 6", available in PVC with apolyethylene ball. The 6" size is a full port alternativeto a 4" ball valve with ends increased to 6". Seats areTeflon® for long life and low stem torques. The 4" sizeis also available with Hypalon® seats, superior onsustained vacuum applications and many slurries.


Full Port

Compact Dimensions

Abrasion Resistant

1Standard seats are Teflon®. Hypalon® is available in 4" only.

Features

Large Port● Low Pressure Loss – 6" has Cv value of 1880● No Obstruction to Flow – No possible hangup of debris

– Suitable for lines where “pigging” is required

Compact Dimensions – Minimal flange face-to-facedimensions: 6" has 10-1/2" face-to-face length● Will fit where other ball valves will not● The most compact 4" and 6" flanged ball valves

available

Light Weight● Easy installation● Minimal stress on piping system

No Cavity between Body and Ball● The low dead volume eliminates sediment build-up

Teflon® Ball Seats● Provide long life and low stem torques

Long Term Vacuum Resistance● Optional Hypalon® seats (4" only) hold vacuum long term

Abrasion Resistant● PE ball provides superior abrasion resistance● Optional Hypalon® seats (4" only) out perform Teflon® on

abrasion

No Flange Gaskets Required● Flange face O-rings are included

PVC with PE BallSERIES: SL

SIZES: 4" & 6"

ENDS: Flanged

SEATS: Teflon® PTFE, Hypalon® (CSM)1

SEALS: FPM (Viton®), EPDM


MeteringBall ValvesChemline SM Series Metering Ball Valve isdesigned for fine flow control of chemicals orclean fluids. The ball is solid with graduatedv-groove cut on the outside surface. Preciselinear flow control is accomplished through180o rotation of the handle. With apositioning electric actuator, this becomes aninexpensive control valve.

Features

Low Cost

Fine Flow Control

1Butt ends for fusion to Chemline metric PP or PVDF piping.2For ChemFlareTM end connectors, consult Chemline.

Full Size Range● 6 valves sizes 1/2" to 2" offers a large

selection of Cv values

Integral Scale● 5o increments from 0o up to 180o

● Fine linear control

High End Ball Valve Features● Full Blocking design● Double Stem O-Rings for safety● Built in Tool for valve disassembly● Teflon® seats with elastomer cushion

– Automatically compensates for seat wearor expansion

● 230 psi pressure rated (PVC)

Low Stem Torques● Due to floating ball design and cushioned

Teflon® seats

Compact● Space saving

Integral Scale with 5o Increments● Fine flow control and settable flow rates

Handleis tool for valvedisassembly

PVC, PPSERIES: SM

SIZES: 1/2" – 2"

ENDS: Threaded, Socket, Butt1

or ChemFlareTM2


O-Rings: EPDM, FPM (Viton®)

Elastomer SeatedButterfly ValvesChemline elastomer seated butterfly valves up to 24"have been improved. The new Type 57 replaces Type 56up to 14". Type 57 body, disc and seat have beenredesigned to offer better flow characteristics and lowertorques. Stem torques are unaffected by excessive flangebolt torques. New frp gear operators are available. Valvesup to 16" have top flange with standard ISO 5211mounting platform and shaft dimensions for easyactuation. A large selection of body, disc and seatmaterials permit these valves into a wide range of on/offand throttling control applications.

Features

Features – New Type 57

Compact and Light Weight

High Corrosion Resistance● Solid plastic body, disc and hand lever● FRP gear operators are weather resistant to

IP67 enclosure rating

Abrasion Resistant● Solid plastic disc● PVDF disc available for high abrasion

resistance

Easy Actuator Mounting● Valves up to 16" have standard ISO 5211

top flange and shaft dimensions

Easily Installed● Full bolt hole circle makes installation

and alignment easy● No flange gaskets are necessary

Better Sealing● Spherical disc/seat seal design offers

effective sealing at lower stem torques,and long life for the seat

Better Flow● Streamlined disc offers higher Cv values

Protection against Flange Bolt OverTightening● Body gussets and new seat design prevent

excessive flange bolt torques from affectingvalve stem torques

Sizes up to 24"

Easy Actuator Mounting

1 Full stainless steel lug bodies are available as an option.

Sturdy PPG Position Lock19 stops for fine flow controlResists high torque loads

Polypropylene Hand LeverLockable

Full Bolt Circlefor easyinstallation

Gussets on BodyPrevent excessivecompression ofseat


Type 57 Butterfly Valve

Elastomer SeatedSIZES: Type 57: 1-1/2" – 14"

Type 56: 16"TB Series: 18" – 24"

BODY TYPE: Semi Lug Wafer 1

MATERIALS:Body: PVC, PP, PVDFDisc: PP (Standard),

PVC, PVDFSeat and O-Rings: EPDM, FKM (Viton®)


Features

New Improved Design

Superior Performance

1 Up to 4" only in CPVC.2 Butt fusion ends are for connection to Chemline PP and PVDF metric piping systems.3 For ChemFlareTM end connectors, consult Chemline.4 Other diaphragm materials are available.

DiaphragmValvesChemline Type 14 (1/2" to 4") and Type 15 (5" and 6")Diaphragm Valves are an improved version of the olderDV Series. The 8" and 10" DV’s are still current design butare now called Type 72. Types 14 and 15 have beenredesigned using modern computer design technology.Improvements are higher pressure resistance, lower handwheel torques to close, better hydraulics (lower pressurelosses) and other features. Tests show Type 14 tooutperform major competitors in resistance to bonnetleakage on tough applications with thermal cycling.

Chemline diaphragm valves have service histories datingback to 1970 operating in some of the toughest chemicalplant applications in Canada. They have proven internaland external corrosion resistance.

This is an excellent throttling valve, and is suited forslurries or viscous liquids. Because of the self-drainingdesign with no dead volume, it is good for sanitary andhigh purity applications. These diaphragm valves offershigher temperature/pressure ratings and chemicalresistance compared to other Chemline valve types.

Excellent Chemical Resistance● Large choice of materials including PVDF bodies and

Teflon® diaphragms for extremely aggressive services

Externally Corrosion Resistant● Plastic bonnet, handwheel, covered and sealed indicator● Bonnet seals protect internal parts from corrosive

environments

High Pressure Resistance● Designed with a high safety factor against leakage● Tight closing with low hand wheel torque● Highest pressure vs. temperature ratings of all plastic

valve types

Designed for Long Diaphragm Life● Standard Travel Stop prevents over-tightening and

excessive stress on diaphragm.● Special design of compressor eliminates point loading of

diaphragm stud, extending life.

Standard Flange Face-to-Face Lengths● Same lengths as ITT plastic lined (1/2" to 2", 3" to 4")

PVC,PP,CPVC1,PVDFSIZES: Type 14: 1/2" – 4"

Type 15: 5" – 6"Type 72: 8" – 10"

ENDS: Flanged: 1/2" – 10"1

True Union Socket,Threaded or Butt2: 1/2" – 2"ChemFlareTM3: 1/2" – 1"

DIAPHRAGMS: EPDM, Teflon®4

Ball FloatValvesThe Chemline BFP Series Ball Float Valve isa cost effective level control device forwater or non-hazardous liquids. The valvemay be mounted through a hole in thetank wall and anchored with the lock nutprovided.

TEMPERATURE RANGE1/2": – 20 to 70ºC (–4 to 158ºF)1", 1-1/2": – 20 to 50ºC (–4 to 122ºF)

FLOW RATESUSGPM WATER Cv VALUES

WORKINGPRESSURES DIMENSIONS INCHES

Outlet

3/8"†1"

1-1/4"

Size

B

1.1

1.9

2.0

D

1.2

2.2

2.4

E

5.0

7.0

9.0

F

7.0

14.5

15.0

G

3.8

6.6

7.8

H

14.75

27.75

32.12

J

0.50

0.75

0.75

K

2.0

5.0

6.0

Inlet

1/2"

1"

1-1/2"

PSI (WaterLevel at "K")

150

100

100

USGPM at1 psi �P

0.67

4.5

7.1

vs. Line Pressure – PSI10 30 50 80

3.0 6.0 7.2 9.6

14.0 28.0 38.0 48.0

24.0 48.0 60.0 74.0† 3-1/2" long delivery tube is supplied on 3/8" valve outlet only.

Features

All Plastic Construction● No corrosion

Easily Maintainable● All parts are replaceable

Adjustable Float Arm● For different tank levels


For Tank Level Control

Will not Corrode

*1", 1-1/2" has PE disc; 1/2" has PP diaphragm† 3-1/2" long delivery tube is supplied on 3/8" valve

outlet only.

PARTS ▲ Recommended Spare Parts

No. Part Pcs. Materials

1 Float/Arm 1 Polypropylene

2 Screw 1 Polypropylene

3 Body Part "A" 1 Polypropylene

4 Body Part "B" 1 Polypropylene

5 Plunger 1 Polypropylene

6▲ Disc* 1 Polyethylene

7▲ Seat 1 Polypropylene

8 Lock Nut 1 Polypropylene

9 Delivery Tube† 1 Polypropylene

PolypropyleneSERIES: BFP

SIZES: 1/2" – 1-1/2"

ENDS: Threaded


Ball Check &Foot ValvesThe economical and versatile Chemline Ball CheckValve is the most popular type of non-return valvesfor pipe sizes under 6". A wide selection of bodyand seat materials, and end connections areavailable for many different applications. It hasgood flow capacity and will handle many slurry andsuspended solid services. This valve works in bothhorizontal and vertical lines. The Foot Valve is forend of line services such as sumps.

Features

● Built-in Union Design – For easy installationand maintenance

● Free Floating Ball – The only moving part

● Uniseat/Seal – Easily removable

● May be used either horizontally orvertically

● Excellent flow characteristics

● Low seating and opening pressures

True Union to 2"

NSF 61 Certified3

Full Port to 4" Size

1 PP and PVDF Butt fusion ends (available 1/2" to 2")connect to Chemline PP and PVDF piping systems.

2 For ChemFlareTM end connectors, consult Chemline.3 PVC valves with EPDM or FKM (Viton®) seals are certified under

NSF/ANSI Standard 61 for contact with drinking water.

Foot Valve has large capacity strainerbasket with 1/8" perforations

True Union Check1/2" to 2" in all materials

Single Union Check1/2" to 4" in PVC2-1/2" to 4" in CPVC, PP and PVDF

PVC,CPVC,PP,PVDFSERIES: BT – True Union Check

BC – Single Union CheckFV – Single Union Foot Valve FT – True Union Foot Valve

SIZES: 1/2" – 4"

ENDS: Threaded, Socket,Flanged, Butt1 or ChemFlareTM2

SEAT/SEALS: EPDM, FKM (Viton®),Teflon® coated FKM (Viton®)


Swing CheckValvesThe Chemline SC Series Swing Check Valve isthe heaviest duty solid plastic non-returnvalve available. The strong one pieceflanged body is suitable for installation inany type of piping, horizontally or vertically.A large choice of body materials and sealsincluding PVDF and Teflon® allow its use inthe most aggressive chemical services.Pressure drop is low due to full flow design.

Features

● Strong, One-Piece Moulded Flanged Body– Suitable for installation in metal piping

● Light Weight

● Large Flow Capacity – Low pressure drop

Low Pressure Loss

Horizontal or Vertical Operation

Heavy Duty Design

* Standard seals are EPDM in PVC, PP valves, Teflon® and PVDF coated EPDM in PVDF valves.† All PVC valve parts are now made of High Impact PVC material.

PVDF Valve – Resists extremely aggressivechemicals

Flanged Body – Strong,one-piece moulded

Large Access Cover – Allowseasy maintenance withoutremoval of valve from line

SS Cover Boltsare only metal parts

PVC†, PP, PVDFSERIES: SC

SIZES: 3/4" – 8"

ENDS: Flanged

SEALS*: EPDM, Teflon®


PW SeriesWafer CheckValvesThe Chemline PW Series Wafer Check Valveoffers high end features at low prices. Thiswafer check does not require a separate spaceror flange gaskets. The large orifice and full flowdesign means low pressure drop. Spring assisteddisc closure is standard as well as an opticalindication of disc open/close position. A largeselection of body materials and elastomers (allNSF 61 approved) allow for a wide range ofapplications.

Features

Large Flow Capacity – Low pressure drop

High Pressure Ratings● 8" is 150 psi rated

NSF 61 Approved● All wetted parts are made from NSF 61 approved resin

Can be Mounted Vertically or Horizontally

Spring Assisted Valve Closing● Field installed springs assist disc closing for silent

operation and to lower hammer on closing● Two different springs installed in three configurations

provide proper disc closing at 45 psi, 100 psi and 150 psiline pressure

Optional Drain Plug● Moulded boss may be tapped for drainage plug

Low Cost

Full Flow Design

High Working Pressures

Position IndicatorOptical indication of all disc positionsclosed to open

Locating Bolt HolesFor easy installationbetween flanges Large Face O-Rings

No need for gaskets

1PPG=Glass Filled Polypropylene

PVC, PP, PPG1, PVDFSERIES: PW

SIZES: 3" – 12"

SEALS: EPDM, FPM (Viton®)


WP SeriesWafer CheckValvesThe Chemline WP Series Wafer Check Valve isa non-return valve ideal for limited spaceinstallations. These valves are economical andavailable for large pipe sizes, 2" to 12" andlarger1. They are available in two versions –with or without disc springs. The spring addsforce for faster, more silent closing.

Features

Compact● Requires little space in piping systems

Light Weight● 10" PP valve weighs only 7 lbs.

Easy Installation● Wafer body slips between standard flanges

High Chemical Resistance● A selection of materials of construction

for every application

Horizontal or Vertical Operation3

Bubble Tight Shut-off● Provided by replaceable O-ring seal

Available With Disc Springs● Faster disc closure reduces amount of back flow

and consequent water hammer● Maximum closure is obtained with low pressure

differential● Recommended for pulsating flows and

horizontal piping

Available Without Disc Spring● For applications where no metals are desired● Lower cost

Low Cost

Compact

Light Weight

1 Valve sizes up to 40" are available special order.2 Teflon® O-rings are PFA encapsulated FPM (Viton®).3 Disc spring should be used for horizontal piping.

PVC, PP, PVDFSERIES: WP

SIZES: 2" – 12"1

SEALS: EPDM, FPM (Viton®), Teflon® 2

SPRING: 316 Stainless Steel, Hastelloy


Gate ValvesThe Chemline CGA Series flanged Gate Valve is anexcellent isolating valve, but is also versatile. Fullyopen it has an unobstructed port and streamlinedseating area, making pressure drop low. Waterhammer can be a problem with quick closing valvessuch as ball and butterfly. Use of this multi-turn, slowclosing valve eliminates water hammer. Unlike metalgate valves, this one may be throttled. The plasticdisc is not subject to erosion by high fluid velocities,and the fully guided plug disc will not chatter. Thisvalve is an excellent choice for underground services.

Features

● Light Weight – Fast and easy to install

● AWWA Flanged Face to Face Dimensionsin sizes up to 8". Can easily replacecorroded steel valves.

Cylindrical Disc and Large Seating Area● High Working

Pressures● Good Abrasion

Resistance

Full Port

NSF 61 Certified1

Ideal for Underground Service

Streamlined Seating Area and Full Port● Low Pressure Drop● Little Sediment

Buildup – SelfFlushing

Sliding plug Disc ofprecision machinedpolypropylene.Smooth fully-guided openingand closing.

Clear polycarbonateIndicator clearly showsvalve position

Non-rising heavyduty PVC Shaftwith moulded-insteel core

Drain PlugOne-piece mouldedFlanged Body is strongenough for undergroundpiping systems

1 PVC valves with EPDM or FKM (Viton®) seals are certified underNSF/ANSI Standard 61 for contact with drinking water.

PVCSERIES: CGA

SIZES: 1-1/2" – 14"

ENDS: Flanged

SEALS: EPDM


Globe ValvesThe Chemline Globe Valve is an economicalthrottling valve. Its heavy duty designprovides for long service life. The in-lineglobe design causes relatively high pressuredrops, however this is a desirable valve dueto its economy and reliability.

Features

● Slow Closing– Prevents water hammer in PVC piping

● Heavy Duty Construction– Long service life

Union Bonnet Design 1/2" – 2"

Slow Closing

An Economical Throttling Valve

* Socket ends are available custom basis. † Other seal materials are available special order.

2-1/2" – 4" Outside Spindle and Yolk Type

PVC, PPSERIES: GV

ENDS: Socket, Threaded*, Flanged

SEALS: EPDM†


LC SeriesLab CocksChemline LC Series Lab Cocks are rugged quarter turnmini ball valves. They are ideal for general use ininstrumentation lines, available at a fraction of the costof comparable stainless steel valves. Other applicationsinclude air lines for aquaculture, for venting gas in pipelines, process sampling and laboratory use.

Features

● Heavy Stems – Rugged construction

● 1/4" Full Bore – Low pressure drop

● Graduation Marks – For flow control

Low Cost

NSF 61 Certified1

Male Thread x Hose

Male Threaded Hose x Hose

Female Threaded

WORKING PRESSURES VS.TEMPERATURE● 150 psi at 0 to 50oC (30 to 120oF)● 15 psi at 60oC (140oF) maximum

VACUUM RATING● 29.9 inches mercury

† ENDS AVAILABLE SPECIAL ORDER● 1/4" or 3/8" Female Thread x Hose● Male Thread x Female Thread – 1/4"x 1/4",

1/4"x 3/8", 1/2"x 1/4" or 1/2"x 3/8"● 1/2" Male Thread x Hose ● Female Threaded – 1/4"x 3/8", 3/8"x 3/8"● Male Threaded – 1/4"x 1/2", 1/2"x 1/2"

DIMENSIONS INCHESEnds

1/4" Male Thread x 3/8" ID Hose

1/4" Female Threaded

1/4" Male Threaded

3/8" ID Hose x Hose

L

3.48

2.80

2.60

4.37

Cv VALUE VS. OPENINGGraduation Mark

Cv Value

1

0.20

2

0.37

3

0.83

4

1.65

x Denotes either E for EPDM seals or V for FKM (Viton®)seals.

1PVC valves with EPDM or FKM (Viton®) seals are certified underNSF/ANSI Standard 61 for contact with drinking water.

PVCSERIES: LC

SIZES: 1/4"

ENDS†: Male Threaded,Female Threaded,Male Thread x Hose,Hose x Hose

SEALS: EPDM or FKM (Viton®) Seats andStem O-Ring

Item No.

LCTHx

LCFTx

LCMTx

LCHHx


LA SeriesLab CocksChemline LA Series Lab Cocks feature Teflon®

seats, FKM (Viton®) O-ring seals and full 1/4"port. All parts are replaceable. The basic valveis male threaded by female threaded. Includedwith each valve are adaptors, plug,o-ring, strap and lockout (see photo) toprovide a variety of end connections. Aneyelet is provided for easy valve tagging.

Features

● 1/4" Full Port – Low pressure drop

● Adaptors Included – The valve along withadaptors provide for several end connections:– Male Thread x Female Thread– Male Thread x Male Thread– Male Thread x Hose Barb

● Optional Adaptor – Optional femalethreaded hose adaptor allows for moreconfigurations:– Hose Barb x Hose Barb– Hose Barb x Female Thread

● Safety Plug with Strap– A safety plug attached to the valve with a

strap is included

● Lockout Device– Handle lockout device for the closed

position is included

Available in PVDF

Adaptors Included

VACUUM RATING● 29.9 inches mercury

Cv VALUE VS. OPENINGOpening

Cv Value

25%

0.31

50%

0.62

75%

0.92

100%

1.23

WORKING PRESSURES PSI

Material0-40°C

32-104°F60°C

140°F80°C

176°F120°C248°F

PVC

PVDF

150

150

30

90

–

35

–

75

100°C212°F

–

60

Standard AdaptorsOptional Adaptor

Temperature Ranges: PVC 0 to 60°C (32 to 140°F),PVDF –40 to 120°C (–40 to 248°F)

Lockout

Hose Adaptor

Strap

Safety Plug

Male Adaptor

PVC, PVDFSERIES: LA

SIZES: 1/4"

ENDS: Male Thread x Female Thread

SEALS: FKM (Viton®)


NeedleValvesChemline N Series Needle Valves aredesigned for fine throttling of corrosive andultrapure fluids at low flow rates. Becausethe seal material is Teflon®, these valves aresuitable for aggressive chemicals where simi-lar valves with elastomer seals will not stand

Features

Precise Control with Fine Adjustment● Precision machined seat and matching

ground needle tip along with a 24 pitch finethread stem (five turns from closed to full-open) provides for excellent flow control.Better control of reagents can meansignificant cost savings.

High Chemical Resistance● All parts are plastic or Teflon®. No elastomers

or metal parts are used.

Lubrication Free● No silicone or other lubricants are used

Easy Maintenance● Seal wear is compensated for by hand

tightening the cap (gland). Valve can beserviced in-line. Simply unscrew bonnet toremove complete topworks for inspection ordisassembly.

Heavy Duty Construction● Thick stems

Precise Control

Teflon® Seal – No Elastomers

* PPG = Glass Reinforced Polypropylene.

Bonnet acts asgland nut. Anyseal wear iscompensatedfor by simplehand tightening

Panel Nutfor easymountingto bracketor panel

Globe Body

PVC, CPVC, PPG*

SERIES: NG – Globe bodyNA – Angle body

SIZES: 1/4", 3/8" & 1/2"

ENDS: Female NPT

STEM SEAL: Teflon® PTFE

Angle Body

Y SedimentStrainersThe Chemline YSA Series Y Sediment Strainer is asafety filtration device designed to entrapoccasional solid impurities in the line. This is toprotect equipment with small orifices such assolenoid valves, and prevent damage to pumps orcontrol valves, etc. The easily replaceable filterscreen comes in a choice of meshes. The new YSASeries True Union models have greatly increasedfiltration areas. Pressure drops are lower and lessfrequent cleaning is required.

Features

● Large Filtration CapacityLow Pressure Drops– Diameter of screens are full pipe bore. The

effective filtering area is in some sizes twicethe filtering area of other makes. This resultsin larger filtration capacities and lowerpressure drops.

● Replaceable Filter Screens– Available with choice of PVC 24, 35 or 55

mesh filter screens– 316 SS screens are also available

● Dual Socket and Threaded Ends– Sizes 1/2" to 2" in PVC are supplied with

socket ends plus two free threaded endsin each box

High Capacity

True Union up to 4"

Transparent Body

1 Polypropylene and PVDF Strainers are available special order.2 For ChemFlareTM end connectors, consult Chemline.3 Other seal materials are available special order.

● Easily Maintained – All parts are easilyreplaceable including the body


Transparent Bodypermits easy inspectionof filter screen

True Union DesignBody slips out of line.No need for flanges.

Hand Nut allows easydisassembly

Suitable fordrain valve

● Optional Flush Valve

PVC1

SERIES: YSA

SIZES: 1/2" – 4"

ENDS: True Union, Threaded, Socket,Flanged or ChemFlareTM2

SEALS: EPDM, FKM (Viton®)3

C O N T R O L S + F L O W M E T E R S

ISO 9001:2008 CERTIFIED

Gauge Isolators · Air Release · Control Valves Pressure Regulators · Variable Area Flow Meters

Chemline SG Series Gauge Isolators allow inexpensive pressure gauges, or any other pressure instrument to be used in corrosive services. The upper chamber (gauge side) is filled with a stable fluid such as glycol or glycerine2. A diaphragm separates it from the lower chamber which receives the media under pressure.

The 1/2” gauge connection allows use of the popular 4” and 4-1/2” diameter gauges. Pressure switches or transmitters may also be installed. Customers can easily fill isolators and install their own gauges.

features

Gauge Isolators

1 2 3 4

SERIES:

INLET CONNECTION: 1

INSTRUMENT CONNECTION:

DIAPHRAGM:

PVC PP

Provisionfor Fill Port

Stainless SteelBands Prevent FNPT ports from splitting

Easy to Mount Gauges It is easy to fill an isolator and field mount a gauge. No special equipment is required. Will accept popular 4” and 4-1/2” diameter gauges

Provision for Fill Port Housing may be drilled and tapped by Chemline or customer for a threaded fill port. This is used for filling isolator using a vacuum filling station

High Chemical Resistance Choice of body materials for a wide range of applications

PTFE bonded EPDM dished diaphragm for high chemical resistance and sensitivity

Heavy Duty Design for Safety PPG3 top chamber Heavy wall connection ports

CRN Registration number by province Ontario: OH16085.5

Optional Gauges Isolators are available alone or with gauge mounted and prefilled with glycol2

A

B

C

D

A With 2” gauge B With 4-1/2” gauge C With 2” back mount gauge D With pressure transmitter

4

The Chemline AA Series Air and Vacuum Release Valve provides a controlled venting solution for larger diameter piping systems. This valve reduces the potential for water hammer incidents that occur when pressure builds up due to entrapped air. A unique two-stage ball stop prevents liquids from escaping while allowing high volume air release while the pipeline is under pressure, also at low pressure when it is being filled.

The vacuum release function allows air to re-enter the pipeline to prevent vacuum collapse.

PDCPD (Polydicyclopenthadiene) is a polyolefin thermoset plastic. Valve parts are manufactured by a process called reaction injection moulding (RIM). PDCPD has excellent corrosion resistance and temperature ratings, very similar to those of polypropylene. It is durable material offering very high impact strength and a fraction of the weight of cast iron.

features

Air & Vacuum Release Valves

SERIES:

SIZES:

ENDS²:

SEALS:

PDCPD

1

High Impact Strength

Superior Exhaust Performance High discharge capacities Two-stage (high/low) exhaust function

Works at Low Pressures Half the minimum pressure compared to cast iron

Excellent Corrosion Resistance PDCPD (polydicyclopenthadiene) material has chemical resistance similar to polypropylene

Top Entry Easy access to internal parts while valve is in line

Removeable Cover

1 2

The Chemline AR Series Air Release Valve allow gases to escape from unpressurized pipe lines. It must be installed vertically at the highest point in the piping system with the “Air” arrow up. As the unpressurized air vents, liquid rises to the float (an inverted cup), which lifts the float up against the seat, holding liquid pressure. The float will not release until the pressure on the inlet side of the valve is equal to the outlet pressure of the valve (normally atmospheric).

features

AR Series Air Release Valves

SERIES:

SIZES:

ENDS:

SEALS: ®)

PVCFull Size Range 1/2” to 3”

Large Flow Capacities Valves have full port liquid capacities, so for air flow they may be chosen several sizes smaller than the liquid pipeline.

Outlet Cap Available For non-hazardous fluids, the optional removeable PE outlet cap prevents tampering with the union nut. Eliminates possible splashing during quick closure and covers the open end.

For hazardous fluids, a 3 foot pipe should be installed on the outlet side or the outlet should be piped to a containment area.

With Outlet Cap

Chemline HC Series is a true large port 6” ball valve manufactured in PVC, polypropylene and PVDF. Most other 6” valves often are 4” with ends increased to 6”. HC Series offers an unobstructed full port which allows passage of mechanical pipe cleaners or “pigs”. Applications include unfiltered sea water and sewage lines. It is also suitable for mild slurries and vacuum lines.

SB17 Mini BackPressure/Relief Valves

SERIES:

SIZES:

ENDS: 1

DIAPHRAGM:

O-RINGS: ®)

PVC PP PVDF

features

Spring Tensioning Bolt

1

True Union Ends Easy installation and maintenance Eliminate chemical leakage problems common with old fashioned threaded connections

Flow Rates Up to 500 l/hr

Recommended Viscosity Recommended for services with a maximum viscosity of 400cP

CRN Registration numbers by province Ontario: OC10134.5 Newfoundland: OC10134.50 Alberta: OC10134.52 Saskatchewan/Manitoba/Quebec: OC10134.56 New Brunswick: OC10134.57 Nova Scotia: OC10134.58 P.E.I.: OC10134.59 British Columbia: not required

Set Pressure Range 7.5 to 150 psi

Flow Rates Up to 500 l/hr (2.2 USGPM)

Maximum Viscosity: 400cP is maximum recommended service viscosity

technical

Optional ChemFlareTM End Connections

SERIES:

SIZES:

ENDS: 1

2

DIAPHRAGM:

SEALS: ®)

The Chemline SB Series Back Pressure/Relief Valve has two functions. As a back pressure valve, installed in-line downstream of a pump, the back pressure below the metering pump is maintained. When installed in the branch of a tee it is a pressure relief valve. The valve stays closed until inlet pressure reaches the set pressure which is adjusted by turning the spring tensioning bolt. Inlet pressure acts on the PTFE control diaphragm opening the valve, allowing excess pressure to flow downwards through the orifice.

The SB10/11 Series is very sensitive to pressure changes and requires low overpressure to fully open. It is designed for clean fluids only.

PVC PP features

SB10/11 SeriesBack Pressure/Relief Valves


Long Cycling Life Dynamic seal is PTFE bonded EPDM for high chemical resistance This moulded diaphragm is designed for superior sealing and flex life

Designed for Superior Performance Valves are hydraulically designed for low hysteresis (“backlash”) and to eliminate chatter Low overpressure to fully open Sensitive to pressure changes


True Union EndsEasy installation and maintenance

technicalSet Pressure Ranges SB10 – 3 to 60 psi SB11 – 7 to 150 psi

– The only difference between SB10 and SB11 is the strength of spring

Maximum Viscosity 120cP is maximum recommended service viscosity

1 2

SERIES:

SIZES:

ENDS: 1

2

DIAPHRAGM:

SEALS: ®)

The Chemline SB Series Back Pressure/Relief Valve has two functions. As a back pressure valve, installed in-line downstream of a pump, the back pressure below the metering pump is maintained. When installed in the branch of a tee it is a pressure relief valve. The valve stays closed until inlet pressure reaches the set pressure which is adjusted by turning the spring tensioning bolt. Inlet pressure acts upward against the piston allowing excess pressure to flow upwards through the orifice.

The SB12 Series has a built-in check valve function, desirable for dosing applications. It is not so sensitive as to open with every pulsation from a metering pump.

PVC PP features

SB12 SeriesBack Pressure/Relief Valves



Superior Performance in Dosing Systems Valves are hydraulically designed for very low hysteresis (“backlash”) and to eliminate chatter Built-in check (non-return) function Valve opening depends on inlet pressure only and is uneffected by changes in downstream (back) pressure




technicalSet Pressure Ranges 1/2” to 2” – 5 to 150 psi 2-1/2” and 3” – 7.5 to 150 psi 2-1/2” to 4” – 4 to 60 psi (optional) 4” – 7.5 to 90 psi


1 2

SERIES:

SIZES:

ENDS: 1

2

DIAPHRAGM:

SEALS: ®)

The Chemline SR 50 Series Pressure Regulating (Reducing) valves maintains a set downstream pressure independent of higher variable upstream pressures. As downstream pressure increases reaching the set pressure, the valve closes. It opens as soon as the downstream pressure decreases below set pressure.

The SR 50 is sensitive and provides precise control. One application is to protect filters from damaging pressure surges.

PVC PP

features

SR50 SeriesPressure Regulating (Reducing) Valves



Designed for Superior Performance Designed for minimum hysteresis Seat is hydraulically designed to eliminate chatter




technicalDownstream Set Pressure Ranges 1/2” to 2” – 15 to 130 psi 2-1/2” and 3” – 15 to 90 psi


1 2 3

3

SERIES:

SIZES:

TYPE:

ENDS:

SHAFT SEAL:

BODY SEAL: ®

The Chemline E Series Exner Characterized Control Valves provide extremely precise flow control of aggressive fluids. Valves flow characteristics (Cv vs. lift) follow theoretical linear or equal percentage curves through the entire range of stem travel. This is accomplished with precision made replaceable seats and plugs in a wide variety of Cv values.

The PTFE bellows shaft seal provides almost frictionless stem movement and provides over 10 years of maintenance-free operation on aggressive chemical services1.

PVC PPfeaturesPrecise and Sensitive Control Predictable and repeatable control of corrosive fluids. These valves respond smoothly and quickly to small changes in signal. Deadband and hysteresis is negligible.

High Rangeability Valve characteristics (flow rate vs. stem lift) follows the theoretical curves through the entire range of opening including extreme ends of travel

Class IV Leakage Rate is 0.01% of rated capacity according to ANSI B16.104-1976

Large Choice of Cv Values 18 standard Cv’s from 0.11 to 105.00 Smaller Cv’s down to 0.003 are available

Field Interchangeable Seats and Plugs Valve Cv may be changed later if flow conditions change

Special materials are available

Abrasion Resistant Have outperformed metal valves on aggressive and crystallizing services

Fibreglass Reinforced Polyester Actuator for external corrosion resistance and light weight

Visual Position Indicator

EK Series with PVDF body and optional positioner EE Series Electrically Actuated

1

Monobloc Thermoplastic Body Resists aggressive chemicals inside and out.Strong enough for metal piping systems.

Exner CharacterizedControl Valves

SERIES: 1

MATERIALS: 2

3

O-RINGS: ®)

CAPACITIES:

Chemline F Series Variable Area Flow Meters are ideal for plastic piping. They provide a combination of accurate visual flow rate measurement and clear flow indication from a distance. Optional limit switches allow the units to signal a low or high flow alarm. An optional flow transmitter provides a 4 to 20 mA signal output. These flow meters must be installed vertically with flow upward.

PVC CPVC PP

features

Variable AreaFlow Meters

Clear Visual Indication Large orange float is visible from a distance Range indicators slide along dovetail track

Easy Installation and Maintenance Just unscrew union nuts and tube slides out of line

Choice of Four Tube Materials for Many Applications: Clear PVC – For Water or Chemicals up to 60ºC (140ºF) – High Chemical resistance at low cost

Polyamide (PA) – For Water or Air up to 75ºC (167ºF) – High impact strength and optical clarity

Polysulfone (PSU) – For Chemicals and Gases up to 100ºC (212ºF) – High impact strength and good chemical resistance

PVDF2 – For Chemicals and Ultrapure fluids up to 110ºC (230ºF) – High impact strength and excellent chemical resistance.

Ideal for All Types of Plastic Piping All types of end connections in PVC, CPVC, PP & PVDF

Low Pressure Drop

Good Measuring Accuracy – Class IV ± 3% of indicated value, plus ± 1% of full scale. – Read scale at top (largest diameter) of float

Non Fouling Float is self supporting in the flow. No guide rod (which can cause the float to jam) is necessary.

CRN Registration numbers by province Ontario: OF10134.5 Newfoundland: OF10134.50 Alberta: OF10134.52 Saskatchewan/Manitoba/Quebec: OF10134.56 New Brunswick: OF10134.57 Nova Scotia: OF10134.58 P.E.I.: OF10134.59 British Columbia: not required

StandardFull Size

Compact

1

2 3

PVC

Variable Area Flow Meters

PVCTube

FCA00020

FCA00060

FCA00100

FCA00250

FCA00051

FCA00151

FCA00251

FCA00401

FCA00152

FCA00402

FCA00602

FCA01002

FCA00253

FCA00403

FCA01003

FCA01503

PolyamideTube

FCT00020

FCT00060

FCT00100

FCT00250

FCT00051

FCT00151

FCT00251

FCT00401

FCT00152

FCT00402

FCT00602

FCT01002

FCT00253

FCT00403

FCT01003

FCT01503

PolysulfoneTube

FCP00020

FCP00060

FCP00100

FCP00250

FCP00051

FCP00151

FCP00251

FCP00401

FCP00152

FCP00402

FCP00602

FCP01002

FCP00253

FCP00403

FCP01003

FCP01503

USGPM

0.0132 – 0.106

0.022 – 0.264

0.04 – 0.44

0.11 – 1.10

0.02 – 0.22

0.07 – 0.66

0.11 – 1.10

0.18 – 1.76

0.07 – 0.66

0.22 – 1.76

0.26 – 2.64

0.44 – 4.40

0.11 – 1.10

0.18 – 1.76

0.44 – 4.40

0.66 – 6.60

Litres per hour

3 – 24

5 – 60

10 – 100

25 – 250

5 – 50

15 – 150

25 – 250

40 – 400

15 – 150

40 – 400

60 – 600

100 – 1,000

25 – 250

40 – 400

100 – 1,000

150 – 1,500

A

6.50

6.50

6.50

6.50

6.69

6.69

6.69

6.69

7.28

7.28

7.28

7.28

7.87

7.87

7.87

7.87

D

1.38

1.38

1.38

1.38

1.69

1.69

1.69

1.69

2.09

2.09

2.09

2.09

2.36

2.36

2.36

2.36

Water

0.05

0.05

0.05

0.05

0.04

0.04

0.04

0.04

0.09

0.09

0.09

0.09

0.09

0.09

0.09

0.09

Air

0.07

0.07

0.07

0.07

0.06

0.06

0.06

0.06

0.12

0.12

0.12

0.12

0.12

0.12

0.12

0.12

EndConn.Size

3/8”

1/2”

3/4”

1”

Item Number Flow Range (water) Dimensions (inches)

FC SERIES – COMPACT SIZE – 5” SCALE

NOTES:PVDF flow meters are available in all sizes. Change third letter in item number to K.1 �P = Pressure loss through flow meter with water at 20ºC (68ºF).

2 Dimension L is for PVC Socket ends.

Single USGPM (water) scale is supplied standard

FS SERIES – STANDARD FULL SIZE – 7” SCALE

CONVERSION CHART – FLOW UNITS

Values based on water at 20ºC (68ºF).

PVCTube

FSA00600

FSA01000

FSA01500

FSA02500

FSA02000

FSA03000

FSA04000

FSA06000

FSA10000

FSA15000

FSA25000

FSA50000

PolyamideTube

FST00600

FST01000

FST01500

FST02500

FST02000

FST03000

FST04000

FST06000

FST10000

FST15000

FST25000

FST50000

PolysulfoneTube

FSP00600

FSP01000

FSP01500

FSP02500

FSP02000

FSP03000

FSP04000

FSP06000

FSP10000

FSP15000

FSP25000

FSP50000

USGPM

0.26 – 2.64

0.44 – 4.40

0.66 – 6.60

1.10 – 11.00

0.88 – 8.80

1.32 – 13.20

1.76 – 17.60

2.64 – 26.40

4.40 – 44.00

6.60 – 66.00

11.00 – 110.00

44.00 – 220.00

Litres per hour

60 – 600

100 – 1,000

150 – 1,500

250 – 2,500

200 – 2,000

300 – 3,000

400 – 4,000

600 – 6,000

1,000 – 10,000

1,500 – 15,000

2,500 – 25,000

10,000 – 50,000

A

13.78

13.78

13.78

13.78

13.78

13.78

13.78

13.78

13.78

13.78

13.78

13.78

L2

16.3

16.3

16.6

16.6

16.8

16.8

17.2

17.2

17.2

17.7

17.7

17.7

D

2.36

2.36

2.83

2.83

3.27

3.27

4.06

4.06

4.06

4.80

4.80

4.80

Water

0.18

0.18

0.18

0.18

0.18

0.18

0.32

0.32

0.32

0.49

0.49

0.49

Air

0.23

0.23

0.23

0.23

0.23

0.23

0.39

0.39

0.39

0.58

0.58

0.58

EndConn.Size

1”

1-1/4”

1-1/2”

2”

2-1/2”

PressureDrop (psi)1

Item Number Flow Range (water) Dimensions (inches)

Dual USGPM (water) and litres per hour scales are supplied standard

From To

m3/hr

litres/hr

USGPM

ImpGPM

ft3/min

m3/hr

1

0.001

0.2271

0.2728

1.6990

litres/hr

1000

1

227.12

272.77

1699

USGPM

4.4029

.004403

1

1.2009

7.4806

ImpGPM

3.6662

.003666

0.8327

1

6.2289

ft3/min

0.5886

.000589

0.1337

0.1605

1

PressureDrop (psi)1

L2

8.2

8.2

8.2

8.2

8.7

8.7

8.7

8.7

9.6

9.6

9.6

9.6

10.5

10.5

10.5

10.5

Variable Area Flow Meters

SCALE CORRECTION FACTORS – FOR AIR AT NON-STANDARD TEMPERATURES AND PRESSURES

Flow MeterItem No.

Normalm3/hr

StandardCFM

Method 1

Calculate the Factor with the following formula.

Factor = 1 psia 3.7005 (1+0.00367t)

psia = pressure of the air absolute = psig + 14.7 (atmospheric pressure = 14.7 psia)t = temperature of the air ºC

Air density is dependent on the actual pressure and temperature. Calculate the Scale Correction Factor using either Method 1 or 2. Multiply the standard air flow ranges above by the Factor to obtain actual flow rates.

Method 2

Calculate the density of the air at conditions and find factor from the chart below.

Air Density (g/ml) = psia 11,360 (1+0.00367t)psia = pressure of the air absolute = psig + 14.7 (atmospheric pressure = 14.7 psia)t = temperature of the air ºC

FLOW RANGES FOR AIR – AT STANDARD CONDITIONS (atmospheric pressure 14.7 psia/20OC).

Flow Meter Item No.

Normalm3/hr

StandardCFM

FCT00020FCT00060FCT00100FCT00250FCT00051FCT00151FCT00251FCT00401FCT00152FCT00402FCT00602FCT01002FCT00253FCT00403FCT01003FCT01503

0.2 – 1.0 0.2 – 2.5 0.6 – 3.6 0.5 – 9.0 0.4 – 2.8 0.8 – 6.2 0.9 – 9.5 2.0 – 15.0 0.5 – 5.5 2.0 – 14.0 2.5 – 22.0 4.0 – 34.0 1.0 – 8.0 2.0 – 14.0 4.0 – 34.0 5.0 – 50.0

0.1 – 0.6 0.1 – 1.5 0.4 – 2.1 0.3 – 5.3 0.2 – 1.6 0.5 – 3.6 0.5 – 5.6 1.2 – 8.8 0.3 – 3.2 1.2 – 8.2 1.5 – 12.9 2.4 – 20.0 0.6 – 4.7 1.2 – 8.2 2.4 – 20.0 2.9 – 29.4

1.5 – 12 2.4 – 20 2.9 – 29 5.0 – 45 4.7 – 41 5.9 – 53 8.2 – 74 13 – 112 21 – 177 29 – 294 47 – 424 234 – 883

2.5 – 20 4 – 34 5 – 50 8.5 – 76 8 – 70 10 – 90 14 – 125 22 – 190 35 – 300 50 – 500 80 – 720 400 – 1,500

FST00600FST01000FST01500FST02000FST02500FST03000FST04000FST06000FST10000FST15000FST25000FST50000

FC SERIES – COMPACT SIZE – 5” SCALE FS SERIES – STANDARD FULL SIZE – 7” SCALE

Air Density (g/ml) Temperature in oC

Temperature vs. Pressure

00.0

020.0

030.0

050.0

070.0

090.0

110.0

13

0.004

0.006

0.008

0.010

0.012

0.014 0 0

-10 10 30 50 70 90 11

020 40 60 80 100

120

130

0.50

1.00

1.50

2.00

2.50

3.00

3.50

1

2

3

4

5

6

7

8

9

10

Scal

e C

orre

ctio

n Fa

ctor

Pres

sure

in B

ar

Air Density vs. Flow Factor

0.001

A C T U A T I O N + A C T U A T E D V A LV E S

actu

atio

n +

actu

ated

val

ves

ISO 9001:2008 CERTIFIED

Electric Actuators · Pneumatic Actuators 700 Series Actuated + Manual Diaphragm Valves

The Chemline Electromni® Actuator is a high quality yet economical electric actuator for mounting onto all Chemline Compact, Type 21 True Union and Type 23 Multi Port ball valves up to 2”. The actuator is compact and light weight – well suited for plastic and also metal ball valves.

Chemline normally mounts Electromni’s to ball valves in-house. The units are assembled, adjusted and bench tested prior to shipment.

Electromni®

Electric Actuators

SERIES: EO – Standard EL – With Lights

VOLTAGES: 12, 24, 115 or 220 VAC, 12 or 24 VDC

ENCLOSURE: High Impact ABS Plastic Cover & PVC Base NEMA 4X

featuresMultiple Operation/Control Options 3-wire (standard) 2-wire (optional)

Multiple Feedback Options Visual (integrated lights – optional) Feedback Switch (optional)

Approved by CSA¹

(Canadian Standards Association)

NEMA 4X Enclosure Waterproof, corrosion proof with high impact ABS cover, PVC base and stainless steel fasteners

No Maintenance Permanently lubricated gear train Designed for 250,000 + cycles

Thermal Overload Protection Thermal switch embedded into motor windings

Extended Operating Temperature Range –10 to 60oC (15 to 140oF)

Standard Mounting Dimensions ISO-5211 mounting bolt circle

Electromni® on Chemline Compact Ball Valve

Operating Voltage 115 VAC (standard) 220 VAC, 12 or 24 VAC or VDC (optional)

Electrical Conduit Entry 1 x 1/2” NPT

Motor Direction Unidirectional (115/220 VAC) Reversing (12/24 VAC/VDC)

Motor Cycle Time Fixed (standard)

technical

for Chemline ball valves up to 2”

¹Special inspection labelled.

The Chemline Q Series Electric Actuator is a reversible rotary unit with output torques of 150 or 300 in.-lb. These units are ideal for all Chemline ball valves up to 3” size, as well as butterfly valves up to 3”. The Q Series is compact, light weight and has a plastic housing. A large red handle provides manual override and position indication.

Chemline also offers complete actuated ball, butterfly and diaphragm valves, assembled and bench tested. Actuation service is also available for all quarter-turn metal valves.

Q SeriesElectric Actuators

SERIES: QA – 150 in.lb. QB – 300 in.lb.


ENCLOSURE: High Impact “Zytel” Plastic Cover NEMA 4X

features

technical

valves up to 3”

Multiple Operation/Control Options 3-wire (standard) Adjustable Travel (standard) Manual Override (standard) 2-wire (optional) 3-position (optional) Cycle Length Control (optional) Digital Positioner (optional) Failsafe (optional) Heater/Thermostat (optional) Mechanical Brake (optional)

Multiple Feedback Options Visual (standard) Feedback Switches (optional) Feedback Potentiometer (optional) Feedback Transmitter (optional)

Approved by CSA¹(Canadian Standards Association)

NEMA 4X Enclosure Waterproof, corrosion proof with high impact Zytel2 housing and stainless steel fasteners



Extended Operating Temperature Range –10 to 60oC (15 to 140oF) (standard) Lower temperature reachable with anti-condensation cold weather heater/thermostat (optional)

Standard Mounting Dimensions ISO-5211 mounting bolt circle and drive



Motor Direction Reversing

Motor Cycle Time Fixed (standard) Adjustable (optional)1 Special inspection labelled.

2 Zytel FR-50 is a flame retardant 25% glass reinforced high strength polyamide (Nylon) resin from DuPont.

Declutchable Manual Override/ Position Indicator

Q Series on Type 57 Butterfly Valve

Q Series on Type 21 True Union Ball Valve

The Chemline V Series Electric Actuator is a reversible rotary unit with output torques up to 8,860 in.-lb. These actuators are ideal for Chemline butterfly valves up to 20”1 size, as well as all sizes of Chemline ball valves up to 6”. The V Series actuator features a moulded Polyamide 6.6 cover, a die cast aluminum base with a thermally bonded epoxy powder coating, rated as a NEMA 4X enclosure. NEMA 7 and 9 enclosures are available. Consult Chemline.


V SeriesElectric Actuators

SERIES: VR – 220 to 660 in.lb. VS – 880 to 2,660 in.lb. VT – 5,300 to 8,860 in.lb.

VOLTAGES: 115/220 VAC (50/60Hz), 12/24 VDC, 24 VAC (50/60Hz)

ENCLOSURE: Polyamide 6.6 Cover & Epoxy Coated Aluminum Base NEMA 4X

features

technical


VS Series on Type 21 Ball Valve

VS Series on Type 57 Butterfly Valve

MechanicalTravel Stops

PositionIndicatorBeacon

Multiple Operation/Control Options 2 & 3-wire (standard) Adjustable Travel (standard) Adjustable Travel Stops (standard)2

Anti-Condensation Heater/Thermostat (standard) Manual Override (standard) Bus Communication (optional) Digital Positioner (optional) Failsafe (optional) Cold weather Heater/Thermostat (optional)

Multiple Feedback Options Visual (standard) Feedback Switches (standard) Extra Feedback Switches (optional) Feedback Potentiometer (optional) Feedback Transmitter (optional)

Approved by CSA3 (Canadian Standards Association)

NEMA 4X/IP67 Enclosure4

Waterproof, corrosion proof with high impact Polyamide 6.6 cover, thermally bonded epoxy powder coated die cast aluminum base and stainless steel fasteners


Thermal Overload Protection Thermal switch embedded onto control board

Extended Operating Temperature Range –10 to 60oC (15 to 140oF) (standard) Lower temperature reachable with cold weather heater/thermostat (optional)


Operating Voltage 115/220 VAC 50/60 Hz (standard) 12/24 VDC or 12 VAC 50/60 Hz (optional)




1 Contact Chemline for specific line pressure ratings2 VS and VT only3 Special inspection labelled4 IP67 (submersible to 2 metres up to 72 hours) with polyamide cover. Rated to IP68 with metal cover.

The Chemline A Series Electric Actuator is a reversible rotary unit with output torques up to 2000 in.-lb. These actuators power Chemline butterfly valves up to 6” size, as well as all sizes of Chemline ball valves up to 6”. The A Series actuator features an epoxy coated die cast aluminum housing with NEMA 4X enclosure rating. Chemline also offers complete actuated ball, butterfly and diaphragm valves, assembled and bench tested. Actuation service is also available for all quarter-turn metal valves.

A SeriesElectric Actuators

SERIES: AA – 400 in.lb. AB – 700 in.lb. AC – 1,100 in.lb. AD – 2,000 in.lb.


ENCLOSURE: Baked Hybrid Epoxy Coated Die Cast Aluminum NEMA 4X

features

technical

valves up to 6”




Motor Cycle Time Fixed (standard) Adjustable (optional)

Multiple Operation/Control Options 3-wire (standard) Adjustable Travel (standard) Manual Override (standard) 2-wire (optional) 3-position (optional) AS-i Bus communication (optional) Cycle Length Control (optional) Digital Positioner (optional) Failsafe (optional) Heater/Thermostat3

Mechanical Brake (optional) Multiple-Turn (optional)

Multiple Feedback Options Visual (standard) Feedback Switches (optional) Feedback Potentiometer (optional) Feedback Transmitter (optional)

Approved by CSA¹ (Canadian Standards Association)

NEMA 4X Enclosure Waterproof, corrosion proof with baked hybrid epoxy coated die cast aluminum housing and stainless steel fasteners



Extended Operating Temperature Range –10 to 60oC (15 to 140oF) (standard) Lower temperature reachable with anti-condensation/cold weather heater/thermostat (optional)


A Series on Type 21 Ball Valve

Beacon Visual Position Indicator and Declutchable Manual Override2

1 Special inspection labelled 2 “D” size actuator has declutching hand wheel override3 Optional on AA and AB models, standard on AC and AD models

A Series on Type 57 Butterfly Valve

The Chemline E Series Electric Actuator is a reversible rotary unit with output torques up to 880 in.-lb. These units are ideal for all Chemline ball and butterfly valves up to 4”. The E Series is compact, light weight and has a plastic housing. A large black handle provides manual override and position indicator.


E SeriesElectric Actuators

SERIES: ER10 – 90 in.lb. ER20 – 180 in.lb. ER35 – 310 in.lb. ER60 – 530 in.lb. ER100 – 880 in.lb.

VOLTAGES: 115/220 VAC, 12/24 VDC, 24 VAC

ENCLOSURE: Polyamide 6.6 NEMA 4X

features

technical

valves up to 4”

Operating Voltage 115/220 VAC (standard) 12/24 VDC or 12 VAC (optional)




1 Special inspection labelled.

Multiple Operation/Control Options 2 & 3-wire (standard) Adjustable Travel (standard) Anti-Condensation Heater/Thermostat (standard) Manual Override (standard) Bus communication (optional) Digital Positioner (optional) Failsafe (optional) Cold weather Heater/Thermostat (optional)

Multiple Feedback Options Visual (standard) Feedback Switches (standard) Extra Feedback Switches (optional) Feedback Potentiometer (optional) Feedback Transmitter (optional)

Approved by CSA¹(Canadian Standards Association)

NEMA 4X Enclosure Waterproof, corrosion proof with high impact Polyamide 6.6 housing and stainless steel fasteners


Thermal Overload Protection Thermal switch embedded onto control board

Extended Operating Temperature Range –10 to 60oC (15 to 140oF) (standard) Lower temperature reachable with cold weather heater/thermostat (optional)


E Series on SM Series True Union Ball Valve

Declutchable Manual Override/ Position Indicator

Chemline PA Series is part of the P Series family of quarter-turn pneumatic rack and pinion actuators designed for long cycling life in demanding industrial applications.

PA Series features aluminum bodies and end caps coated inside and out with a two part coating of cataphoresis epoxy then Rilsan polyamide. The result is a superior actuator with longer cycling life and durable abrasion and corrosion resistant surfaces.

Output torques are up to 15,660 in.-lbs. spring return1 (SR) and 40,660 in-lbs. double acting (DA) with 80 psi control air. They will power all Chemline ball valves and butterfly valves up to 24” DA and 20” SR.

Chemline offers complete actuated ball and butterfly valves assembled and bench tested. Actuation services are also available for all quarter-turn metal valves.

PA SeriesPneumatic Actuators

MATERIAL: Epoxy and Rilsan® coated aluminum

SERIES: PAS – Spring Return PAD – Double Acting

CONTROL PRESSURE: 40 to 120 psi

OUTPUT TORQUES: Spring Return : up to 15,660 in.-lb.(AT 80 PSI AIR) Double Acting: up to 40,660 in.-lb.

features


1 Based on Spring End torque, used for sizing on normally closed butterfly valves. 2 See page 19 for details of coating process.

Application Diversity Industrial Process Submersion Bleach or water washdown

Quality Built for Long Cycling Life Rated for over 1 million cycles Self-lubricating Rilsan® coating on inner cylinder surfaces for better wear than epoxy or anodizing Molybdenum grease-impregnated O-rings PTFE impregnated piston wear pads and wear rings Double O-ring shaft seals Minimum backlash with no play between parts Massive tooth engagement between racks and pinion

Corrosion Resistant Silicone-free aluminum alloy body and end caps 4-step pre-treatment process Cataphoresis layer for extra protection Self-lubricating Rilsan® coating2 offers outstanding chemical and abrasion resistance

Standard Mounting Dimensions ISO 5211 bottom bolt circles and drives allow direct mounting to most valves NAMUR solenoid pad and VDI/VDE 3845 top shaft allow for mounting of all standardized accessories Standardized actuator mounting kits are available for many valve makes

Compact, Simple Design Dual-opposed rack and pinion design supplies high torque for its size and weight Air porting is integral, keeps design clean and simple

Integrated Travel Stops Permit adjustment of last 5 degrees of either open or closed position travel

Safety Spring Set Prevent dangerous release of spring tension during disassembly

PA Series on Type 21 True Union Ball Valve

Chemline PP Series is part of the P Series family of quarter-turn pneumatic rack and pinion actuators designed for long cycling life in demanding industrial applications.

PP Series actuators feature bodies and end caps of injection moulded polyamide, 50% glass filled. These light weight compact actuators offer good chemical resistance. Chemline valves with PP actuators make an “all-plastic” lighter package, attractive for plastic piping systems.

Output torques are up to 915 in.-lbs. spring return (SR) and 1,335 in.-lbs. double acting (DA) with 80 psi control air. They will power all Chemline ball valves and butterfly valves up to 6” DA and 4” SR.

Chemline offers actuated ball and butterfly valves, assembled and bench tested. A complete range of control accessories is available. Also offered is actuation service for all quarter-turn metal valves.

PP SeriesPneumatic Actuators

MATERIAL: Polyamide

SERIES: PPS – Spring Return PPD – Double Acting


OUTPUT TORQUES: Spring Return : up to 915 in.-lb.(AT 80 PSI AIR) Double Acting: up to 1,335 in.-lb.

features


Application Diversity Industrial process Light weight or all-plastic applications

Quality Built for Long Cycling Life Rated for over 1 million cycles Molybdenum grease-impregnated O-rings PTFE impregnated piston wear pads and wear rings Double O-ring shaft seals Minimum backlash with no play between parts Massive tooth engagement between racks and pinion

Corrosion Resistant Injection moulded 50% glass-filled Polyamide body and end caps




1 50% Glass Reinforced Polyamide, also know as “Nylon 66”. 2 Based on Spring End torque, used for sizing on normally closed butterfly valves.

PP Series on Type 21 True Union Ball Valve

Chemline P3 Series are quarter turn pneumatic actuators specially chosen for all sizes of ball and butterfly valves. These actuators are designed to withstand highly corrosive environments, underwater and marine applications. All offer long cycling life.

Normal working temperatures are –32oC to 90oC. They may be actuated with air or non-aggressive fluids up to 120 psi pressure.

P3 Series is one in a range of actuators specially selected for ball and butterfly valves. Hardware kits are available for mounting of actuators in the field. Also offers complete actuated valves, fully assembled and bench tested.

P3 SeriesPneumatic Actuators

MATERIAL: 316 Stainless Steel

SERIES: P3SR – Spring Return P3DA – Double Acting


OUTPUT TORQUES: Spring Return: up to 2,422 in.-lb.(AT 80 PSI AIR) Double Acting: up to 5,757 in.-lb.

featuresfor Chemline ball valves up to 6”

Application Diversity Industrial process Submersion Off-shore service

Quality Built for Long Cycling Life Rated for over 1 million cycles Molybdenum grease-impregnated O-rings PTFE impregnated piston wear pads and wear rings Double O-ring shaft seals Minimum backlash with no play between parts Massive tooth engagement between racks and pinion

Corrosion Resistant 316 Stainless Steel





Integrated Travel Stops

Standard NAMUR Pad for flush mounting of solenoid valve

Standardized ISO Bolt Pattern for mounting to valve

RetainedConcentric Nested Spring Sets

Position Indicator

Standard NAMUR dimension Shaft and Bolt Pattern for mounting limit switch box or positioner

Chemline PG Series are half turn pneumatic actuators specially chosen for all sizes of 3-way ball valves. These actuators are epoxy and Rilsan coated for high corrosion resistance. All offer long cycling life.

Normal working temperatures are –32oC to 90oC. They may be actuated with air, water, natural gas or non-aggressive fluids up to 120 psi pressure.

PG Series is one in a range of actuators specially selected for ball and butterfly valves. Hardware kits are available for mounting of actuators in the field. Chemline also offers complete actuated valves, fully assembled and bench tested.

PG Series

Pneumatic Actuators

featuresMATERIAL: Epoxy and Rilsan® coated aluminum

SERIES: PGS – Spring Return PGD – Double Acting


OUTPUT TORQUES: Spring Return : up to 1,200 in.-lb.(AT 80 PSI AIR) Double Acting: up to 2,800 in.-lb.

1 See page 40 for details of coating process.

Application Diversity Industrial Process Submersion Bleach or water washdown

Quality Built for Long Cycling Life Rated for over 1 million cycles Self-lubricating Rilsan® coating on inner cylinder surfaces for better wear than epoxy or anodizing Molybdenum grease-impregnated O-rings PTFE impregnated piston wear pads and wear rings Double O-ring shaft seals Minimum backlash with no play between parts Massive tooth engagement between racks and pinion

Corrosion Resistant Silicone-free aluminum alloy body and end caps 4-step pre-treatment process Cataphoresis layer for extra protection Self-lubricating Rilsan® coating1 offers outstanding chemical and abrasion resistance





PG Series on Type 23 True Union Ball Valve

The Chemline Type 730 Pneumatically Actuated Diaphragm Valve features a plastic diaphragm actuator, either normally closed, normally open or double acting. This valve offers long cycling life, high pressure resistance and a size range 1/2” to 4”. Being a diaphragm valve, it is available for sanitary or slurry applications. With a PTFE diaphragm, it has corrosion resistance superior to ball or butterfly valves. This becomes an economical control valve when a positioner is added.

The Type 730 is part of the 700 Series of diaphragm valves. They feature interchangeable bodies, diaphragms and actuators. Modular construction minimizes spare parts requirements. All major parts are solid plastic – corrosion resistant and light weight to minimize stress on plastic piping.

Diaphragm Valves

featuresSERIES: Type 730

SIZES: 1/2” – 4”

ENDS: True Union Socket, Threaded or ChemFlareTM1

Spigot2 bodies with Plain, Socket, Threaded or Flanged ends

DIAPHRAGMS: EPDM3, FKM-B (Viton®) or PTFE

CONTROL FUNCTIONS: Normally Closed, Normally Open or Double Acting

PVC CPVC PP PVDF

1 For ChemFlareTM end connectors, consult Chemline.2 PP and PVDF spigot ends have metric dimensions and will butt fuse directly to Chemline PP and PVDF piping systems.3 Epoxy cured EPDM

Pressure rated to 150 psi Highest pressure ratings of 700 Series diaphragm valves

Solid Plastic Body and Actuator Light weight Corrosion resistant inside and out

Excellent for Sanitary Applications Self draining PVDF and unpigmented PP bodies are FDA approved for food applications Sanitary clamp end connections are available

Excellent Flow Control With a positioner, this is an inexpensive control valve Diaphragm type actuator provides smooth, sensitive operation

Modular Construction Only 5 actuator and diaphragm sizes for 9 valve sizes. Spare parts requirements are minimized.

Long Cycling Life Valve is designed for extremely long cycling life

Actuator is essentially maintenance free

Normally closed version shown with True Union body and position indicator

The Chemline Type 750 Pneumatically Actuated Diaphragm Valve features a new design plastic piston actuator, reversible normally closed to normally open. It offers compact dimension, long cycling life and higher leakage resistance, all at a cost lower than 730 Series pneumatically actuated diaphragm valves.

The Type 750 is part of the 700 Series of diaphragm valves. They feature interchangeable bodies, diaphragms and actuators. Modular construction minimizes spare parts requirements. All major parts are solid plastic, corrosion resistant and light weight to minimize stress on plastic piping. Being a diaphragm valve, it is available for sanitary or slurry applications. With a PTFE diaphragm, it has corrosion resistance superior to ball or butterfly valves.

Diaphragm Valves


SIZES: 1/2” – 2”




CONTROL FUNCTIONS: Normally Closed, Normally Open or Double Acting

PVC CPVC PP PVDF

Solid Plastic Body Actuator Light weight Corrosion resistant inside and out

Good Flow Characteristics High Cv values due to smooth and wide body cavity Bidirectional Self draining

Modular Construction Spare parts requirements are minimized because of only 3 actuator and diaphragm sizes for 6 valve sizes Convertible from Normally Closed to Normally Open or Double Acting

New Design for Superior Sealing Risk of leakage is reduced Lower control air pressures are required for full pressure closure

Easy Maintenance Actuator may be easily removed after valve is installed Body is easily removed with True Union ends

Long Life Maintenance Free Actuator Valve is factory tested to 1,000,000 plus cycles Piston seal has double lip ring to retain grease

1 For ChemFlareTM end connectors, consult Chemline.2 PP and PVDF spigot ends have metric dimensions and will butt fuse directly to Chemline PP and PVDF piping systems.3 Epoxy cured EPDM

Normally closed version shown with True Union body and Position Indicator

The Chemline Type 760 Manual Diaphragm Valve is part of the 700 Series of diaphragm valves. 700 Series valves have modular design and interchangeable bodies, diaphragms and actuators. The Type 760 features compact size and all plastic construction for corrosion resistance and light weight. Being a diaphragm valve it is suitable for sanitary or slurry applications. Because it is slow closing, water hammer problems are eliminated. This is also a good throttling valve. With a PTFE diaphragm, it has corrosion resistance superior to ball or butterfly valves.

When a few manual valves are required on a system using the pneumatically actuated 700 Series, the Type 760 is a good choice because the bodies and diaphragms are the same.

Diaphragm Valves


SIZES: 1/2” – 4”




PVC CPVC PP PVDF

manual operation

1 For ChemFlareTM end connectors, consult Chemline.2 PP and PVDF spigot ends have metric dimensions and will butt fuse directly to Chemline PP and PVDF piping systems. PVC spigots are ANSI.3 Epoxy cured EPDM


Excellent for Sanitary Applications Self draining PVDF and unpigmented PP bodies are approved for food applications Sanitary clamp end connections are available

Butt Fusion Ends available Spigot bodies are available 1/2” to 3” for direct butt fusion into Chemline PP and PVDF piping systems. All mechanical connections may be eliminated.

Modular Construction Only 5 actuator and diaphragm sizes for 9 valve sizes. Spare parts requirements are minimized.

No Maintenance Elastomer diaphragms have life well over one million cycles, but if necessary they are easy to replace

Position Indicator

True Union Body

The Chemline Type 710 Pneumatically Actuated Diaphragm Valve features a plastic piston actuator designed for long cycling life and corrosion resistance. Compared to a 1/2” pneumatically actuated ball valve it is a fraction of the size and cost.

Type 710 is part of the 700 Series of diaphragm valves featuring modular construction which minimizes spare parts requirements. Being a diaphragm valve, it is suitable for sanitary or slurry applications. With a PTFE diaphragm, it has corrosion resistance superior to a ball valve.

Diaphragm Valves

features

SERIES: Type 710

SIZES: 3/8”, 1/2”




CONTROL FUNTIONS: Normally Closed Normally Open Double Acting

PVC CPVC PP PVDFPressure rated to 90 psi 90 psi at 20oC for all materials

Long Cycling Life Valves normally operate well over one million cycles maintenance free4

Solid Plastic Body & Actuator High strength “Ixef”5 plastic actuator Lightweight Corrosion Resistant

Epoxy Coated Spring Steel Springs Spring steel springs have longer life and are stronger than stainless steel springs. Epoxy coating resists corrosive environments.

Safety Spring Cartridge Contained spring set allows for safe removal of actuator Spring cartridge may be easily reversed to change between Normally Closed and Normally Open functions

Direct Mount Accessories Accessories (travel stop, position indicator, manual override, limit switch box) thread into the top of the actuator and are easily installed in the field

1 For ChemFlareTM end connectors, consult Chemline.2 PP and PVDF spigot ends have metric dimensions and will butt fuse directly to Chemline PP and PVDF piping systems. PVC spigots are ANSI.3 Epoxy cured EPDM4 With EPDM or FKM-B (Viton®) diaphragm.5 “Ixef” = Polyarilamide

True Union Body

The Chemline Type 720 Manually Operated Diaphragm Valve features compact size a large variety of body materials and end connections. It is much smaller than other 1/2” diaphgram valves.

This is a good throttling valve and is suitable for sanitary or slurry applications. With a PTFE diaphragm, it has corrosion resistance superior to a ball valve.

When a few manual valves are required on a system using the pneumatically actuated Type 710, the Type 720 is a good choice because the bodies and diaphragms are interchangeable.

Diaphragm Valves

features

SERIES: Type 720

SIZES: 3/8”, 1/2”




PVC CPVC PP PVDF

manual operation

1 For ChemFlareTM end connectors, consult Chemline.2 PP and PVDF spigot ends have metric dimensions and will butt fuse directly to Chemline PP and PVDF piping systems. PVC spigots are ANSI.3 Epoxy cured EPDM

Pressure rated to 90 psi 90 psi at 20oC for all materials


Excellent for Sanitary Applications Self draining PVDF and unpigmented PP bodies are approved for food applications Sanitary Tri-clamp end connections are available

Butt Fusion Ends available Spigot bodies are available in 1/2” for direct butt fusion into Chemline PP and PVDF piping systems. All mechanical connections may be eliminated.

Adjustable Travel Stop Prevents excessive pressure on diaphragm, extending life

Sealed Handwheel Protects the stem from corrosive atmosphere

PositionIndicator

True Union Body

chemline · 2019. 11. 14. · multi port ball valves the chemline type 23 multi port ball valve...

Documents