chomp · 2015. 5. 29. · design and diagram by beth johnson recommended paper: 10 inch duo kami...
TRANSCRIPT
CHOMPbeth johnson origami
Hungry FrogDesign and Diagram by Beth JohnsonRecommended paper: 10 inch Duo Kami Difficulty Level: IntermediateDiagrams and models may be reproduced only for personal use, and may not be redistributed or republished in any way without my permission.
1. Fold and unfold. 2. Fold edges to center. 3. Fold in half and unfold.
4. Fold and unfold. 5. Turn model over. 6. Fold and unfold thecorners to the center.
7. Fold and unfold.
8. Fold and unfold. 9. Refold creases made in step 4.
10. Valley fold and unfold angle bisector.
11. Mountain fold creasemade in step 10.
CHOMP
DRAFT
10-11
10-11
13-14
13-14 13-141/3
12 Repeat steps 10-11 on the other three sides.
13. Crimp the model usingexisting creases (can be considered an open sink).Model will not lie flat.
13a. Model opened up to show crease pattern of the collapse.
14.Fold all layers along the crease made in step 6.
15. Repeat steps 13-14on the other three sides.Model will lie flat along midline after all sides are collapsed.
16. Model collapsed, side view. Fold down top 2 layers. Repeatbehind.
17.Spread squash to form eye. Repeatbehind.
18.Gently open up squash fold to round the eye.Repeat behind.
10-11
DRAFT
20. Collapse model in half along existing creases. Thisis similar to collapsing a waterbomb base.
Pull side �aps to make frog CHOMP.
19.Close sink the corner to narrow the body. You can skip this step if you don’t like closed sinks.After sinking, rearrange the layers inside so that onesingle layer lies on top of the other layers to hide the sink. You will have four layers lying to one side of the midline, and one single layer lying to the other side of the midline.See steps 17a and 17b.
19a.19b.
21. Finished!
DRAFT
Hungry SharkDesign and Diagram by Beth JohnsonRecommended paper: 10 inch Duo Kami Difficulty Level: IntermediateDiagrams and models may be reproduced only for personal use, and may not be redistributed or republished in any way without my permission.
1. Fold and unfold. 2. Fold edges to center. 3. Fold in half and unfold.
4. Fold and unfold. 5. Turn model over. 6. Fold and unfold thecorners to the center.
7. Fold and unfold.
8. Fold and unfold. 9. Refold creases made in step 4.
10. Valley fold and unfold angle bisector.
11. Mountain fold creasemade in step 10.
DRAFT
10-11
10-11
13-14
13-14 13-14
12 Repeat steps 10-11 on the other three sides.
13. Crimp the model usingexisting creases (can be considered an open sink).Model will not lie flat.
13a. Model opened up to show crease pattern of the collapse.
14.Inside reverse fold along the creases made in step 6.
15. Repeat steps 13-14 on the other three sides. Model will lie flat along midline after all sides are collapsed.
16. Result. Open up model towork on the layers inside. Model will not lie flat.
17. View from the inside of model.There are four layers of paper at each tip. Fold the top two layers to the halfway point of the side edge.Unfold and repeat on the right side.
1/2
18. Outside reverse fold to color change the shark’s teeth. Repeat on the right side.
1/3
19. Repeat steps 17-18 on the bottom two corners. Butfold the layers over to the1/3 point of the side edge.
10-11
DRAFT
21. Mountain fold and unfold the edges. Repeat behind.
22.Close sink the corner. Repeat behind. Only sink these top two corners. If this step is too difficult, you can simply refold ALL the mountain fold creases made in step 21. The closed sinks allow you to lock the fins together.
20. Close the model.
24. Valley fold flap and tuck into the pocket created by the closed sink in step 22. Repeat behind.
23. Collapse the model in half along existing creases. This is similar to collapsing a waterbomb base.
25. Finished! Pull �ns to CHOMP.
DRAFT
Hungry DRaculaDesign and Diagram by Beth JohnsonRecommended paper: 10 inch Duo Kami Difficulty Level: IntermediateDiagrams and models may be reproduced only for personal use, and may not be redistributed or republished in any way without my permission.
1. Fold and unfold. 2. Fold edges to center. 3. Fold in half and unfold.
4. Fold and unfold. 5. Turn model over. 6. Fold and unfold thecorners to the center.
7. Fold and unfold.
8. Fold and unfold. 9. Refold creases made in step 4.
10. Valley fold and unfold angle bisector.
11. Mountain fold creasemade in step 10.
DRAFT
10-11
10-11
13-14
13-14 13-14
12 Repeat steps 10-11 on the other three sides.
13. Crimp the model usingexisting creases (can be considered an open sink).Model will not lie flat.
13a. Model opened up to show crease pattern of the collapse.
14.Inside reverse fold along the creases made in step 6.
15. Repeat steps 13-14 on the other three sides. Model will lie flat along midline after all sides are collapsed.
16. Result. Fold all layers to the halfway point of the side edge. Unfold.
10-11
17. Result. Open up model towork on the layers inside. Model will not lie flat.
1/2
18.Gently pull out the top twolayers of the highlighted areato work on the next few steps.
19. Fold top corner.
DRAFT
32.Close sink the corner. Repeat behind. Only sink these top two corners. If this step is too difficult, you can simply refold ALL the mountain fold crease made in step 20. The closed sinks allow you to lock the cape together.
20. Fold along creasemade in step 16.
21. Fold so edge A (hidden) lies along edge B.
22. Unfold to step 19.23. Outside reverse fold.
AB
24. Sink the layers by crimping along existingcreases.
25. Fold and unfold through all layers.
26. Tuck top and bottom layer inside.
27. Result. Zoom out.
18-27
28. Repeat steps 18-27on the right side.
29. Close model. 30. Repeat steps 16-29on the bottom half of the model.
16-29
31. Mountain fold and unfold the edges. Repeat behind.
DRAFT
33. Outside reverse foldthe two corners alongexisting creases.
34. Collapse model in half along existing creases. This is similar to collapsing a waterbomb base.
35. Valley fold flap and tuck into the pocket created by the closed sink in step 22. Repeat behind.
36. Shape the lips by rollingover the top edge of the paper.
37. Result. Rotate model to view it from the top.
38. Top view. Valley fold alllayers by gently rolling upthe back. Do not crease sharply.
40. Finished! Pull side of cape to make him CHOMP.39. Result, view from the side.
top
DRAFT