compack living 180° technical manual rev4 eng
DESCRIPTION
ÂTRANSCRIPT
CELEGON S.r.l. - Via G. Galilei, 6 - 30035 Mirano (Venezia) - T +39 (0)41 5728404 - F +39 (0)41 5728522www.compackliving.com - [email protected]
MTCL180EN - Rev. 04-03/2015
TECHNICAL CONSTRUCTION MANUALCOMPACK LIVING 180° system
2
COMPACK LIVING 180° patented
MTCL180EN - Rev. 04-03/2015
The company reserved the right to make, at any time, without prior notice, all technical changes it considers appro-priate to improve the quality and the correct functionality of the products.
All contents of this manual are covered by copyright.It’s forbidden even partial reproduction of text and drawings, without prior written permission of Celegon s.r.l.. Any abuse will be prosecuted according to law.
All right reserved - Duplication or divulgation without autorization is strictly forbidden.
CONTENTS
1. INTRODUCTION ........................................................................... 32. COMPATIBILITY OF THE COMPACK LIVING SYSTEM ................................. 43. VARIANTS OF USE ........................................................................ 53.1 Hardware .................................................................................................. 63.2 Vertical section .......................................................................................... 73.3 Horizontal section left door ........................................................................... 83.4 Dimensional diagram of the door - symmetric leaves (Version 1) ............................. 93.5 Dimensional diagram of the door - asymmetric leaves (Version 2) .......................... 103.6 Dimensional diagram of the door - asymmetric leaves (Version 3) .......................... 113.7 Dimensional diagram of the door - asymmetric leaves (Version 4) .......................... 123.8 Dimensional diagram of the door - asymmetric leaves (Version 5) .......................... 13
4. DIMENSIONAL SUMMARIES ............................................................ 144.1 Single opening door ................................................................................... 144.2 Dimensional diagram of the double opening door .............................................. 154.3 COMPACK LIVING 180° - 90° combination possibilities on double doors ................... 164.4 Double opening door .................................................................................. 17
5. COMPONENTS ........................................................................... 185.1 Wood components compatible with COMPACK LIVING 90° .................................... 185.2 Door leaf hinge side (compatible with COMPACK LIVING 90°) ................................ 195.3 Door leaf handle side (compatible with COMPACK LIVING 90°) .............................. 205.4 Workings for accessories (compatible with COMPACK LIVING 90°) .......................... 215.5 Door hardware mounting hole diagrams (compatible with COMPACK LIVING 90°) ....... 225.6 Hinge side door jamb (compatible with COMPACK LIVING 90°) .............................. 235.7 Handle side door jamb (compatible with COMPACK LIVING 90°) ............................ 245.8 Upper crossbeam (compatible with COMPACK LIVING 90°) ................................... 25
6. ASSEMBLY ................................................................................ 266.1 Assembling the hardware on the leaf ............................................................. 266.2 Assembling the hardware on the jamb ............................................................ 276.3 Installation door leaf on the jambs ................................................................ 28
7. ADJUSTMENT OF SECONDARY STOP ................................................ 298. SPECIAL COMPACK LIVING MAGNETIC LATCH ...................................... 308.1 Examples for using the special COMPACK LIVING lock ......................................... 31
3
COMPACK LIVING 180° patented
MTCL180EN - Rev. 04-03/2015
1. INTRODUCTIONThe COMPACK LIVING 180° system opens up new possibilities in interior design. Thanks to its re-duced space requirements, silent operation and acoustic insulation properties, COMPACK LIVING 180° offers an alternative to traditional swing doors, doors that slide into or along the wall, ac-cordion doors, and rototranslating doors. Furthermore, COMPACK LIVING 180° may be applied to moveable walls and closets.
The COMPACK LIVING 180° system, installed between the top edge of the leaf and the lintel, makes it possible to confine the movement of the door leaf to one side of the wall and thus to recover usable space.
The COMPACK LIVING systems are designed for extreme simplicity and speed of installation.
There are no height or width constraints for the COMPACK LIVING systems. The combined weight limit for the two leaves is 50 kg. The maximum door leaf thickness depends on frame thickness (see paragraphs 3.2 and 3.3).
COMPACK LIVING 180° uses either traditional door latches (for use with paired lever handles or knobs) or a special COMPACK magnetic latch (for a lever handle on one side and a recessed handle on the other). With the COMPACK latch the recessed handle can be used to operate the latch. This system provides 180° rotation (see Section 8. SPECIAL COMPACK MAGNETIC LATCH).
The COMPACK LIVING systems provide stable, silent and ergonomic door operation. Stop on three sides ensures excellent acoustic insulation when the door is closed. These systems leave maximum technical and aesthetic freedom in designing the door. Doors can be constructed in various ver-sions to respond to the countless customer needs and to fit oversized dimensions.
The COMPACK LIVING systems are composed of steel plates and arms connected together by steel pins and plastic O-rings.
The door leaves are prepared in the same way for 90° or 180° opening. The same stock of semi-fi-nished materials (doors leaves) and same preparatory work (milling, drilling) allow installation either of the COMPACK LIVING 90° hinge for a door opening to 90° or the COMPACK LIVING 180° hinge for a door opening to 180°.
The hardware is cleaned using a soft cloth being careful not to move the door during the cleaning process to prevent injury.
Risk of pinching or cutting: never put your hands in among the moving arms when in-stalling or operating the door.
Give the information sheets including in the package to the final user.
Bonetti Massimo Design
4
COMPACK LIVING 180° patented
COMPACK 180°COMPACK 90°
COMPACK 180°COMPACK 90°
MTCL180EN - Rev. 04-03/2015
2. COMPATIBILITY OF THE COMPACK LIVING SYSTEM
SAME DOOR LEAVESIdentical size and design
5
COMPACK LIVING 180° patented
MTCL180EN - Rev. 04-03/2015
3. VARIANTS OF USE
To get the most out of the variants illustrated on this page, see the specifications for using the COM-PACK latch (see Section 8. SPECIAL COMPACK LIVING MAGNETIC LATCH).
· Version 1 Symmetric door leavesBy using the handle only on one side and the recessed handle on the other, is necessary to apply the magnetic lock COMPACK.Version possible with all available items RIGHT/LEFT.
· Version 2 Asymmetric door leaves with handle leaf from 0 to + 50 largerBy using the handle only on one side and the recessed handle on the other, is necessary to apply the magnetic lock COMPACK.Version possible with all available items RIGHT/LEFT.
· Version 3 Asymmetric door leaves with handle leaf from 0 to - 50 lowerBy using the handle only on one side and the recessed handle on the other, is necessary to apply the magnetic lock COMPACK.Version possible with all available items RIGHT/LEFT.
· Version 4 Asymmetric door leaves with handle leaf from 100 to + 150 largerTraditional lock with knobs or half handles.Version possible with all available items RIGHT/LEFT.
· Version 5 Asymmetric door leaves with handle leaf from 150 to + 200 largerTraditional lock with traditional handles.Version possible with all available items RIGHT/LEFT.
6
COMPACK LIVING 180° patented
570
510
530520
550
560
500540
550
MTCL180EN - Rev. 04-03/2015
3.1 Hardware
Part listRef. Q.ty Description500 1 Compack Living system RH or LH510 1 Central hinge lower520 1 Lateral hinge lower for leaf RH or LH530 1 Lateral hinge lower for jamb RH or LH540 4 Screw TSP trx ø 4x20550 16 Screw TSP trx ø 4x30560 1 Invisible hinge for alignment leaves570 1 Magnetic lock Compack Living with strikers
and special square spindle (optional)
7
COMPACK LIVING 180° patented
e
40
56
5
40 ÷ 44 (*)
HA
= H
FM-3
5
HP
= H
FM-5
0
HFM
500
530520
MTCL180EN - Rev. 04-03/2015
3.2 Vertical section
HFM = Wall Hole HeightHP = Passage DimensionHA = Leaf Height
Part listRef. Q.ty Description500 1 Compack Living 180 system RH or LH520 1 Lateral hinge lower for leaf RH or LH530 1 Lateral hinge lower for jamb RH or LHe 1 Upper crossbeam
(*) Leaf/track cover moulding thickness ratioleaf thickness flat casing thickness
40 10 ÷ 1442 10 ÷ 1244 10
mm seal gap
Door jambrabbetside
leaf
flat casing
flat casing
8
COMPACK LIVING 180° patented
40 ÷
44*
10 ÷
14*
8
44
c
a
b
110
50
4040
3
1
3
5
40 ÷
44*
10 ÷
14*
50
510c
a b
d
530520
40 ÷
44*
LS = LFM-100
LFM
LA = LFM-86
570
MTCL180EN - Rev. 04-03/2015
3.3 Horizontal section left door
Example of Left Door (Right door is symmetric)
LFM = Wall Hole WidthES = Outer JambLS = Door Jamb OpeningLA = Leaf Width
(*) Leaf/track cover moulding thickness ratioleaf thickness flat casing thickness
40 10 ÷ 1442 10 ÷ 1244 10
Part listRef. Q.ty Description510 1 Central hinge lower520 1 Lateral hinge lower for leaf RH or LH530 1 Lateral hinge lower for jamb RH or LH570 1 Magnetic lock Compack Living with strikers
and special square spindle (optional)a 1 Hinge leafb 1 Handle leafc 1 Hinge side door jambd 1 Handle side door jamb
ES= LFM-20 (= length of the upper crossbeam)
L hinge leaf L handle leaf
5 m
m S
eal g
ap
Door jambrabbet side
Door jambrabbet side
flat casing
flat casing
flat casing
9
COMPACK LIVING 180° patented
40 ÷
44*
16 1
Z
110
V
LP=LFM-108
LFM
MTCL180EN - Rev. 04-03/2015
3.4 Dimensional diagram of the door - symmetric leaves (Version 1)
Version 1 - symmetric leavesLFM LP L** hinge leaf L** handle leaf Z V art. COMPACK700 592 306,5 306,5 355 250 800F60DX 800F60SX
800 692 356,5 356,5 405 300 800F70DX 800F70SX
900 792 406,5 406,5 455 350 800A80DX 800A80SX
1000 892 456,5 456,5 505 400 800B90DX 800B90SX
1100 992 506,5 506,5 555 450 800B100DX 800B100SX
Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES)
Version 1 - symmetric leavesart. COMPACK L** hinge leaf dimension X L** handle leaf dimension Y
800F60DX 800F60SX 306,5 208 306,5 234
800F70DX 800F70SX 356,5 208 356,5 234
800A80DX 800A80SX 406,5 258 406,5 284
800B90DX 800B90SX 456,5 358 456,5 384
800B100DX 800B100SX 506,5 358 506,5 384
LFM = Wall Hole WidthLP = Passage DimensionZ = Encumbrance in openingV = Encumbrance on the wall
(**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.
Example of Left Door(Right door is symmetric)
It’s possible to use the pair of handles or traditional knobs by adjusting the secon-dary stop (see chapter 7)
L** handle leaf
L** hinge leaf= (LFM-87)/2
L** handle leafL** hinge leaf
Y (compatible with 90°)
X (compatible with 90°)
10
COMPACK LIVING 180° patented
V
0 ÷ 50
Z
110
LFM
LP
40 ÷
44*
16 1
MTCL180EN - Rev. 04-03/2015
3.5 Dimensional diagram of the door - asymmetric leaves (Version 2)
Handle leaf from 0 to +50 larger
Version 2 - asymmetric leaves (handle leaf from 0 to +50 larger)LFM LP L** hinge leaf L** handle leaf Z V art. COMPACK
700 ÷ 750 592 306,5 306,5 ÷ 356,5 355 250 800F60DX 800F60SX
800 ÷ 850 692 356,5 356,5 ÷ 406,5 405 300 800F70DX 800F70SX
900 ÷ 950 792 406,5 406,5 ÷ 456,5 455 350 800A80DX 800A80SX
1000 ÷ 1050 892 456,5 456,5 ÷ 506,5 505 400 800B90DX 800B90SX
1100 ÷ 1150 992 506,5 506,5 ÷ 556,5 555 450 800B100DX 800B100SX
Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES)
Version 2 - asymmetric leaves (handle leaf from 0 to +50 larger)art. COMPACK L** hinge leaf dimension X L** handle leaf dimension Y
800F60DX 800F60SX 306,5 208 306,5 ÷ 356,5 234
800F70DX 800F70SX 356,5 208 256,5 ÷ 356,5 234
800A80DX 800A80SX 406,5 258 306,5 ÷ 406,5 284
800B90DX 800B90SX 456,5 358 356,5 ÷ 456,5 384
800B100DX 800B100SX 506,5 358 406,5 ÷ 506,5 384
LFM = Wall Hole WidthLP = Passage DimensionZ = Encumbrance in openingV = Encumbrance on the wall
(**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.
Example of Left Door(Right door is symmetric)
It’s possible to use the pair of handles or traditional knobs by adjusting the secon-dary stop (see chapter 7)
L** handle leaf
L** hinge leaf
L** handle leafL** hinge leaf
Y (compatible with 90°)
X (compatible with 90°)
11
COMPACK LIVING 180° patented
Z
110
V
0 ÷ -50
LFM
LP = LFM-108
40 ÷
44*
16 1
MTCL180EN - Rev. 04-03/2015
3.6 Dimensional diagram of the door - asymmetric leaves (Version 3)
Handle leaf from 0 to -50 lower
Version 3 - asymmetric leaves (handle leaf from 0 to -50 lower)LFM LP L** hinge leaf L** handle leaf Z V art. COMPACK
650 ÷ 700 542 ÷ 592 306,5 256,5 ÷ 306,5 355 250 800F60DX 800F60SX
750 ÷ 800 642 ÷ 692 356,5 306,5 ÷ 356,5 405 300 800F70DX 800F70SX
850 ÷ 900 742 ÷ 792 406,5 356,5 ÷ 406,5 455 350 800A80DX 800A80SX
950 ÷ 1000 842 ÷ 892 456,5 406,5 ÷ 456,5 505 400 800B90DX 800B90SX
1050 ÷ 1100 942 ÷ 992 506,5 456,5 ÷ 506,5 555 450 800B100DX 800B100SX
Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES)
Version 3 - asymmetric leaves (handle leaf from 0 to -50 lower)art. COMPACK L** hinge leaf dimension X L** handle leaf dimension Y
800F60DX 800F60SX 306,5 208 256,5 ÷ 306,5 234
800F70DX 800F70SX 356,5 208 306,5 ÷ 356,5 234
800A80DX 800A80SX 406,5 258 356,5 ÷ 406,5 284
800B90DX 800B90SX 456,5 358 406,5 ÷ 456,5 384
800B100DX 800B100SX 506,5 358 456,5 ÷ 506,5 384
LFM = Wall Hole WidthLP = Passage DimensionZ = Encumbrance in openingV = Encumbrance on the wall
Example of Left Door(Right door is symmetric)
(**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.
It’s possible to use the pair of handles or traditional knobs by adjusting the secon-dary stop (see chapter 7)
L** handle leaf
L** hinge leaf
L** handle leafL** hinge leaf
Y (compatible with 90°)
X (compatible with 90°)
12
COMPACK LIVING 180° patented
Z
110
V
100 ÷ 150
LFM
LP
40 ÷
44*
16 1
MTCL180EN - Rev. 04-03/2015
3.7 Dimensional diagram of the door - asymmetric leaves (Version 4)
Handle leaf from +100 to +150 larger
Version 4 - asymmetric leaves (handle leaf from +100 to +150 larger)LFM LP L** hinge leaf L** handle leaf Z V art. COMPACK
800 ÷ 850 592 306,5 406,5 ÷ 456,5 355 250 800F60DX 800F60SX
900 ÷ 950 692 356,5 456,5 ÷ 506,5 405 300 800F70DX 800F70SX
1000 ÷ 1050 792 406,5 506,5 ÷ 556,5 455 350 800A80DX 800A80SX
1100 ÷ 1150 892 456,5 556,5 ÷ 606,5 505 400 800B90DX 800B90SX
1200 ÷ 1250 992 506,5 606,5 ÷ 656,5 555 450 800B100DX 800B100SX
Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES)
Version 4 - asymmetric leaves (handle leaf from +100 to +150 larger)art. COMPACK L** hinge leaf dimension X L** handle leaf dimension Y
800F60DX 800F60SX 306,5 208 406,5 ÷ 456,5 234
800F70DX 800F70SX 356,5 208 456,5 ÷ 506,5 234
800A80DX 800A80SX 406,5 258 506,5 ÷ 556,5 284
800B90DX 800B90SX 456,5 358 556,5 ÷ 606,5 384
800B100DX 800B100SX 506,5 358 606,5 ÷ 656,5 384
LFM = Wall Hole WidthLP = Passage DimensionZ = Encumbrance in openingV = Encumbrance on the wall
Example of Left Door(Right door is symmetric)
(**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.
L** handle leaf
L** hinge leaf
L** handle leafL** hinge leaf
Y (compatible with 90°)
X (compatible with 90°)
13
COMPACK LIVING 180° patented
Z
110
V
150 ÷ 200
LFM
LP
40 ÷
44*
16 1
MTCL180EN - Rev. 04-03/2015
3.8 Dimensional diagram of the door - asymmetric leaves (Version 5)
Handle leaf from +150 to +200 larger
Version 5 - asymmetric leaves (handle leaf from +150 to +200 larger)LFM LP L** hinge leaf L** handle leaf Z V art. COMPACK
850 ÷ 900 592 306,5 456,5 ÷ 506,5 355 250 800F60DX 800F60SX
950 ÷ 1000 692 356,5 506,5 ÷ 556,5 405 300 800F70DX 800F70SX
1050 ÷ 1100 792 406,5 556,5 ÷ 606,5 455 350 800A80DX 800A80SX
1150 ÷ 1200 892 456,5 606,5 ÷ 656,5 505 400 800B90DX 800B90SX
1250 ÷ 1300 992 506,5 656,5 ÷ 706,5 555 450 800B100DX 800B100SX
Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES)
Version 5 - asymmetric leaves (handle leaf from +150 to +200 larger)art. COMPACK L** hinge leaf dimension X L** handle leaf dimension Y
800F60DX 800F60SX 306,5 208 456,5 ÷ 506,5 234
800F70DX 800F70SX 356,5 208 506,5 ÷ 556,5 234
800A80DX 800A80SX 406,5 258 556,5 ÷ 606,5 284
800B90DX 800B90SX 456,5 358 606,5 ÷ 656,5 384
800B100DX 800B100SX 506,5 358 656,5 ÷ 706,5 384
LFM = Wall Hole WidthLP = Passage DimensionZ = Encumbrance in openingV = Encumbrance on the wall
Example of Left Door(Right door is symmetric)
(**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.
L** handle leaf
L** hinge leaf
L** handle leafL** hinge leaf
Y (compatible with 90°)
X (compatible with 90°)
14
COMPACK LIVING 180° patented
MTCL180EN - Rev. 04-03/2015
4. DIMENSIONAL SUMMARIES4.1 Single opening doorThe following form is a summary all of possible realizable dimensions with the measurements.The COMPACK LIVING 180° system foresee a minimum wall opening (LFM) of 700 mm with sym-metric leaves and of 650 mm with asymmetric leaves.The maximum wall opening (LFM) with symmetric leaves is 1100 mm.For measuremnts of LFM larger than 1100 mm is necessary to increase the dimensions of the handle door leaf.
Summary dimensions for single opening doorWall Hole
Width LFM
Version Jut HandleDoor Leaf
Passage Dimension
LP
FixDimensionL** hinge
leaf
Workingdimension x
Variable DimensionL** handle
leaf
Workingdimension y
Encumbrance in opening
Z
Encumbranceon the wall
Vart. COMPACK
650÷700 3 asymmetricfrom -50 to 0 542÷592 306,5 208 256,5÷306,5 234 355 250 800F60DX 800F60SX
700 1 symmetric0 592 306,5 208 306,5 234 355 250 800F60DX 800F60SX
700÷750 2 asymmetricfrom 0 to +50 592 306,5 208 306,5÷356,5 234 355 250 800F60DX 800F60SX
750÷800 3 asymmetricfrom -50 to 0 642÷692 356,5 208 306,5÷356,5 234 405 300 800F70DX 800F70SX
800 1 symmetric0 692 356,5 208 356,5 234 405 300 800F70DX 800F70SX
800÷850 2 asymmetricfrom 0 to +50 692 356,5 208 356,5÷406,5 234 405 300 800F70DX 800F70SX
800÷850 4 asymmetricfrom +100 to +150 592 306,5 208 406,5÷456,5 234 355 250 800F60DX 800F60SX
850÷900 3 asymmetricfrom -50 to 0 742÷792 406,5 258 356,5÷406,5 284 455 350 800A80DX 800A80SX
850÷900 5 asymmetricfrom +150 to +200 592 306,5 208 456,5÷506,5 234 355 250 800F60DX 800F60SX
900 1 symmetric0 792 406,5 258 406,5 284 455 350 800A80DX 800A80SX
900÷950 2 asymmetricfrom 0 to +50 792 406,5 258 406,5÷456,5 284 455 350 800A80DX 800A80SX
900÷950 4 asymmetricfrom +100 to +150 692 356,5 208 456,5÷506,5 234 405 300 800F70DX 800F70SX
950÷1000 3 asymmetricfrom -50 to 0 842÷892 456,5 358 406,5÷456,5 384 505 400 800B90DX 800B90SX
950÷1000 5 asymmetricfrom +150 to +200 692 356,5 208 506,5÷556,5 234 405 300 800F70DX 800F70SX
1000 1 symmetric0 892 456,5 358 456,5 384 505 400 800B90DX 800B90SX
1000÷1050 2 asymmetricfrom 0 to +50 892 456,5 358 456,5÷506,5 384 505 400 800B90DX 800B90SX
1000÷1050 4 asymmetricfrom +100 to +150 792 406,5 258 506,5÷556,5 284 455 350 800A80DX 800A80SX
1050÷1100 3 asymmetricfrom -50 to 0 942÷992 506,5 358 456,5÷506,5 384 555 450 800B100DX 800B100SX
1050÷1100 5 asymmetricfrom +150 to +200 792 406,5 258 556,5÷606,5 284 455 350 800A80DX 800A80SX
1100 1 symmetric0 992 506,5 358 506,5 384 555 450 800B100DX 800B100SX
1100÷1150 2 asymmetricfrom 0 to +50 992 506,5 358 506,5÷556,5 384 555 450 800B100DX 800B100SX
1100÷1150 4 asymmetricfrom +100 to +150 892 456,5 358 556,5÷606,5 384 505 400 800B90DX 800B90SX
1150÷1200 5 asymmetricfrom +150 to +200 892 456,5 358 606,5÷656,5 384 505 400 800B90DX 800B90SX
1200÷1250 4 asymmetricfrom +100 to +150 992 506,5 358 606,5÷656,5 384 555 450 800B100DX 800B100SX
1250÷1300 5 asymmetricfrom +150 to +200 992 506,5 358 656,5÷706,5 384 555 450 800B100DX 800B100SX
15
COMPACK LIVING 180° patented
456,5 496,5
1
496,5 456,5
133 3
8 8
LFMD 2000
ESD=LFMD-23 (1977)
LSD=LFMD-103 (1897)
LPD (1801)
40
40
40
40
MTCL180EN - Rev. 04-03/2015
4.2 Dimensional diagram of the double opening door
Dimensional exampleAttention: you need to use two hardwares COMPACK LIVING, one right and one left.
LFMD = Double Wall Opening WidthESD = External Jamb Double (LFMD-23)LSD = Light Jamb Double (LFMD-103)LPD = Width Passagge Double Door Leaf
Art. COMPACK 800B90SX Art. COMPACK 800B90DX
hinge leaf hinge leafhandle leaf
= difference between handle door leafwidth and hinge door leaf
handle leaf
16
COMPACK LIVING 180° patented
180°180°
180°
90°90°
90°
MTCL180EN - Rev. 04-03/2015
- Possible combinations using the same components in wood
4.3 COMPACK LIVING 180° - 90° combination possibilities on double doors
17
COMPACK LIVING 180° patented
MTCL180EN - Rev. 04-03/2015
4.4 Double opening doorThe following form is a summary all of possible realizable dimensions with the measurements.The COMPACK LIVING 180° system foresee a minimum wall opening (LFM) of 1320 mm with sym-metric leaves and of 1220 mm with asymmetric leaves.The maximum wall opening (LFM) with symmetric leaves is 2120 mm.For measuremnts of LFM larger than 2120 mm is necessary to increase the dimensions of the handle door leaf.
Summary dimensions for double opening doorWall Hole
Width LFM
Version Jut HandleDoor Leaf
Passage Dimension
LP
FixDimensionL** hinge
leaf
Workingdimension x
Variable DimensionL** handle
leaf
Workingdimension y
Encumbrance in opening
Z
Encumbranceon the wall
Vart. COMPACK
1220÷1320 3 asymmetricfrom -50 to 0 1101÷1201 306,5 208 256,5÷306,5 234 355 250 800F60DX 800F60SX
1320 1 symmetric0 1201 306,5 208 306,5 234 355 250 800F60DX 800F60SX
1320÷1420 2 asymmetricfrom 0 to +50 1201 306,5 208 306,5÷356,5 234 355 250 800F60DX 800F60SX
1420÷1520 3 asymmetricfrom -50 to 0 1301÷1401 356,5 208 306,5÷356,5 234 405 300 800F70DX 800F70SX
1520 1 symmetric0 1401 356,5 208 356,5 234 405 300 800F70DX 800F70SX
1520÷1620 2 asymmetricfrom 0 to +50 1401 356,5 208 356,5÷406,5 234 405 300 800F70DX 800F70SX
1520÷1620 4 asymmetricfrom +100 to +150 1201 306,5 208 406,5÷456,5 234 355 250 800F60DX 800F60SX
1620÷1720 3 asymmetricfrom -50 to 0 1501÷1601 406,5 258 356,5÷406,5 284 455 350 800A80DX 800A80SX
1620÷1720 5 asymmetricfrom +150 to +200 1201 306,5 208 456,5÷506,5 234 355 250 800F60DX 800F60SX
1720 1 symmetric0 1601 406,5 258 406,5 284 455 350 800A80DX 800A80SX
1720÷1820 2 asymmetricfrom 0 to +50 1601 406,5 258 406,5÷456,5 284 455 350 800A80DX 800A80SX
1720÷1820 4 asymmetricfrom +100 to +150 1401 356,5 208 456,5÷506,5 234 405 300 800F70DX 800F70SX
1820÷1920 3 asymmetricfrom -50 to 0 1701÷1801 456,5 358 406,5÷456,5 384 505 400 800B90DX 800B90SX
1820÷1920 5 asymmetricfrom +150 to +200 1401 356,5 208 506,5÷556,5 234 405 300 800F70DX 800F70SX
1920 1 symmetric0 1801 456,5 358 456,5 384 505 400 800B90DX 800B90SX
1920÷2020 2 asymmetricfrom 0 to +50 1801 456,5 358 456,5÷506,5 384 505 400 800B90DX 800B90SX
1920÷2020 4 asymmetricfrom +100 to +150 1601 406,5 258 506,5÷556,5 284 455 350 800A80DX 800A80SX
2020÷2120 3 asymmetricfrom -50 to 0 1801÷1901 506,5 358 456,5÷506,5 384 555 450 800B100DX 800B100SX
2020÷2120 5 asymmetricfrom +150 to +200 1601 406,5 258 556,5÷606,5 284 455 350 800A80DX 800A80SX
2120 1 symmetric0 2001 506,5 358 506,5 384 555 450 800B100DX 800B100SX
2120÷2220 2 asymmetricfrom 0 to +50 2001 506,5 358 506,5÷556,5 384 555 450 800B100DX 800B100SX
2120÷2220 4 asymmetricfrom +100 to +150 1801 456,5 358 556,5÷606,5 384 505 400 800B90DX 800B90SX
2220÷2320 5 asymmetricfrom +150 to +200 1801 456,5 358 606,5÷656,5 384 505 400 800B90DX 800B90SX
2320÷2420 4 asymmetricfrom +100 to +150 2001 506,5 358 606,5÷656,5 384 555 450 800B100DX 800B100SX
2420÷2520 5 asymmetricfrom +150 to +200 2001 506,5 358 656,5÷706,5 384 555 450 800B100DX 800B100SX
18
COMPACK LIVING 180° patented
e
d
cb
a
MTCL180EN - Rev. 04-03/2015
5. COMPONENTS5.1 Wood components compatible with COMPACK LIVING 90°
Part listRef. Q.ty Description
a 1 Hinge leafb 1 Handle leafc 1 Hinge side door jambd 1 Handle side door jambe 1 Upper crossbeam
19
COMPACK LIVING 180° patented
16
17
9,5
8
23
X **
9
2
7
7
40 ÷ 44
A
B
HA =
HFM
- 3
5
R9
3
23
9,5
86
16 B
A
R992,5
23
7
7
7
23
9,53
45°
4
R1R1
MTCL180EN - Rev. 04-03/2015
5.2 Door leaf hinge side (compatible with COMPACK LIVING 90°)
Left leaf door hinge side (Right door is symmetric)
(**) For dimensions see sections 3.4, 3.5, 3.6, 3.7, 3.8
HFM = Wall Hole HeightHA = Leaf Height
L** hinge leaf
L** hinge leaf
door jambrabbet side
door jambrabbet side
door jambrabbet side
door jambrabbet side
Upper edge detail
20
COMPACK LIVING 180° patented
R9
R9Y **
9
5
118 32,5
R97
23
92,5
9,5
23
3
7
7
A
HA =
HFM
- 3
5
A
40÷44
MTCL180EN - Rev. 04-03/2015
5.3 Door leaf handle side (compatible with COMPACK LIVING 90°)
Left leaf door handle side (Right door is symmetric)
(**) For dimensions see sections 3.4, 3.5, 3.6, 3.7, 3.8
HFM = Wall Hole HeightHA = Leaf Height
L** handle leaf
L** handle leaf
Upper edge detail
door jambrabbet side
door jambrabbet side
door jambrabbet side
21
COMPACK LIVING 180° patented
570
3
8050
18
16
145
196
19
16
8018
19
50
85
50
3
14519
6
560
MTCL180EN - Rev. 04-03/2015
5.4 Workings for accessories (compatible with COMPACK LIVING 90°)
The workings indicated for lock seat are absoluty needed if a complete folding of the leaves pair in opening in the versions 1, 2 and 3 is requested.
Part listRef. Q.ty Description560 1 Invisible hinge for alignment leaves570 1 Magnetic lock Compack Living with strikers
and special square spindle (optional)
Seat for invisible hinge
COMPACK LIVINGmagneticlock seat(optional)
door jamb rabbet side
door jamb rabbet side
door jamb rabbet side
Optional
22
COMPACK LIVING 180° patented
25
23
==
17 1964 64
32.5=
=
66.380 80104.58.7
25
23
==
17 1964 64
32.5=
=
58.280 80154.516.8
25
23
==
17 1964 64
32.5=
=
6435.480 80204.525.6
25
23
==
17 1964 64
32.5=
=
64137.480 80254.523.6
25
23
==
17 1964 64
32.5=
=
64 39.2121.780 80304.5
MTCL180EN - Rev. 04-03/2015
5.5 Door hardware mounting hole diagrams (compatible with COMPACK LIVING 90°)
Door hardware mounting holes for both door systems: 180° and 90°
Hardware group F60Art. 800F60SX - 800F60DXArt. 900F60SX - 900F60DX
Hardware group F70Art. 800F70SX - 800F70DXArt. 900F70SX - 900F70DX
Hardware group A80Art. 800A80SX - 800A80DXArt. 900A80SX - 900A80DX
Hardware group B90Art. 800B90SX - 800B90DXArt. 900B90SX - 900B90DX
Hardware group B100Art. 800B100SX - 800B100DXArt. 900B100SX - 900B100DX
Only for Compack Living 90°
Only for Compack Living 90°
Only for Compack Living 90°
Only for Compack Living 90°
Only for Compack Living 90°
Only for Compack Living 180°
Only for Compack Living 180°
Only for Compack Living 180°
Only for Compack Living 180°
Only for Compack Living 180°
23
COMPACK LIVING 180° patented
18
3
15*
4037*
30
X
X
18 15*
3
5
26
72
HFM
- 2
4
30
10
MTCL180EN - Rev. 04-03/2015
5.6 Hinge side door jamb (compatible with COMPACK LIVING 90°)
Door left jamb hinge side (Right jamb is symmetric)
X = Wall ThicknessHFM = Wall Hole Height
The dimension marked with (*) vary according to the seal gap dimensions
seal
gap
(see
sec
tion
3.2
)
low sidehinge seat
seal seat
24
COMPACK LIVING 180° patented
16
40
1030
37*
X
16
15
X
25*
25*
5
26
1030
HFM
- 2
4
50
MTCL180EN - Rev. 04-03/2015
5.7 Handle side door jamb (compatible with COMPACK LIVING 90°)
Door left jamb handle side (Right jamb is symmetric)
X = Wall ThicknessHFM = Wall Hole Height
The dimension marked with (*) vary according to the seal gap dimensions.
seal
gap
(see
sec
tion
3.2
)
COMPACK LIVINGmagnetic lockcatch seat
seal seat
25
COMPACK LIVING 180° patented
X
14
37*10
40
5
16
30
ES = LF
M-20
30
1441
X
MTCL180EN - Rev. 04-03/2015
5.8 Upper crossbeam (compatible with COMPACK LIVING 90°)
X = Wall ThicknessES = Outer Jamb (= length of the upper crossbeam)LFM = Wall Hole Width
The dimension marked with (*) vary according to the seal gap dimensions.
seal gap(see section 3.2)seal seat
26
COMPACK LIVING 180° patented
500
550
570
510
550
550
520
560
OK
= =
1
1
==
MTCL180EN - Rev. 04-03/2015
6. ASSEMBLY6.1 Assembling the hardware on the leaf
Part listRef. Q.ty Description500 1 Compack Living 180 system RH or LH510 1 Central hinge lower520 1 Lateral hinge lower for leaf RH or LH550 14 Screw TSP trx ø 4x30560 1 Invisible hinge for alignment leaf570 1 Magnetic lock Compack Living with strikers
and special square spindle (optional)
27
COMPACK LIVING 180° patented
550
530
570
MTCL180EN - Rev. 04-03/2015
6.2 Assembling the hardware on the jamb
Part listRef. Q.ty Description530 1 Lateral hinge lower for jamb RH or LH550 2 Screw TSP trx ø 4x30570 1 Magnetic lock Compack Living with strikers
and special square spindle (optional)
28
COMPACK LIVING 180° patented
540
1
3
2
3
2
MTCL180EN - Rev. 04-03/2015
6.3 Installation door leaf on the jambs
Part listRef. Q.ty Description540 4 Screw TSP trx ø 4x20
See sequence below for fitting the door:1 fold the door leaves aganist one another2 mount the door on the pivot of the hinge lower3 position the top hardware pieces in perfect
alignment with the corner and screw in place (screws included)
29
COMPACK LIVING 180° patented
MTCL180EN - Rev. 04-03/2015
7. ADJUSTMENT OF SECONDARY STOPThe adjustable secondary stop is used when traditional paired door handles or knobs are used for versions 1, 2 and 3 (see chapter 3. VARIANTS OF USE).This also makes it possible to use a traditional lock.
To prevent the handle or knob from hitting the door when it is opened, the secobdary stop must be adjusted by using a 3 mm hex key with ball end.
* Important: after adjusting the stop, a floor-mounted doorstop should also be installed.
* recommendedfloor-mounted door stop
adjustable secondary stop
3 mm hex key with ball end
30
COMPACK LIVING 180° patented
90°
180°
0°
MTCL180EN - Rev. 04-03/2015
8. SPECIAL COMPACK LIVING MAGNETIC LATCHIf lever handles cannot be used because of the way the doors fold together, it is necessary to use the special COMPACK magnetic latch, which makes it possible to use a recessed handle on the lower section of the latch mechanism to lock the door or to retract the latch. This system provides 180° rotation. The special COMPACK magnetic latch also makes it possible to install the recessed handle on the upper section of the latch, to ensure privacy when the door opens into the room.
It is possible to use a traditional latch for paired handles only with variants 4 and 5 of the COM-PACK LIVING 180° system (see Section 3. VARIANTS OF USE), or by using the secondary stop (see Section 7, ADJUSTMENT OF SECONDARY STOP).
With the COMPACK hinge, the recessed handle installed on the lower section of the latch fun-ctions as follows:
180° the recessed handle re-tract the lacth and opens the door
90° door unlocked the lever handle opens the door
0° door locked the lever handle does not open the door
COMPACK LIVINGmagnetic lock
OUTSIDE room INSIDE room
INSIDE room OUTSIDE room
Recessed handleon lower hole
Recessed handle on upper latch section,to ensure privacy when the door opens into the room.
To unite the lever handle with the recessed handle, use the special spindle in the latch pack
Upper spindle hole
31
COMPACK LIVING 180° patented
NO PRIVACY
B
4
A1
C
B
A
A3 A
3 B
4 B
2 B
2 C
1 B
1 C
2 A1 1 A1
MTCL180EN - Rev. 04-03/2015
8.1 Examples for using the special COMPACK LIVING lock
1 COMPACK LIVING 90° System opening to inside room
2 COMPACK LIVING 180° System opening to inside room
3 COMPACK LIVING 90° System opening to outside room
4 COMPACK LIVING 180° System opening to outside room
Traditional lever handle
Recessed handle with knob
Recessed handle
Special spindle square lock COMPACK(included in the lock’s package)
Expansion spindle square(available on the market)
Insideroom
Examples opening to inside room
Examples opening to outside room
Insideroom
Insideroom
Insideroom
Insideroom
Outsideroom
Outsideroom
Outsideroom
Outsideroom
Outsideroom
Com
posi
zion
e gr
afica
: Stu
dio
Gal
lo D
esig
n sr
l - C
ampo
sam
pier
o (P
D)
COMPACK living® è un’idea CELEGON30035 Mirano (Venezia) | Via G. Galilei, 6 - Z.I.
T +39 041 572 8404 | F +39 041 572 8522 www.compackliving.com | [email protected]
MTCL180EN - Rev. 04-03/2015