compact form - technical data sheets compact laminate
DESCRIPTION
Technical Data Sheets: Compact Laminate, Compact Exterior, Compactforming, Alucompact, Compact Core, Compact Wood, Compact Paint, Compact 2000TRANSCRIPT
Mod. COLAMI Rev. 1 del 10/05/2012
Compact LaminateTechnical Data and Certifications
MateriaL properties tested in aCCordanCe to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 ≥ 1,4
Thickness (e.g.) EN 438-2, point 5 mm 10
Weight kg/m2 14,0
Mechanical properties
Resistance against stress abrasion EN 438-2, point 10 U 450
Falling ball impact resistance EN 438-2, point 21 mm 8
Resistance against scratching EN 438-2, point 25 Degree 3
Scratch r. 4N
Flexural strength EN ISO 178 Mpa 100
E-Modulus EN ISO 178 Mpa 10 000
Tensile strength EN ISO 527-2 Mpa 60
Susceptibility to cracking EN 438-2, point 24 5
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % 0,05
cross. % 0,15
Resistance to boiling water EN 438-2, point 12 % 0,3
Coefficient of thermal expansion DIN 52328 1/K 20 × 10-6
Thermal conductivity W/mK ca. 0,3
Resistance to vapour diffusion μ 17 200
Surface resistance DIN 53482 Ohm 109-1011
Resistance to cigarette burns EN 438-2, point 30 Degree 5 - no visible changes1)
Resistance to hot soucepans EN 438-2, point 16 Degree 5 - no visible changes, no blisters or cracks2)
Heating value MJ/kg 18-20
Optical properties
Light fastness EN 438-2, point 27 Level 6-8
1) Slight change in glossy finish, yellow or light brown colours are permitted by EN 4382) Slight change in glossy finish permitted by EN 438* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture.
(Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. COLAMI Rev. 1 del 10/05/2012
Food ContaCt suitabiLity
Regarding the hygiene regulations concerning materials produced to have contact with foodstiffs (D.M. 4/4/85 - G.U. N° 10 Cee 123, 11/05/1983) it is declared that Compact Laminate conforms to the maximum values indicated in Annex IV, Section 2, Paragraph 1. It does not leave free formaldyde in quantities exceeding 0,5 mg/dm2, which is 3 p.p.m., with respect to the real or calculated capacity of the said objet.
max 3 p.p.m for occasional contact
max 0,5 p.p.m for prolonged occasion
reaCtion to Fire CLassiFiCation
Standard Class 2
Europe EN 13501-1 Euroclass D-s2, d0
Austria A3800/1 Tr1, Q1
Germany DIN 4102 B2
Class 1
Class 1 CSE RF 1/75/A – 3/77 Home Office Italy Approbation T0055A10CD100005
Class M1 CSTB Home Office France Certification 89.28703A
Class 1 BSI 476 part. 7: 1987 British Standard Institution UK Certification 49513
Compact LaminateTechnical Data and Certifications
Mod. COREST Rev. 1 del 10/05/2012
Compact ResistanceTechnical Data and Certifications
MateRial pRopeRties tested in aCCoRdanCe to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 ≥ 1,4
Thickness (e.g.) EN 438-2, point 5 mm 10
Weight kg/m2 14,0
Mechanical properties
Resistance against stress abrasion EN 438-2, point 10 U 450
Falling ball impact resistance EN 438-2, point 21 mm 8
Resistance against scratching EN 438-2, point 25 Degree 3
Scratch r. 4N
Flexural strength EN ISO 178 Mpa 100
E-Modulus EN ISO 178 Mpa 10 000
Tensile strength EN ISO 527-2 Mpa 60
Susceptibility to cracking EN 438-2, point 24 5
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % 0,05
cross. % 0,15
Resistance to boiling water EN 438-2, point 12 % 0,3
Coefficient of thermal expansion DIN 52328 1/K 20 × 10-6
Thermal conductivity W/mK ca. 0,3
Resistance to vapour diffusion μ 17 200
Surface resistance DIN 53482 Ohm 109-1011
Resistance to cigarette burns EN 438-2, point 30 Degree 5 - no visible changes1)
Resistance to hot soucepans EN 438-2, point 16 Degree 5 - no visible changes, no blisters or cracks2)
Heating value MJ/kg 18-20
Optical properties
Light fastness EN 438-2, point 27 Level 6-8
1) Slight change in glossy finish, yellow or light brown colours are permitted by EN 4382) Slight change in glossy finish permitted by EN 438* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture.
(Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. COREST Rev. 1 del 10/05/2012
ReaCtion to fiRe ClassifiCation
Standard Class 2
Europe EN 13501-1 Euroclass D-s2, d0
Austria A3800/1 Tr1, Q1
Germany DIN 4102 B2
Compact ResistanceTechnical Data and Certifications
Mod. COEXTE Rev. 1 del 10/05/2012
Compact ExteriorTechnical Data and Certifications
MatErial propErtiEs tEstEd in aCCordanCE to En 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density EN ISO 1183-1 g/cm3 1,45
Mechanical properties
Flexural strength EN ISO 178 Mpa ≥ 90
E-Modulus EN ISO 178 Mpa ≥ 9500
Tensile strength EN ISO 527-2 Mpa ≥ 80
Thermal properties
Coefficient of thermal expansion DIN 52328 1/K 18 × 10-6
Thermal conductivity W/mK 0,3
Resistance to vapour diffusion μ ca. 17 200
Artificial weathering EN ISO 4892-2 3000 hEN 20105-A02 greyscale
4-5
Optical properties
UV-light resistance EN ISO 4892-3 1500 hEN 20105-A02 greyscale
4-5
rEaCtion to firE ClassifiCation
Europe EN 13501-1 MA39-VFA Vienna Euroclass B-s2, d0 for 6-10 mm
Switzerland EMPA Dübendorf Fire classification 5.3 for 6 - 10 mm
Germany DIN 4102 Institute for Construction-Berlin B1 for 4 - 10 mm
France NFP 92501 LNE M1 for 2 - 10 mm
Spain UNE 23727-90 LICOF M1 for 6 - 10 mm
pErMits
Facade permit Germany Institute for Construction-Berlin 6, 8, 10 mm, Permit-No. Z-33.2-16
ETB guidelines for building components whichsafeguard against falls, June 1985. Balcony railings.
TU Hannover Passed (depending on building regulation and railing construction 6, 8 or 10 mm panel thickness)
Avis technique France CSTB 6, 8, 10 and 13 mm, wood- andmetal subconstruction, permit no.AT 2/07-1264, AT 2/07-1265
Mod. COFORM Rev. 1 del 10/05/2012
Compact FormingTechnical Data and Certifications
Material properties tested in aCCordanCe to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 ≥ 1,4
Thickness (e.g.) EN 438-2, point 5 mm 10
Weight kg/m2 14,0
Mechanical properties
Resistance against stress abrasion EN 438-2, point 10 U 450
Falling ball impact resistance EN 438-2, point 21 mm 8
Resistance against scratching EN 438-2, point 25 Degree 3
Scratch r. 4N
Flexural strength EN ISO 178 Mpa 100
E-Modulus EN ISO 178 Mpa 10 000
Tensile strength EN ISO 527-2 Mpa 60
Susceptibility to cracking EN 438-2, point 24 5
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % 0,05
cross. % 0,15
Resistance to boiling water EN 438-2, point 12 % 0,3
Coefficient of thermal expansion DIN 52328 1/K 20 × 10-6
Thermal conductivity W/mK ca. 0,3
Resistance to vapour diffusion μ 17 200
Surface resistance DIN 53482 Ohm 109-1011
Resistance to cigarette burns EN 438-2, point 30 Degree 5 - no visible changes1)
Resistance to hot soucepans EN 438-2, point 16 Degree 5 - no visible changes, no blisters or cracks2)
Heating value MJ/kg 18-20
Optical properties
Light fastness EN 438-2, point 27 Level 6-8
1) Slight change in glossy finish, yellow or light brown colours are permitted by EN 4382) Slight change in glossy finish permitted by EN 438* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture.
(Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. COFORM Rev. 1 del 10/05/2012
Food ContaCt suitability
Regarding the hygiene regulations concerning materials produced to have contact with foodstiffs (D.M. 4/4/85 - G.U. N° 10 Cee 123, 11/05/1983) it is declared that Compact Forming conforms to the maximum values indicated in Annex IV, Section 2, Paragraph 1. It does not leave free formaldyde in quantities exceeding 0,5 mg/dm2, which is 3 p.p.m., with respect to the real or calculated capacity of the said objet.
max 3 p.p.m for occasional contact
max 0,5 p.p.m for prolonged occasion
reaCtion to Fire ClassiFiCation
Standard Class 2
Europe EN 13501-1 Euroclass D-s2, d0
Austria A3800/1 Tr1, Q1
Germany DIN 4102 B2
Class 1
Class 1 CSE RF 1/75/A – 3/77 Home Office Italy Approbation T0055A10CD100005
Class M1 CSTB Home Office France Certification 89.28703A
Class 1 BSI 476 part. 7: 1987 British Standard Institution UK Certification 49513
Compact FormingTechnical Data and Certifications
Mod. ALUCOM Rev. 1 del 10/05/2012
AlucompactTechnical Data and Certifications
MAteriAl properties tested in AccordAnce to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Alucompact Alucompact Arrigo Alucompact 4, Alucompact 3 Mark1)
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 ca. 1,55 ca. 1,55 ca. 1,65
Thickness (e.g.) EN 438-2, point 5 mm 10 10 10
Weight kg/m2 15,5 15,5 16,5
Mechanical properties
Resistance against stress abrasion
EN 438-2, point 10 U 450 450 450
Falling ball impact resistance
EN 438-2, point 21 mm
Resistance against scratching
EN 438-2, point 25 degr./scratch r.
34N
34N
34N
Flexural strength EN ISO 178 Mpa 200 200 200
E-Modulus EN ISO 178 Mpa 18 000 18 000 18 000
Tensile strength EN ISO 527-2 Mpa
Susceptibility to cracking EN 438-2, point 24
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % 0,15 * *
cross. % 0,25 * *
Resistance to boiling water EN 438-2, point 12 % 0,3 * *
Coefficient of thermal expansion
DIN 52328 1/K
Thermal conductivity W/mK
Resistance to vapour diffusion
μ 730 000
Surface resistance DIN 53482 Ohm
Resistance to cigarette burns
EN 438-2, point 30 Degree 5 - no visible changes2) 5 - no visible changes2) 5 - no visible changes2)
Resistance to hot soucepans
EN 438-2, point 16 Degree 5 - no visible changes, no blisters or cracks3)
5 - no visible changes, no blisters or cracks3)
5 - no visible changes, no blisters or cracks3)
Heating value MJ/kg
Optical properties
Light fastness EN 438-2, point 27 Level 6-8 6-8 6-8
1) Properties for Alucompact 3 Mark are similar to those of the Alucompact 42) Slight change in glossy finish, yellow or light brown colours are permitted by EN 4383) Slight change in glossy finish permitted by EN 438* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture.
(Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. ALUCOM Rev. 1 del 10/05/2012
reAction to fire clAssificAtion
Standard Class 2
Europe EN 13501-1 Euroclass D-s2, d0
Austria A3800/1 Tr1, Q1
Germany DIN 4102 B2
AlucompactTechnical Data and Certifications
Mod. COCORE Rev. 1 del 10/05/2012
Compact CoreTechnical Data and Certifications
Material properties tested in aCCordanCe to en 438-2 (average value of production control)
Properties Norms Unit Value
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 1,55
Thickness (e.g.) EN 438-2, point 5 mm 10
Weight kg/m2 15,5
Mechanical properties
Resistance against stress abrasion EN 438-2, point 10 U 450
Falling ball impact resistance EN 438-2, point 21 mm
Resistance against scratching EN 438-2, point 25 Degree 3
Scratch r. 4N
Flexural strength EN ISO 178 Mpa 80
E-Modulus EN ISO 178 Mpa 9000
Tensile strength EN ISO 527-2 Mpa 60
Susceptibility to cracking EN 438-2, point 24 4
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % ≤ 0,5
cross. % ≤ 0,8
Resistance to boiling water EN 438-2, point 12 %
Coefficient of thermal expansion DIN 52328 1/K
Thermal conductivity W/mK
Resistance to vapour diffusion μ
Surface resistance DIN 53482 Ohm
Resistance to cigarette burns EN 438-2, point 30 Degree 5
Resistance to hot soucepans EN 438-2, point 16 Degree 5
Heating value MJ/kg
Optical properties
Light fastness EN 438-2, point 27 Level 6-8
* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture. (Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. COCORE Rev. 1 del 10/05/2012
reaCtion to fire ClassifiCation
Standard Class 2
Europe EN 13501-1 Euroclass D-s2, d0
Austria A3800/1 Tr1, Q1
Germany DIN 4102 B2
Compact CoreTechnical Data and Certifications
Mod. COWOOD Rev. 1 del 10/05/2012
Compact Wood®
Technical Data and Certifications
Material properties tested in aCCordanCe to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 ≥ 1,4
Thickness (e.g.) EN 438-2, point 5 mm 10
Weight kg/m2 14,0
Mechanical properties
Resistance against stress abrasion EN 438-2, point 10 U 450
Falling ball impact resistance EN 438-2, point 21 mm 8
Resistance against scratching EN 438-2, point 25 Degree 3
Scratch r. 4N
Flexural strength EN ISO 178 Mpa 100
E-Modulus EN ISO 178 Mpa 10 000
Tensile strength EN ISO 527-2 Mpa 60
Susceptibility to cracking EN 438-2, point 24 5
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % 0,05
cross. % 0,15
Resistance to boiling water EN 438-2, point 12 % 0,3
Coefficient of thermal expansion DIN 52328 1/K 20 × 10-6
Thermal conductivity W/mK ca. 0,3
Resistance to vapour diffusion μ 17 200
Surface resistance DIN 53482 Ohm 109-1011
Resistance to hot soucepans EN 438-2, point 16 Degree 5 - no visible changes, no blisters or cracks1)
Heating value MJ/kg 18-20
Optical properties
Light fastness EN 438-2, point 27 Level 6-8
1) Slight change in glossy finish permitted by EN 438* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture.
(Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. COPAIN Rev. 1 del 10/05/2012
Compact Paint®
Technical Data and Certifications
Material ProPerties tested in aCCordanCe to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density DIN 52350/ISO 1183 g/cm3 ≥ 1,4
Thickness (e.g.) EN 438-2, point 5 mm 10
Weight kg/m2 14,0
Mechanical properties
Resistance against stress abrasion EN 438-2, point 10 U 450
Falling ball impact resistance EN 438-2, point 21 mm 8
Resistance against scratching EN 438-2, point 25 Degree 3
Scratch r. 4N
Flexural strength EN ISO 178 Mpa 100
E-Modulus EN ISO 178 Mpa 10 000
Tensile strength EN ISO 527-2 Mpa 60
Susceptibility to cracking EN 438-2, point 24 5
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17 lenght. % 0,05
cross. % 0,15
Resistance to boiling water EN 438-2, point 12 % 0,3
Coefficient of thermal expansion DIN 52328 1/K 20 × 10-6
Thermal conductivity W/mK ca. 0,3
Resistance to vapour diffusion μ 17 200
Surface resistance DIN 53482 Ohm 109-1011
Resistance to hot soucepans EN 438-2, point 16 Degree 5 - no visible changes, no blisters or cracks1)
Heating value MJ/kg 18-20
Optical properties
Light fastness EN 438-2, point 27 Level 6-8
1) Slight change in glossy finish permitted by EN 438* These qualities are only suitable for inner lining. The panels should not be exposed to high fluctuations of temperature or moisture.
(Recommended range: +15 - +35°C, 30 -70% rel. to air moisture)
Mod. CO2002 Rev. 1 del 10/05/2012
Compact 2002Technical Data and Certifications
Material properties tested in aCCordanCe to en 438-2 (average value of production control) - Classification CGS
Properties Norms Unit Value
Physical data
Apparent density EN ISO 1183 g/cm3 ≥ 1,35
Thickness tolerance EN 438-2, point 5 mm 5,0 ≤ t < 8,0 ± 0,40
8,0 ≤ t < 12,0 ± 0,50
12,0 ≤ t < 16,0 ± 0,60
16,0 ≤ t < 20,0 ± 0,70
Mechanical properties
Resistance against stress abrasion (wear value) EN 438-2, point 10 Revolutions ≥ 350
Falling ball impact resistance
Indentation diameter - 2 ≤ t < 6 mm with 1.4 m drop height
EN 438-2, point 21 mmh 1400 / d ≤ 10
Indentation diameter - 6 ≤ t < mm with 1.8 m drop height
h 1800 / d ≤ 10
Resistance against scratching EN 438-2, point 25 Rating ≥ 2 smooth finishes and ≥ 3 textured finishes
Flexural strength EN ISO 178 Mpa ≥ 80
E-Modulus EN ISO 178 Mpa ≥ 9000
Susceptibility to cracking EN 438-2, point 24 Rating ≥ 4
Thermal properties
Dimensional changes during climatic changes, measured at elevated temperatures
EN 438-2, point 17long. %
2 ≤ t < 5 mm1) ≤ 0,40
5 ≤ t < mm1) ≤ 0,30
trasv. %2 ≤ t < 5 mm1) ≤ 0,80
5 ≤ t < mm1) ≤ 0,60
Resistance to boiling water (thickness increase) EN 438-2, point 12 % 2 ≤ t < 5 mm ≤ 6
5 ≤ t mm ≤ 2
Thermal conductivity EN 12664 W/mK 0,2 to 0,5
Resistance to water vapour EN 438-2, point 14 Rating ≥ 3 gloss finishes and ≥ 4 other finishes
Resistance to cigarette burns EN 438-2, point 30 Rating ≥ 3
Resistance to dry heat (180°C/ 20 min.) EN 438-2, point 16 Rating ≥ 3 gloss finishes and ≥ 4 other finishes
Optical properties
Light fastness EN 438-2, point 27 Grayscale ≥ 4
1) Cumulative dimensional changes
Mod. CO2002 Rev. 1 del 10/05/2012
Food ContaCt
Properties Norms Unit Value
Overall migration EN 1186-3 mg/dm2 3% acetic acid 24 at 40°C < 10
EN 1186-3 50% ethanol 24 at 40°C < 10
EN 1186-14 95% ethanol 24 at 40°C < 10
EN 1186-14 isooctane 24 at 40°C < 10
Formaldehyde specific migration EN 13130-23 mg/kg 3% acetic acid 24 at 40°C < 15
reaCtion to Fire ClassiFiCation
Properties Norms Unit Value
Reaction to fire CGS and ACS types
EN 13501 Class 2 mm ≤ t < 6 mm D-s1,d0 (metal frame)
t ≥ 6 mm C-s1,d0 (metal frame)
t ≥ 2,5 mm D-s2,d0 (wood frame)
Reaction to fire CGF and ACF types
EN 13501 Class t ≥ 2,5 mm B-s1,d0 (metal frame)
3 mm ≤ t < 6 mm C-s2,d0 (metal frame and wood frame)
t ≥ 6 mm B-s1,d0 (metal frame and wood frame)
Compact 2002Technical Data and Certifications