complete solar thermal residential systems · high performance, solar collectors with factory...
TRANSCRIPT
Solar Thermal Has Never Been Easier!
High Performance, solar collectors with factory installed unions and sensor wells
Solderless Connections make installs “no sweat”
Overheat Protection provided by drainback design
Lightweight, 316L Stainless Steel Tanks (Industry Best Warranties)
Complete Solar Thermal Residential Systems
Advanced Heating &Hot Water Systems
w w w.htproduc ts.com
Solderless Connections make installs “no sweat”
Complete Solderless Systems• All connections simply screw together• Supply and Return lines are pre-insulated, flexible stainless steel• Highly efficient solar pump has union fittings to connect directly to tank and flex line.• Systems available in both drainback or pressurized with gas or electric backup
Collector Return Hot Out
Collector Feed
Cold In
Top Heat Exchanger Connection
Male Half Union Cap
Female Half Union Cap
Factory Installed Unions
Drainback TankConnections
Drainback Tank Gauge & PRV
Tank Sensor
Collector Sensor
Bottom HX port Connection with pump assembly to insulate SST
Drainback Systems
Pressurized Systems
What is a Drainback System?• Drainback Systems offer the ultimate in both
overheat and freeze protection
• Drainback Systems are perfect for hot
and cold climates
• The collectors are normally dry until the
system calls for heat and turn on the pump
to harvest the energy, when the system is
satisfied, then the pump shuts off and the
fluid drains by gravity back to the drainback tank
• Drainback Systems require only water for the
solar fluid with is readily available and provides
the greater heat transfer over glycol
• Drainback Systems are the easiest to install and
require the least maintenance
What is a Pressurized System?• Pressurized Systems are used in situations where
achieving slope back to the drainback tank is not
possible.
• Pressurized Systems and the solar collectors are
filled with propylene glycol as the solar fluid day
and night, summer and winter
• Pressurized Systems require an expansion tank
and a pressure relief valve
• Pressurized Systems require more attention on an
annual basis making sure the glycol is adequate
for the climate
• Pressurized Systems rely many components
for overheat protection from the differential
controller to expansion tanks to pressure
relief valves
Drainback with Gas Backup
Pressurized with Gas Backup
Drainback with Electric Backup
Pressurized with Electric Backup
HTP's Exciting New Solar Tanks
Solar Tank with a Up to 97% High Efficiency Gas Fired Back-up• Reduce Your Water Heating Bills by 50% to 75%• Federal Solar Tax Credits• Utility Rebates & State Incentives• Energy Compliance Credits and Fuel Savings• Long Lasting 316L Stainless Steel Tank• No Anode Rods Needed• Super Insulated!• Extremely Durable 316L Stainless Steel Solar Heat Exchanger• Space Heating with Auxiliary Port• 76,000 Btuh Modulating Burner with Up to 3 to 1 Turndown Ratio• 10 Year Limited Warranty
Solar Electric with an Indirect Back-up• Reduce Your Water Heating Bills by 50% to 75%• Federal Solar Tax Credits• Utility Rebates & State Incentives• Energy Compliance Credits and Fuel Savings• Long Lasting 316L Stainless Steel Tank• No Anode Rods Needed• Super Insulated!• Extremely Durable 316L Stainless Steel Solar Heat Exchanger• 10 Year Limited Warranty
Phoenix LD-S
SSP 80 SE
Laser W elding
Laser welding of the absorber sheet to the absorber tubes ensures a very high mechani-cal bond to withstand the high temperature gradients and thermal expansion
Laser welding also provides enhanced performance and aesthetics
Solar Skies SS-FP Series CollectorsCorner BracketsArchitectural aluminum angles inside with special pin grip rivets insure high stability.
Glass Gasket...a UV durable EPDM channel with molded corners assures long life and avoids all water penetration.
Aluminum Extruded BattenNo silicon is used! Ribbed aluminum extrusions and a smooth compressed EPDM gasket provide water tightness. This allows easy access to the collector for repair or maintenance at any time or location.
Lightweight Aluminum Frame ...this facilitates long life and strength.
Universal Mounting FrameThe variable Quick Lock mounting hardware reduces mounting time and makes it simple for anyone to install. Mounting possibilities include: Pitched-roof, Flatroof, Ground, Balcony, and Facade mounting.
Highest Absorptive Coating in the IndustryVapor Deposition Coatingα≈ 95%ε ≈ 5%
Full Sheet Aluminum Absorber
Factory Installed Unions
Foil-Faced Poly-Isocyanurate Insulation Sheathing
Embossed Aluminum Backsheet
Laser Welding
Copper Absorber Tubes
HTP Made In Am
erica • HTP Made In A
mer
ic
a • HTP Made In A
merica • HTP Made In
Am
eric
a •
Technical Specifications & FeaturesPerformance Specifications Series Specifications
272 Duchaine Blvd, New Bedford, MA 02745
w w w. h t p r o d u c t s . c o m
MKTLIT-XX – 02/2016 © HTP
Flat Plate Collectors
SS-40-FP 4' x 10' Flat plate collector - 121. 25” x 47. 25” / 153 lbs.
SS-32-FP 4' x 8' Flat plate collector - 97. 25” x 47. 25” / 113 lbs.
SS-26-FP 4' x 6.5' Flat plate collector - 77. 25” x 47. 25” / 90 lbs.
Mounting Hardware for Flat Plate Panels
MT-TM Tilt mount set per panel (often used with rear leg 1"x1" strut)
MT- FM Flush mount set per panel
MT- R M Rack mount set per panel
E I 0 2 2 Rear leg strut 1" X 1" square tube per foot (use with standard mount kit)
Solar Skies (model) - Size (ft²) - FP (full plate) -U (factory installed unions): factory installed union collectors must purchase an A505 cap, plug and union kit for each plumbing collector array installed. An array is any number of collectors unioned together (up to 8)
SS-40-FP
Thousands of Btus per panel per day
Weather-Categor y( Ti-Ta)*
Clear Day2000 Btu/
ft²- d
Mildly Cloudy
1500 Btu/ft²- d
Cloudy Day1000 Btu/
f t ²- d
A (–9°F) 46.1 34.8 23.5B (9°F) 44.0 32.7 21.4
C (36°F) 40.6 29.3 18.0 D (90°F) 34.2 23.0 11.8 E (144°F) 27.1 16.8 6.2
Information on Models: SS-26-FP, SS-32-FP & SS-40-FP is available on our website: www.htproducts.com
“QUICK LOCK” MOUNTING FRAMEThe variable Quick Lock mounting hardware reduces mounting time and makes it simple for anyone to install. The Quick Lock System
allows the highest flexibility in mounting and can withstand extreme conditions. Mounting possibilities include: Pitched-roof,
Flat-roof, Ground, Balcony, and Facade mounting.
MT-RM Rack Mount(4 PER KIT)
MT-FM Flush Mount(4 PER KIT)
MT-TM Tilt Mount(2 FRONT, 2 REAR PER KIT)*
(*strut not included)
FRONT
REAR
SS Series Mounting Hardware
Collector SS-26 SS-32 SS-40
Base Dimension 78 98 122
SS SeriesTilt Mount
DETAIL A
DETAIL C
DETAIL B
B
A C
Base Dimension
Advanced Heating andHot Water Systems