contractor mini heavy duty flail mowers for small & high ......contractor mini heavy duty flail...
TRANSCRIPT
Ryetec Industrial Equipment Limited
Mill House, A64 East Knapton, Malton, N Yorks, YO17 8JA,
Tel: 01944 728186 www.ryetec.co.uk Email: [email protected]
Contractor Mini Heavy Duty Flail Mowers
for Small & High Powered Compact Tractors
CM180
Designed for heavy duty mowing operations
Cuts long wet grass effectively
Heavy hammer flails cut material up to 50mm (2”)
in diameter and a straight cutting edge gives
excellent finish
Hydraulic offset (optional on standard machines)
gives good manoeuvrability around obstacles
Quiet in operation
Even spread of grass cuttings
Low profile design, allows for work up to hedge
rows and fence lines with minimum risk of damage
Large range with two build types
Standard build ‘CM’
• Cutting widths from 0.95 to 1.75m
• Heavy duty hammer flails with back to back
grass flail option (for lower power requirement)
• Full width, height adjustable rear roller and skids
• Overrun clutch on PTO
• Cat 1 manual offset linkage (hydraulic option)
• Rubber stone guards
Heavier ‘S’ build ‘CMS’ • Cutting widths from 1.15 to 2.15m
• Heavy duty hammer flails with back to back
grass flail option (for lower power requirement)
• Full width, height adjustable rear roller and skids
• Heavy duty gearbox with overrun clutch
• Double skin with internal mulching teeth
• Cat 1/2 3 point hitch
• Hydraulic offset linkage
• Steel stone guards
Fixed and floating positions for linkage mounting
allow the machine to follow ground contours
Heavy duty gearbox with solid oil immersed output
shaft
Remote greasers on rotor bearings
Easily viewed by operator
Front or rear mounting The Contractor Mini range has been designed for
maximum flexibility and is available in front or rear
mounting on all standard build CM models. Optional
special factory build with dual linkage and gearbox allows
CMS models from 1.6m upwards to be front mounted.
CM200S
CMS effectively reducing heavy growth with
standard internal mulching teeth
Ryetec Industrial Equipment Limited
Mill House, A64 East Knapton, Malton, N Yorks, YO17 8JA
Tel: 01944 728186 www.ryetec.co.uk Email: [email protected]
Specifications
Standard specification includes skids and 540rpm PTO speed on all models
Tractors must be fitted with a double acting spool valve to operate hydraulic offset linkage
Model Working
width
mm
Weight
kg
No. of
hammer
flails
Min
tractor
hp
Front
mounting
Double
skin
Hydraulic
offset
Sta
nd
ard
CM100 950 165 12 15 - 25 T X O
CM130 1250 200 16 15 - 30 T X O
CM150 1450 215 18 25 - 40 T X O
CM180 1750 240 22 25 - 40 T X O
Su
per ‘S
’ mo
dels
CM120S 1150 355 10 20 - 60 X T T
CM140S 1350 390 14 25 - 60 X T T
CM150S 1450 390 14 25 - 60 X T T
CM160S 1550 410 14 30 - 60 O T T
CM180S 1750 430 16 35 - 60 O T T
CM200S 1950 470 18 35 - 60 O T T
CM220S 2150 490 20 40 - 60 O T T
Flails
The Contractor Mini flail hammer can cut any material up to 2” (50mm in diameter) and its straight cutting edge
leaves a perfect finish. The flail is easily sharpened in situ to extend its working life.
CM standard build
machines
XF166011
Heavy hammer flail
CMS heavy build
machines
X75700001
Heavy hammer flail
All machines
benefit from an
offset linkage
of 300mm. This
is hydraulic on
CMS models
and manual
with hydraulic
option on CM
machines.
= Standard O = Optional X = Not available