control valves globe 3-way, diverting & mixing type...the valve body may be very cold or very...
TRANSCRIPT
Control ValvesGlobe 3-way, Diverting & Mixing type Series GW
Installation, Maintenance andOperating Instructions
4 GV
74 en • 5/2018
2 4 GV 74 en
READ THESE INSTRUCTIONS FIRST!These instructions provide information about safe handling and operation of the valve.If you require additional assistance, please contact the manufacturer or manufacturer's representative.Addresses and phone numbers are printed on the back cover.See also www.metso.com/valves for the latest documentation.SAVE THESE INSTRUCTIONS!
Subject to change without notice.All trademarks are property of their respective owners.
Table of Contents1 GENERAL...............................................................3
1.1 Scope of the manual ............................................31.2 Valve construction ................................................31.3 Valve markings .......................................................31.4 Technical specifications ......................................41.5 Valve seat leakage class ......................................41.6 Recycling and disposal ........................................41.7 Safety precautions ..............................................4
2 TRANSPORTATION, RECEPTION AND STORAGE...............................................................4
3 VALVE INSTALLATION .........................................53.1 General ......................................................................53.2 Installation into the pipeline .............................53.3 Control valve assembly .......................................53.4 Valve insulation......................................................5
4 MAINTENANCE ....................................................64.1 General ......................................................................64.2 Gland packing adjustment.................................64.3 Replacing the gland packing ..........................64.4 Replacing the trim and body reassembly ....7
5 TESTING THE VALVE ............................................76 REMOVAL & MOUNTING THE ACTUATOR ..........87 TOOLS ...................................................................98 ORDERING SPARE PARTS ....................................99 EXPLODED VIEW AND PARTS LIST ...................1010 DIMENSIONS AND WEIGHTS .............................11
10.1 Valve GW................................................................ 1110.2 Actuators VD, VC................................................. 12
11 Actuator dimensions .........................................1411.1 VC cylinder actuators without
handwheel ............................................................ 1411.2 VC cylinder actuators with handwheel....... 15
12 TYPE CODE .........................................................16
This product meets the requirements set by the Customs Union of the Republic of Belarus,
the Republic of Kazakhstan and the Russian Federation.4 GV 74 en 3
1 GENERAL
1.1 Scope of the manualThis manual provides essential information on series GW,Globe 3-way Diverting or Mixing type installed sliding stemvalves. Actuators and positioners are only discussed briefly.Refer to the individual manuals for further information ontheir installation, operation and maintenance.
1.2 Valve constructionSeries GW valves are flanged (weld end available) 3-waysliding stem control valves. Two seat rings and the plugwith stem is a module accessible through the bottom bon-net opening (bottom entry) of the body. GW valves are available both diverting and mixing flow fora most primary application is in temperature control.Our standard design combines the benefits of more strongguiding with a top and bottom seat rings, and the solid cylin-drical plug makes strong support to ensure valve alignment.GW valves are available both cylindrical and V-port plug trimdepending from the application, standard is cylindrical plug.This series are available to provide a series of reduced trimand the standard seat tightness is class II, optional trims canmeet to class III and IV, ANSI/FCI 70.2.The detailed structure is revealed by the type code shownon the valve identification plate. The type code is explainedin Section 11.
1.3 Valve markingsThe body markings are: manufacturer's trademark, nominalsize, pressure rating and material of the body. The valve hasan identification plate attached to it, see Fig. 2.
Markings on the identification plate:1. Type designation (Valve code)2. Size, Rating 3. Cv4. Body material 5. Plug, Stem material6. Seat material 7. Temp. min./max.8. Maximum (shut-off ) pressure 9. Valve manufacturing date10. Tag No.11. Serial No.
NOTE:Selection and use of the valve in a specific applicationrequires close consideration of detailed aspects. Due to thenature of the product, this manual cannot cover all the indi-vidual situations that may occur when the valve is used.If you are uncertain about use of the valve or its suitabilityfor your intended purpose, please contact Metso for moreinformation.For valves in oxygen service, please see also the separateinstallation, maintenance and operating instructions foroxygen service (see Metso document id:10O270EN.pdf).
Fig. 1 Construction of the Neles GW series 3-way Valve
Mixing type Diverting type
Fig. 2 Identification(name) plate example
TYPE
B ODY
S TE M
S E AT
P LUG
DATE
t max.
S IZE
M. A. W. P
TAG No.
0496
235 C heomdansaneop 1-ro, Daesowon-myeon,C hungju-s i, C hungche ongbuk-do, K oreaMetso Flow C ontrol
F LUID G R OUP
t min.
C O No.
R ATING
C v
4 4 GV 74 en
1.4 Technical specificationsFace-to-face length: ANSI/ISA-75.08.01, 03, 05 &
ANSI/ISA-75.08.06 (Long)
Body rating: Class 150 to Class 600
PN 10 to PN 40
Max. pressure differential:acc. to pressure class
Temperature range: -29° to +270 °C
Flow direction: indicated by an arrow on the body
Actuator mounting: threaded bonnet with yoke nut orbolted yoke
Stem connection: clamp with bolts/nuts
Dimensions: see Section 10
Weights: see Section 10
Note that the max. shut-off pressure is based on the mechan-ical maximum differential pressure at ambient temperature.You must always observe the fluid temperature when decid-ing on applicable pressure values. When selecting a valveyou must also check the noise level, cavitation intensity, flowvelocity, actuator load factor, etc. using Nelprof.
1.5 Valve seat leakage class The valve follows the seat leakage classifications of ANSI/FCI 70-2 requirement.
1.6 Recycling and disposalMost valve parts can be recycled if sorted according to material. Most parts have a material marking. A material list is supplied with the valve. In addition, separate recycling and disposal instructions are available from the manufactu-rer. A valve can also be returned to the manufacturer for recycling and disposal for a fee.
1.7 Safety precautions
2 TRANSPORTATION, RECEPTION AND STORAGE
Check the valve and the accompanying devices for anydamage that may have occurred during transport.Store the valve carefully before installation, preferablyindoors in a dry place.
CAUTION:Do not exceed the valve performance limitations!Exceeding the limitations marked on the valve may causedamage and lead to uncontrolled pressure release. Dam-age or personal injury may result.
CAUTION:Do not dismantle the valve or remove it from the pipe-line while the valve is pressurised!Dismantling or removing a pressurised valve will result inuncontrolled pressure release. Always isolate the relevantpart of the pipeline, release the pressure from the valveand remove the medium before dismantling the valve.Be aware of the type of medium involved. Protect yourselfand the environment from any harmful or poisonous sub-stances. Make sure that no medium can enter the pipelineduring valve maintenance.Failure to do this may result in damage or personal injury.
CAUTION:Beware of the plug movement!Keep fingers, other parts of the body, tools and otherobjects out of the open flow port. Leave no foreign objectsinside the pipeline. When the valve is actuated, the plugfunctions as a cutting device. Close and detach the actuatorpressure supply pipeline for valve maintenance. Failure todo this may result in damage or personal injury.
CAUTION:Protect yourself from noise!The valve may produce noise in the pipeline. The noiselevel depends on the application. It can be measured orcalculated using the Metso Nelprof software. Observe therelevant working environment regulations in terms ofnoise emission.
CAUTION:Beware of a very cold or hot valve!The valve body may be very cold or very hot during use.Protect yourself against cold injuries or burns.
CAUTION:When handling the valve or the control valve assem-bly, take its weight into account!Never lift the valve or control valve assembly by the posi-tioner, the limit switch or their piping.Place the lifting ropes securely around the valve body (seeFig. 3). Damage or personal injury may result from fallingparts.
CAUTION:Follow the proper procedures when handling and ser-vicing Oxygen valves.
Fig. 3 Lifting the valve
321
4
1 2 3
4
4 GV 74 en 5
Do not remove the flow port protectors until immediatelybefore installation of the valve into the pipeline.The valve is delivered in the closed position. A valveequipped with a spring-return actuator is delivered in theposition determined by the spring.
3 VALVE INSTALLATION
3.1 GeneralRemove the flow port protectors and check that the valve isclean inside.
3.2 Installation into the pipeline
3.2.1 Pipeline cleaning Make sure no foreign particles, such as sand or pieces ofwelding electrode, are in the pipeline, they may damagethe sealing surfaces.
3.2.2 Installation valveThe valve has an arrow indicating the flow direction. Installthe valve in the pipeline so that the flow direction of thevalve corresponds to the flow direction marked on the pipe.The mounting orientation of the valve should be verticalposition as it is shown on Fig.4.
Choose flange gaskets according to the operatingconditions.Do not attempt to correct a pipeline misalignment bymeans of flange bolting.Loads on the valve body from pipeline vibrations can bereduced by supporting the pipeline properly. Reducedvibration also increases the lifetime of the positioner.Where necessary, you can support the valve by the body,using regular pipe clamps and supports. Do not fasten sup-ports to the valve or flange bolting or to the actuator, seeFig. 4.
3.2.3 Hydrostatic testing and Line flushingWhen the line is hydrostatic test and flushing, the controlvalve should not used as an isolating valve.Make sure the control valve always be opened positionbefore start this process.Otherwise valve and trim damage or failure of the sealscould result.Flushing and hydrostatic test kit can be purchased fromMetso.
3.3 Control valve assemblyCheck all joints, piping and cables.Check that the actuator stop screws, positioner and limitswitches are calibrated. Refer to their installation, mainte-nance and operating manuals.
3.4 Valve insulationIf necessary, the valve may be insulated. Insulation must notcontinue above the upper level of the valve body, see Fig. 5.
CAUTION:When handling the valve or the control valve assem-bly, take its weight into account!
NOTE:Over 260'C, a heat-insulation should be installed, howeverdon't insulate the cryogenic nor extension bonnet relativeto personal safety.
NOTE:For any other mounting position, please consult thefactory.
CAUTION:Flushing trim kit sholud be installed in the valve (espe-cially 'Tendril' application) to protect the original trim andthe flow passages while the valve installation and lineflushing.Unless this caution could result in clogging trim, low flowrates, unstable control, valve leakage and exessive noiseand other trouble.
Fig. 4 Installing the control valve into pipeline usingsupports
Fig. 5 Insulation of the valve
MATERIAL
HEAT NO.
SIZE-RATING
Insulation limit
6 4 GV 74 en
4 MAINTENANCE
4.1 GeneralThe Neles series GW 3-way valves require no regular main-tenance. However, check the gland packing for leakage.This section outlines the maintenance that can be carriedout by the user.The numbers in parentheses refer to the parts lists and theexploded views of the valve in Section 9.
4.2 Gland packing adjustmentIn the event of a packing leakage tighten the hexagon nuts(18) in ¼ turn steps each until the leakage is stopped. Donot tighten more than necessary.
4.3 Replacing the gland packing
Make sure the valve is not pressurised. Remove the actuator from the valve stem according
to the instructions given in the actuator manual. Loosen and remove the hexagon nuts (18). Remove the gland flange (9b), and gland (9a) up to
the valve stem. Remove the old packing rings (69) using a pointed tool,
avoid damaging the seal surfaces and valve stem.
Clean the packing ring counterbore. Mount the new packing rings one by one into the
packing gland box using the gland as a tool andmount the gland with hand-tightened nuts.
Fasten the gland with the hexagon nuts (18) andtighten them.
Check leakage when the valve is pressurised.
Table 1 Required torques for bonnet nuts
Table 2 Required torques for packing nuts
CAUTION:Observe the safety precautions listed in Section 1.7before starting work!
CAUTION:When handling the valve or the control valve assem-bly, take its weight into account!
NOTE:If you send the valve to the manufacturer for repair, do notdismantle it. Clean the valve carefully, including the inside.For safety reasons, inform the manufacturer of the natureof the medium when you send the valve.
NOTE:Always use original spare parts to make sure the valvefunctions as intended.
CAUTION:Do not dismantle the valve or remove it from the pipe-line while the valve is pressurised.
Fig. 6 Gland packing
Mold Packing Application V-Packing Application
Valve Size Ratin(ANSI)
Bonnet Stud Bolts Required Torques (±5% allowable)
mm in Size Q'ty Nm lbf ft
25 1 150-300 1/2"-13UNC 4 45 33600 1/2"-13UNC 4 45 33
40 1.5 150-300 1/2"-13UNC 4 45 33600 1/2"-13UNC 4 45 33
50 2 150-300 1/2"-13UNC 8 45 33600 1/2"-13UNC 8 45 33
80 3 150-300 5/8"-11UNC 8 90 66600 5/8"-11UNC 8 90 66
100 4 150-300 3/4"-10UNC 8 160 118600 3/4"-10UNC 8 160 118
150 6 150-300 3/4"-10UNC 12 160 118600 3/4"-10UNC 12 160 118
200 8 150-300 7/8"-9UNC 12 250 184600 7/8"-9UNC 12 250 184
250 10 150-300 1"-8UNC 16 380 280600 1"-8UNC 16 380 280
Fig. 7 Tightening sequence of the bonnet nuts
Packing Type
Stem Size Rating(ANSI)
Required Torques
mm Min. Nm(lbf ft)
Max. Nm(lbf ft)
Graphite &PTFE
Carbon Fiber packing
Ø12.7
150-300 5 (4) 7 (5)600 6 (4) 8 (6)900 7 (5) 10 (7)
1500 9 (7) 12 (9)2500 10 (7) 14 (10)
Ø19.05
150-300 11 (8) 16 (12)600 14 (10) 19 (14)900 17 (12) 23 (17)
1500 19 (14) 27 (20)2500 22 (16) 21 (15)
Ø25.4
150-300 18 (13) 25 (18)600 23 (17) 32 (24)900 27 (20) 38 (28)
1500 32 (24) 44 (32)2500 36 (27) 51 (38)
Ø36
150-300 26 (19) 36 (27)600 32 (24) 45 (33)900 39 (29) 54 (40)
1500 45 (33) 64 (47)2500 52 (38) 73 (54)
V-ring packing (PTFE)
Ø12.7
150-300 3 (2) 5 (4)600 4 (3) 6 (4)900 5 (4) 7 (5)
1500 6 (4) 8 (5)2500 7 (5) 10 (7)
Ø19.05
150-300 8 (6) 11 (8)600 10 (7) 14 (10)900 12 (9) 16 (12)
1500 14 (10) 19 (14)2500 16 (12) 22 (16)
Ø25.4
150-300 13 (10) 18 (13)600 16 (12) 22 (16)900 19 (14) 27 (20)
1500 22 (16) 31 (23)2500 25 (18) 35 (26)
Ø36
150-300 18 (13) 25 (18)600 23 (17) 32 (24)900 27 (20) 38 (28)
1500 32 (24) 44 (32)2500 36 (27) 51 (38)
4 GV 74 en 7
4.4 Replacing the trim and body reassembly
Make sure the valve is not pressurised. Remove the actuator from the valve stem according
to the instructions given in the actuator manual andnext Section 6.
Turn the body (1) and remove the bottom hexagonnuts (17).
Remove the bottom flange (26). Remove the body gasket (65). Remove the stem (5) and plug (3) sub-assembly.
Avoid from damaging the seating and guiding lineof the plug.
Remove the each two seat rings (7 & 7a) from body(1) and bottom flange (26) using by fabricatedwrenches to be engaged the seat ring lugs andadapted to shock wrench.This is threaded type, if the seat ring is extremelyresistance to removal, the application of heat or pen-etrating oil will be helpful.
Remove the hexagon nuts (18), gland flange (9b)and packing gland (9a) from the bonnet (8).
Remove the old packing rings (69). Clean the body gasket surface. Insert and tighten the each new top and bottom seat
rings (7 & 7a) into the body (1) and bottom flange(26).
Insert the stem (5) & plug (3) sub-assembly from topside into the body very carefully.
Insert the body gasket (65) into bottom side of thebody.
Mount the bottom flange (26) on the body carefullymaintaining alignment with the plug and stem inthe closed position, so that the bonnet position inrelation to the body is the same as the original posi-tion.
Insert the hexagon nuts (17) into stud (13) andslightly fasten the nuts.
Insert the packing rings (69) according to above 4.3
Tighten hexagon nuts (17) until plug and seat con-tact is obtained with proper bolt torque.
5 TESTING THE VALVE
We recommend that the valve body is pressure-tested afterthe valve has been assembled.The pressure test should be carried out in accordance withan applicable standard for the pressure rating. The valvemust be in the open position during the test.
NOTE:The trim set consists of the seat rings, valve plug and stem,gaskets (for body).
CAUTION:If using heating devices, insure that proper safetypractices are observed. Such items as the flammabilityand toxicity of the controlled substance must be consi-dered and proper precautions and permissions taken.
CAUTION:Do not strongly tighten hexagon nuts (17) at this time.
CAUTION:Do not reuse the spiral wound gaskets (65), this isneed to be replace each time the valve is disassemb-led.
CAUTION:The all related parts (seat ring, plug & stem, bonnet)must be properly aligned in the body.
Fig. 8 Conventional Cylindrical Plug Trim
NOTE:If the valve have excess leakage, the plug and seating sur-face need lapping and cleaning.
CAUTION:Pressure testing should be carried out using equip-ment conforming to the correct pressure class!
Fig. 9 Trim design
11
9b
18
14
8
5a
3
1
9a
69
21
67
7
65
17
13
26
7a
17a
5
2
GW series, Cylindrical plug trim
Trim design
8 4 GV 74 en
6 REMOVAL & MOUNTING THE ACTUATOR
The actuator is attached to the valve according to the manualfor actuator with body assembly and plug stem adjustment .Several types of Metso actuators can be used with suitableclamps. Refer to the model VD spring-diaphragm and VCdouble acting cylinder actuator manuals for further informa-tion on their installation, maintenance and operation.
A. Actuator removal for Reverse <air to top seat close,stem retract> actuator (Fig. 10) Lift up to the valve plug 100% from the seat ring,
using by specified air pressure. Loosen the stem lock nut (5**) and socket socket
head screws (1a**) and hexagon nuts (1b**). Remove the clamp (1**). Shut off and disconnect air supply line. Support actuator with the suitable lifting device. Remove the yoke nut (3**). Remove the actuator from the valve body assembly.
B. Actuator replacement (mounting) for Reverse <air totop seat close, stem retract> actuator (Fig. 10) Mount the new or repaired actuator on top of the
bonnet, using a suitable lifting device. Insert the yoke nut and tightly fasten the yoke by
turning the yoke nut (3**) clockwise using tighten-ing tools.
Connect air line and accessories. Lift the top stem (18), using by specified air pressure. Adjustment stem length after clamping the
clamp (1**) according to rated travel(stroke) as‘open’ and ‘close’ position as per pressurizing anddepressurizing the lower diaphragm chamber.
Tighten stem socket head screws (1a**) and hexa-gon nuts (1b**) with stem lock nut (5**).
Standard valve construction
With the handwheel or pneumatically, push thevalve stem and plug to be slightly touched with seatring to make sure if valve is fully closed.
With the handwheel or pneumatically, stroke theactuator to the fully open.
Measure the maximum distance between the valvestem and actuator top stem.
Calculate the gap (measured value – rated travel =gap 1).
Move down the top stem so that the distancebetween the valve stem and actuator top stemshould be gap 1.
Fit the clamp to align with both stems thread. Line up the stroke indicator with the clamp indicator
arrow and check actuator for operation. Tighten the socket head screws after adjusted the
rated stroke.
Pilot valve construction
With the handwheel or pneumatically, push thevalve stem and plug to be slightly touched with seatring to make sure if valve is fully closed. And markthe valve stem end location by a line on the yoke ortravel indicator.
And move up the top stem. And mark the valve stemend location by a line on the yoke or travel indicatorafter valve stem is moved by a spring inside pilotplug.
Measure the distance between two lines, which isgap 2.
Stroke the actuator to the fully open. Measure the maximum distance between the valve
stem and actuator top stem. Calculate the gap (measured value – rated travel –
gap 2 = gap 3). Move down the top stem so that the distance
between the valve stem and actuator top stemshould be gap 2.
Fit the clamp to align with both stems thread. Close the valve fully. Line up the stroke indicator with the clamp indicator
arrow and check actuator for operation. Tighten the socket head screws after adjusted the
rated stroke.
C. Actuator replacement (mounting) Mount the new or repaired actuator on top of the
bonnet, using a suitable lifting device. Insert the yoke nut and tightly fasten the yoke by
turning the yoke nut clockwise using tighteningtools.
Connect air line and accessories. Tighten stem socket head screws (1a**) and hexa-
gon nuts (1b**) with stem lock nut (5**).
CAUTION:Beware of the plug movement!Do not use air pressure higher than what specified on theidentification plate.
Fig. 10 Measurement of Gap 2
4 GV 74 en 9
D. Type ‘VC’ Springless Cylinder, Double Acting Actua-tor
This actuator is springless cylinder, double actingactuator, can use the 3/8”, 1/2” NPT port according tospecified on the data sheet for all air lines.
Refer to the model VC double acting cylinder actua-tor manuals for further information on their installa-tion, maintenance and operation..
7 TOOLSRemoval of the actuator L- wrench set (mm) Hex. socket wrench set Chisel and hammer (10 pound) +,- drivers
8 ORDERING SPARE PARTS
When ordering spare parts, always include the followinginformation: type code, sales order number, serial number number of the parts list, part number, name of the
part and quantity requiredThis information can be found from the identification plateor documents.
Fig. 11 VD Actuator
V-A (Valve-Actuator) Mounting Part (**)
1** CLAMP 1a**SOCKET HEAD SCREW1b** HEXAGON NUT 3**YOKE NUT (see above VD fig.)5** STEM LOCK NUT 6** LOCK WASHER
VD Actuator part
1. YOKE 10. LOWER CASE 18 TOP STEM 20. UPPER CASE21. LIFTING EYE NUT 22. WASHER 23. HEXAGON SCREW 24. HEXAGON SCREW25. HEXAGON NUT 30. IDENTIFICATION PLATE 32. INDICATOR 32a. ROUND HEAD SCRREW34. VENT CAP 99. AIR SUPPLY PORT
Direct Action actuator(Air to Close, stem extend)
Reverse Action actuator(Air to Open, stem retract)
CAUTION:Avoid to turn the valve plug and stem when plug is onseat ring to prevent the seating line from being dama-ged.
NOTE:Always use original spare parts to make sure that the valvefunctions as intended.
10 4 GV 74 en
9 EXPLODED VIEW AND PARTS LIST
*) Delivered as a set**) V-A Mounting Parts
Item Description Recommended spare part1 BODY2 PLUG SET3* PLUG5* STEM3** YOKE NUT6* PLUG PIN7 SEAT RING
7a SEAT RING8 BONNET
4** GUIDE BUSHING9a GLAND9b GLAND FLANGE12 DISK SPRING ASS'Y13 STUD14 STUD17 HEXAGON NUT18 HEXAGON NUT21 LANTERN RING26 BOTTOM FLANGE65 BODY GASKET X
65 a BODY GASKET X67 PACKING SPACER69 PACKING RING X
Live Load Spring
4 GV 74 en 11
10 DIMENSIONS AND WEIGHTS
10.1 Valve GW
150 # / 300 # / 600 #
NOTEP.C.D = Pitch Circle Diameter
Dimension (mm) A B C D E F G H Weight (kg)
Size(mm) 150# 300# 600# 150# 300# 600# STD EXT COMMON 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600#
025 184 197 210 160 160 160 130 250 110 110 125 125 15.9 19.1 19.1 79.4 88.9 88.9 4 4 4 20 21 33040 222 235 251 178 178 178 155 295 110 125 155 155 15.9 22.2 22.2 98.4 114.3 114.3 4 4 4 41 43 50050 254 267 286 197 197 197 184 295 110 150 165 165 19.1 19.1 19.1 120.7 127 127 4 8 8 57 62 73080 298 318 337 238 238 238 235 330 115 190 210 210 19.1 22.2 22.2 152.4 168.3 168.3 4 8 8 100 104 113100 352 368 394 270 270 270 238 380 140 230 255 275 19.1 22.2 25.4 190.5 200 215.9 8 8 8 136 141 156150 451 473 508 330 330 330 280 430 150 280 320 355 22.2 22.2 28.6 241.3 269.9 292.1 8 12 12 238 249 322200 543 568 610 410 410 460 375 490 150 345 380 420 22.2 25.4 31.8 298.5 330.2 349.2 8 12 12 351 375 451250 673 708 752 457 457 490 416 600 150 405 445 510 25.4 28.6 34.9 362 387.4 431.8 12 16 16 779 847 982
Dimension(inch) A B C D E F G H Weight (lbs)
Size(inch) 150# 300# 600# 150# 300# 600# STD EXT COMMON 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600#
1" 7.2 7.8 8.3 6.3 6.3 6.3 5.1 9.8 4.3 4.3 4.9 4.9 0.6 0.8 0.8 3.1 3.5 3.5 4 4 4 44 46 731-1/2" 8.7 9.3 9.9 7 7 7 6.1 11.6 4.3 4.9 6.1 6.1 0.6 0.9 0.9 3.9 4.5 4.5 4 4 4 90 95 110
2" 10 10.5 11.3 7.8 7.8 7.8 7.2 11.6 4.3 5.9 6.5 6.5 0.8 0.8 0.8 4.8 5 5 4 8 8 126 137 1613" 11.7 12.5 13.3 9.4 9.4 9.4 9.3 13 4.5 7.5 8.3 8.3 0.8 0.9 0.9 6 6.6 6.6 4 8 8 221 229 2494" 13.9 14.5 15.5 10.6 10.6 10.6 9.4 15 5.5 9.1 10 10.8 0.8 0.9 1 7.5 7.9 8.5 8 8 8 300 311 3448" 17.8 18.6 20 13 13 13 11 16.9 5.9 11 12.6 14 0.9 0.9 1.1 9.5 10.6 11.5 8 12 12 525 549 7108" 21.4 22.4 24 16.1 16.1 18.1 14.8 19.3 5.9 13.6 15 16.5 0.9 1 1.3 11.8 13 13.7 8 12 12 774 827 994
10" 26.5 27.9 29.6 18 18 19.3 16.4 23.6 5.9 15.9 17.5 20.1 1 1.1 1.4 14.3 15.3 17 12 16 16 1717 1867 2165
DRILLING
Dia. Of Hole = FPitch Circle Dia. = GNo of Hole= H
EXTENSION
12 4 GV 74 en
10.2 Actuators VD, VC
Dimension(mm) Without handwheel With handwheel
Size(mm) A2 Bd / Bhd Br / Bhr Weight
(kg) A2 A3 Bdh Brh Weight (kg)
VD_25 E 255 348 373 12 255 312 110 170 23VD_25 D 255 373 395 17VD_29 E 295 391 416 18 295 312 122 182 29VD_29 D 295 431 453 26VD_37 E 375 464 489 28 375 352 131 211 43VD_37 D 375 514 535 46
Dimension(inch) Without handwheel With handwheel
Size(inch) A2 Bd / Bhd Br / Bhr Weight
(lbs) A2 A3 Bdh Brh Weight (lbs)
VD_25 E 10 14 15 26 10 12 4 7 51VD_25 D 10 15 16 37VD_29 E 12 15 16 40 12 12 5 7 64VD_29 D 12 17 18 57VD_37 E 15 18 19 62 15 14 5 8 95VD_37 D 15 20 21 101
Standard spring High spring Standard springVDD/R E VDD/R D Side handwheel(25/29/37)
Br Bd Bhr
Bhd
Brh
Bdh
A2A2 A3
4 GV 74 en 13
NOTE1. "E" refers to Spring range 0.8~2.62. "D" refers to Spring range 1.5~3.43. "Br / Bhr" refers to reverse acting actuator, VDR E / D4. "Bd / Bhd" refers to direct acting actuator, VDD E / D5. "Cdh / Crh" Top side handwheel actuator, VD_48/55
Dimension (mm) Without handwheel With handwheel
Size(mm) A2 Bd / Bhd Br / Bhr Weight
(kg) Bdh Brh Cdh Crh Weight (kg)
VD_48 E 486 652 677 86 896 865 1102 1072 112VD_48 D 486 702 724 118 946 915 1152 1122 144VD_55 E 566 695 720 112 940 910 1145 1115 145VD_55 D 566 745 767 152 990 960 1195 1165 185
Dimension (inch) Without handwheel With handwheel
Size(inch) A2 Bd / Bhd Br / Bhr Weight
(lbs) Bdh Brh Cdh Crh Weight (lbs)
VD_48 E 19 26 27 190 35 34 43 42 247VD_48 D 19 28 29 260 37 36 45 44 317VD_55 E 22 27 28 247 37 36 45 44 320VD_55 D 22 29 30 335 39 38 47 46 408
Top side handwheel(VDD48/55) Top side handwheel(VDR48/55)
BrhBd
h
Crh
Cdh
14 4 GV 74 en
11 Actuator dimensions
11.1 VC cylinder actuators without handwheel
VC actuators without handwheel
VC actuators without handwheel
C
C
VC, without volume chamber VC, with volume chamber
B1
B2
Stroke(mm)
# 30 # 40 # 50 C 370 C 460 C 560B1 Weight(kg) B1 Weight(kg) B1 Weight(kg)B2 A B B2 A B B2 A B
40640
92 115810
120 148810
186 234760 935 935
50650
94 118820
123 152820
189 237790 965 965
60660
97 121830
126 155830
192 242820 995 995
70670
100 124840
128 159840
195 246850 1025 1025
80680
103 127850
131 162850
198 251880 1055 1055
90690
106 130860
134 166860
201 256910 1085 1085
100700
108 133870
137 173870
203 261940 1115 1115
120720
114 139890
142 177890
209 2701000 1175 1175
140910
148 184910
215 2791235 1235
180950
159 198950
227 2981355 1355
Stroke(mm)
# 60 # 70 # 80 C 660 C 710 C 820B1 Weight(kg) B1 Weight(kg) B1 Weight(kg)B2 A B B2 A B B2 A B
100954
255 344955
322 438954
378 5191199 1203 1207
120974
262 355975
330 450974
386 5311259 1263 1267
140994
269 365995
338 461994
394 5431319 1323 1327
1801034
283 3861035
354 4841034
410 5671439 1443 1447
2401094
303 4171095
377 5181094
435 6041619 1623 1627
2801134
451 6281747
Stroke(mm)
# 30 # 40 # 50 C 15 C 18 C 22B1 Weight(lbs) B1 Weight(lbs) B1 Weight(lbs)B2 A B B2 A B B2 A B
4025
203 25432
265 32632
410 51630 37 37
5026
207 26032
271 33532
417 52231 38 38
6026
214 26733
278 34233
423 53432 39 39
7026
220 27333
282 35133
430 54233 40 40
8027
227 28033
289 35733
437 55335 42 42
9027
234 28734
295 36634
443 56436 43 43
10028
238 29334
302 38134
448 57537 44 44
12028
251 30635
313 39035
461 59539 46 46
14036
326 40636
474 61549 49
18037
351 43737
500 65753 53
Stroke(mm)
# 60 # 70 # 80 C 26 C 28 C 32B1 Weight(lbs) B1 Weight(lbs) B1 Weight(lbs)B2 A B B2 A B B2 A B
10038
562 75838
710 96637
833 114447 47 48
12038
578 78338
728 99238
851 117150 50 50
14039
593 80539
745 101639
869 119752 52 52
18041
624 85141
780 106741
904 125057 57 57
24043
668 91943
831 114243
959 133264 64 64
28045
994 138569
4 GV 74 en 15
11.2 VC cylinder actuators with handwheel
VC actuators with handwheel
VC actuators with handwheel
CC
VC, with optional handwheel VC, with optional handwheel& volume chamber
B1
B2Stroke (mm)
#30 #40 #50 C 370 C 460 C 560B1 Weight(kg) B1 Weight(kg) B1 Weight(kg)B2 A B B2 A B B2 A B
40930
134 1571095
180 2081095
246 2941055 1220 1220
50940
137 1601105
183 2121105 249
2991085 1250 1250
60950
139 1631115
186 2151115 252
3031115 1280 1280
70960
142 1671125
188 2191125 255
3081145 1310 1310
80970
144 1701135
191 2221135 258
3131175 1340 1340
90980
147 1731145
194 2261145 261
3181205 1370 1370
100990
150 1761155
197 2301155 263
3221235 1400 1400
1201010
155 1831175
202 2371175 269
3321295 1460 1460
1401195
208 2441195 275
3411520 1520
1801235
219 2581235 287
3601640 1640
Stroke (mm)
#60 #70 #80 C 660 C 710 C 820B1 Weight(kg) B1 Weight(kg) B1 Weight(kg)B2 A B B2 A B B2 A B
1001239
315 4041240
368 5021289
438 5791484 1488 1542
1201259
322 4151260
376 5141309
446 5911544 1548 1602
1401279
329 4251280
384 5251329
454 6031604 1608 1662
1801319
343 4461320
400 5481369
470 6271724 1728 1782
2401379
363 4771380
423 5821429
495 6641904 1908 1962
2801469
511 6882082
Stroke (mm)
#30 #40 #50 C 15 C 18 C 22B1 Weight(lbs) B1 Weight(lbs) B1 Weight(lbs)B2 A B B2 A B B2 A B
4037
295 34643
397 45943
542 64842 48 48
5037
302 35344
403 46744
549 65943 49 49
6037
306 35944
410 47444
556 66844 50 50
7038
313 36844
414 48344
562 67945 52 52
8038
317 37545
421 48945
569 69046 53 53
9039
324 38145
428 49845
575 70147 54 54
10039
331 38845
434 50745
580 71049 55 55
12040
342 40346
445 52246
593 73251 57 57
14047
459 53847
606 75260 60
18049
483 56949
633 79465 65
Stroke (mm)
#60 #70 #80 C 26 C 28 C 32B1 Weight(lbs) B1 Weight(lbs) B1 Weight(lbs)B2 A B B2 A B B2 A B
10049
694 89149
811 110751
966 127658 58 61
12050
710 91550
829 113352
983 130361 61 63
14050
725 93750
847 115752
1001 132963 63 65
18052
756 98352
882 120854
1036 138268 68 70
24054
8001052 54
933 128356
1091 146475 75 77
28058
1127 151782
16 4 GV 74 en
12 TYPE CODE
VALVE CONSTRUCTIONS
TRIM CONSTRUCTIONS
OTHERS
* The body, bonnet, trim materials are subject to change as equivalent depending on detail design.
Globe 3-Way, Diverting / Mixing type, Series GW1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
GW 02 C W A J2 X P1 X BC S2 P1 X S F X S A X A L FC
1. VALVE SERIESGW Globe 3-way, Diverting type
2. BODY SIZE01 1" / DN 25 1H 1-1/2" / DN 4002 2" / DN 50 03 3" / DN 8004 4" / DN 100 06 6" / DN 15008 8" / DN 200 10 10" / DN 250YY Special
3. PRESSURE RATINGC ASME class 150 D ASME class 300
Optional pressure ratingF ASME class 600 Y Special
4. END CONNECTIONW Flanged RF, ASME B16.5
Optional end connectionV Socket welding, ASME B16.11Q Butt welding, ASME B16.25Y Special
5.BONNET CONSTRUCTION
Bonnet type Actuator connectionA Standard Standard actuator sizeB Standard Applicable for VD_48/55 (3",4" only)
Optional bonnet constructionY Special Special
6. BODY & BONNET MATERIALJ2 A216 gr. WCB S6 A351 gr. CF8M
Optional body & bonnet materialS4 A351 gr. CF8 S9 A351 gr. CF3S1 A351 gr. CF3M YY Special
7. BEARINGS (TRUNNION / THRUST BEARING)B Model B Y Special
8.PLUG MATERIAL
Material DescriptionP1 410 SS Standard for carbon steel bodyT6 316 SS Standard for stainless steel body YY Special Special materials
9. PLUG APPLICATIONX Not applicableA Cobalt based alloyY Special
10.STEM MATERIAL
Material DescriptionBC 630 SS + HCr Standard for carbon steel bodyTC 316 SS + HCr Standard for stainless steel body YY Special Special materials
11. SEAT TYPES2 Double metal seatYY Special
12.SEAT MATERIAL
Seat DescriptionP1 410 SS Standard for carbon steel bodyT6 316 SS Standard for stainless steel body YY Special Special materials
13. SEAT APPLICATIONX Not applicableA Cobalt based alloyY Special
14. PACKING TYPES Standard packing
Optional packing typeL Live loaded packingY Special
15. PACKING MATERIALG PTFE + Carbon fiber
Optional packing materialF Graphite (with mold and braided)Y Special
16. SEALS MATERIALX Not applicable Y Special
17. GASKET MATERIALS S/W gasket type, 316 SS + Graphite for standard
Optional gasket materialH S/W gasket type, 316 SS + Graphite for high temp.L S/W gasket type, 316 SS + PTFEY Special
18. STUD / NUT MATERIALA A193 gr. B7 / A194 gr. 2HB A193 gr. B8 / A194 gr. 8
Optional bolting materialH A193 gr. B16 / A194 gr. 4Y Special
19. OPTIONSX Not ApplicableM Globe 3-Way, Mixing typeY Special
4 GV 74 en 17
TRIM TYPE & RATED Cv
20.Sign TRIM TYPE 21.
SignTRIM
CHARACTERISTIC22.
Sign
RATED Cv
DescriptionBody Size and Stroke
1" Srk. 1-1/2" Srk. 2" Srk. 3" Srk. 4" Srk. 6" Srk. 8" Srk. 10" Srk.A Cylindrical plug type L Linear FC Full capacity 10 (15) 22 (20) 36 (30) 76 (40) 126 (50) 274 (60) 490 (70) 760 (70)
Q Quick-Opening 1A 1-step reduction 6 (15) 14 (20) 22 (30) 46 (40) 76 (50) 168 (60) 300 (70) 460 (70)2A 2-step reduction 4 (15) 10 (20) 14 (30) 28 (40) 46 (50) 100 (60) 180 (70) 280 (70)3A 3-step reduction 2 (15) 6 (20) 10 (30) 16 (40) 30 (50) 64 (60) 120 (70) 170 (70)
Y Special Y Special YY Special Contact Metso for Cv details* Rated Cv is separeted depending on the trim type & trim characteristic. * Srk. & number in the bracket means the valve stroke.
18 4 GV 74 en
4 GV 74 en 19
South Korea, 235 Cheomdansaneop 1-ro, Daesowon-myeon, Chungju-si, Chungbuk-do, 27466, Korea Tel. +82 43 852 7708, Fax +82 43 841 9890Europe, Vanha Porvoontie 229, P.O. Box 304, FI-01301 Vantaa, Finland. Tel. +358 20 483 150. Fax +358 20 483 151
North America, 44 Bowditch Drive, P.O. Box 8044, Shrewsbury, M A 01545, USA. Tel. +1 508 852 0200. Fax +1 508 852 8172South America, Av. Independéncia, 2500-Iporanga, 18087-101, Sorocaba-São Paulo, Brazil. Tel. +55 15 2102 9700. Fax +55 15 2102 9748
Asia Pacific, 238B Thomson Road, #17-01 Novena Square Tower B, Singapore 307685. Tel. +65 6511 1011. Fax +65 6250 0830China, 11/F, China Youth Plaza, No.19 North Rd of East 3rd Ring Rd, Chaoyang District, Beijing 100020, China. Tel. +86 10 6566 6600. Fax +86 10 6566 2583
Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 6836www.metso.com/valves
Metso Flow Control Inc.
20 4 GV 74 en