cost comparison of tuners h. hayano, kek 05132014 awlc14 srf-wg@fnal
TRANSCRIPT
![Page 1: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/1.jpg)
Cost comparison of tuners
H. Hayano, KEK05132014
AWLC14 SRF-WG@FNAL
![Page 2: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/2.jpg)
Performance comparison at S1-Global experiment
![Page 3: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/3.jpg)
Slide-jackSaclayBlade
Mechanical stroke
Piezo stroke
Blade(1+2) Blade(only 1)
Saclay(only 2) Saclay(only 1)
Slide-jack(center)
Slide-jack(end)
![Page 4: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/4.jpg)
Blade
Saclay
Slide-jack(center)
Slide-jack(end)
![Page 5: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/5.jpg)
Half-sine wave compensation
Adaptive F.F.compensation
Detuning offset < 50Hzfor every tuner
Every tuner worked well.
![Page 6: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/6.jpg)
TDR design choice
Tuner design should keep cavity plug-compatible interface. flange-to-flange length, support tab interval length, coupler-to-coupler interval length, etc.
Tuner should work at 31.5MV/m gradient within 50Hz residual detuning.
Tuner should have low-cost.
Blade tuner was selected for TDR design and cost estimation basement
If we can make new design keeping above condition, it is worth considering and doing R&D.
Adaptation of Saclay Tuner to ILC cavity design was considered.
![Page 7: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/7.jpg)
36mm
XFEL TESLA-Cavity
FNAL ILC-Cavity
Length difference between TESLA cavity and ILC cavity
![Page 8: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/8.jpg)
Saclay tuner for TESLA cavity
![Page 9: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/9.jpg)
stretchrelease
No interference to other boundary
Modified Saclay tuner design for ILC cavity
![Page 10: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/10.jpg)
No interference of pickup cables to the tuner arm.No interference of motor to the next cavity input coupler.
Stiffness is not yet examined, it is worry.
![Page 11: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/11.jpg)
release
![Page 12: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/12.jpg)
stretch
![Page 13: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/13.jpg)
TDR Blade tuner for ILC cavity
![Page 14: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/14.jpg)
Parts Picture from FNAL installation manual
![Page 15: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/15.jpg)
Parts List from FNAL installation manual
![Page 16: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/16.jpg)
In order to make fare cost comparison,I asked cost estimation to the same company for both of
(1) TDR blade tuner design(2) Modified Saclay tuner design
![Page 17: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/17.jpg)
TDR Blade tuner Components for fabrication
36 parts
Motor, gear, Bolts and nuts are excluded
( sorry, this picture is not correct. The number of parts will be much more.)
![Page 18: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/18.jpg)
Modified Saclay tuner Components for fabrication
21 parts
Motor, gear, Bolts and nuts are excluded
![Page 19: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/19.jpg)
Cost estimation comparison
TDR Blade tuner design Modified Saclay tuner design
* Motor and harmonic drive are in the both list,But not included into cost.
( Cost = materials + machining + inspection + assembly + company benefit )
Cost (Blade tuner) : (Modified Saclay tuner) = 1 : 0.52
Component list Component list
![Page 20: Cost comparison of tuners H. Hayano, KEK 05132014 AWLC14 SRF-WG@FNAL](https://reader030.vdocument.in/reader030/viewer/2022032600/56649dca5503460f94ac06ba/html5/thumbnails/20.jpg)
Conclusion
The modified Saclay tuner for ILC cavity was designed.Their cost was compared to TDR Blade tuner by the one company.The result was 52% of TDR Blade tuner, for the mechanical parts fabrication and assembly.
However, the modified Saclay tuner for ILC cavity design need to be done further study of tuning range, stiffness, toughness, etc.The R&D is required.