FUJIFILM MEDICAL SYSTEMS USA, INC.

TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

FINAL SITE PLAN

JUNE 08, 2016 2016-165-TYP

1 of 11

HQ

FINAL DRAWING PLANS - APPROVALCUSTOMER

DATE

CUSTOMER SIGNATURE

YOUR SIGNATURE APPROVES THIS FINAL DRAWING FOR ACCEPTANCE TO FORWARD TO

YOUR ARCHITECT - CONTRACTOR TO IMPLEMENT INTO THEIR FINAL DRAWING SET

Customer to verify freight size and integrity of any and all elevator(s) used for routing Fujifilm Medical Systems USA equipment.

Fujifilm Medical Systems USA representative.Customer to coordinate routing of Fujifilm Medical Systems USA equipment prior to equipment arrival with local

plans without prior notification.

to design and incorporate our final site plan drawings to your architectural construction documents. Fujifilm Medical Systems USA

It is the customer's responsibility to secure a storage area for equipment on site prior and during installation.

Fujifilm Medical Systems USA reserves the right to make changes to equipment and detailed specification regarding thesepreliminary plans shall not be used for construction documents, please refer to the latter final site plan drawings.

This drawing set is the sole property of Fujifilm Medical Systems USA. It's use is authorized for the customer architect of record

These drawings are provided with the understanding by providing such documents, does not alter any of the terms and conditions

damages resulting (from any matter) from the use of the attached drawings.Also Fuji Medical Systems USA or their agents will not be held liable for any direct, indrect, special, incidental or consequentialFujifilm Medical Systems USA makes no warranty or representation, either express or implied with respect to the attached drawings.

architects, engineers, or other design construction professional in the preparation of official construction documents.requirements. The information contained in this drawing set is provided for the use of customers and their designatedThese drawings are reference drawings (only), illustration of general equipment layout and facility-related equipment

Minimum equipment entry door height 80 INCHES

Minimum equipment entry door width 42 INCHES (recommended)

Passageways and Corridors 60 INCHES

The customer shall supply network drops for IP application.All network outlets will installed and set to 100 base T full duplex and checked prior to equipment install.

Customer to provide an IT representative readily available during the equipment installation period.

All power connections shall be dedicated independent connections to the power distribution panel.

All power shall be guaranteed by the owner to meet the power specificationsnormally associated powering medical electronic equipment.

Please refer to your final site plan drawing for site specific power requirements.

Equipment ambient temperature range 59 - 90 Degrees Fahrenheit.

Relative humidity should be between 20 - 75 percent non-condensing.

The room the equipment is installed within should be kept dust free.

of said sale between Fujifilm Medical Systems USA and their customer.

The customer is responsible for the complete an accurate incorporation of all specifications and requirements from these

siting and placement of purchased Fujifilm Medical Systems USA equipment.These drawing are not to be used as construction documents. It is the sole responsibility of the customer to ensure the correct

reference drawings to your architect of record for use of site preparation. Sufficiency of final site plans and specifications, specifically including

Worldwide Healthcare Designs, Inc. (WHD) is Fujifilm Medical Systems USA sole designer for said project.

All network drops will be installed and marked on the connection prior to installation of the equipment.

It is the customer's responsibility to be in compliance with all local, state and federal safety, electrical, and building

This shall include any and all expenses for room and structural alterations. Site preparation shall be in accordanceIt is the customer's sole responsibility and their expenses for room preparation of said room for this equipment sale.

Any time delay from the removal of the latter may result in an extended installation period.

The customer shall obtain all permits and required licenses needed for Federal, State and Local regulations,

The customer should provide Fujifilm Medical Systems USA a construction time-line chart and also

Power - 3 phase, 480 VAC (5 WIRE)Breaker - 80 amp for 80kW generator

All doors, windows and radiation protection installed and finished.

All electrical conduits, raceway, junction boxes and outlets installed and operational.

flush with ceiling grid and operational.Please have walls painted, baseboards installed, all floors tiled, ceiling tiles installed and light fixtures installed

All plumbing must be installed, finished and operational. Any plumbing connections in the immediate area of

All contractors supplied cables must be pulled and terminated at designated locations.

X-ray Procedure and Control Room - a dust free environment.

and free of lateral or longitudinal interference.All support structures used for install and equipment support must be installed, level (within one-eight inch end to end),

Incoming power to X-Ray room breaker panel connected and operational.

the new installation that is not being used must be capped and covered.

with this set of final site plans and specifications provided by Fujifilm Medical Systems USA.

codes relevant to Fujifilm Medical Systems USA final site plans, equipment and installation.

Radiation protection is not shown on these set of plans, However the customer at their own expense shall obtain a

Also the customer shall bear any expense in complying with any related rules, regulations and ordinances.in connection with the construction. installation and operation of their purchased equipment.

The customer shall advise a Fujifilm Medical Systems USA of any adverse conditions at or near the sitethat could affect the installation scheduling and service support team travel.

but not limited to the accuracy of dimensions (based on information provided), shall be the sole responsibility of the customer.

It is the customer's sole responsibility to properly remove and dispose of any hazardous materials - at their expense.

It is the customer's responsibility to properly remove and make the site conditions safe for installation and operation.

follow-up with scheduled construction meeting notice for project area(room).This is to insure coordination between contractor(s) with delivery and installation of purchased equipment.

All dimensions are measured from finished surfaces, unless otherwise specified on drawing.

We recommend that during equipment delivery and installation, for the customer to protect finished floors, walls andany areas, including other equipment within area of install with protective covering.

Installation will not commence until room is clean and dust free. All contractors equipment must be removed prior to insall.Fujifilm Medical Systems USA will not be responsible for any lost, damaged tools and materials from customer's contractors.

licensed radiation physicist to specify need of radiation protection.

Installation will not commence until room is clean and dust free. All contractors equipment must be removed prior to install.Fujifilm Medical Systems USA reserves the right to refuse delivery and installation due to the room is not properly preparedper accordance with Fujifilm Medical Systems USA final site plans.

The customer or contractor shall supply and install all materials and other features called-out from Fujifilm Medical Systems USA final site plans.

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

NOT TO SCALE

2016-165-TYP

2 of 11

CUSTOMER-CONTRACTOR TO PROVIDE DESK, CHAIR, AND CABINETRY PER THEIR NEEDS.

CUSTOMER 'S PHYSICIST TO DETERMINE AREA SHIELDING REQUIREMENTS.

BY THE CUSTOMER. CONTROL ROOM MAXIMUM WALL HEIGHT NEEDS TO BE 7 ;- 6 ' '.LEAD LINED WINDOWS-WALLS, CABINETRY, COUNTER AND SINKS ARE TO BE PROVIDED

PLEASE VERIFY ROOM DIMENSIONS TO THE ACTUAL SITE CONDITIONS.

2.

5.

4.

3.

1.

( IF APPLICABLE )

NEW WALLS

EXISTING WALLS

EXISTING WALLS TO BE REMOVED

CUSTOMER TO SUPPLY ALL CONSTRUCTION

14 '-0 ' ' RAILS SHOWNPLAN NORTH

N

EQUIPMENT PLAN

EQUIPMENT LEGEND

*CUSTOMER/CONTRACTOR TO PROVIDE MEDICAL GASES - PER CODE AND LOCATION6.

RADROOM

SEENOTE 2

SEE NOTE 3

SEE NOTE 3

TOP

EXISTINGBREAKER

EXISTING4 ' - 0 ' ' DOOR

HALF WALLMAX. 7 '-0 ' ' HIGH

PLEASE FIELD VERIFYALL EXISTING INTERNALWALL DIMENSIONS, DOORLOCATIONS, ETC...

PLEASE FIELD VERIFYALL EXISTING INTERNALWALL DIMENSIONS, DOORLOCATIONS, ETC...

EXISTING3 ' - 0 ' ' DOOR

CONTROLROOM

BATHROOM

PLEASE FIELD VERIFYALL EXISTING CEILINGSUPPORT (QTY. 7)2 '- 2 ' ' ON CENTER

PLEASE FIELD VERIFYEXISTING TRENCH DUCT

PLEASE FIELD VERIFYEXISTING RISER

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

3 of 11

EQUIPMENT DETAILS

HEIGHT - 21.5 ' '

TOP

SIDE BACK

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

NOT TO SCALE

2016-165-TYP

4 of 11

ELECTRICAL PLAN

PLAN NORTH

N

FIELD VERIFY

FIE

LD

VE

RIF

Y

CONTROLROOM

FIE

LD

VE

RIF

Y

RADROOM

EXISTINGBREAKER

FIELD VERIFY

FIELD VERIFY

FIELD VERIFY

FIELD VERIFY

FIELD VERIFY

FIELD VERIFY

FIE

LD

VE

RIF

Y

FIE

LD

VE

RIF

Y

FIE

LD

VE

RIF

Y

FIE

LD

VE

RIF

Y

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

5 of 11

GENERATORSPECIFICATIONS NOTES

ELECTRICAL INSTALLATIONPOINT TO POINT DIAGRAM

TOP

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

6 of 11

STRUCTURAL PLAN

LT

AB

LE C

LTABLE C

SEE DETAILSFIELD VERIFY

LC

HE

ST S

TA

ND

C SEE

DE

TA

ILS

FIE

LD

VE

RIF

Y

FIE

LD

VE

RIF

Y

FIELD VERIFY FIELD VERIFY

PLAN NORTH

N

FIE

LD

VE

RIF

Y

RADROOM

CONTROLROOM

BATHROOM

FIELD VERIFY FIELD VERIFY

FIE

LD

VE

RIF

Y

FIE

LD

VE

RIF

Y

SEE

DE

TA

ILS

FIE

LD

VE

RIF

Y

FIELD VERIFY

PLEASE FIELD VERIFYALL EXISTING CEILINGSUPPORT (QTY. 7)2 '- 2 ' ' ON CENTER

CUSTOMER TOADD ONE (1) NEWCEILING SUPPORT

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

7 of 11

POWER WIRES FROM FUJI MEDICALSIGNAL CABLES. (SEE RACEWAY LAYOUT, DIAGRAM).

ALL TROUGH SHALL BE SQUARE-D, WALKER DUCT (OR EQUAL) FLOOR AND WALL TRENCH DUCT.SIZES SHALL BE AS SPECIFIED ON DRAWINGS, OR PROVIDE EQUIVALENT NOMINAL SIZES AVAILABLEFROM MANUFACTURER (SEE TROUGH LAYOUT, DIAGRAM). FLOOR TROUGH TO BE GASKETED TO

ALL TROUGH SHALL BE FLUSH WITH FINISHED SURFACES UNLESS OTHERWISE SPECIFIED AND PROVIDED WITH REMOVABLE COVERS THE LENGTH. COVERS SHALL BE CLEAR OF ANYOBSTUCTION FOR INSERTION OF PRE-PLUGGED CABLES. IF IT IS NECESSARY THAT THE TROUGHBE SURFACE MOUNTED, WHEN NOT INDICATED ON THESE FUJI MEDICAL DRAWINGS, ALL EQUIPMENT

PLACEMENT AND TRAVEL CLEARANCE MUST BE VERIFIED TO PREVENT EQUIPMENT AND TROUGHINTERFERENCE AND POSSIBLE EQUIPMENT DAMAGE. CONTACT FUJI MEDICAL PROFESSIONAL DESIGNSERVICES FOR PROPER VERIFICATION OF EQUIPMENT PLACEMENT AND TROUGH CLEARANCES.

REMOVABLE TYPE BARRIER STRIP AND CROSSOVERS MAY BE REQUIRED FOR SEPARATION OF A.C.POWER WIRES OR VIDEO COAX CABLES FROM FUJI MEDICAL SIGNAL CABLES. (SEE TROUGH LAYOUT,

PAINT ALL EXPOSED AREAS OF TROUGH. CONSULT WITH CUSTOMER ON MATCHING OR ACCENT COLORS.

WHEN ORDERING TROUGH DUCT AND REQUIRED FITTINGS FROM SQUARE-D OR WALKER PAKERSBURG,USE THE APPROPRIATE CATALOG NUMBERS FOR EACH ITEM TO EXPEDITE DELIVERY.

"SWEEP ELBOWS" FOR CORNER BENDS SHALL BE PROVIDED. THE FOLLOWING SQUARE-D CATALOGNUMBERS (OR EQUAL): "RWT-SFEE" FOR FLUSH MOUNTED TROUGH. "RWT-SSEES" FOR SURFACEMOUNTED TROUGH. NOTE: WHEN ORDERING, SPECIFY 10" OR 18" TROUGH USAGE.

ALL RACEWAY SHALL BE SURFACE MOUNTED ON FINISHED SURFACES UNLESS OTHERWISE SPECIFIEDAND SHALL BE PROVIDED WITH REMOVABLE COVERS, THE FULL LENGTH. COVERS SHALL BE CLEAROF ANY OBSTRUCTION FOR INSERTION OF PRE-PLUGGED CABLES.

PAINT ALL EXPOSED AREAS OF RACEWAY. CONSULT WITH CUSTOMER ON MATCHING OR ACCENT

ALL RACEWAY SHALL BE "WIREMOLD" BRAND (OR EQUAL) FOR FLOOR, WALLS, OR CEILING, UNLESSOTHERWISE SPECIFIED. (SEE RACEWAY LAYOUT, DIAGRAM FOR RECOMMENDED SIZES).

REMOVABLE TYPE BARRIER STRIP AND CROSSOVERS MAY BE REQUIRED FOR SEPARATION OF A.C.

DIAGRAM)

COLORS.

PREVENT ENTRY OF LIQUIDS.

NOT TO SCALE

THIS DETAIL IS A RECOMMENDATION ONLY. CONTRACTOR TO DETERMINE

THIS DETAIL APPLIES TO JUNCTION BOXES INDICATED ON FUJI MEDICAL'S FINAL

OPEINGS OF THESE BOXES SHALL FEATURE EXPOSED REMOVEABLE COVER

ACTUAL METHODS BASED ON SPECIFIC SITE CONDITIONS.

DRAWINGS WITH LETTER DESIGNATIONS JB1, JB2, ETC.

PLATES AS DESIGNATED.

WITH 2 DIVIDERS FOR

GROMMETTED OPENING FOR

VERTICAL RACEWAY RISER FORTUBERCRANE CABLES.

JUNCTION BOX AND CONDUITWITHIN WALL

TROUGH TUB TO MATCH JUNTION BOXOPENING THROUGH REAR OF RACEWAY/

SURFACE RACEWAY / TROUGH TUB

OPENING

GROMMET SHARP EDGES

COVER PLATE CUTAWAY VIEW

COVER PLATE

WALL LINE

CABLE SEPARATIONS.

CABLE ACCESS.

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

8 of 11

.25 ' ' ( 6.4MM ) MINIMUM THICK WASHER OR ELONGATED WASHER PLATES MUST BE PLACED AT

STRUT CHANNEL LONGITUDINAL TRACK SUPPORT SHALL BE FASTENED TO STRUT CHANNEL SPANNINGMEMBER BY USE OF APPROPRIATE HARDWARE MANUFACTURED BY UNISTRUT OR POWER STRUT.

CHANNEL LOCATED BETWEEN FINISHED CEILING LINE AND TOP OF FUJI MEDICAL LONGITUDINAL CLG. TRACK.EXPOSED STRUT CHANNEL LONGITUDINAL TRACK SUPPORT SHALL BE 1 5/8" DEEP SLOTTED

NOT TO SCALE

SLOTTED HOLES FOR THIS CONNECTION.

FUJI MEDICAL STRONGLY RECOMMENDS THAT THE CUSTOMER HIRE A STRUCTURAL ENGINEER( "ENGINEER OF RECORD" ) WHO IS REGISTERED AND CERTIFIED IN THE STATE IN WHICH THE CUSTOMER'S SITE IS LOCATED. THE ENGINEER OF RECORD SHALL BE RESPONSIBLE FOR PROVIDING AND APPROVING A DESIGN FOR ADAPTING THE SUPPORT STRUCTURE TO THE NEW OR EXISTING BUILDING STRUCTURE. THE CEILING SUPPORTSTRUCTURE INCORPORATING THE DESIGN OF THE ENGINEER OF RECORD SHALL BE SUP-PLIED AND INSTALLED BY CONTRACTOR, AS PART OF THE IRON WORK OR SPECIALTIES

A WELDED OR FABRICATED STRUCTURAL SUPPORT IS REQUIRED FOR CEILING MOUNTED X-RAY UNITS. ITS TOP MEMBER IS FASTENED TO THE FLOOR SLAB ( OR BUILDING STEEL ) ABOVE THE X-RAY ROOM. THE BOTTOM OF ITS LOWEST SPANNING MEMBER IS FLUSH WITH THE FINISHED CEILING TO WHICH THE STATIONARY CEILING TRACKS ARE FASTENED WITH MOUNTING HARDWARE SUPPLIED AND INSTALLED BY FUJI MEDICAL.

THE FOLLOWING GENERAL DETAILS INDICATE A BASIC SUPPORT METHOD THAT PERMITS TRANSVERSE AND LOGITUDINAL ADJUSTMENT OF BOLT CENTERS AT THE INSTALLATION SITE. IT CAN BE ADAPTED TO ACCOMMODATE THE VARIOUS ARCHITECTRAL CIRCUMSTANCES

THE SUPPORT MUST BE RIGID, SECURELY BRACED AND LEVEL IN BOTH DIRECTIONS AT THE FINISHED CEILING LINE. LENGTH AND LOADING CAPACITY WILL DEPEND ON THE SELECTED CEILING UNIT AND NUMBER OF CARRIAGE ASSEMBLIES TO BE BORNE. ACTUALEQUIPMENT LOADS FOR EACH ROOM ARE SPECIFIED ON THE FUJI MEDICAL SITE PLANNING DRAWINGS UNDER THE STRUCTURAL DETAIL SPECIFICATIONS.

FUJI MEDICAL SUGGESTS THROUGH BOLTING THE SUPPORT STRUCTURE TO BUILDING STRUCTURE WHENEVER POSSIBLE. FUJI MEDICAL WILL ALSO ACCEPT THE APPLICATION OF HILTI EXPANSIONANCHORS ( OR EQUAL ) IN LIEU OF THROUGH BOLTING. ACTUAL METHODS AND MATERIALS

SHALL BE DETERMINED BY ENGINEER OF RECORD. ALL SUPPORT MEMBERS, ANCHOR BOLTS,AND HARDWARE SHALL BE SUPPLIED AND INSTALLED BY CONTRACTOR. THE LENGTH OF BOLTSSHALL BE DETERMINED TO MEET SPECIFIC SITE REQUIREMENTS BY ENGINEER OF RECORD.

FUJI MEDICAL WILL ACCEPT THE USE OF UNISTRUT OR POWER STRUT SUPPORT MEMBERS FOR CONSTRUCTION, ONLY IF SUPPORT STRUCTURE IS DESIGNED AND CERTIFIED BY UNISTRUT OR POWER STRUT CORPORATION, IN CONJUNCTION WITH THEENGINEER OF RECORD. THESE STRUT CHANNEL MEMBERS MUST NOT BE WELDED TOGETHER.THE APPROPRIATE AVAILABLE HARDWARE SHALL BE APPLIED.

CENTERLINES OF THE TWO STRUCTURAL MEMBERS HOLDING THE SUSPENDED WEIGHTS ARESHOWN. UNISTRUT OR POWER STRUT FLUSH FINISHED CEILING SHALL BE IDENTIFIED AS THE SPANNING MEMBERS. THESE MEMBERS MUST BE LEVEL IN BOTH DIRECTIONS TO WITHIN1/16" ( 1.6MM ) AND BRACED TO PREVENT MOVEMENT IN ANY DIRECTION. THEY MUST BESECURED TO THE SLAB ABOVE AND/OR TO THE BUILDING STRUCTURE TO THE HOLD THE DEAD

INSTALLATION OF THE SUPPORT MAY BE AFFECTED BY OTHER ARCHITECTURAL OR MECHANICAL PROVISIONS WHICH MAY BE LOCATED IN THE SAME AREA. IN THIS CASE, COORDINATION OF THE REPRESENTATIVE MUST BE CONSULTED BEFORE ANY DEVIATION FROM THE SITE PLANNING

WEIGHTS INDICATED.

DRAWINGS IS UNDERTAKEN.

CONTRACT.

ENCOUNTERED AT EACH INSTALLATION.

- CUSTOMER IS RESPONSIBLE FOR MEETING SITE CONDITIONS FOR STATIC LOADS,

( WIDTH, DEPTH, STRENGTH, ETC...)- SUPPORT STRUCTURE MUST MEET ALL REQUIRED EQUIPMENT SUPPORT NEEDS.IS CERTIFIED BY A LICENSED/PROFESSIONAL STRUCTURAL ENGINEER.CUSTOMER CAN ALSO UTILIZE AN EXISTING SUPPORT STRUCTURE, ONLY IF THE STRUCTURE

FINISHED CEILING LINE

SPANNING MEMBER SUPPLIEDAND INSTALLED BY CONTRACTOR

FUJI MEDICAL LONGITUDINALCEILING TRACKMOUNTING SURFACE OF

FUJI MEDICAL LONGITUDINALCEILING TRACK

BOTTOM OF SPANNING MEMBERFLUSH WITH FINISHED CEILING LINE

EACH MEMBER 2'-2" O.C.

LEVELNESS, ETC...)

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

9 of 11

CONSTRUTION.

BRACES- UNISTRUT OR POWER STRUT ATTACHED TO VERTICAL COLUMNS AS SHOWN ON DETAIL.

CORPORATION. ALL STRUT MEMBERS SHALL BE SUPPLIED AND INSTALLED BY

LOCATION OF VERTICAL COLUMNS SHALL VARY DEPENDING ON BUILDING

STRUT CHANNEL SUPPORT SHOULD BE A PART OF SPECIALTIES SPECIFICATIONS,

SPANNING MEMBERS: UNISTRUT OR POWER STRUT FLUSH WITH FINISHED

VERTICAL COLUMNS: UNISTRUT OR POWER STRUT ATTACHED TO SPANNINGMEMBERS AS SHOWN ON GENERAL CEILING DETAILS SHEET. NUMBER AND

RECOMMENDED UNIVERSAL STRUT CHANNEL SUPPORT FRAMEALLOWS FOR TRANSVERSE AND LONGITUDINAL ADJUSTMENT AT TIME OF EQUIPMENTINSTALLATION. DETERMINATION OF THE ACTUAL DESIGN SHALL BE COORDINATEDAND APPROVED BETWEEN ENGINEER OF RECORD AND UNISTRUT OR POWER STRUT

CEILING. SPACED 2 '-2 ' ' O.C.

OMITTED

SEC. 10. NOT IRON SPECIFICATIONS.

CONTRACTOR.

O.C. TYPICAL

3

57.125 ' ' ( 1450 MM )

1

4

BRACE

REQUIRED FITTING

REQUIRED FITTING

VERTICAL COLUMN

FUJI MEDICAL LONGITUDINALCEILING TRACK

SPANNING MEMBER

REQUIRED FITTING

FINISHED CEILING LINE

REFERENCE TO 2 '-2 ' ' IS SHOWNFOR 2 ' x 4 ' CEILING TILES ONLY.SPACE BETWEEN SUPPORT RAILSCAN VARY BETWEEN 34.5 ' ' TO 53.125 ' '(BASED ON SEIMENS INSTALL MANUAL)

DRAWINGS TO MATCH FUJI MEDICALLONGITUDINAL CEILING TRACK SPACINGS.RAILS SUPPLIED AND INSTALLED

SPECIFIED ON SITE PLANNINGO.C. OR AS OTHERWISE

BY FUJI MEDICAL INSTALLATIONS.

NOT TO SCALE

DETAILSSEE GENERAL

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

10 of 11

EQUIPMENT DETAILS

ROOMWALL

MA

XIM

UM

VE

RT

ICA

L T

RA

VE

L

MIN

. VE

RT

ICA

L T

RA

VE

L

TELESCOPETUBE

SUPPORTARM

COLLIMATOR

NO

TE

: 1

4 ' -

0 '

' R

AIL

S -

ST

AN

DA

RD ROOM

WALL

58 1 8 ' ' ON CENTERINSTALLED BY FUJI

FUJIFILM MEDICAL SYSTEMS USA. Inc. TYPICALSD-EVO II EQUIPMENT PLANS

STAMFORD, CT 06801

X-RAY SUITEWITH D-EVO II

WHD-A.A.

JUNE 08, 2016

1/4"=1'-0

2016-165-TYP

11 of 11