data link antenna summary - west radio …€¦ · data link antenna summary zcg scalar, head...
TRANSCRIPT
DATA LINK ANTENNASUMMARY
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
Section 7
 Spread Spectrum Dipole, 853–929 MHz
 NEXT G Modem, 825–890 MHz
 NEXT G and GSM Bands, 825–960 MHz and 1710–2190 MHz
 Stud Mount Dipole, 900–930 MHz
 Flexible Whip, 900–930 MHz
 Collinear, 1885–1905 MHz
 Yagi DECT, 1880–1900 MHz
 Collinear, 2.4–2.5 GHz
 Stud Mount Dipole, 2.4 GHz
 Right-Hand Circular, 2.4–2.5 GHz
 Yagi, 2.4 GHz
 Yagi, 2.65 GHz
 Right-Hand Circular, 5.7–5.85 GHz
 WiMAX Power Divider, 2.4-2.5 GHz
CFD890Spread Spectrum Dipole
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth853 – 929 MHz Full Band
The CFD890 spread spectrum dipole is factory tuned to cover the full frequency range 853 to 929 MHz at less than 1.5:1 VSWR.
Construction consists of welded brass internals, aluminium ferrule and a black fibreglass radome standing 40 cm tall.
The dipole can be secured into any bracket with a 12.7 mm (½") minimum diameter hole using the stainless steel nut and washer at the base.
No metal ground plane is necessary for the antenna to operate effectively. Potential mount positions therefore include vehicles and numerous fixed locations where no metal exists. A variety of mounting brackets are available separately.
3 metres of RG58 low loss cable side exits from the mount ferrule.
An SMA Male connector is fitted to the cable.
An SMA Male connector is fitted to the 3 metre RG58 low loss cable.
40 cm
Construction
SPECIFICATIONS CFD890
Brass internals, aluminium ferrule, black fibreglass radome
VSWR
Impedance (Nom.)
Tuning
Polarisation
Cable
Connector
HeightWeight
Mounting
2.1 dBiGain
< 1.5:1
50 Ohms
Factory
Vertical
40 cm350 grams
Frequency Range 853 to 929 MHz full band
20 WattsMaximum Power
DC Grounding Yes
3 metres of RG58 low loss cable side exits from the ferrule
SMA Male fitted to the cable (Other connectors available)
Secure to any bracket with12.7 mm (½") minimum diameter hole using the stainless steel nut and washer at the base
H-Plane 360O Omnidirectional
MAGM90T800NEXT G Modem Antenna
with Magnetic Base
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth825 – 890 MHz NEXT G
The MAGM90T800 antenna with magnetic base is for use with a NEXT G modem operating in the frequency range 825 to 890 MHz. This compact portable model stands 32.5 cm tall and delivers 5 dBi gain.
The antenna is also suitable for a Next G cellular mobile phone.
Ideal for indoor use, the magnetic base mounts simply onto any flat metal surface. Easy to set-up, easy to remove and the detachable whip makes the antenna easy to store when not required.
The 4 cm diameter magnetic base is manufactured from moulded plastic with nickel plated brass fittings. An FME Male connector is housed inside the base. The black powder coated detachable stainless steel whip fits onto the 6 mm x 26 TPI thread.
The antenna is supplied with a 3 metre RG58 low loss solid core cable set with connectors fitted.
The FME female connector attaches into the antenna base. Â
The SMA male connector attaches into the Next G modem or Âcellular mobile phone.
Other connector options are available.
Black powder coated detachable stainless steel whip
3 metre RG58 low loss solid core assembled cable set
32.5 cm tall
Magnetic base with FME male connector
FME female fitted
SMA male fitted
Easy to set-up
Easy to store
SPECIFICATIONS MAGM90T800
NEXT G, 825 ─ 890 MHz
5 dBi
Less than 1.5:1 across the full band
5 Watts50 Ohms
Factory
Vertical
3 metres RG58 low loss solid core coaxial cable with FME Female and SMA Male connectors fitted
FME Male inside base
32.5 cm60 grams
4 cm diameter Magnetic Base ontoany flat metal surface
Cellular Mobile Phone Network Coverage
VSWR
Maximum PowerImpedance
Tuning
Polarisation
Cable Set Supplied
Connector
HeightWeight
Mounting
Nominal Gain
Construction
Magnetic base, moulded black plastic with nickel plated brass fittings, black powder coated stainless steel whip,6 mm x 26 TPI thread
GIDM-DBMultiband NEXT G and GSM
Cellular Mobile Phone Antenna
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth825 – 960 MHz NEXT G and GSM combined
Ideal for Data Link applications, key features of this GIDM-DB antenna are :
Multiband coverage across  both NEXT G and GSM cellular mobile phone networks combined.
Small size at just 27 cm tall. Â
2.1 dBi gain. Â
Ground independent. Â
Easily mounted to a vehicle guard, boot, truck mirror or any Âfixed location using the appropriate bracket.
The antenna is firmly secured into any 10 mm hole using the threaded stud and nut assembly at the base.
5 metres of RG58 low loss cable bottom exits through the base. The cable may be cut shorter if desired.
An FME Female connector is supplied. Other connectors are available upon request.
After securing the antenna in position and trimming the cable to the required length,fit the FME female crimp connector supplied.
Frequency Range
SPECIFICATIONS GIDM-DB
NEXT G and GSM networks combined825 to 960 MHz
VSWR
Maximum PowerImpedance
Tuning
PolarisationCable
Connector
HeightWeight
Mounting
2.1 dBiGain
Less than 1.6:1 across full band
5 Watts50 Ohms
Factory
Vertical5 metres RG58 Low Loss
FME female supplied, not fitted(Other connectors available)
27 cm280 grams
Secure into any bracket with minimum 10 mm diameter hole using the threaded stud and nut assembly at the base
Colour Black
GIDM90TNEXT G or GSM
Cellular Mobile Phone Antennas
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth825 – 960 MHz NEXT G or GSM
GIDM90T ground independent cellular mobile phone antennas are also useful for Data Link applications in either the NEXT G or GSM Bands. Just 45 cm tall with 5 .1 dBi gain, these models are a modest size and will deliver excellent performance.
The antennas are a rugged design with detachable stainless steel black powder coated whip.
No metal ground plane is necessary for the antenna to operate effectively.
Simply mount the antenna into any bracket with minimum 10 mm diameter hole using the nut and spring washer at the base.
4.5 metres of RG58 low loss cable bottom exits through the base. The cable may be cut shorter prior to fitting the FME Female crimp connector supplied.
Other connectors can be supplied as you may require.
An FME Female crimp connector is supplied, not fitted.
Other connectors are available upon request.
Frequency Range
SPECIFICATIONS GIDM90T(NextG)
NEXT G825 to 890 MHz
VSWR
Maximum PowerImpedance
Tuning
PolarisationCable
Connector
HeightWeight
Mounting
5.1 dBiGain
< 1.6:1 full band
5 Watts50 Ohms
Factory
Vertical4.5 metres RG58 low loss bottom exits
FME Female crimp supplied, not fitted(Other connectors available)
45 cm350 grams
Secure into any bracket with minimum 10 mm diameter hole using the threaded stud and nut assembly at the base
Colour Black
GIDM90T(GSM)
GSM890 to 960 MHz
5.1 dBi5 Watts50 Ohms
Factory
Vertical
40 cm350 gramsBlack
< 1.6:1 full band
SGDB-TPMMultiband NEXT G and GSM
Antenna Top
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 25 July 2012
Frequency Bandwidth825 – 960 MHz
1710 – 2190 MHzNEXT G and GSM
combined
For wireless data link applications anywhere across the NEXT G and GSM cellular mobile phone frequency range 825 to 960 MHz and 1710 to 2190 MHz, our popular SGDB-TPM multiband antenna top with 6.2 dBi gain offers an effective solution.
Key features are : Â Multiband coverage of both NEXT G and GSM networks combined. Â Modest size at 80 cm tall with an effective 6.2 dBi gain. Â Omnidirectional radiation pattern. Â Completely ground independent, mount anywhere, no metal groundplane is necessary. Â Rugged fibreglass radome available in Black, White or Brown.
5 metres of RG58 low loss solid core feeder cable side exits from the aluminium mount ferrule. An FME Female connector is fitted to the cable for easy installation. Other connector options are available, or an adaptor as you may require.
The stud, nut and washer at the antenna base permits these versatile mounting options :1. Simply secure the antenna into any 12.7 mm (½”) minimum diameter hole, route the
cable and connect to your data device.2. Fit an “L” bracket, such as our stainless steel model “GM1”, to any vertical panel or fascia
board. Insert the antenna, fit the washer, tighten the nut, route the feeder cable and connect to your data device.
3. Order our model “4266” threaded aluminium mast mount adaptor, screw in the antenna and secure to a mast or hockey stick bracket with the “UB3SS” stainless steel parallel clamp. Alternatively, use hose clamps.
GM1 4266
UB3SS
Optional Mounting Accessories
Cellular Mobile Phone Network Coverage
SPECIFICATIONS SGDB-TPM BLACK
NEXT G and GSM combined825 to 960 MHz and 1710 to 2190 MHz
6.2 dBi at 825 to 960 MHz3 dBi at 1710 to 2190 MHz
Gain
Less than 1.6:1 across the full band
30 Watts50 Ohms
Factory
5 metres RG58 low loss stranded cable side exits from the aluminium mount ferrule
FME female fitted (others options available)80 cm700 gramsSecure into any 12.7 mm (½”) min diameter hole
VSWR
Maximum Input PowerImpedance
Tuning
Cable
ConnectorHeightWeightMounting
Construction Fibreglass radome, copper radiating elements, aluminium ferrule, stud, nut and washer
BlackRadome Colour
VerticalPolarisation360O OmnidirectionalH-Plane32OE-Plane
SGDB-TPM WHITE SGDB-TPM BROWN
White Brown
1. GM1 : Stainless steel “L” bracket.2. 4266 : Aluminium mast mount adaptor, 150 mm x 25 mm.3. UB3SS : Stainless steel parallel clamp, or use hose clamps.
Optional MountingAccessories
An FME Female connector is fitted to the cable. Other connector options, or an adaptor, are available as you require.
MADB Multiband NEXT G and GSM Cellular Mobile Phone Antenna
with Folding Base
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 25 July 2012
The MADB cellular mobile phone antenna with folding base provides multiband coverage of both NEXT G and GSM networks combined with an effective 6.2 dBi gain. The antenna can also be most useful for data link applications.
Standing 90 cm tall, the MM1 folding base supplied as standard is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt.
This versatility makes the MADB model a perfect choice for mounting to boats, caravans, a trailer, outside on the fascia board of a building or any flat surface at any angle desired using four screws or bolts. The antenna can be folded down flat while not in use.
5 metres of RG58 low loss stranded cable side exits from the mount ferrule. The FME female connector fitted to the cable is rated for up to 30 watts input power.
The fibreglass radome is available in 3 colours; White, Black or Brown. Specify your preference when ordering.
This MADB antenna is identical in appearance to the MA477 model for 477 MHz UHF CB radio and MA1100 for AM/FM radio receive.
For those who prefer the ultimate in quality, durability and strength, the antenna is also available with the MM2 folding base which is constructed entirely from stainless steel. The order code is MADBSS.
The MM1 folding base supplied as standard is constructed from toughened plastic.
For those who prefer the ultimate in quality, durability and strength, the MM2 folding base is constructed entirely from stainless steel. This MM2 base is supplied with the MADBSS model.
An FME female connector is fitted to the cable.
SPECIFICATIONS MADB
Cellular Mobile Phone Network Coverage
Max Input PowerImpedance
Tuning
Polarisation
Height (inc mount)Weight (inc mount)
Gain
Construction
NEXT G and GSM combined825 to 960 MHz and 1710 to 2190 MHz
30 Watts50 Ohms
Factory
Vertical
90 cm0.8 kg
Fibreglass radome, copper radiating elements, aluminium ferrule, delrin adaptor for base
VSWR Less than 1.6:1 across the full band
H-Plane 360O Omnidirectional
Connector An FME female connector is fitted to the cable
Cable 5 metres of RG58 low loss stranded cable side exits from the aluminium ferrule
Radome Colour Specify either a White, Black or Brown radome colour when ordering
Folding Base Supplied
Secure the folding base to any flat surface at any angle using 4 screws or boltsMounting
MM1toughened plastic
MM2stainless steel
MADBSS
1.55 kg90 cm
Factory
30 Watts50 OhmsVertical360O Omnidirectional
6.2 dBi at 825 to 960 MHz3 dBi at 1710 to 2190 MHz
Frequency Bandwidth825 – 960 MHz
1710 - 2190 MHzNEXT G and GSM
combined
CM Series MAX-GAINNEXT G or GSM Mast Mount
Cellular Mobile Phone Antennas
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth825 – 960 MHz NEXT G or GSM
For high gain Data Link applications in either the NEXT G or GSM frequency ranges, these 8.1 dBi omnidirectional mast mount models will be ideal.
The white fibreglass radome and stainless steel mount tube stands 2.4 metres tall. The antenna is matched internally by a unique transforming printed circuit board.
The N-Female connector located at the base of the mount tube is rated for up to 20 watts input power.
CM1600AM Â is factory tuned to cover the NEXT G network, 825 to 890 MHz.
CMG1600AM Â is for the GSM network, 890 to 960 MHz.
All components used are of the highest quality to ensure long term survival in the harshest weather conditions and environments. These antennas will deliver reliable performance for many years.
Mounting clamps, feeder cable, connectors and other accessories are available separately to complete the installation.
EB1SSstainless steel parallel mast
clamps
Construction
SPECIFICATIONS
Frequency Range
Single piece white fibreglass tapered radome, transforming printed circuit board, stainless steel mount tube
NEXT G825 to 890 MHz
CM1600AM
GainMax Input Power
8.1 dBi
Impedance
Polarisation Vertical
20 Watts
Height 2.4 metresWeight 0.7 kg
MAST Mounting Clamps (not supplied)
2 x EB1SS stainless steel parallel clamps recommended.Suit round mast between 20 mm and 50 mm in diameter.
Mount Tube 420 mm long x 20 mm diameter
CMG1600AM
8.1 dBi20 Watts
Tuning Factory
Vertical
0.7 kg
FactoryVSWR < 1.5:1 full band
50 Ohms 50 OhmsDC Grounded Yes Yes
H-Plane 360O Omnidirectional 360O OmnidirectionalConnector N-Female located at base of mount tube
2.4 metres
Blue Cap Red Cap
GSM890 to 960 MHz
E-Plane 13O 13O
< 1.5:1 full band
DLD860Stud Mount Data Link Dipole
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth845 – 875 MHz Full Band
DLD860 is a stud mount dipole for data link purposes factory tuned to cover the full frequency range 840 to 875 MHz with 2.1 dBi gain.
The flexible UV stabilised black PVC radome and delrin ferrule stands 28 cm tall.
The dipole can be secured into any bracket with a 12.7 mm (½”) minimum diameter hole using the stainless steel nut at the base. A variety of mounting brackets are available separately.
No metal ground plane is necessary for the antenna to operate effectively. Potential mount positions therefore include vehicles and numerous fixed locations where no metal exists.
1.8 M of RG316 cable bottom exits through the base.
An SMA Male connector is fitted to the cable. Other connector options are available upon request.
Construction
SPECIFICATIONS DLD900
Flexible UV stabilised black PVC radome and cap with delrin mount ferrule
VSWR
Impedance (Nom.)
Tuning
Polarisation
Cable
Connector
HeightWeight
Mounting
2.1 dBiGain
Less than 1.5:1 across full band
50 Ohms
Factory
Vertical
28 cm50 grams
Frequency Range 845 to 875 MHz full band
20 WattsMaximum Power
DC Grounding Yes
1.8 M of RG316 cable bottom exits through the base
SMA Male fitted to the cable (Other connectors available)
Secure to any bracket with12.7 mm (½") minimum diameter hole using the stainless steel nut at the base
H-Plane 360O Omnidirectional
DLD860
28 cm
1.8 M of RG316 cable bottom exits through the delrin base
Secure to any bracket with a 12.7 mm (½”) minimum diameter holeAn SMA Male connector
is fitted to the cable
DLD900Stud Mount Data Link Dipole
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth900 – 930 MHz Full Band
DLD900 is a stud mount dipole for data link purposes factory tuned to cover the full frequency range 900 to 930 MHz with 2.1 dBi gain.
The flexible UV stabilised black PVC radome and delrin ferrule stands 23 cm tall.
The dipole can be secured into any bracket with a 12.7 mm (½”) minimum diameter hole using the stainless steel nut at the base. A variety of mounting brackets are available separately.
No metal ground plane is necessary for the antenna to operate effectively. Potential mount positions therefore include vehicles and numerous fixed locations where no metal exists.
90 cm of RG174 cable bottom exits through the base.
An SMA Male connector is fitted to the cable. Other connector options are available upon request.
Construction
SPECIFICATIONS DLD900
Flexible UV stabilised black PVC radome and cap with delrin mount ferrule
VSWR
Impedance (Nom.)
Tuning
Polarisation
Cable
Connector
HeightWeight
Mounting
2.1 dBiGain
Less than 1.5:1 across full band
50 Ohms
Factory
Vertical
23 cm50 grams
Frequency Range 900 to 930 MHz full band
20 WattsMaximum Power
DC Grounding Yes
90 cm of RG174 cable bottom exits through the base
SMA Male fitted to the cable (Other connectors available)
Secure to any bracket with12.7 mm (½") minimum diameter hole using the stainless steel nut at the base
H-Plane 360O Omnidirectional
DLD900
23 cm
90 cm of RG174 cable bottom exits through the delrin base
Secure to any bracket with a 12.7 mm (½”) minimum diameter holeAn SMA Male connector
is fitted to the cable
M99BNC900Highly Flexible Whipwith BNC Male Base
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 21 February 2011
Bandwidth900 – 930 MHz Full Band
M99BNC900 is a highly flexible whip factory tuned to cover the full frequency range 900 to 930 MHz.
Constructed from brass and stainless steel with a black UV resistant cover, the antenna stands 19 cm tall and delivers 2.1 dBi gain.
The BNC Male connector at the base fits to any portable or fixed base station data device with a BNC Female connector.
SPECIFICATIONS M99BNC900
Brass, stainless steel, blackUV resistant heatshrink
Less than 1.5:1 full band
2.1 dBi
25 Watts50 Ohms19 cm
900 to 930 MHz full band
Vertical
Factory
BNC Male base fits toBNC Female connectoron data device
Omnidirectional
Construction
VSWR
Gain
Maximum PowerImpedance (Nom)Height
Frequency
Polarisation
Tuning
Mounting
Pattern
SG1885TPMCollinear
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 12 June 2012
Bandwidth1,885 – 1,905 MHz Full Band
The SG1885TPM omnidirectional collinear data link antenna is factory tuned to cover the full frequency range 1,885 to 1,905 MHz. Standing 50 cm tall, the antenna delivers 5.14 dBi gain.
Construction consists of silver soldered internals, a white fibreglass radome and aluminium ferrule.
This sturdy and compact design makes the antenna ideal for external mounting to a mast, building or vehicle.
The stud, nut and washer at the base mounts simply into any bracket with 12.7 mm (½”) minimum diameter hole.
3 metres of RG58 low loss cable side exits from the mount ferrule.
A TNC Male connector is fitted to the cable. Other connectors are available upon request.
A TNC Male crimp connector is fitted to the 3 metre RG58 low loss cable.
Other connector options are available.
Construction
SPECIFICATIONS SG1885TPM
Silver soldered internals, white fibreglass radome, aluminium ferrule
VSWR
Impedance (Nom.)
Tuning
Polarisation
Cable
Connector
HeightWeight
Mounting
5.14 dBiGain
Less than 1.5:1 across full band
50 Ohms
Factory
Vertical
50 cm350 grams
Frequency Range 1,885 to 1,905 MHz full band
10 WattsMaximum Power
DC Grounding Yes
3 metres of RG58 low loss cable side exits from the ferrule
TNC Male connector fitted(Other connectors available)
Secure into any bracket with12.7 mm (½") minimum diameter hole using the stainless steel bolt and washer at the base
H-Plane 360O Omnidirectional
Yagi Y1809DECTDigitally Enhanced Cordless
Telecommunications
Frequency
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 16 May 2012
Bandwidth1880 – 1900 MHz FULL BAND
Y1809DECT is a directional point-to-point Yagi data link mast mount base station antenna specifically designed for Digitally Enhanced Cordless Telecommunications across the frequency range 1,880 to 1,900 MHz.
Constructed from brass and aluminium, this 9 element Yagi delivers 11.3 dBi forward gain. The ultra violet resistant PVC radome protects the internals.
The short RG58 low loss cable tail is terminated with an N-Female connector rated for up to 25 watts input power.
The Yagi may be mounted either horizontal or vertical as the application requires.
U-bolts are supplied for mounting to a mast up to 50 mm in diameter.
Feeder cable, connectors and fittings are all available separately to complete the installation.
For higher gain and power, the Y1809DECT Yagi may be mounted in a stack array formation.
Construction
SPECIFICATIONS Y1809DECT
BandwidthReturn Loss, VSWR
Frequency Range
Brass and aluminium internals enclosed inside an ultra violet resistant white PVC radome. (A black radome is available.)
U-Bolts are supplied for mounting to a round mast up to 50 mm in diameter
GainMaximum Input Power
PolarisationE-PlaneH-Plane
Impedance
Tuning
Cable TailDC Grounding
Connector
Projected AreaWind Load at 160 kph
Length
Weight
Mounting
Width
Number of Elements
Front-to-Back Ratio
11.3 dBi25 Watts
Mount Horizontal or Vertical as required43O
36O
50 Ohms
Yes
DECT 1,880 to 1,900 MHzFull BandBetter than -15 dB, less than 1.5:1Factory
300 mm RG58 low lossN-Female fitted
0.015 m2
1.82 kg
1.5 kg
300 mm80 mm
9
-20 dB
MD2400Stud Mount
ISM Band Collinear
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2010
Bandwidth2.4 – 2.5 GHz Full Band
These ground independent omnidirectional collinear data link antennas cover the full ISM band 2.4 to 2.5 GHz and deliver 2.1 dBi gain. Standing just 23 cm tall, they mount simply into any bracket with 12.7 mm (½") minimum diameter hole.
Construction consists of brass internals, aluminium ferrule and a fibreglass radome. Model MD2400-B has a Black radome and MD2400-W is White.
5 metres of RG58 low loss cable side exits from the aluminium ferrule. An SMA Male connector is fitted to the cable.
The GM1 stainless steel ‘L’ bracket is supplied for mounting. Secure this bracket in position with 2 screws or bolts.
If the SMA Male connector or bracket supplied do not suit your particular application, other options are available upon request.
An SMA Male connector is fitted to the cable
Secure to any bracket with minimum 12.7 mm (½") diameter hole
The GM1 stainless steel ‘L’ bracket with 17 mm diameter hole is supplied
MD2400-W
5 metres of RG58 low loss cable side exits from the ferrule
MD2400-B
23 cm
Construction
SPECIFICATIONS MD2400-B
Brass internals, fibreglass radome, aluminium ferrule
VSWR
Impedance (Nom.)
Tuning
Polarisation
Cable
Connector
HeightWeight
Mounting
2.1 dBiGain
Less than 1.5:1 across full band
50 Ohms
Factory
Vertical
23 cm150 grams
Frequency Range 2.4 to 2.5 GHz full band
10 WattsMaximum Power
DC Grounding Yes
5 metres RG58 low loss cable side exits from the ferrule
SMA Male fitted to the cable (Other connectors available)
Secure into any bracket with minimum 12.7 mm (½") diameter hole using the stainless steel nut and washer at the base.
Mounting Bracket GM1 stainless steel ‘L’ bracket is supplied. (Others available)
Radome Colour Black
MD2400-W
White
SG2400Stud Mount and Flange Mount
ISM Band Collinear
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth2.4 – 2.5 GHz Full Band
These omnidirectional collinear ISM band data link antennas deliver 5.14 dBi gain and are available in either stud mount or flange mount models.
SG2400TPM Â stands 55 cm tall and mounts simply into any bracket with 12.7 mm (½") minimum diameter hole using the stainless steel nut and washer at the base.
SG2400R Â has a PVC flange designed for mounting to the roof, floor or other flat surface using 2 screws. The antenna stands 38 cm tall.
Both models are supplied with 50 cm of RG58 low loss solid core cable and a TNC Male connector fitted as standard.
Construction
SPECIFICATIONS SG2400TPM
Aluminium ferrule
VSWR
Impedance (Nom.)
Tuning
Polarisation
CableConnectorHeightWeight
Mounting
5.14 dBiGain
Less than 1.5:1 across the full band
50 Ohms
Factory
Vertical
55 cm220 grams
Frequency Range 2.4 to 2.5 GHz full band
10 WattsMaximum Power
DC Grounding Yes
50 cm of RG58 low loss cable side exitsTNC Male fitted (Other connectors are available)
Secure into any bracket with 12.7 mm (½") min diameter hole using the stainless steel nut and washer at the base
H-Plane 360O Omnidirectional
Brass silver soldered internals and white fibreglass radomePVC Flange, 10 cm diam
SG2400R
5.14 dBi
50 Ohms
Factory
Vertical
10 Watts
Yes
360O Omnidirectional
38 cm320 grams
Secure the 10 cm diameter PVC flange base to the roof, floor or any flat surface using 2 screws
Connectors other than TNC can be supplied as required.
At data link 2.4 GHz frequencies, it is important to keep feeder cable runs to the shortest length necessary. Where a long run is unavoidable, then a high quality low loss cable such as RU400 should be used.
Z2400-8Mast Mount
ISM Band Collinear
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth2.4 – 2.5 MHz Full Band
Z2400-8 is an omnidirectional collinear mast mount antenna designed for data communications in the 2.4 to 2.5 GHz ISM band. 85 cm tall, the antenna delivers 10 dBi gain.
Construction consists of copper internals, a robust white fibreglass radome and stainless steel mount tube.
An N-Female connector rated for up to 50 watts input power is located at the base of the mount tube.
One UB3SS stainless steel parallel clamp will be ideal for mounting this collinear antenna to a round mast up to 50 mm in diameter.
High quality RU400 low loss 50 ohm feeder cable, connectors and other installation accessories can be supplied as you require.
An N-Female connector is located at the base of the stainless steel mount tube
Construction
SPECIFICATIONS Z2400-8
Copper internals, white fibreglass radome and stainless steel mount tube
VSWR
Impedance (Nom.)
Tuning
Polarisation
CableConnectorHeightWeight
Mounting Clamp(Not Supplied)
10 dBiGain
Less than 1.5:1 across the full band
50 Ohms
Factory
Vertical
85 cm610 grams
Frequency Range 2.4 to 2.5 GHz full band
50 WattsMaximum Power
DC Grounding Yes
None
1 x UB3SS stainless steel parallel clamp is recommended for mounting to a round mast between 20 mm and 50 mm in diameter
H-Plane 360O Omnidirectional
Mount Tube Dimensions
25.4 mm diameter x 17 cm stainless steel
N-Female at base of the mount tube
The UB3SS stainless steel mast clamp is available to order separately.
High quality RU400 low loss feeder cable and N-Male crimp connector to suit are available to complete the installation.
Z2400-8RSMast Mount ISM Band Collinear
with Rear Reflector Screen
Frequency
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 24 November 2011
Bandwidth2.4 – 2.5 MHz Full Band
Z2400-8RS is a collinear mast mount antenna designed for wireless data link applications across the 2.4 to 2.5 GHz ISM band. The reflector screen restricts the radiation pattern emitted at the rear.85 cm tall, the antenna delivers 13 dBi forward gain with the rear screen fited.
The front-to-back ratio is -20 dB.
Construction consists of copper internals, a robust white fibreglass radome, stainless steel mount tube and stainless steel rear reflector screen.
An N-Female connector rated for up to 50 watts input power is located at the base of the mount tube.
Two U-bolts are supplied for mounting the antenna to a round mast between 20 mm and 50 mm in diameter.
Signal loss will be high at ISM band data link frequencies. It is therefore most important to select a good quality low loss feeder cable according to the length of run required. Always keep the cable run to the shortest length necessary.
RU400 low loss is recommended as the minimum standard of feeder cable necessary to reduce signal loss and maintain optimum antenna performance.
Connectors and other installation accessories can be supplied as you require.
High quality RU400 low loss feeder cable and N-Male crimp connector to suit are available to complete the installation.
Construction
SPECIFICATIONS Z2400-8RS
Copper internals, white fibreglass radome, stainless steel mount tube, stainless steel rear reflector screen
VSWR
Impedance (Nom.)
Tuning
Polarisation
CableConnectorDimensionsWeight
Mounting
13 dBi with rear screen fittedGain
Less than 1.5:1 across the full band
50 Ohms
Factory
Vertical
85 cm high x 15 cm wide1.25 kg
Frequency Range 2.4 – 2.5 GHz full band
50 WattsMaximum Power
DC Grounding Yes
None
2 x U-Bolts are supplied to suit a round mast between 20 mm and 50 mm in diameter
Front-to-Back Ratio -20 dB
N-Female at base of the mount tube
E-Plane 170O
H-Plane 17O
Vertical E-Plane Radiation Patternat 2.4 GHz
DLD2400Stud Mount Data Link Dipole
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth2.4 GHz n/a
DLD2400 is a stud mount dipole factory tuned for 2.4 GHz with 2.1 dBi gain. The flexible UV stabilised black PVC radome and delrin ferrule stands just 11.5 cm tall.
The antenna can be secured into any bracket with a 12.7 mm (½”) minimum diameter hole using the stainless steel nut at the base. A variety of mounting brackets are available separately.
No metal ground plane is necessary for the antenna to operate effectively. Potential mount positions therefore include vehicles and numerous fixed locations where no metal exists.
60 cm of RG174 cable bottom exits through the base.
An SMA Male connector is fitted to the cable. Other connector options are available upon request.
DLD2400
11.5 cm
60 cm of RG174 cable bottom exits through the delrin base
Secure to any bracket with a 12.7 mm (½”) minimum diameter hole
An SMA Male connector is fitted to the cable
Construction
SPECIFICATIONS DLD2400
Flexible UV stabilised black PVC radome and cap with delrin mount ferrule
VSWR
Impedance (Nom.)
Tuning
Polarisation
Cable
Connector
HeightWeight
Mounting
2.1 dBiGain
< 1.5:1
50 Ohms
Factory
Vertical
11.5 cm40 grams
Frequency 2.4 GHz
20 WattsMaximum Power
DC Grounding Yes
60 cm of RG174 cable bottom exits through the base
SMA Male fitted to the cable (Other connectors available)
Secure to any bracket with12.7 mm (½") minimum diameter hole using the stainless steel nut at the base
H-Plane 360O Omnidirectional
WH2400Data Link Whip
with SMA Male Connector
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth2.4 GHz n/a
WH2400 is a small whip just 54 mm tall designed for internal use on data link devices operating at 2.4 GHz.
The antenna fits on to the data device using the SMA Male connector inside the base.
SPECIFICATIONS WH2400
Brass and Black UV resistant PVC
< 1.5:1
2.1 dBi
5 Watts50 OhmsSMA Male inside base54 mm9 grams
2.4 GHz
Vertical
Factory
Construction
VSWR
Gain
Maximum PowerImpedance (Nom)ConnectorHeightWeight
Frequency
Polarisation
Tuning
CP2400-15Right-Hand Circularly Polarised
End Fired Point-To Point ISM Band
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth2.4 – 2.5 GHz Full Band
CP2400-15 is a directional right-hand circularly polarised end fired helical antenna specifically designed for point-to-point data communications across the 2.4 to 2.5 GHz ISM Band.
Circularly polarised antenna systems inherently cancel out unwanted reflections making this model the preferred choice for 2.4 GHz ISM band data transmissions.
Construction features copper internals and a unique reduced size ground plane. This allows all elements to be enclosed inside a compact white fibreglass radome providing low wind loading.
1.12 metres long, the antenna delivers 17.1 dBi gain. The N-Female connector located at the base of the high quality stainless steel mount tube is rated for up to 50 watts input power.
The UB2SS stainless steel right-angle clamp is recommended for mounting.
E-Plane
H-Plane
Important Installation Note
The CP2400-15 antenna has 2 drain holes in the fibreglass radome.
It is important to ensure these drain holes are facing downward upon installation.
SPECIFICATIONS CP2400-15
Copper internals, white fibreglass radome, stainless steel mount tube
< 2 dB
Less than 1.5:1 across the full band
17.1 dBi50 Watts50 Ohms
15 dB
N-Female at base of the mount tube1.12 metres1.5 kg
1 x UB2SS stainless steel right-angle clamp is recommended for mounting to a mast between 20 mm and 50 mm in diameter
50 mm diameter x 220 mm
2.4 to 2.5 GHz full band
Right-Hand CircularFactory
Yes
19 degrees
Construction
VSWR
GainMaximum PowerImpedance (Nom)
Front-to-Back Ratio
ConnectorOverall LengthWeight
Mounting Clamp(Not Supplied)
Circularity
Mount Tube Dimensions
Frequency
PolarisationTuning
DC Grounding
E-PlaneH-Plane 17 degrees
Y2400-9 and Y2400-18Yagi Directional Point-to-Point
Mast Mount
Frequency
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 8 May 2012
Bandwidth2.4 GHz n/a
These Yagi mast mount antennas are designed for directional point-to-point 2.4 GHz data link transmit and receive applications. Constructed from brass and aluminium, the ultra violet resistant PVC radome protects the internal elements.
 Y2400-9 has 9 elements and delivers 11.3 dBi forward gain.  Y2400-18 is the high gain 17.8 dBi model with 18 elements.
The short RG58 low loss cable tail is terminated with an N-Female connector rated for up to 25 watts input power.
These Yagi’s can be mounted either horizontal or vertical as the application requires. For higher gain and power, mount antennas in a stack array formation.
U-bolts are supplied for mounting to a mast up to 50 mm in diameter. Coaxial feeder cable, connectors and fittings are all available separately to complete the installation.
Construction
SPECIFICATIONS Y2400-9
Return Loss, VSWRFrequency Range
Brass and aluminium internals enclosed inside an ultra violet resistant white PVC radome. (A black radome is available.)
U-Bolts are supplied for mounting to a round mast up to 50 mm in diameter
GainMaximum Input Power
PolarisationE-PlaneH-Plane
Impedance
Tuning
Cable TailDC Grounding
Connector
Projected AreaWind Load at 160 kph
Length
Weight
Mounting
Width
Number of Elements
Front-to-Back Ratio
11.3 dBi25 Watts
Mount Horizontal or Vertical as required50 Ohms
2.4 GHzBetter than -15 dB, less than 1.5:1Factory9
43O
36O
YesRG58 low loss cable tail 200 mm longN-Female fitted
0.015 m2
1.82 kg
1.5 kg
300 mm80 mm
-20 dB
Y2400-18
2.4 GHz
17.8 dBi25 Watts50 Ohms
18
26O
23O
Yes-20 dB
N-Female fitted
0.035 m2
4.26 kg
2.0 kg
700 mm80 mm
Stack Array Spacing
173 mm apartHorizontalVertical 145 mm apart
277 mm apart245 mm apart
Factory
Y2400-9
Y2400-9
Y2400-18
Y2650-9 and Y2650-18Yagi Directional Point-to-Point
Mast Mount
Frequency
ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 8 May 2012
Bandwidth2.65 GHz n/a
These Yagi mast mount antennas are designed for directional point-to-point 2.65 GHz data link transmit and receive applications. Constructed from brass and aluminium, the ultra violet resistant PVC radome protects the internal elements.
 Y2650-9 has 9 elements and delivers 11.3 dBi forward gain.  Y2650-18 is the high gain 17.8 dBi model with 18 elements.
The short RG58 low loss cable tail is terminated with an N-Female connector rated for up to 25 watts input power.
These Yagi’s can be mounted either horizontal or vertical as the application requires. For higher gain and power, mount antennas in a stack array formation.
U-bolts are supplied for mounting to a mast up to 50 mm in diameter. Coaxial feeder cable, connectors and fittings are all available separately to complete the installation.
Construction
SPECIFICATIONS Y2650-9
Return Loss, VSWRFrequency Range
Brass and aluminium internals enclosed inside an ultra violet resistant white PVC radome. (A black radome is available.)
U-Bolts are supplied for mounting to a round mast up to 50 mm in diameter
GainMaximum Input Power
PolarisationE-PlaneH-Plane
Impedance
Tuning
Cable TailDC Grounding
Connector
Projected AreaWind Load at 160 kph
Length
Weight
Mounting
Width
Number of Elements
Front-to-Back Ratio
11.3 dBi25 Watts
Mount Horizontal or Vertical as required50 Ohms
2.65 GHzBetter than -15 dB, less than 1.5:1Factory9
43O
36O
YesRG58 low loss cable tail 200 mm longN-Female fitted
0.015 m2
1.82 kg
1.5 kg
300 mm80 mm
-20 dB
Y2650-18
2.65 GHz
17.8 dBi25 Watts50 Ohms
18
26O
23O
Yes-20 dB
N-Female fitted
0.035 m2
4.26 kg
2.0 kg
700 mm80 mm
Stack Array Spacing
173 mm apartHorizontalVertical 145 mm apart
277 mm apart245 mm apart
Factory
Y2650-9
Y2650-9
Y2650-18
A helically wound right-hand circularly polarised antenna will reduce unwanted signal interference and reflections. The “end fired” design is particularly well suited for point-to-point data communications, whether that be cordless phone, Wi-Fi or wireless broadband. This CP5800-15 model is factory tuned for 5.7 to 5.85 GHz and delivers high 14 dBi gain with a narrow beamwidth.
CP5800-15 is suitable for use in the high frequency ISM and RFID Radio Frequency Identification bands.
The antenna is fully enclosed within a fiberglass radome and protected from the meteorological influences which can affect some high frequency helical antennas.
Measuring just 180 mm in length, wind loading is minimal.
The N-female connector fitted to the 200 mm RG142 cable tail is rated for up to 100 watts input power.
A U-bolt and Vee-block is supplied for mounting the antenna to a round mast up to 50 mm in diameter. An offset clamp assembly to suit a 60 mm diameter mast can be supplied upon request.
Coaxial feeder cable, connectors and fittings are all available separately to complete the installation.
CP5800-15Right-Hand Circularly Polarised
End Fired Point-To-Point
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth5.7 – 5.85 GHz Full Band
SPECIFICATIONS CP5800-15
Copper helix with brass and copper matching section, white fibreglass radome, aluminium mounting plate
< 2 dB
Less than 1.5:1 across the full band
14 dBi100 Watts50 Ohms
20 dB
200 mm of RG142
180 mm500 grams
U-bolt and Vee-block supplied to suit round mast up to 50 mm in diameter.Offset clamp assembly to suit 60 mm diameter mast available upon request.
5.7 to 5.85 GHz full band
Right-Hand CircularFactory
Yes
20 degrees
Construction
VSWR
GainMaximum PowerImpedance
Front-to-Back Ratio
Cable Tail
Overall LengthWeight
Mounting
Circularity
Frequency Range
PolarisationTuning
DC Grounding
E-PlaneH-Plane 18 degrees
Connector N-female fitted to the cable tail
0.008 m2
0.909 kg, 0.009 kNProjected AreaWind Loading at 160 kph
PD-240N22-Way N-Type WiMAX Power Divider
Frequency
ZCG Scalar, Head Office, 1 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]
DATA LINKANTENNAS
Section 7
Updated 22 February 2011
Bandwidth2.4 – 2.5 GHz Full Band
PD-240N2 is a power divider for combining the output of two WiMAX data link antennas operating in the frequency range 2.4 to 2.5 GHz.
Constructed from alumium, brass and stainless steel, this power divider will maintain return loss to better than -20 dB, less than 1.2:1 VSWR across the full band.
The N-Type Female connectors are rated for up to 250 watts power.
The power divider can be secured to a bracket using the M8 mounting bolt and washer provided.
Construction
SPECIFICATIONS PD-240N2
Brass, aluminium and stainless steel
Maximum PowerImpedance
Frequency Range
250 Watts50 Ohms
2.4 to 2.5 GHz full band
Return Loss,VSWR
Better than -20 dB,< 1.2:1 across full band
Input Connector 1 x N-Female
Dimensions 80 mm long x 50 mm wide
MountingTo any bracket using the M8 bolt and washer provided
Output Connectors 2 x N-Female
Weight 200 grams