ddec master 2000 current4-6

Detroit DieselElectronic Controls

DDECDDECDDEC

DDECDDEC IVIII

25ST0072-2 Rev. 04/4/00 3

DDEC AGENDA

• Pre-Test• Objectives• Review Manuals• Features & Components• System Hardware• Repair Tools• Basic Electricity• Trouble Shooting• DDEC Reprogramming• Post-Test, Evaluations

25ST0072-2 Rev. 04/4/00 4

DDEC History

• DDEC I Introduced in 1985 on 92 Series• Series 60 Introduced in 1987 As the First Engine

Ever Designed Exclusively for Electronic Controls• DDEC II Introduced in 1987• DDEC III Introduced April, 1993• DDEC III Full Production January, 1994• DDEC IV Initial Release, August, 1997• DDEC IV Full Production, January, 1998

25ST0072-2 Rev. 04/4/00 5

What is DDEC?

An advanced electronic fuel injection control system that can be integrated into many applications

DDEC Consists of:• Sensors and switches• Conductors and connections• ECM (computer)

– Hardware– Software

• Injectors

25ST0072-2 Rev. 04/4/00 7

Electronic Engine Advantages

• Engine Protection

• Engine Diagnostics

• Reduced Maintenance

• Improved Engine Governing

• Fuel Economy Optimization

• Enhanced Cold Starting

• Smoke Control

• Reduced Emission Levels

25ST0072-2 Rev. 04/4/00 9

DDEC IV Features

• Four New ECM’sECM Description

Standard Truck 6 Cylinder 12 Volt

Universal 8 Cylinder 12/24 VoltS4000 8 Cylinder 12/24 Volt

Natural Gas 8 Cylinder 12/24 Volt

• Increased Memory - 57% Over DDEC III• Faster Processing Time - 50% Over DDEC III• J1939 Communication Link - Standard• Battery Backed Real Time Clock & Calendar• DDEC Data (Enhanced ECM Data Pages) -

Standard

25ST0072-2 Rev. 04/4/00 10

DDEC Necessities

Ignition

ElectronicControlModule(ECM)


EEPROMEEPROM

+-Battery

Timing Reference

Synch Reference

EUIEUI

25ST0072-2 Rev. 04/4/00 11

Schematic Diagram DDEC III/ IV



EEPROMEEPROM

25ST0072-2 Rev. 04/4/00 12

Electronic Control Module

25ST0072-2 Rev. 04/4/00 13

Electronic Control Module

DDC responsibility

Engine sensors, harness, & connectors

Injector harness & connectorsInjectors

OEM responsibility

Mandatory circuits Power and Ground

J1922,J1939, Ignition

Throttle position sensorOptional circuits Manual fan on switch, Jake Brake, 439 Ignition wire

25ST0072-2 Rev. 04/4/00 14

Schematic Diagram DDEC III / IV



EEPROMEEPROM

+-BatteryBattery

25ST0072-2 Rev. 04/4/00 15

Power Supply

• DDEC II - 12 Volt• DDEC III - 12/24 Volt• DDEC IV- 12 or 24 Volt• Source must be Isolated from any other Vehicle Accessory• The ECM Power Source must be Fused with the Proper Amp• The ECM Must Be Incorporated with a 5 Amp Fuse on the

440 wire going into the 439 wire.• The ECM Case Must be Electrically Isolated from any

Chassis Ground

25ST0072-2 Rev. 04/4/00 16

Power Supply DDEC III/ IV

25ST0072-2 Rev. 04/4/00 17

Power Supply DDEC III / IV

25ST0072-2 Rev. 04/4/00 18




EEPROMEEPROM

+-BatteryBattery

EUIEUI

25ST0072-2 Rev. 04/4/00 19

Electronic Unit Injectors

Series 71/92 EUI Series 149 EUI Series 50/60 EUI

Series 4000 Spray Nozzle Series 2000 EUP

Series 53 EUI

Series 50/60 Injector

Animation

Fuel out

Fuel in

Voltage in

Solenoid

Plunger

Poppet Valve

Needle Valve

Rocker Arm

Cam

Series 4000 Nozzle

AnimationCAM

Rocker ArmSolenoid

filter

Fuel Return

High Pressure

Fuel

Needle Valve

Nozzle

Series 2000 EUP

AnimationCAM

Rocker Arm

Solenoid

EUP

Cam

Spay Nozzle

Fuel In

25ST0072-2 Rev. 04/4/00 23

Electronic Unit Pump

25ST0072-2 Rev. 04/4/00 24

Top Of Stroke

InjectorTip

FuelIn

FuelOut

25ST0072-2 Rev. 04/4/00 25

Start Of Injection

InjectorTip

FuelIn

FuelOut

25ST0072-2 Rev. 04/4/00 26

End Of Injection

InjectorTip

FuelIn

FuelOut

25ST0072-2 Rev. 04/4/00 27

Injection Sequence

InjectorTip

FuelIn

FuelOut

InjectorTip

FuelIn

FuelOut

InjectorTip

FuelIn

FuelOut

25ST0072-2 Rev. 04/4/00 28

Injector Calibration Codes

• DDEC II No Calibration Codes• DDEC III/ IV Calibration Codes From 00-99

Calibration Code

Part Number

25ST0072-2 Rev. 04/4/00 29

Injector Cycle Terminology

IRT Injector Response Time - Length of Time (ms) required to close the Control Valve

PW Pulse Width - Degrees of Crankshaft Rotation when Fuel is Injected

25ST0072-2 Rev. 04/4/00 30

Injector Response Times

25ST0072-2 Rev. 04/4/00 31

Cylinder Cut-Out

25ST0072-2 Rev. 04/4/00 32

Injection Cycle

BOE BOI EOE EOI

IRT

Time

PW

(Inflection Point)

BAT

Voltage0V

V_REG, 5V

Current0A

ClosedOpen

Control Valve Lift

Injection Rate

25ST0072-2 Rev. 04/4/00 34

Sensor Operations

Operates on 5 Volts for All D.C. Sensors

.25 4.75

NormalOperating

Range

Low Voltage

0 5

High Voltage

25ST0072-2 Rev. 04/4/00 35

Sensor Wiring

• Common Return Circuit. #452• Thermistor

• Piezoresistive Pressure sensor

• Voltage is Proportional to Pressure

25ST0072-2 Rev. 04/4/00 36

2-wire Sensors

5V Supply

Signal

Return

ECM Sensor

Open = HI VOLTAGE

Short = LO VOLTAGE

25ST0072-2 Rev. 04/4/00 37

3-wire Sensors

ECM Sensor5V Supply

Signal

Return

Open Supply = LO VOLTAGEOpen Signal = LO VOLTAGE Open Return = HI VOLTAGE

HI VOLTAGESupply short to Signal =Supply short to Return = LO VOLTAGESignal short to Return = LO VOLTAGE

25ST0072-2 Rev. 04/4/00 38

SRS/TRS Sensors

• SRS/TRS: Magnetic pickup sensors generate alternating current (A.C.). The frequency will change dependent on the speed of the pulse wheel (RPM of engine).

25ST0072-2 Rev. 04/4/00 39



EEPROMEEPROM

++--Battery

Timing Reference

Synch Reference


EUIEUI

25ST0072-2 Rev. 04/4/00 41

Series 50/60SRS/TRS Sensors

SRS/TRS

Timing WheelDDEC III/ IV

Bull GearDDEC III/ IV

Series 60 Sensor

Locations

25ST0072-2 Rev. 04/4/00 43

Series 2000SRS/TRS Sensors

SRS/TRS

Cam Gear/SRS

TIMING WHEEL

TIMING WHEEL

Series 2000 Sensor

Locations

25ST0072-2 Rev. 04/4/00 45

Series 4000SRS/TRS Sensors

SRS/TRS

Cam Gear/SRS

Timing Wheels

Series 4000 Sensor

Locations

25ST0072-2 Rev. 04/4/00 47

Two Cycle SRS/TRS with Timing Wheel

SRS/TRSSensor

Series 71 Series 92 / 6V, 8V, 12V-71

SRS/TRSSensor

Timing Wheel& Cam Pulley

Timing Wheel& Cam Pulley

25ST0072-2 Rev. 04/4/00 48

Two Cycle SRS/TRS with Timing Wheel

SRS/TRSSensors

TimingWheels

TimingWheels

Series 92, 12V, 16V

SRS/TRSSensors

Series 149

25ST0072-2 Rev. 04/4/00 49

Series 53 SRS/TRS with Timing Wheel

SRS/TRSSensors

TimingWheel

SRS PIN

25ST0072-2 Rev. 04/4/00 50

Schematic Diagram DDEC IV



EEPROMEEPROM

Timing Reference

Synch Reference

Electronic FootPedal Assembly

EUIEUI

+-Battery

25ST0072-2 Rev. 04/4/00 51

Throttle Position SensorElectronic Foot Pedal Assembly

• 5 volt, three wire circuit

• Electronic Foot Pedal Assembly signals throttle position for the Limiting Speed Governor.

• Optional idle validation switch insures that the engine will remain at idle in the event of a TPS circuit failure

25ST0072-2 Rev. 04/4/00 53

Schematic Diagram DDEC IV



EEPROMEEPROM

Turbo Boost Pressure

Timing Reference

Synch Reference


EUIEUI

+-Battery

25ST0072-2 Rev. 04/4/00 54

Turbo Boost Sensor

DDEC III Series 50/60/2-Cycle

Series 2000 / 4000 Series 50/60 DDEC IV

Series 53

25ST0072-2 Rev. 04/4/00 55




EEPROMEEPROM

+-BatteryBattery

Fuel / Oil / Coolant/ AirTemperature


Timing Reference

Synch Reference


EUIEUI

25ST0072-2 Rev. 04/4/00 56

Temperature Sensors

Coolant Temperature SensorSeries 50/60

Air Temperature SensorSeries 50/60

Fuel/Oil/Coolant Temperature SensorSeries 50/60/2-Cycle - Air Temp 53

Fuel/Oil/Coolant Temperature SensorSeries 2000/4000

25ST0072-2 Rev. 04/4/00 58




EEPROMEEPROM

++--BatteryBattery

Fuel / Oil / CoolantTemperature


Timing Reference

Synch Reference


Oil / Fuel Pressure

EUIEUI

25ST0072-2 Rev. 04/4/00 59

Pressure Sensors

Series 50/60/2-Cycle

Series 2000/4000

Series 2000/4000Different Harness Connectors

CoolantPressure

Oil / FuelPressure

Series 4000 High Pressure Fuel

25ST0072-2 Rev. 04/4/00 60




EEPROMEEPROM

++--BatteryBattery

Oil / Fuel Pressure



Timing Reference

Synch Reference


Oil level/Fuel Restriction

EUIEUI

25ST0072-2 Rev. 04/4/00 61

On Engine Components

• Oil Level Sensor– Mounts in Front Sump Non-

metal Oil Pan– Utilizes Optical Technology to

"See" Oil Level– Engine Must Be Off (Zero

RPM ) for "X" Minutes (Based on Oil Temp.) to Drain Oil Back to the Pan

– Switches at Four Quart Low Level

– OEM Impact» Order Maintenance Alert

System on the Engine

25ST0072-2 Rev. 04/4/00 62


• Fuel Restriction Sensor– Measures Fuel System

Restriction at Fuel Pump Inlet– Sensor Measures Actual Inlet

Restriction – OEM Impact

» Order Maintenance Alert System on the Engine

25ST0072-2 Rev. 04/4/00 63




EEPROMEEPROM

+-BatteryBattery

Oil / Fuel Pressure



Coolant Level

Timing Reference

Synch Reference



EUIEUI

25ST0072-2 Rev. 04/4/00 64

Coolant Level Sensor

DDEC III or IVCoolant Level Sensor

DDEC II/ III Coolant Level Sensor

25ST0072-2 Rev. 04/4/00 65




EEPROMEEPROM

+-BatteryBattery

Oil / Fuel Pressure



Coolant Level

Timing Reference

Synch Reference

VSG Control



EUIEUI

25ST0072-2 Rev. 04/4/00 66

VSG Control

• Variable Speed Governor– Throttle Position Controls RPM

• Droop– Difference in RPM Between Full Load

(Rated Speed) and Maximum Engine RPM (No Load)

– Allows the engine to overrun the rated or governed engine speed.

25ST0072-2 Rev. 04/4/00 67




EEPROMEEPROM

+-BatteryBattery

Oil / Fuel Pressure



Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive Shift


EUIEUI

25ST0072-2 Rev. 04/4/00 68

Progressive Shift

• Use Spec Manager to determine values to program for Progressive Shift

• Example

Low Gear #1 off 12 Max MPH LimitLow Gear #1 limit 1400Low Gear #1 max 1800Low Gear #2 off 27 Max MPH LimitLow Gear #2 limit 1600Low Gear #2 max 1800High Gear on 50 Max MPH LimitHigh Gear max 1700

25ST0072-2 Rev. 04/4/00 69

Progressive Shift

25ST0072-2 Rev. 04/4/00 70




EEPROMEEPROM

+-BatteryBattery

Oil / Fuel Pressure



Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive ShiftPressure Governor


EUIEUI

25ST0072-2 Rev. 04/4/00 71

Pressure Governor

Mastermind

Fire Commander

High PressureSensor

•Fire Commander and Mastermind use the same digital inputs and outputs as cruise control

25ST0072-2 Rev. 04/4/00 74

Electronic Fire Commander

Engine Data

System Status

Message Window

Control Buttons

25ST0072-2 Rev. 04/4/00 75




EEPROMEEPROM

+-BatteryBattery

Oil / Fuel Pressure



Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive ShiftPressure Governor

DiagnosticRequest

Stop EngineOverride


EUIEUI

25ST0072-2 Rev. 04/4/00 76

Diagnostic Requestor Stop Engine Override

25ST0072-2 Rev. 04/4/00 78

Engine Protection

• Warning- Illumination of CEL,SEL only

• Rampdown- Immediate reduction to 70% power, ramping down to 40% over 30 seconds and maintains 40% power.

• Shutdown- Same as rampdown except engine is shutdown at the end of 30 seconds.

25ST0072-2 Rev. 04/4/00 79




EEPROMEEPROM

+-BatteryBattery

Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive Shift

DiagnosticRequest

Stop EngineOverride

Engine Rating / Cruise Power / Switch Power


EUIEUI

25ST0072-2 Rev. 04/4/00 80

Multiple Horsepower Ratings

• Three Independent Ratings• One Dependent Cruise Power Rating

• Switch Power Options (C&I)– Max. Power for Fully Loaded Engine– Min. Power for a Lightly Loaded Engine

25ST0072-2 Rev. 04/4/00 81




EEPROMEEPROM

+-BatteryBattery

Cruise Control Vehicle Speed LimitingVehicle Speed Sensor

Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive Shift

DiagnosticRequest

Stop EngineOverride



EUIEUI

25ST0072-2 Rev. 04/4/00 82

Cruise Control

• Determined by vehicle speed (VSS) or engine speed (RPM) DDEC IV changed

• Must be above 20 MPH or 1100 RPM to set• Cruise Power can provide higher HP while in cruise

control by using the C. P. rating.• Uses up to 5 digital inputs and one digital output • VSG can be controlled by the cruise switch• Use cruise switches to set PTO high idle and lower

high idle. You use a step up or step down & step up by pressing or toggling the resume switch.

25ST0072-2 Rev. 04/4/00 83

Vehicle Speed Sensor

• Revs per MileHigh Gear RatioRear End RatioSensor Type (Magnetic)# of teeth on Pulse Wheel

• Vehicle Speed Limit• Vehicle Overspeed with Fuel (typically set 3-4 mph above

road speed limit)• Vehicle Overspeed without Fuel (typically set 5-6 mph above

road speed limit)• VSS Antitamper

– Will not go above Idle– Code will be logged

25ST0072-2 Rev. 04/4/00 84

Cruise Control

25ST0072-2 Rev. 04/4/00 85




EEPROMEEPROM

+-BatteryBattery


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive Shift

DiagnosticRequest

Stop EngineOverride



EUIEUI

Crankcase Pressure

25ST0072-2 Rev. 04/4/00 86

Crankcase Pressure

Series 149 CCM Series 4000 CCPS Series 60 CCM

25ST0072-2 Rev. 04/4/00 87




EEPROMEEPROM

+-BatteryBattery


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive Shift

DiagnosticRequest

Stop EngineOverride



Crankcase Pressure

EUIEUI

CheckEngine

StopEngine

25ST0072-2 Rev. 04/4/00 88

Stop Engine / Check Engine Lights

25ST0072-2 Rev. 04/4/00 89




EEPROMEEPROM

+-BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control


Progressive Shift

DiagnosticRequest

Stop EngineOverride



Crankcase Pressure

EUIEUI

PWM Ports

25ST0072-2 Rev. 04/4/00 90

Pulse Width Modulated Outputs

• 50 Hz duty cycle modulated• Four ports available-- circuits 908, 909, 910, 911• Factory programmed only

1 Hz

50%20%

1 Hz

80%

1 Hz

Signal LowSignal High

• Signals sent by the ECM to other microprocessor controlled systems

25ST0072-2 Rev. 04/4/00 91

PWM

Circuit Wire

No. Color• PWM #1 Output - VIH (Transmission) 908 White• PWM #2 Output - ESH (Throttle/GAS) 909 Lt. Green• PWM #3 Output - ESH (Gas Valve/GAS) 910 Orange• PWM #4 Output - ESH (Fan Control) 911 Pink

• ESH = Engine Sensor Harness• VIH = Vehicle Sensor Harness

25ST0072-2 Rev. 04/4/00 92




EEPROMEEPROM

+-BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride



Crankcase Pressure

EUIEUI

DDR Interface/ DDDL/ Reprogramming

25ST0072-2 Rev. 04/4/00 93

DDR Interface with MPSI Printer

SAE Standards

25ST0072-2 Rev. 04/4/00 95

SAE Standards

•MIDs

•PIDs

•FMIs

•SIDs

25ST0072-2 Rev. 04/4/00 96

SAE Code Format

• PID - Parameter Identifier (can be measured)• SID - System Identifier (cannot be measured)• FMI - Failure Mode Identifier

Example

PID 100 FMI 0 - Parameter High 1 - Parameter Low3 - Circuit High (HI VOLT)4 - Circuit Low (LO VOLT)Oil Pressure

25ST0072-2 Rev. 04/4/00 97

Detroit Diesel Diagnostic Link

25ST0072-2 Rev. 04/4/00 98

DDDL Information

• New PC based DDEC service tool– Release 1.X

» Windows 3.1» PC-486, 33 MHz, 8MB RAM» Support Features up to DDEC III, R5.0

– Release 2.X» Windows 95 (98 2.11)» PC-486, 66MHz, 16MB RAM» Supports all DDEC Systems» Support Data Extractions & Trip Reporting Features

– Release 3.X» Windows 95/98» VGA color monitor» PC-486, 66MHz, 16MB RAM» Supports all DDEC Systems» Support Data Extractions & Trip Reporting Features

25ST0072-2 Rev. 04/4/00 99


25ST0072-2 Rev. 04/4/00 100


25ST0072-2 Rev. 04/4/00 101


25ST0072-2 Rev. 04/4/00 102

DDR Communication- On Highway

DDEC III/ IV6-Pin

DDEC II or III12-Pin

25ST0072-2 Rev. 04/4/00 103

DDR Communication- On Highway

DDEC IV

9 Pin

DDEC II / III / IV Reprogramming

25ST0072-2 Rev. 04/4/00 105

Reprogramming Station

25ST0072-2 Rev. 04/4/00 106

Software

• Software is programmable• Numbered like computer software

– Major version changes number before dot ( X.00 )– Minor version changes number after dot ( 9.XX )

• DDEC III software will be 19.XX or lower– Current DDEC III software is 9.00

• DDEC IV software will be 20.00 or higher– Current DDEC IV software is 28.00

• Software level can ONLY go UP, it can NEVER go back down

25ST0072-2 Rev. 04/4/00 107

Reprogramming StationWindows Based for Download

25ST0072-2 Rev. 04/4/00 108


25ST0072-2 Rev. 04/4/00 109


25ST0072-2 Rev. 04/4/00 112




EEPROMEEPROM

++--BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride



Crankcase Pressure

EUIEUI


Communication

25ST0072-2 Rev. 04/4/00 113

Communication

• J1587– 9600 Baud Rate, used to transmit sensor and engine data

(electronic dash display, vehicle management systems and electronic transmissions). MPSI readers, DDDL

• J1922– 9600 Baud Rate, controls Transmissions, braking

systems and retarders • J1939

– 250k Baud Rate, controls Transmissions, braking systems and retarders also used as the property data link in multi ECM engines

25ST0072-2 Rev. 04/4/00 114




EEPROMEEPROM

++--BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride


Idle Shut Down/Vehicle Power Down


Crankcase Pressure

EUIEUI


Communication

25ST0072-2 Rev. 04/4/00 115

Idle Shut Down (ISD)/ Vehicle Power Shutdown

• Idle Shut Down (ISD): Turns engine off after programmed idle time has elapsed (optional “override” disables idle timer if the engine speed is increased by 100 during last 90 seconds of ISD sequence. The check engine light (CEL) will flash during this 90 seconds.

• Vehicle Power Shutdown relay (optional/OEM) turns off electrical power to the vehicle as well as stopping the engine

2 - 100 Minutes

25ST0072-2 Rev. 04/4/00 116

Vehicle Power Shutdown

To Vehicle

Ignition OnIdle ShutdownIgnition switch

ECM

25ST0072-2 Rev. 04/4/00 117




EEPROMEEPROM

++--BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride




Crankcase Pressure

EUIEUI


Communication

Engine Brake

25ST0072-2 Rev. 04/4/00 118

DDEC III/IVEngine Brakes

• DDEC III/IV controls engine brake operation• If configured for “cruise control engine brake”

the ECM will automatically turn on the brake if the set speed is exceeded.

• Two digital inputs and two ‘positive’ outputs are used to control the brake.

25ST0072-2 Rev. 04/4/00 120

Engine Brakes

• Must be at least 150 rpm above idle speedClutch Released input must be ON/GNDECM must see 0% throttle

Range Example• Cruise Engine Brake Yes/No Yes

Engine Brake MPH 1-10 3 Engine Brake Increment 0-4 2

• Engine Brake/Service Brake Yes/No Yes• Engine Brake Min MPH 0-VSL 35

DDEC Engine Brakes

ECM

S3

T3

#953 (Battery Negative)

Brake Off LO On

Low

Med.

Low

Med.

MEDHIGH

25ST0072-2 Rev. 04/4/00 122




EEPROMEEPROM

++--BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride




Crankcase Pressure

EUIEUI


Communication

Engine BrakeFan Controls

25ST0072-2 Rev. 04/4/00 123

Fan Control

• Four fan configurations can be used– Single fan– Dual fans– Two speed fan– Variable speed fan (PWM) # 4 Hydraulically

Operated (Bus)• Fan controlled by digital output(s)• “Fan override” & “air conditioning active” digital

inputs can force the fan on • Series 4000 uses (PWM) #2 To Operate a Rockford Fan

25ST0072-2 Rev. 04/4/00 124

Fan Control

• Conditions which activate the fan;– High Oil, Coolant, or Air Temp– Circuit fault codes (HI VOLT, LO VOLT) on any of

these three sensors– AC input– Fan Override input– Dynamic Braking (Fan is Activated During Engine

Overspeed to Help Slow The Vehicle)

DDEC Fan Controls

ECM

Temp sensorInputs

Air Supply

Ign. +

Output“off”

Fan “on”

Optional Fan # 2

#953 (-)

Fan Override (Input Off)

Aux. Fan Control (Input On) Air Conditioning - off

Temp sensorInputs

High Temperatures Turn Fan OnNormal Temperatures Allow Fan Off

Output“on”

Fan “off”

Aux. Fan Control (Input Off)Air Conditioning - On(Fan on for at least 3 minutes)

Output“off”

“on”

25ST0072-2 Rev. 04/4/00 129




EEPROMEEPROM

+-BatteryBattery

StopEngine

CheckEngine


Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride



Crankcase Pressure

EUIEUI


Communication

ISD / VehiclePower Down

Engine Brake

Fan ControlsOptimized Idle

25ST0072-2 Rev. 04/4/00 130

Optimized Idle

• Automatic Starting and Stopping of the Engine• Maintains Engine Temperature and / or Battery

Voltage• Optional Sleeper Thermostat• Truck Skin Temperature Sensor is used for

continuous run• Saves Fuel by Running the Engine Only When

Needed• Warm Engines Start Much Easier With Less Exhaust

Emissions

25ST0072-2 Rev. 04/4/00 131

Requirements for Optimized Idle

Cruise Enable Switch Idle Shutdown Enabled Vehicle Power Down

Relay Op Idle light on dash Park Brake Switch Transmission Neutral

Switch (Some transmissions require high range in Neutral)

Hood SwitchUnder-hood AlarmStart RelayOverlay RelayVSS EnabledOptional Sleeper Thermostat

25ST0072-2 Rev. 04/4/00 132

Optimized Idle Shutdown Sequence

Park Brake set with hood closed and transmission in Neutral supplies ground to the Park Brake input and the Overlay Relay. Idle Timer starts and the Overlay Relay closes supplying power to the Start Relay.

Optimized Idle is activated by turning on the Cruise Enable Switch which supplies ground on the Cruise Enable input.

Optimized Idle Light flashes until the engine shuts down then remains on.

25ST0072-2 Rev. 04/4/00 133

Optimized Idle Shutdown Sequence

With Battery Voltage above 12.2V, Oil Temp between 15ºC/60ºF and 40ºC/104F, and Sleeper Temp within limits, the Idle Timer shuts the engine down.

Vehicle Power Down Relay opens powering down the vehicle Ignition Circuit.

With Ignition key on, the ECM is still awake and it continuously monitors Battery Voltage, Oil Temperature and Sleeper Temperature.

25ST0072-2 Rev. 04/4/00 134

Optimized Idle Start Sequence • With the hood closed, Transmission in Neutral, Park Brake set, and the Optimized Idle dash light ON,the ECM supplies ground on PWM #2, wire 909 which activates the under-hood alarm. • ECM then supplies ground on PWM #3, wire 910

which closes the Start Relay. • After the engine starts, the ECM supplies ground to the Vehicle Power Down relay which closes to

supply Ignition power to the vehicle

25ST0072-2 Rev. 04/4/00 137




EEPROMEEPROM

+-Battery

Engine Brake

StopEngine

CheckEngine

Cruise ControlVehicle Speed LimitingVehicle Speed Sensor

Oil / Fuel Pressure



Pressure Governor

Coolant Level

Timing Reference

Synch Reference

Fan Controls

VSG Control

PWM Ports


Progressive Shift

DiagnosticRequest

Stop EngineOverride

ISD / VehiclePower Down


CommunicationDDR Interface/ DDDL/ Reprogramming

Optimized IdleEUIEUI

Oil level/Fuel RestrictionCrankcase Pressure

Digital Inputs

25ST0072-2 Rev. 04/4/00 140

Digital Input Functions

• External switch requests function from the ECM• 31 options to choose from• 12 pins available on the 30 pin vehicle harness

connector for input functions • Functions are assignable to any of these pins

through the use of a “Reprogramming Station”

25ST0072-2 Rev. 04/4/00 141

DIGITAL INPUTS

Battery

_+

#953

Cruise Enable

Fan Override

#150

No Function

No FunctionNo Function

ECMECM

EEPROMEEPROM

25ST0072-2 Rev. 04/4/00 142

Digital Inputs

• Air Compressor Controls– Air Compressor Load Switch

• Cruise Control (Uses Up to Five Inputs)– Cruise Enable– Clutch Released– Service Brake Released– Set/Coast On (Decrease)– Resume/Acceleration On

(Increase)• Engine Brake

– Engine Brake Disable– Engine Brake Low– Engine Brake Medium

• Engine Protection– Auxiliary Input Protection #1– Auxiliary Input Protection #2– Diagnostic Request Switch– SEO/Diagnostic Request

Switch• Engine Ratings

– Limiting Torque Curve– Rating Switch #1– Rating Switch #2

• Fan Control– Transmission Retarder Status

(Release 2.00 or Later only)– Air Conditioner Status– Fan Control Override

25ST0072-2 Rev. 04/4/00 143

Digital Inputs (Cont’d)

• Throttle Control– Alternate Minimum VSG/Fast

Idle (Release 2.00 or Later Only)

– Dual Throttle (LSG)– Idle Validation Switch– Throttle Inhibit– VSG Station Change– VSG Station Complement

• Pressure Governor System (PGS) (Uses Five Inputs)– Pressure Governor System

Enable– Pressure/RPM Mode Switch– Set/Coast On (Decrease)– Resume/Acceleration On

(Increase)

• Additional Functions– Auxiliary Coolant Level

Sensor– Parking Brake Interlock

Digital Outputs

25ST0072-2 Rev. 04/4/00 145

Digital Output Functions

• ECM commands (internal switches/grounds) action of some external device- fan control

• 22 output options• 6 pins available, 3 on the 30 pin vehicle connector, 3

on the 30 pin engine harness connector (auxiliary outputs)

• Configurable with the distributor or dealer reprogramming station

25ST0072-2 Rev. 04/4/00 146

OUTPUTS

ECM

SEL

To Jake brake

Ignition#439

25ST0072-2 Rev. 04/4/00 147

Digital Outputs

• Coolant Level Low Light• Cruise Control Active Light (PGS

Active Light)• Deceleration Light• Engine Brake Active• Fan Control #1• Fan Control #2• Low DDEC Voltage• Pressure Governor System

Pressure Mode Light• Starter Lockout• Transmission Retarder• Vehicle Power Shutdown

• VSG Active Indication• (Release 2.00 or Later only)

– Low Oil Pressure Light

– High Oil Temperature Light

– High Coolant Temp. Light

• (Release 3.00 or Later Only)– Ether Injection

– Low Coolant Pressure Light

– High Crankcase Pressure Light

• (Release 4.00 or Later Only)– Optimized Idle Active light

• Gas Solenoid Shutdown• Air Compressor Load Switch

25ST0072-2 Rev. 04/4/00 148

• Encourages better driving habits by rewarding good fuel economy with extra road speed

• If driver exceeds the target fuel economy extra road speed will automatically be added to his maximum vehicle speed

Fuel Economy Incentive

25ST0072-2 Rev. 04/4/00 149

Fuel Economy Incentive

Parameter Range ExampleMin MPG 5-10 mpg 7.0Max MPH 0-10 mph 4Scaler MPH/MPG 0.1-20 mph/mpg 10.0Calc Type Filtered/Trip Trip

If Scaler is set at:20.0 = 1 extra mph for every .05 mpg above target mpg 10.0 = 1 extra mph for every .1 mpg above target mpg 5.0 = 1 extra mph for every .2 mpg above target mpg 2.0 = 1 extra mph for every .5 mpg above target mpg 1.0 = 1 extra mph for every 1.0 mpg above target mpg

If Calc Type is set at:Filtered - Calculates using Total Engine DataTrip - Calculates using Trip Data

25ST0072-2 Rev. 04/4/00 150

PasSmart

• Electronically Controlled Increased Passing Speed– PasSmart is an electronic feature that enables a fleet

manager to enable a second Vehicle Speed Limit (VSL) to assist drivers during passing.

– This second Vehicle Speed Limit (VSL) is programmed for a limited duration during a given period This feature is available with DDEC IV Software version R28.00.

– As and example: If the fleet policy is 65 Miles Per Hour (MPH) the fleet manager can increase the Vehicle Speed Limit (VSL) an additional 5-20 MPH for 1- 255 minutes per day.

Maintenance Alert System

25ST0072-2 Rev. 04/4/00 152

Maintenance Alert Sensors System

• Designed to Provide Preventative Maintenance Information to Mechanics and Operators

• Reduces Unexpected Downtime

• Optimizes Normal Routine Service

• Used on Highway Trucks only at this time

25ST0072-2 Rev. 04/4/00 153


• Overview– Based on Inputs from Customers, the Maintenance Alert

System Provides Preventative Maintenance Information to Mechanics and Drivers to Reduce Unexpected Downtime and to Assist Normal Routine Service Scheduling

• Features– Uses DDEC IV ECM– New DDEC Software Processes Information– Incorporates Four New Sensors (Both On and Off Engine)– Optional Remote Mounted Monitor Display Unit Available

25ST0072-2 Rev. 04/4/00 154


Oil Level Sensor Air Filter Restriction Sensor 2nd Coolant Level Sensor

Fuel Restriction Sensor Monitor Display Unit

25ST0072-2 Rev. 04/4/00 155

DDC Installed Components

• Includes Two Maintenance Alert System Sensors

– Oil Level Sensor (Requires Front Sump Non-metal Oil Pan) Will not work on Rear Sump Applications

– Fuel Restriction Sensor

25ST0072-2 Rev. 04/4/00 156


• Oil Level Sensor– Mounts in Front Sump Non-

metal Oil Pan– Utilizes Optical Technology to

"See" Oil Level– Engine Must Be Off (Zero

RPM ) for "X" Minutes (Based on Oil Temp.) to Drain Oil Back to the Pan

– Switches at Four Quart Low Level

25ST0072-2 Rev. 04/4/00 157


• Fuel Restriction Sensor– Measures Fuel System

Restriction at Fuel Pump Inlet– Sensor Measures Actual Inlet

Restriction

25ST0072-2 Rev. 04/4/00 158

Optional OEM Installed Components

• OEMs Install These Components if Ordered by Customer (Any Combination but Must Include On Engine Components)

– 2nd Coolant Level Sensor – Air Filter Restriction Sensor – Monitor Display Unit

25ST0072-2 Rev. 04/4/00 159

OEM Installed Components• 2nd Coolant Level Sensor (CLS)

– Separate Sensor from Current Primary CLS

– Mounted in Coolant Surge Tank Above Primary CLS

– Requires Interface Module– OEM Impact

» Order Engine Mounted Sensors» Purchase CLS Sensor and Module

from PDC» Mount Sensor in Surge Tank» Mount Interface Module» Provide Wiring Between the

Sensor/Module/Engine Harness» Use VEPS( Vehicle Engine Program

Station) to "Turn On” OEM Only

25ST0072-2 Rev. 04/4/00 160

OEM Installed Components

• Air Filter Restriction Sensor– Electronic Version of the

Mechanical Filter Minder®– Switch Points at 15 and 20

Inches of Water– OEM Impact

» Order Engine Mounted Sensors» Purchase Sensor from

Engineered Products or PDC» Install into Turbo Inlet Tube» Provide Wiring from Sensor to

Engine Harness Pigtail» Use VEPS to "Turn On"

25ST0072-2 Rev. 04/4/00 161

OEM Installed Components

• Monitor Display Unit– 2 Buttons and 8 LEDs (Green, Red, &

Yellow)– Mounted in Cab– Reads Engine J1587 Data Link for

Information– Can Access Maintenance Information

with Ignition On or Up to 2 Hours After Ignition Off

– Stores Status after 2 Hours for Later Display

– OEM Impact» Order Engine Mounted Sensors» Purchase Display from PDC» Design and Install Display Bracket» Provide Wiring to Display

25ST0072-2 Rev. 04/4/00 162

Service Tools

• Diagnostic Data Reader-(DDR) (Version 24.0 and higher• Detroit Diesel Diagnostic Link (DDDL) - Version 3.0

and higher

– Sensor Alerts Due to Failed Sensors– Quick Access Screen to Show Maintenance Alert System

Alerts» Clear Maintenance Alert System (MAS) Filter Alerts

– Maintenance Alert System sensors added to Data List– Warning Light Option Programming

25ST0072-2 Rev. 04/4/00 163

Summary

Engine

Vehicle

• Monitors and Displays Service Requirements– Oil Level– Fuel System Restriction – Air Filter Restriction– 2nd Coolant Level– Monitor Display Unit - in Cab– DDR and DDDL

• Engine Only or Engine and Any Vehicle Sensors• Oil Level Requires Front Sump Plastic Plan• Display is Optional

Construction & Industrial

25ST0072-2 Rev. 04/4/00 165

Construction & Industrial

• Electronic Display Module (EDM) • Auxiliary Interface Module (AIM)• Air Comp Controls• Fuel Pressure Sensor (Low HP)• Nylon Vs. Plastic Harness• Multiple ECM• Optimized Idle• Switch Power• J1939

Wire Crimping Exercise

25ST0072-2 Rev. 04/4/00 167

Wire Crimping Tools

25ST0072-2 Rev. 04/4/00 168

Wire Crimping Tools

25ST0072-2 Rev. 04/4/00 169

Wire Crimping Tools

25ST0072-2 Rev. 04/4/00 170

Wire Crimping Tools

25ST0072-2 Rev. 04/4/00 171

Wire Crimping

Wire Splicing

25ST0072-2 Rev. 04/4/00 173

Wire Splicing Tools

Series 71 & 92 SRS / TRS Adjustment

25ST0072-2 Rev. 04/4/00 175

Series 71/92 SRS/TRS Adjustment

Basic Electricity -Wire Harness Exercise

25ST0072-2 Rev. 04/4/00 200

Sensor Operations

Operates on 5 Volts for All D.C. Sensors

.25 4.75

NormalOperating

Range

Low Voltage

0 5

High Voltage

25ST0072-2 Rev. 04/4/00 201

Sensor Wiring

• Common Return Circuit. #452

• Thermistor

• Piezoresistive Pressure sensor

• Voltage is Proportional to Pressure

25ST0072-2 Rev. 04/4/00 202

2-wire Sensors

5V Supply

Signal

Return

ECM Sensor

Open = HI VOLTAGE

Short = LO VOLTAGE

25ST0072-2 Rev. 04/4/00 203

3-wire Sensors

ECM Sensor5V Supply

Signal

Return

Open Supply = LOW VOLTAGEOpen Signal = LOW VOLTAGEOpen Return = HI VOLTAGESupply short to Signal = HI VOLTAGESupply short to Return = LOW VOLTAGESignal short to Return = LOW VOLTAGE

25ST0072-2 Rev. 04/4/00 204

Electrical System

452

Definitions• Open Circuit

– An “open” describes a complete break in the path of current at some point in the circuit. The result of an “open” is that one or more loads in the circuit do not work.

Open

High voltage code

120

25ST0072-2 Rev. 04/4/00 205

Electrical System

452432416

Cavity ACavity BCavity C

Definitions• Open Circuit

– An “open” describes a complete break in the path of current at some point in the circuit. The result of an “open” is that one or more loads in the circuit do not work.

Open

Low voltage code

25ST0072-2 Rev. 04/4/00 206

Electrical System

432416


Definitions• Short Circuit

– A “short” occurs when a load in the circuit is accidentally bypassed. Electricity will always take the path of least resistance. The result of a “short” is that higher current flows, causing excessive heat or action from a device protecting the circuit (blown fuse or activated circuit breaker).

Short High Voltage Code

452

25ST0072-2 Rev. 04/4/00 207

Electrical System

452432416


Definitions• Grounded Circuit

– A “ground” is similar to a “short” because current accidentally bypasses a load in the circuit. The difference is that the bypass connects directly to the negative terminal of the power source by way of the chassis ground path.

GroundLow Voltage Code

Troubleshooting Tools

25ST0072-2 Rev. 04/4/00 209


Volt-Ohm Meter

To properly probe terminals use Kentmoore jumper wire kit number J39197. Within this kit the proper leads are provided.

The use of the lead ends of the volt ohm meter to probe the terminal ends will damage the DDEC connectors and will cause intermittent codes.

25ST0072-2 Rev. 04/4/00 210


Sensor TesterJ37164-A

Breakout Box (30 Pin)J35634

DDEC III/IV InterfaceJ41005

25ST0072-2 Rev. 04/4/00 211


• NEW DDEC Engine Protection Test Kit Number 23526923

Purpose: To Reduce Diagnostic Troubleshooting time

KIT INCLUDES

1. Coolant Level Low Simulator P/N 23524785

2. High Oil/Coolant Temperature P/N 23524787

3. Low Oil Pressure Simulator P/N 23524786

ddec master 2000 current4-6

Documents