designed to protect your cisco® network wireless...
TRANSCRIPT
Designed to Protect
Your Cisco® Network
Investment
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
SecureConvenient
Aesthetic
Physical security
Ideal mounting orientation
Simplify moves, adds, and changes
See our full line at oberonwireless.com
Mount and Secure Your Cisco® Wireless Access Points
Whether you require ceiling enclosures, wall enclosures, wall brackets, plenum-rated enclosures, or NEMA enclosures, Oberon has the right product for you.
Oberon is the only Registered Partner manufacturer of wireless access point enclosures in the Cisco Developer Network (CDB) Program. This means that Cisco engineering has tested the Oberon product for compatibility with Cisco’s wireless access points. Please visit the Oberon CDN page for more information.
Secure Networking Equipment in the Space Where It Is Needed
Mount switches and other equipment in the office ceiling or on the wall. Oberon is Bringing Bandwidth Closer to the UserTM!
Wireless AP and Telecom Enclosures
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Suspended Ceiling Access Point Mount
BIM, CAD, and CSI Specifications
Model 1068-00
Oberon’s Model 1068-00 universal wireless access point ceiling mount is designed to provide a secure,
convenient, and aesthetic mounting solution for most vendors wireless access points. This aesthetic, white
powder coated steel 2’ x 2’ ceiling tile-like mount locks the access point in place with a patent pending locking
mechanism. The access point is attached to a vendor model specific mounting plate, and the plate is locked in
place into the ceiling tile. Access point moves, adds, and changes can be performed without removing the
mount from the ceiling. No ceiling tile cuts are required for installation.
Model 1068-00 shown without Wireless Access Point and with Cisco 3500
Specifications:
• Locking ceiling mount designed for secure, aesthetic, low profile mounting of most vendor’s wireless
access points
• Interchangeable mounting plates permit migration or upgrades to different vendor’s wireless solutions
• UL Listed and designed to meet NEC paragraphs 300-22 and 300-23 for plenum installations
• OSHPD approved OPA # 1638
• Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
• Patent pending locking mechanism, keyed alike, secures access point into the ceiling mount
• Size: 2’ x 2’ x 2” deep. Fits into standard (U.S.) suspended ceiling systems.
• Weight: 10.5 lbs (not including access point)
• Mount must be supported by the building structure independent of the suspended ceiling, per NEC
paragraph 300.11.
• Contact your Oberon representative for the vendor specific mounting plate required. Mounting plates
are available for leading wireless access points. Plates sold separately.
Model 1068-00 Includes:
• (1) cable egress fire block kit (¾” Trade size conduit connector and fire block foam insert)
• (4) Hanger wires
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Suspended Ceiling Access Point Mount
BIM, CAD, and CSI Specifications
Model 1064-00
The Model 1064-00 wireless access point ceiling mount is designed to provide a secure, convenient, and
aesthetic mounting solution for the Cisco 1040/1140/1260/3500/3600 series 802.11n access points. This
aesthetic, white powder coated steel 2’ x 2’ ceiling tile-like mount locks the access point in place with a patent
pending locking mechanism. Access point moves, adds, and changes can be performed without removing the
mount from the ceiling. No ceiling tile cuts are required for installation. The Model 1064-T features a 3/8’’
bevel in the flange around the perimeter, to match “tegular” ceiling tiles commonly used in new construction
and renovations.
Model 1064-00 shown with Cisco 1140 series AP (not included)
Specifications:
• Economical ceiling mount designed specifically for aesthetic, secure mounting of the Cisco
1040/1140/1260/3500/3600 series access points
• Use Cisco AIR-AP-BRACKET-1 for 3600 series and AIR-AP-BRACKET-2 for 3500 series
• UL listed and designed to meet NEC300-22 and 300-23 for plenum installations
• OSHPD approved OPA # 1638
• Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
• Patent pending locking mechanism, keyed alike, secures Cisco AP into the ceiling mount
• Size: 2’ x 2’ x 2” deep
• Weight: 9.5 lbs (not including access point)
• Mount must be supported by the building structure independent of the suspended ceiling
Model 1064-00 Includes:
• (1) ¾” Trade size conduit connector for data cable
• (1) Fire block foam insert for conduit connector
• (4) Hanger wires
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Suspended Ceiling Access Point Mount
BIM, CAD, and CSI Specifications
Model 1064-T
The Model 1064-T wireless access point ceiling mount is designed to provide a secure, convenient, and
aesthetic mounting solution for the Cisco 1040/1140/1260/3500/3600 series 802.11n access point. This
aesthetic, white powder coated steel 2’ x 2’ ceiling tile-like mount locks the access point in place with a patent
pending locking mechanism. Access point moves, adds, and changes can be performed without removing the
mount from the ceiling. No ceiling tile cuts are required for installation. The Model 1064-T features a 3/8’’
bevel in the flange around the perimeter, to match “tegular” ceiling tiles commonly used in new construction
and renovations.
Model 1064-T shown with Cisco 1140 series AP (not included), notice the “tegular” flange perimeter
Specifications:
• Economical ceiling mount designed specifically for aesthetic, secure mounting of the Cisco
1040/1140/1260/3500/3600 series access point
• Use Cisco AIR-AP-BRACKET-1 for 3600 series and AIR-AP-BRACKET-2 for 3500 series
• UL Listed and designed to meet NEC300-22 and 300-23 for plenum installations
• OSHPD approved OPA # 1638
• Construction: 18 ga. textured white powder-coated steel flange, 16 ga. aluminum backbox
• Patent pending locking mechanism, keyed alike, secures AP into the ceiling mount
• Size: 2’ x 2’ x 2” deep
• Weight: 10 lbs (not including access point)
• Mount must be supported by the building structure independent of the suspended ceiling
Model 1064-T Includes:
• (1) ¾” Trade size conduit connector for data cable
• (1) Fire block foam insert for conduit connector
• (4) Hanger wires
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Suspended Ceiling Enclosure
BIM, CAD, and CSI Specifications
Model 1030-FLANGE
Oberon’s Model 1030-00 “hard lid” or wall mount enclosure provides a secure, aesthetic, convenient
mounting solution for wireless access points from most vendors. The enclosure has a low profile impact
resistant ABS dome so that wireless access points with integrated or non-detachable antennas can be secured
in otherwise unsecured spaces. The product is UL Listed and designed to satisfy National Electric Code (NEC)
paragraphs 300-22 and 300-23 for installation in the air handling space. Locks are “keyed-alike” to simplify
moves, adds, and changes. An optional suspended ceiling flange kit, 1030-FLANGE, permits the Model 1030-00
to be mounted in a standard 2’ x 2’ suspended ceiling system.
Oberon Model 1030-FLANGE kit shown with Model 1030-00 and Cisco 1142 wireless access point (not included)
Specifications:
• Wireless access point enclosure designed to be surface mounted on “hard-lid” ceilings or walls.
• Designed to accommodate wireless access points from most vendors with integrated or non-
detachable antennas
• UL listed and designed to meet NEC300-22 and 300-23 for air handling space installations
• OSHPD approved (OPA # 1638)
• Construction: 16 gauge, powder coated steel back box, fully hinged locking door with UL 94-5VA ABS
plastic
• Dome is impact resistant and transparent to wireless signals
• Knockouts for ¾” trade conduit connectors and snap-in keystone jacks and connectors
• Opening in back box for wall jacks
• Size: Flange is 22" x 24", Enclosure is 17" x 17" x 3 ½" (total depth), the dome is 12” x 12” x 2”
• Weight: 17.5 lbs (not including access point)
• Suspended ceiling flange kit (part number 1030-FLANGE) is optional
• If enclosure is in flange it must be supported by the building ceiling structural system, not tile gridwork.
Model 1030-FLANGE & 1030-00 Includes:
• (1) Universal access point mounting plate
• (1) ½” Trade size conduit connector
• (2) Keys for lock
• (4) # 6-32 x 3/16 Screws
• (4) # 8-32 x 3/16 Screws
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
“Hard-Lid” Ceiling or Wall Mount Enclosures
BIM, CAD, and CSI Specifications
Model 1030-00
Oberon’s Model 1030-00 “hard lid” or wall mount enclosure provides a secure, aesthetic, convenient
mounting solution for wireless access points from most vendors. The enclosure has a low profile impact
resistant ABS dome so that wireless access points with integrated or non-detachable antennas can be secured
in otherwise unsecured spaces. The product is UL listed and designed to satisfy National Electric Code (NEC)
paragraphs 300-22 and 300-23 for installation in the air handling space. Locks are “keyed-alike” to simplify
moves, adds, and changes. An optional suspended ceiling flange kit, 1030-FLANGE, permits the Model 1030-00
to be mounted in a standard 2’ x 2’ suspended ceiling system.
Oberon Model 1030-00 wireless LAN access point enclosure shown with Cisco 1142 access point (not included)
Specifications:
• Wireless access point enclosure designed to be surface mounted on “hard-lid” ceilings or walls.
• Designed to accommodate wireless access points from most vendors with integrated or non-
detachable antennas
• UL listed and designed to meet NEC300-22 and 300-23 for air handling space installations
• OSHPD approved (OPA # 1638)
• Construction: 16 gauge, powder coated steel back box, fully hinged locking door with UL 94-5VA ABS
plastic
• Dome is impact resistant and transparent to wireless signals
• Knockouts for ¾” trade conduit connectors and snap-in keystone jacks and connectors
• Opening in back box for wall jacks
• Size: 17" x 17" x 3 ½" (total depth), the dome is 12” x 12” x 2”
• Weight: 13 lbs (not including access point)
• Suspended ceiling flange kit (part number 1030-FLANGE) is optional
• If enclosure is in flange it must be supported by the building ceiling structural system, not tile gridwork.
Model 1030-00 Includes:
• (1) Universal access point mounting plate
• (1) ½” Trade size conduit connector
• (2) Keys for lock
• (4) # 6-32 x 3/16 Screws
• (4) # 8-32 x 3/16 Screws
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Suspended Ceiling Enclosure
BIM, CAD, and CSI Specifications
Model 1052-CCOAP
Oberon’s Model 1052-CCOAPwireless LAN access point enclosure is a locking, 2’ x 2’ ceiling tile enclosure
designed specifically to conveniently mount and secure the Cisco 1040/1140/1260/3500/3600 series access
points. The enclosure is based on Oberon’s popular 1052-00 universal wireless access point enclosure, with a
door designed specifically for Cisco’s newest access points. No ceiling tile cuts are required for installation. Just
mount the access point into the door, place the ceiling tile enclosure in the ceiling, secure the enclosure to the
ceiling support structure, and the access point is conveniently and aesthetically secured in the ceiling.
Upgrades to different styles of access points are achieved by simply unlocking and replacing the door.
1) Model 1052-CCOAPand Cisco 1142 AP (not included) 2) Exploded view of the door, access point, access point mounting bracket,
and assembly mount bracket
Specifications:
• Ceiling tile enclosure specifically designed for Cisco 1140/1260/3500/3600 series wireless access points
• Use Cisco AIR-AP-BRACKET-1 for 3600 series and AIR-AP-BRACKET-2 for 3500 series
• UL listed and designed to meet NEC300-22 and 300-23 for installations in air handling spaces
• OSHPD approved OPA # 1638
• Construction: Textured white powder-coated steel, 16 ga. backbox, 14 ga. door
• Fully hinged locking door, keyed alike. Door can be replaced to migrate to new access points.
• Size: Flange is 2’ x 2’, AP Enclosure is 12.5" x 12.5 " x 4.5" deep
• Weight: 13lbs (not including access point or antenna)
• Enclosure must be supported by the building structural system, not the tile gridwork.
Model 1052-CCOAPIncludes:
• Access point mounting screws
• (4) Suspension wires
• (1) fire block kit (¾” trade conduit connector and fire block foam)
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Adaptor Doors
BIM, CAD, and CSI Specifications
Model 38-52-CCOAP
Oberon’s Model 1052-00 wireless LAN access point enclosure is a locking 2’ x 2’ ceiling tile enclosure originally
designed for the Cisco 1242, Cisco 1232, and Aruba Networks AP-70 access points. With many Cisco customers
making the migration from the Cisco 1242 to the Cisco 1040/1140/1260/3500/3600 series 802.11n wireless
access point, Oberon has designed the 38-52-CCOAP adaptor door so that customers may install the new
access point in the existing enclosure, without removing the enclosure from the ceiling. The upgrade simply
requires that the existing 1052-00 door is removed (three interior nuts), the new access point is attached to
the adaptor door, and the adaptor door is attached to the enclosure. The upgrade maintains the enclosure’s
UL 50 design criteria, and provides the same level of physical security as previously provided. Upgrades are
performed without accessing the air handling space above the ceiling.
1) Model 1052-00 shown with 38-52-CCOAP and Cisco 1142 AP (not included) 2) Exploded view of the door, access point, access
point mounting bracket, and assembly mount bracket
Specifications:
• Adaptor door designed to mount the Cisco 1040/1140/1260/3500/3600 series 802.11n wireless access
point into existing Oberon Model 1052-00 ceiling tile enclosures
• Use Cisco AIR-AP-BRACKET-1 for 3600 series and AIR-AP-BRACKET-2 for 3500 series
• With adaptor door properly installed, the assembly is UL listed and designed to meet NEC300-22 and
300-23 for plenum installations
• Construction: Textured white powder-coated steel, 14 ga. door
• Fully hinged locking door, keyed alike.
• Adaptor door is attached to enclosure with (3) nuts
Model 38-52-CCOAP Includes:
• Adaptor door
• Assembly mount bracket and nuts
• Installation instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867‐2312 ● Fax (814) 867‐2314 ● www.oberonwireless.com
Suspended Ceiling Enclosure
BIM, CAD, and CSI Specifications
Model 1059‐00
The Model 1059‐00 wireless LAN access point enclosure is a locking, 2’ x 2’ ceiling tile enclosure designed to accommodate access points with non‐detachable antennas from most manufacturers. This aesthetic, white powder coated steel enclosure has an impact resistant, RF transparent door, which protrudes only 4" below the ceiling plane. No ceiling tile cuts are required for installation.
Model 1059‐00 shown with Cisco 1242 AP and standard dipole antennas (not included)
Specifications:
Ceiling tile enclosure designed for access points from most manufacturers RF transparent cover allows use of access point with non‐detachable or integrated antennas UL50 Listed and designed to meet NEC300‐22 and 300‐23 for plenum installations Dome is UL 94‐5VA Classified ABS Plastic OSHPD approved OPA # 1638 Enclosure is deep enough for any access point with an overall height of less than 5¾" Construction: Textured white powder‐coated steel, 16 ga. backbox, UL‐94V5A impact resistant
textured white ABS door Fully hinged locking door, keyed alike Size: Flange is 2’ x 2’, AP Enclosure is 18" x 18" x 2.6" deep, ABS dome is 14" Sq. x 4" deep Weight: 17.5lbs (not including access point) Ceiling mounts must be supported by the building structure independent of the suspended ceiling
Model 1059‐00 Includes:
Universal mounting plate, mounting screws and hardware (4) Suspension wires (2) ¾” Trade size conduit connectors for power/data cable openings in the back‐box Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Wall Mount Enclosures
BIM, CAD, and CSI Specifications
Model 1029-00
Many wireless access point manufacturers recommend that the access point be mounted in a “horizontal”
orientation to achieve best wireless coverage. Horizontal mounting may be difficult in hard lid and other
environments where the access point is mounted on the wall. Oberon’s Model 1029-00 wireless LAN access
point wall mount bracket is designed to mount and secure access points from most manufacturers in areas
were wall mounting is required. This aesthetic, white powder coated steel mounting bracket is ideal for
mounting the access point in the preferred “horizontal” orientation. Conduit, raceways, and cable can be
securely terminated inside the enclosure to provide for a clean appearance. The access point can be locked in
place using the manufacturer’s bracket lock feature.
1) Model 1029-00 shown with Cisco 1040 access point (not included) 2) 1029-00 with cover off & wall plate (not included)
Specifications:
• Designed for mounting on indoor walls, where secure horizontal mounting is required
• Designed for Cisco 1040/1140/1260/3500/3600 series
• Knockouts on two sides and top for 1/2” trade size conduit clamps
• 2 part Construction: textured white powder coated 18 gauge steel right angle bracket and cover
• Size: 9" x 6" wide x 5” tall
• Weight: 3.5 lbs with out equipment
Model 1029-00 Includes:
• (4) #8 screws
• (4) #6 screws
• (4) screws for the cover
• Mounting Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
“Hard-Lid” Ceiling or Wall Mount Enclosures for WAPs
BIM, CAD, and CSI Specifications
Model 1032-00
Oberon’s Model 1032-00 “hard lid” or wall mount enclosure provides a secure, aesthetic, convenient
mounting solution for wireless access points from many vendors. This economical enclosure has a low profile
impact resistant ABS dome so that wireless access points with integrated or non-detachable antennas can be
secured in otherwise “unsecured” spaces. The product is designed to provide an unobtrusive mounting
solution. Locks are keyed-alike to simplify moves, adds, and changes.
Specifications:
• Wireless access point enclosure designed to be surface mounted on “hard-lid” ceilings or walls.
• Economical solution for securing wireless access points with integrated or non-detachable antennas,
from most vendors
• Construction: 16 gauge powder coated steel back box, UL 94-5VA ABS plastic cover
• Fully hinged locking cover is impact resistant and transparent to wireless signals
• Knockouts for ¾” trade conduit connectors, and snap-in keystone jacks and connectors
• Opening in back box for wall jack
• Size: 11" x 11" x 4.4" (total depth)
• Weight: 4.5 lbs (not including access point)
Model 1032-00 Includes:
• (1) Universal access point mounting plate
• (2) Keys for lock
• Mounting Instructions
• (4) # 6-32 x 3/16 Screws
• (4) # 8-32 x 3/16 Screw
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
“Hard-Lid” Ceiling or Wall Mount Enclosures
BIM, CAD, and CSI Specifications
Model 1032-C
Oberon’s Model 1032-C “hard lid” or wall mount enclosure provides a secure, aesthetic, convenient mounting
solution for wireless access points from many vendors. This economical enclosure has an impact resistant,
clear, lockable polycarbonate cover so that wireless access points with integrated or non-detachable antennas
can be secured in otherwise unsecured spaces. The product is designed to provide an unobtrusive mounting
solution. Locks are keyed-alike to simplify moves, adds, and changes.
Model 1032-C shown with Cisco 3500i AP (not included).
Specifications:
• Wireless access point enclosure designed to be surface mounted on “hard-lid” ceilings or walls.
• Economical solution for securing wireless access points with integrated or non-detachable antennas,
from most vendors
• Construction: 16 gauge powder coated steel back box, UL 94-V2 polycarbonate cover
• Fully hinged locking cover is impact resistant and transparent to wireless signals
• Knockouts for ¾” trade conduit connectors, and snap-in keystone jacks and connectors
• Opening in back box for wall jack
• Size: 11" x 11" x 4.4" (total depth)
• Weight: 4.5 lbs (not including access point)
Model 1032-C Includes:
• (1) Universal access point mounting plate
• (2) Keys for lock
• Mounting Instructions
• (4) # 6-32 x 3/16 Screws
• (4) # 8-32 x 3/16 Screw
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867‐2312 ● Fax (814) 867‐2314 ● www.oberonwireless.com
PAGE 29
Ceiling Mounted Telecommunications Enclosures
BIM, CAD, and CSI Specifications
Model 1070
Oberon’s Model 1070 ceiling mounted telecommunications enclosure is a secure, convenient, and aesthetic telecommunications enclosure for rack mountable Ethernet switches, patch panels, wireless controllers and other networking and A/V components. The 1070 has mounting brackets for up to 2 standard (1U) rack mountable components, and back‐box openings to mount a patch panel and CCH fiber optic adaptor panel. The enclosure has a highly perforated door to allow airflow, for fan‐less operation. The 1070 is ideal for structured cabling and Fiber–to‐the‐Enclosure (FTTE) deployments. The enclosure can be used to shorten home‐runs to improve data rate and network capacity.
Model 1070‐WH Model 1107‐BL
Model 1070 Telecommunications Enclosure shown with 48‐port Ethernet Switch and Patch Panel (not included)
Specifications:
Telecommunications Enclosure (TE) designed for suspended ceiling environments
Designed to accommodate up to 2 standard (1U) rack mountable components
Includes back‐box openings for standard (1U) rack mountable patch panel and a CCH fiber optic adaptor panel (not included)
UL Listed and is designed to satisfy National Electric Code (NEC) paragraphs 300‐22 and 300‐23 for installation in the air handling space
Designed to fit into 2’ x 2’ ceiling tile grid‐work, accommodates networking equipment up to 2U deep and 14” in length
Construction: Black powder coated aluminum
Highly perforated door permits air‐flow without a fan. De‐rate networking equipment by 13º F (This is comparable to the temperature rise in an open rack).
Weight: 7 lbs (not including networking equipment)
Enclosure must be supported by the building ceiling structural system, not tile gridwork.
Model 1070 Includes:
(1) AC Junction box, receptacle, cover and screws
(1) ½” Trade size conduit connector
Grounding lug
(4) Rack mounting screws
Installation instructions
Available in Black (1070‐BL) and White (1070‐WH)
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Ceiling Mounted Workspace Telecommunications Enclosures
Model 1072-00
The Model 1072-00 is a locking 2’ x 2’ ceiling tile telecommunications enclosure designed for ac powered in-
building wireless and wireless LAN components, including Wi-Fi access points, DAS remote access units,
smaller access switches, fiber optic adaptor panels and rack mounted patch panels. The enclosure includes a
universal mounting plate for access points and brackets for rack mountable networking components. This
aesthetic, white powder coated aluminum enclosure has openings in the door for up to eleven antennas,
including larger multi-carrier cellular antennas. No ceiling tile cuts are required for installation.
Model 1072-00 shown with (6) optional Oberon 34-ZDUAL Antennas and Oberon 34-MULTI-CARRIER cellular antenna (optional)
Specifications:
• 2’ x 2’ Ceiling tile telecommunications enclosure (TE) designed for multiple networking components
• Accommodates most manufacturers’ wireless LAN access points with Oberon universal mounting plate
P/N 38-1052-MNT-KIT (1 included).
• Adjustable 19” rack mounting brackets for 2U deep equipment, opening in back box for 19” patch
panel and openings in sidewalls for CCH style fiber optic adapter panel
• Designed to meet NEC300-22 and 300-23 for air handling space installations (all metal construction)
• OSHPD approved OPA # 1638 (up to 25lbs total weight)
• Openings in door for up to eleven external 802.11 Wi-Fi or cellular/PCS multi-carrier antennas
• Construction: 16 ga. back-box, 14 ga. door textured, white, powder coated aluminum
• Fully hinged locking door, keyed alike
• Size: Fits in standard 2’ x 2’ ceiling grid, back box is 22.5" x 22.5 " x 4.5" deep
• Weight: 15.5lbs (not including internal equipment)
• Enclosure must be supported by the building ceiling structural system, not the tile gridwork.
Model 1072-00 Includes:
• (1) universal mounting plate and hardware, (1) pair of rack mount brackets
• (4) Suspension wires, mounting instructions
• (2) ¾” Trade size conduit connectors for power/data cable openings in the back-box
• UL Listed Junction box, receptacle, and cover plate for ac power
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Cabinets for Organizing Wireless Network Components
Model 1082-00
Oberon’s Model 1082-00 is a wall mounted home/office cabinet for organizing your networking components.
The 1082-00 provides a convenient way to interconnect and stow your broadband modem, wireless router,
small network switch, power strip, network storage, and other components. This 22” x 22” cabinet has a steel
back box with adjustable shelves for components and wire tie- downs to manage the data and power wiring.
The cabinet has a locking, impact resistant ABS door which is virtually transparent to wireless signals. The
cabinet mounts on the wall in minutes, and aesthetically secures all of your networking components. The
cabinet’s low 4” profile allows the cabinet to be mounted just about anywhere in your home or office.
Oberon Model 1082-00 shown with switch, patch panel, wireless router, and DSL modem (not included)
Specifications:
• Wall mounted network components cabinet ideal for wireless routers, broadband modems, small
switches, power strips, network storage and other components from most manufacturers
• Openings in the back box permit the cabinet to be mounted directly over the broadband connector or
network wall plate. Surface mounts to the wall in minutes
• The cabinet back-box has mounting features for 3 adjustable shelves, or (optional) 19” rack mounting
brackets for up to 2U deep equipment
• Openings in the top and bottom for cable raceway or conduit entry
• Construction: 16 ga. Textured white powder coated steel back box
• Fully hinged locking door is made of impact resistant, wireless signal transparent, ABS plastic
• Cabinet size: 22” x 22” x 4” deep
• Cabinet can be mounted in any room, complies with ADA accessibility guidelines for protruding objects
Model 1082-00 includes:
• (3) adjustable shelves
• (10) plastic cable tie downs
• 100” of Velcro strap
• (2) door keys
• Installation instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Wall Mount Enclosures
BIM, CAD, and CSI Specifications
Model 1022-00
The Model 1022-00 wireless LAN access point enclosure is a locking, wall-mounted enclosure, designed to
accommodate access points from most manufacturers. This aesthetic, white powder coated steel enclosure
has seven knockouts for antennas and cables. The Model 1022-00 is large enough to accommodate the Cisco
1250 series, and other 802.11n, wireless access points with six antennas.
Model 1022-00 shown with (6) optional Oberon 34-ZDUAL Antennas
Specifications:
• Designed for mounting on indoor hard walls, where secure mounting is required
• Internal mounting plate accommodates access points from most manufacturers
• Antennas may be mounted externally using optional bulkhead connectors (Oberon P/N 35-BULKHD-
KIT) or Oberon 34-ZDUAL antennas. Seven knockouts for antennas.
• UL Listed
• Construction: Textured white powder-coated steel, 18 ga. backbox, 16 ga. door
• Fully hinged locking door, keyed alike
• Size: 11" x 12.5" x 5.80”, 5.30" useful depth with universal mounting plate in place
• Weight: < 7lbs
Model 1022-00 Includes:
• Mounting plate for many manufacturers access points, mounting screws and hardware
• ¾" diameter conduit connector
• Mounting instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
NEMA Enclosure for Wireless APs – Hinged Cover
BIM, CAD, and CSI Specifications
Model 1026-00
The Model 1026-00 is a compact NEMA enclosure designed to protect wireless LAN access points from most
vendors in challenging indoor/outdoor environments, such as stadiums. This rugged polycarbonate enclosure
protects the access point from weather, dust, and impacts, and is transparent to wireless signals, so access
points with body integrated antennas or small detachable antennas may be protected. The enclosure has a
fully hinged cover, molded in padlock hasps for locking, & interior mounting plate for attaching access points.
Enclosures with clear covers are available. Please contact your Oberon representative.
Specifications:
• Designed to NEMA 3R, 4, 4X, 12, and 13, and IEC529-IP66 specifications for indoor/ outdoor wet, dirty,
or corrosive environments. UV stabilized for exposure to direct sunlight.
• UL listed to UL50 and UL508A. Back box and cover are light gray UL94-5VA polycarbonate plastic
• Transparent to wireless signals
• Wall mounting holes are outside the sealed area, preventing ingress of moisture and dust
• Cover is fully hinged. Cover can be latched and/or screwed tight and locked with padlock (not included)
• Wireless access point max. operating temperature should be de-rated by 9 °C in the 1026-00
• Interior size: 12” x 10" x 6” deep. Other sizes available, please contact your Oberon representative
• Weight: 4 lbs
• Smoked clear polycarbonate cover is available upon request. Please specify as “-C” in model number
Model 1026-00 Includes:
• Interior universal mounting plate for wireless access points
• Wall mounting brackets
• Installation Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Stadium NEMA Enclosure for Wireless APs – Screw on Cover
BIM, CAD, and CSI Specifications
Model 1021-00
The Model 1021-00 is a compact NEMA enclosure designed to protect wireless LAN access points from most
vendors in challenging indoor/outdoor environments such as stadiums. This rugged polycarbonate enclosure
protects the access point from weather, dust, and impacts, and is transparent to wireless signals, so access
points with body integrated antennas or small detachable antennas may be protected. The enclosure has a
screw on cover and interior universal mounting plate for attaching access points. Enclosures with clear covers
are available. Please contact your Oberon representative.
Specifications:
• Designed to NEMA 1, 2, 4, 4X, 12, and 13, and IEC529-IP66 specifications for indoor/ outdoor wet,
dirty, or corrosive environments. UV stabilized for exposure to direct sunlight.
• UL listed to UL508. Back box and cover are light gray UL94-5VA PBT/PC blended plastic
• Transparent to wireless signal
• Wall mounting holes are outside the sealed area, thus preventing ingress of moisture and dust
• Cover attaches with 4 large captured plastic screws, gasket is gray poly-urethane
• Wireless access point max. operating temperature should be de-rated by 9 °C in the 1021-00
• Interior size: 10” x 12.4" x 4.8” deep. Other sizes available, please contact your Oberon representative
• Weight: 3.4 lbs
• Clear polycarbonate cover is available on request. Please specify “-C” in model number
Model 1021-00 Includes:
• Interior universal mounting plate for wireless access points
• Wall mounting brackets
• Installation Instructions
Oberon, Inc. ● 1315 S. Allen Street ● State College, PA 16801 ● Phone (814) 867-2312 ● Fax (814) 867-2314 ● www.oberonwireless.com
Compact Stadium NEMA Enclosure for Cisco Wireless APs
BIM, CAD, and CSI Specifications
Model 1020-PS
The Model 1020-PS is a compact NEMA 4 enclosure designed specifically to protect Cisco 1140/1260/3500
series wireless LAN access points in challenging environments such as stadiums. This rugged polycarbonate
enclosure protects the access point from weather, dust, and impacts, and is transparent to wireless signals, so
access points with body integrated antennas or small detachable antennas may be protected. This is the
smallest NEMA enclosure for Cisco access points and is ideal for under seating installation.
Model 1020-PS shown with Cisco 1260 wireless access point and Cisco Antennas
Specifications:
• Designed to NEMA 1, 2, 4, 4X, 12, and 13, and IEC529-IP66 specifications for use in indoor/outdoor
wet, dirty, or corrosive environments. UV stabilized for exposure to direct sunlight.
• UL listed to UL508. Light gray back box and cover are UL94-HB rated PBT/PC blended plastic
• Transparent to wireless signal
• Cover attaches with six M-4 stainless steel screws, silicon sponge gasket material provides seal
• Cover screws must be torqued to 8 in-lbs
• Wireless access point max. operating temperature should be de-rated by 11 °C in the 1020-PS
• Interior size: 11.5” x 8.8" x 3.1” deep. Other sizes are available, please contact your Oberon
representative
• Weight: 3 lbs
Model 1020-PS Includes:
• Interior universal mounting plate for Cisco access points
• (2) Right angle mounting brackets, pre-installed
• Installation instructions