INSTRUCTION BOOK

INDEX

Features and Parts .

Needle and Thread Chart.

Inserting of the Needle.

Winding of the Bobbin ..

Threading of the Bobbin Case .

Placing Bobbin Case in Shuttle.

Upper Threading .

Straight Stitching.

Setting the Stitch Length .

Sewing in Reverse .

Adjusting the Tensions .

Feeding of Fabric.

Sewing Thin or Light Weight Fabrics

Darning and Monogramming .

Removing of the work .

Setting the Needle Position.

Embroidery Sewing.

Stitch Patterns .

Manual Zigzag Stitching .

Blind Stitch Hem.

Sewing on Buttons .

Button Holes .

Embroidering with a Hoop .

Narrow Hemmer .

Sewing Braid.

Quilting Guide .

Seam Gauge or Cloth Guide .

Adjustable Cording and Zipper Foot

How to Oil your Machine .

Cleaning and Oiling the Shuttle .

Accessories.

Check up for Smooth Sewing.

Names of Parts.

Page

... 2—3

... 3~4

. 4 ... 4~5 . 5 . 6 ... 6 — 7 . 7 . 7 . 7 . 8 . 8 . 9 . 9 . 9 . 10 10-12

. 11 12-13

. 13

. 14 14-15

. 16 16-17

. 17

. 17

. 18

. 18 18-19

. 19

. 20

. 21 22-28

1

FEATURES AND PARTS (Front View)

1. Thread Take-up Lever

2. Pressure Release (Darning)

3. Arm Thread Guides

4. Pattern Indicator

5. Needle Positioning Lever

6. Zigzag Width Indicator

7. Zigzag Width Control

8. Bobbin Winder Spindle

9. Hand Wheel

10. Stitch Length Indicator

11. Stitch Length Regulating Dial

Fig. 1

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

Drop Feed Buttons

Push Button Reverse

Decorative Stitch Pattern Dial

Tension Regulator

Needle Clamp

Presser Foot

Needle Plate

Bobbin Cover Plate

Presser Foot Thumb Screw

Thread Bar and Guide

Face Plate

FEATURES AND PARTS

(Back View)

Fig. 2

23. Lamp Switch 24. Presser Bar Lifter 25. Thread Cutter

26. Feed 27. Head Hinge Mounting Holes 28. Spool Pins

29. Top Plate

NEEDLE-THREAD-FABRIC-STITCHING GUIDE

Needle Fabric No.

Extremely heavy tarpaulin, sacking, 19 canvas, duck etc.

Heavy upholstery fabric, ticking, 18 denim, leatherette

Medium heavy drapery fabric, velveteen, 16 suiting, felt, terry etc.

Medium broadcloth, percale, gingham, linen, ^4 chintz, taffeta, sheer wool, shantung etc.

Machine Stitches Per Inch

Cotton Thread

Mercerized Thread

6 10 to to Heavy Duty 8 30

8 30 to to Heavy Duty 10 40

10 40 to to Heavy Duty 12 60

12 60 to to 50 14 80

Silk or

Nylon

A

3

Sheer voile, lawn, dimity, crepe, handkerchief linen, plastic film etc.

ii

14 to 16

(Plastic film) 8 to 10

80 to

100 50 A

Very sheer chiffon, 16 100 batiste, lace, organdy, 9 to to 50 A ninon, net, marquisett etc. 20 150

INSERTING THE NEEDLE

Fig. 3

See Fig. 3. Raise the needle bar (!)

to its highest point, turning hand

wheel toward you by hand. Then

loosen the needle clamp screw (2) and

the needle can be inserted into clamp

(D. 9 flat side Place needle (Fig. 4, flat side to

right) in the needle clamp and push

it upward as far as it will go into the

needle clamp hole, tightening the

needle clamp screw securely with a

screw driver.

After changing the needle make one complete revolution of the hand wheel by

hand to be sure the needle is in the correct position.

Fig. 4

WINDING THE BOBBIN

A\

3.

To wind the bobbin the hand wheel must be disconnected from the stitching

mechanism. Hold the hand wheel with your left hand, turn the stop motion

knob toward you with your right hand. This

will permit the hand wheel to turn freely while

the needle bar remains motionless. The hand

wheel is now disconnected for the bobbin

winding operation (Fig. 5).

Place a spool of thread on the spool pin and

lead thread between the arm thread guides on

the top plate.

Now wind the end of the thread around an

empty bobbin seven or eight times and place

the threaded bobbin on the spindle of the

bobbin winder Fig. 5

4

4. By pressing on the bobbin winder lever, the small rubber wheel is brought

into contact with the hand wheel. To lock it in position, press the bobbin

winder lever until a click is heard. The bobbin winder release latch is in

contact with the shaft of the bobbin. It holds the bobbin in place.

5. Now press your foot control or knee control, and when the bobbin is com¬

pletely full, it will be released

and stop turning, detach the

bobbin from the spindle. Hold

the hand wheel firmly with

your left hand, and with your

right hand turn the stop mo¬

tion knob way from you until

it can not be moved any

farther, and the needle bar

moves with the turning of

the hand wheel. Fig. 6

THREADING THE BOBBIN CASE

Step 1 (illustrated in Fig. 7). Hold bobbin case between thumb and forefinger

of left hand, so that the slot in the edge of the bobbin case is on top. Take

the bobbin between thumb and forefinger of right hand so that the thread on

top leads from left to right.

Step 2. Insert bobbin into bobbin case, pull the thread into the slot of the

bobbin case as shown in Fig. 8, and draw it under the tension spring and into

the delivery eye as shown in Fig. 9.

Fig. 7 Fig. 8 Fig. 9

5

PLACING BOBBIN CASE IN SHUTTLE

Open bobbin cover plate to left of the needle. See Fig. 10. Hold the bobbin

case latch (T), between the thumb and forefinger of the left hand, with at least

three inches of thread running from the top of the bobbin case to the right.

Insert and center the bobbin case on the stud

of the shuttle body (2). Be sure the bobbin case

finger (3) is opposite shuttle race notch (4).

Press the bobbin case (5) into the shuttle as

far as possible until latch catches on the center

post of the shuttle. THEN release the bobbin

case latch ®. Press bobbin case again after

latch has been released to make sure the bobbin

case is locked securely in place. Close the

Fi

Hold the end of upper thread loosely and

turn hand wheel toward you until the needle

goes all the way down and comes back up.

A loop (Fig. 12) will be formed over the

upper thread which then can be pulled out

straight. Place both thread ends under the

slot of the presser foot and draw toward the

back of the machine, leaving both threads

three or four inches long.

move zigzag toot, nepiace wun mngeu. v-

narrow foot and tighten screw securely. Fig. 13

To change needle plate remove screws and slide the bobbin case cover and replace the zigzag needle pla

for straight sewing, while raising the needle bar and the presser

highest points. (1) First align the "SELECT" on the zigzag width control ® (Fi

the indicator, then align the manual pattern ( |^ ) on the dec

pattern dial ® with the indicator and return the zigzag wid

"0" position. (2) Set needle positioning lever © at extreme left hand position

(3) Select desired stitch length on dial ©. can be performed. (4) Push the button © and reverse stitching

SETTING THE STITCH LENGTH The length of the stitch is regulated by the stitch length regulating dial ®

(Fig. 13). Near 0 is the shortest stitch and 5 is the longest, but the dial may

be set at any spot between markings for a variety of lengths. Turn the dial to

the right to lengthen and to the left to shorten the stitch.

STITCH LENGTH CHART (Approximate)

Figures on indicator 0 i 2 3 4 5

Number of stitches per inch No Feeding 30 15 10 7 6

SEWING IN REVERSE "When you wish to sew backward to tie the threads at the beginning or end

of a seam, press in button © (Fig. 13) as far as it will go. The machine

will sew backward as long as the button is held in.

7

ADJUSTING THE TENSIONS

Always adjust the upper tension with the

presser foot down, as the tension is released

when it is raised. To increase the tension on

the upper thread, turn regulator (Fig. 14) to

the right. To decrease, turn to the left. The

higher the number on the regulator the

tighter the tension.

Before adjusting lower tension be sure that the machine is threaded properly.

When necessary to change the bobbin tension, turn small screw (Fig. 15) on

side of the bobbin case clockwise to tighten, counterclockwise to loosen.

When the upper and lower tensions are

properly balanced, a perfect stitch will be

formed with both threads interlocking in

fabric (Fig. 16).

When the upper tension is too tight, the

lower thread is pulled up over the upper

thread which is lying flat on the fabric

(Fig. 17).

When the upper tension is too loose, the

upper thread forms loops over the lower

thread lying flat under the fabric (Fig. 18).

Fig. 16 Fig. 17 Fig. 18

FEEDING OF FABRIC

The height of the feed dog may be regulated according to the thickness of

the material being sewn, by proper setting of the push buttons (Fig. 19).

1. In sewing on thin materials, such as silk,

creape de chine etc., push the button

marked "DOWN" down as far as the red

line.

2. In sewing on thick materials, such as

overcoats, push the button marked "UP"

down as far as it will go.

3. When it is necessary to turn the work

freely as in embroidering and button

sewing, push the button marked "DOWN"

as far as it will go. Fig. 19

8

PUSH

SEWING THIN OR LIGHT WEIGHT FABRICS

When lighter pressure is required to sew satisfactorily on thin silk or filmy

material, the pressure cap should be about halfway down.

Release all the way by pressing the snap lock ® (Fig. 20), and then press

cap (2) (Fig. 21) down again to halfway spot.

Fig. 20 Fig. 21

DARNING AND MONOGRAMMING

In order to move the fabric freely in any direction for darning, mending and

certain kinds of free-hand embroidery, release the cap (2) (Fig. 21) completely

by pressing down on the snap lock ® (Fig. 20). Press “DOWN" button all the

way down, which drops the feed well below the needle plate. To return feed to

normal, press "UP" button, Push cap down. (Fig. 21)

REMOVING THE WORK

Be sure to stop the machine when the thread take-up lever and needle bar are

located at the highest position. Now raise the presser foot and draw the fabric

back and to the left, Fig. 22 and 23, and pass the threads over the thread

cutter. Pull down slightly holding thread in both hands, so as not to bend the

needle. Leave the ends of thread under the presser foot.

SETTING THE NEEDLE POSITION

The needle bar should be at its highest

point when adjusting needle position to

avoid tearing the fabric or bending the

needle.

Set the needle positioning lever to

right, middle or left for corresponding

needle position.

L Indicates the left hand needle position.

M Indicates the middle needle position.

R Indicates the right hand needle position.

All straight stitching to be done using straight

stitch needle plate and presser foot. The needle

positioning lever must be in the left position (L).

The needle positioning lever set in any other position will cause the needle

to break. The various needle positions are used with the decorative stitch

patterns and when doing creative embroidery.

EMBROIDERY SEWING

This sewing machine is so designed

that the patterns indicated on the pattern

dial can be sewn. In sewing the red

patterns in the outside circle of the

pattern dial the needle position of "L" is

used, in sewing the blue ones in the

outside circle that of "R" is used, and

in sewing the green ones in the inside

circle that of "M" is used. In each case

the graduation "0" on the zigzag width

control is aligned with the indicator.

In pattern selection align your desired pattern with the indicator after select

the zigzag width control to "SELECT".

(Never turn the decorative stitch pattern dial clockwise from [] pattern or

counterclockwise from pattern indicated on pattern plate.)

Fig. 26

L M R Fig. 25

- 10 -

How versatile your machine is will become apparent with practice, as just

changing zigzag width control and needle positioning lever will do the following.

Zigzag Width

Needle

Position

0 l

CV

] oo

4 5

L WMP*f! mmmm M mjfmrmlffm mmmm rnmmm R mSmwikm mMmM mmmm

Fig. 27

Increasing the stitch length slightly will stretch the pattern.

^MA/WuaA^^

Fig. 28

STITCH PATTERNS

PATTERN

NEEDLE POSITION

n It N!> t t t

it ][ $ I ♦

L M R L i M R LMR LMR LMR LMR

STITCH

WIDTH

PATTERN ir t o 0 4 ii k 1 \

NEEDLE POSITION L M R L M R L M R L M R L M R L M R

STITCH

WIDTH

0 \ j t

<

i T j j j l J [ ; : h J J

1 1 1 j t j 1 { j [ j j j j l j V s i 2 f 1 j t 1 ! [ j ] i; \ j [ E

>

>

MANUAL ZIGZAG STITCHING

(1) First align the "SELECT" on the zigzag width control with the indicator,

then select manual pattern ( ) by turning the decorative stitch pattern

dial and return zigzag width control at number "0" position.

(2) Set the stitch length regulating dial, the zigzag width control and needle

positioning lever as you wish.

(3) The varied patterns are available by changing the position of the zigzag

width control and that of the needle positioning lever (Fig. 29).

(4) When the zigzag width control is manually turned as you operate the

machine, such free patterns as are shown in Fig. 30. Result.

(5) The patterns available by alternately changing the needle positioning

lever with the zigzag width control set to a certain width, are shown in

Fig. 31.

— 12 -

I

ZIGZAG

WIDTH

L M

NEEDLE POSITION

ZIGZAG

WIDTH

MANUAL

OPERATION

5 i

L M R NEEDLE POSI TION

Fig. 29 Fig. 30

NEEDLE

POSITION

2 0

STITCII WIDTH

Fig. 31

BLIND STITCH HEM & DECORATIVE STITCH

(1) Use standard zigzag foot and needle plate.

(2) First align the "SELECT" on the zigzag width control with the indicator,

then select the blind stitch pattern (

SEWING ON BUTTONS

(1) Remove presser foot and replace with special purpose button sewing foot

(Fig. 34).

(2) Push drop feed button marked “DOWN” down all the way.

(3) First align the “SELECT” on the zigzag width control with the indicator,

then select the manual pattern () by turning the decorative stitch

pattern dial.

(4) Set needle positioning lever in the middle position “M“.

(5) Place the button so that this left hole comes directly under the needle.

Then gently lower the presser foot.

(6) Turn the zigzag width control (produce a zigzag stitch) until the needle

goes through the right hand hole of the button. Turn the hand wheel

slowly by hand to be sure the needle clears both holes in the button

Correct width if necessary.

(7) When needle goes into the center of each

hole, run the machine at a medium speed,

making five or six stitches, stopping with

the needle in the left hole.

(8) To lock the zigzag stitch and prevent

ravelling, return the zigzag width control

at number “0“ and take a few stitches in

the same hole. If you wish, you may

place a rounded toothpich over the button

between the two holes, and sew button to

fabric in the regular way. Remove the

toothpich and wind thread under button Fig. 34

forming a shank. Fasten.

Apply the above method to sew on buttons with four

holes, hooks, snaps, etc..

If a four hole button is to be sewn follow the same pro¬

cedure above for the two hole button.

Now lift presser foot slightly and move fabric to permit

stitching the remaining two holes.

Hooks, snaps, etc., are sewn to the fabric with the same

procedure as for sewing the two hole button.

Fig. 35

BUTTON HOLES A buttonhole can be made in any length within the range

of limited widths. To establish the correct length buttonhole required add

1/8 inch to the cutting space for bar tacks.

To obtain the length of the cutting space, the opening

through which the button passes is measured by adding the

width (A) of the button Fig. 36. Fig. 36

14 —

Mark the beginning and end of the buttonhole on fabric with a basting line

or tailor's chalk.

Make one on scrap fabric following directions below to be sure machine

adjustments are correct.

1. Replace presser foot with special purpose

button hole foot. It provides maximum

visibility and allows closely spaced stitch¬

es to feed evenly (Fig. 37).

2. First align the "SELECT" on the zigzag

width control with the indicator, then set

decorative stitch pattern dial at number

1 position for forward stitching of button¬

hole and return zigzag width control to

"0" position. (Never turn the decorative

stitch pattern dial clockwise from [j

pattern or counterclockwise from

pattern indicated on pattern plate.)

3. Set needle positioning lever in the extreme

left hand position "L".

4. Set stitch length at number "1/2" between

"0" and "1". (When the left side pitch is

different from the right side pitch, adjust

the pitch by means of the stitch length

control, so that pitches on both sides will

be the same.)

5. Stitch the length of the buttonhole.

6. With needle out of fabric, turn the decora¬

tive stitch pattern dial to the right, to the

illustration showing lower bar tack of

buttonhole. Take 3 or 4 stitches in fabric.

7. Remove needle from fabric, and turn the

decorative stitch pattern dial to the right,

to the illustration showing right side of

buttonhole. Now the machine will stitch

the right side in reverse.

8. Remove needle from fabric, turn the

decorative stitch pattern dial to the left,

to the illustration showing bar tack of

buttonhole. Stitch the same as lower bar

tack.

Fig. 37

4

4 Steps in

Making Button

Hole

Fig. 38

Fig. 39

Slit the buttonhole between the two rows of stitching with the buttonhole

cutter or seam ripper. Be careful not to cut the stitching or bar tacks.

If you plan to make buttonhole on sheer or soft material, place tarlatan or

paper under fabric which can be torn away. After stitching.

— 15 -

EMBROIDERING WITH A HOOP

It is easy to follow a stamped design or

to work free hand when embroidering or

monogramming. Release the pressure from

the foot by pressing down the snap lock

on the darner. Push the drop feed button

marked "DOWN" down all the way.

Stretch the fabric in an embroidery hoop,

and place under the needle after removing Fig' 40

the presser foot. Set the zigzag width at the size you prefer and lower the

presser bar lifter. Then operate the machine at a rather high speed while mov¬

ing the hoop slowly with both hands. Work carefully and be sure to keep fingers

out of the path of the needle.

Should you encounter skipped stitches, the fabric is not stretched tight enough or

a darning spring is needed.

NARROW HEMMER

With the needle at it highest position, replace regular presser foot with narrow

hemmer being sure to tighten it securely in place. Align the "SELECT" on the

zigzag width control with indicator. Set decorative stitch pattern dial at manual

pattern ( ) , needle positioning lever in the left hand position "L , zigzag width

control at "0" position for straight stitched hem or at number "3" for zigzag

stitched hem. Set stitch length to suit. For general hemming, cut the right cor¬

ner of the material to be sewn diagonally,

and prepare the material so that it can be

rolled easily. Then insert it into the scroll

of hemmer. Pull out the material to the

point just beneath the needle, so that it

can continue being rolled in the scroll.

Then lower the presser bar and sew 2 or

3 stitches slowly and carefully, holding

the beginning of the hem between your right thumb and forefinger and sew in

order that the edge of material can be scrolled nicely by adjusting, and the

sewing result will be as given in the illustration. Be careful not to feed too

much or too little material into the hemmer (Fig. 41).

Fig. 41

When hemming and sewing on lace

is required in one operation, proceed

to make a hem in the same manner as

explained above. Insert edge of lace or

trimming (be sure the right side is down)

into the slot on the right side of the

hemmer. Make sure that the needle pierces

it close to the edge just above the turned

edge of the hem. Begin to stitch, leading

the lace edge into the hemmer's slot with the right hand while guiding the

material being hemmed into the scroll of hemmer with the left hand. To apply

lace in the "French Manner," insert the fabric to be hemmed as for plain hemm¬

ing, with the right side up. Insert the lace from the left, with the right side

down, and put it on top of the fabric. Then put the lace and fabric combined

into the hemmer and the hem can be made to enclose the lace edge in one

stitching (Fig. 42).

SEWING BRAIDS Remove the ordinary presser foot from

the machine and attach the braiding foot,

as shown in Fig. 43. Introduce braid

through the small hole of the spring on

foot. Set the needle positioning lever in the

extreme left hand position "L". First align

the "SELECT" on the zigzag width control

with indicator, then align the manual

pattern () indicated on the pattern

dial. Adjust the width of zigzag seam and

the length of stitch to obtain such a

covering of the braid as appears most desirable for the material you are sewing.

Using some threads of contrasting colors will enhance the beauty of your braiding.

QUILTING GUIDE This guide for making parallel rows of

stitching is attached by placing the pronged

holder between the presser foot and the

presser foot clamp screw (Fig. 44). Adjust

the curved bar to press lightly on the

fabric. By letting the guide ride on the

first stitching line, successive rows will be

an equal distance apart.

When the bar is attached so that the

curved part is to the right of the needle,

it may also serve as a seam width guide.

Fig. 43

Fig. 42

— 17

SEAM GAUGE OR CLOTH GUIDE

Use the seam gauge as a guide for

straight seams and even rows of top

stitching along edges of fabric. Fasten

gauge with accompanying screw in

threaded hole in bed of machine (Fig.

45). Adjust to seam width desired.

THE ADJUSTABLE CORDING AND ZIPPER FOOT This attachment is used

to make and insert covered

cording, and to sew in

zippers. Loosen thumb

screw to slide foot to

either right or left of

needle.

CORDING. Fold bias

strip of fabric over cord.

Loosen thumb screw and ....-_

set foot so needle is Fig' 46 Fig‘ 47

centered in needle hole. Machine baste cord in place (Fig. 46^47).

To sew covered cord to material, reset adjustable foot so needle stitches closer

to cord,and on edge of base fabric.

SEWING IN ZIPPER

Loosen thumb screw and slide foot so needle

enters center of needle hole. Guide metal of

zipper along edge of foot (Fig. 48). Stitching

should be close to zipper to allow easy opening

and closing. Adjust to sew from either right or

left side, which ever is move convenient.

CARE AND MAINTENANCE OF YOUR MACHINE HOW TO OIL YOUR MACHINE

Your machine should be oiled occasionally to keep it oporating smoothly. How

often depends on the amount of sewing you do.

Before oiling the upper part of the sewing unit at points indicated by arrows in

Fig. 50, turn hand wheel toward you until the take-up lever is at its lowest point.

Avoid over-oiling. Only a drop is needed at each point.

To oil parts under the bed of the machine, tip the unit back on its hinges

and apply a drop of oil at each point indicated in Fig. 51.

To oil moving parts inside the face plate, which only rarely require oiling,

open plate and oil at spots indicated in Fig. 49.

Fig. 48

— 18 —

Fig. 50

Fig. 49 Fig. 51

CLEANING AND OILING THE SHUTTLE (See Fig. 52)

The stitch forming mechanism occasionally becomes clogged with loose threads

and lint. This will interfere with the efficient operation of the machine. Cleaning and

removal of the lint will safeguard the performance. To remove the shuttle

assembly, proceed as follows : 1. Turn the hand wheel until the needle reaches its highest position. Tilt

head back on its hinges.

2. Remove bobbin case (A), Fig. 52.

3. Turn the two shuttle race cover clamps (B) outward and remove the

shuttle race cover (C) and shuttle body (D).

4. Clean the shuttle race, the shuttle, and shuttle race cover by removing all

threads, lint, etc.

5. Apply a drop of oil with finger tip to outer edge of shuttle.

When the cleaning has been completed, proceed as follows to replace the

shuttle assembly :

1. Turn the hand wheel until the needle

reaches its highest position.

2. Place shuttle body (D), against shuttle

driver and adjust into position.

3. Replace shuttle race cover (C), fitting pin

at lower edge into notch, and lock into

position with shuttle race cover clams (B),

making certain the clamps have been

snapped securely into position.

4. Put bobbin case into the shuttle race.

5. Put the bobbin case into the shuttle race,

fitting tongue into notch (E) of race cover.

— 19 -

ACCESSORIES

1„ Large Screw Driver

2. Small Screw Driver

3. Button Hole Cutter (Ripper)

4. Plastic Oiler (Sealed and filled)

5. Package of Needles

6. Bobbins (3)

7. Felt Washers (2)

8. Quilting Guide

9. Cloth Guide and Thumb Screw

10. Straight Stitch Needle Plate

11. Presser Foot for Straight Stitch

12. Embroidery Spring

13. Braiding Foot

14. Button Sewing Foot

15. Buttonhole Foot

16. Narrow Hemmer Foot

17. Cording and Zipper Foot

CHECK UP FOR SMOOTH SEWING

Although your sewing machine is designed for maximum efficiency, should any

of the following difficulties occur they can be remedied with minor adjustment.

Upper Thread Breaks-

Be sure needle is inserted properly.

Check on correct way to thread machine.

Use correct needle size for thread.

Do not have upper tension too tight.

Lower Thread Breaks-

Check correct method of threading bobbin case.

Be sure lower tension is not too tight.

Needle Breaks——

Do not tug or pull on the fabric while sewing as this will bend and eventually

break the needle.

Be sure presser foot is firmly attached to bar.

Skipped Stitches

Do not use a blunt or bent needle.

Insert needle correctly.

Use correct needle size for thread.

Be sure pressure on foot is sufficient when sewing heavy fabrics. •

Stitches Loop-

Make sure tensions are properly balanced and that machine is threaded

correctly.

Machine Binds-

Clean thread, dust and lint from hook, shuttle and race.

If condition continues, it may be that the machine is gummy with oil. Apply

kerosene to oil holes, run rapidly for a while, and wipe dry. Then lubricate

again with fine sewing machine oil.

— 21 —

Names of Parts

Parts. No.

Item. No.

Name of Parts Parts.

No. Item. No.

Name of Parts

213 SK-86 Crank Rod Hinge Tapered 267 606B-58 Reverse Push Button

Screw W/Nut 268 606B-59 Reverse Push Button Link

214 322B-56 Drop Feed Button (Comp.) 269 SZm-69-9 Setting Terraced Screw for

215 322B-56-13 Drop Feed Plate No. 268

216 322B-56-14 Setting Screw for No. 215 270 420B-100-3 Setting Screw for No. 269

217 9/64 Nut for No. 216 271 1/8 Nut for No. 270

218 Z-131-4 Setting Terraced Screw for 272 SK-98 Spool Pin

No. 220 273 SKH-69-16 Nut for No. 272

219 SLUI-22-6 Vinyl Washer for No. 218 274 413B-31 Spool Pin Bracket

220 SWR-3 Drop Feed Connecting Rod 275 SSZ-100-7 Setting Screw for No. 274

221 Drop Feed Body (Comp.) 276 606B-49 Bobbin Winder (Comp.)

222 606B-12 Face Plate 277 421B-31 Setting Screw for No. 276

223 SL11-136 Lamp Cord Clamp 278 SK-122 Rubber Ring for No. 276

224 SL-311-1 Setting Screw for No. 223 279 420B-17 Hand Wheel

225 SZIV-14 Face Plate Spring 280 SK-43A Stop Motion Clamp Washer

226 420B Setting Screw for No. 225 281 SK-42 Stop Motion

227 SSZ-100-6 Lamp Signal 282 SK-44 Stop Motion Small Screw

228 Z-171-1 Face Plate Hinge

229 SSZ-72-3 Setting Screw for No. 228

230 Z-174 Thread Guide Plate

231 SSZ-100-7 Setting Screw for No. 230

232 SZVI-14a Lamp Socket Setting Plate

233 Lamp Socket Setting Screw

234 420B Setting Screw for No. 232

235 606B-64 Lamp (Comp.)

236 Tension Regulator (Comp.)

237 SL-103-1 Setting Screw for No. 236

238 Z-40 Lamp Cord Clamp

239 SL-311-1 Setting Screw for No. 238

240 606B-11 Top Plate

241 SSZ-67-2 Setting Screw for No. 240

242 606B-52 Arm Thread Guide (Rear)

243 SK-111A Setting Screw for No. 242

244 327B-20 Arm Thread Guide (Front)

245 318B-24 Setting Screw for No. 244

246 AZB-13-3 Nut for No. 245

247 328B-24 Pattern Selector Indicator

248 606B-51 Needle Position Indicator Plate

249 606B-15 Zigzag Plate

250 SK-92-3-1 Setting Screw for No. 249

251 606B-21 Decorative Stitch Pattern Dial

252 SK-11 Setting Screw for No. 251

253 606B-22 Decorative Stitch Pattern Plate

254 606B-24 Circular for Pattern Dial

255 606B-23 Vinyl Plate for Pattern Plate

256 SZBH-25 Ring for No. 251

257 SK-130 Zigzag Width Indicator

258 606B-40 Zigzag Width Control Dial

259 SK-11 Setting Screw for No. 258

260 606B-41 Zigzag Width Illustrating Plate

261 328B-24 Stitch Length Indicator

262 606B-56 Setting Plate for No. 264

263 SK-80 Setting Screw for No. 262

264 606B-54 Stitch Length Regulating Dial

265 STR-14 Setting Screw for No. 264

266 606B-53 Stitch Length Illustrating Plate

PRINTED IN JAPAN