diamond products us - icon f17 & f20 (dp80317, dp80320)diamondproductsus.com › wp-content ›...
TRANSCRIPT
IMPORTANT: READ OPERATOR'S MANUAL CAREFULLYPlease fill out & return your warranty card!
OPERATOR'S MANUAL
ICON F17 & F20 LOW-SPEED BUFFERS
DP80317 & DP80320
Diamond Products www.diamondproductsus.com Printed in the U.S.A.
Warranty Information
Welcome…and congratulations on the purchase of your Diamond Products US product. This instruction manual is a guide for operating and servicing your unit. Read this manual completely before operating this unit.
Proper operation and service are essential to the efficient functioning of this unit. When maintained correctly, this unit will have a long, trouble-free life. Any questions pertaining to operating or servicing this unit should be directed to your nearest dealer.
Information in this document is subject to change without notice and does not represent a commitment on the part of Diamond Products US.
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
Warranty InformationThank you for purchasing a Diamond Products US product. Warranty registration is quick and easy.
Your registration will allow us to serve you better over the lifetime of the product.
To register your product, email your warranty card information to: [email protected]
-2- Operator's Manual Diamond Products
SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONSGeneral –This floor – finishing machine shall begrounded while in use to protect the operatorfrom electric shock. The machine is providedwith a three –conductor cord and a three contactgrounding type attachment plug to fit the propergrounding type receptacle. The green [or greenand yellow] conductor in the cord is thegrounding wire. Never connect this wire to otherthan the grounding pin of the attachment plug.
This machine is for use on a nominal 120-Voltcircuit and has a grounding plug that resemblesthe plug illustrated in figure below. Make surethat the machine is connected to an outlethaving the same configuration as the plug. Noadapter should be used with this machine.
This machine is intended for Commercial use. Itis constructed for use in an indoor environmentand is not intended for any other use. Use onlyrecommended accessories.
All operators shall read, understand andexercise the following safety precautions:
- Unless trained and authorized.- Unless you have read and understand
operators manual.- In flammable or explosive areas.- With a damaged cord or plug.- If not in proper operating condition.- In outdoor areas.- In standing water.- With the use of extension cords.
2] Before operating machine:- Make sure all safety devices are in place
and operate properly.
3] When using machine:- Do not run machine over cord.- Do not pull machine by cord or plug.- Do not pull cord around sharp edges of
corners.- Do not unplug by pulling on the cord.- Do not stretch cord.- Do not handle plug with wet hands.- Keep cord away from heated surfaces.- Report machine damage of faulty
operation immediately.
4] Before leaving or servicing machine:- Turn off machine.- Unplug cord from outlet.
5] When servicing machine:- Unplug cord from outlet.- Use manufacturer supplied or approved
replacements parts.
1] Do not operate machine:
-3- Operator's Manual Diamond Products
Operation of Floor Machine* Read operators manual thoroughly prior to
operating or servicing this machine.
GENERAL USE
1] Remove any obstructions or otherobstacles in the area which is to be cleaned.
2] Place the handle in the upright position andtilt machine back until handle rests on thefloor.
� Be sure the machine is not pluggedinto an outlet.
3] Attach the pad driver or brush to the machineby placing the clutch plate over the gearboxhub and turning the driver / brush 1/4 turn.
4] Place machine back into its upright position.5] Plug power cord into grounded outlet.
* Never use an extension cord inconjunction with the standard power cord.
6] The handle height may be adjusted bylifting up the compression handle which islocated on the right side of the handletube about 1 foot above floor level.Release the compression handle andadjust handle to safe operating height,then push back down on the compressionhandle to lock the handle in operatingposition.
7] To start the machine, press the red safetybutton on the top of the upper switchhousing, and then squeeze either of theoperating triggers. [the safety button mustbe depressed prior to squeezing theoperating triggers].
8] When the machine is in operation, bothhands should be placed on the switchhousing [upper handle].
9] During operation, to make the machine goright, gently raise the handle. To make themachine to left, gently lower the handle.
10] To stop the machine at any time, simplyrelease the operating trigger [s] and the machinewill stop automatically.
MAINTENANCE
To keep the machine performing well for manyyears, please follow the following maintenanceprocedures.
* Always confirm that the machine isunplugged prior to performing anymaintenance or repairs.
1] Unplug machine as soon as you are doneusing it.
2] Tilt machine back and remove pad driver orbrush.
*Never store a low speed machine with thepad driver or brush mounted to themachine
3] Clean the outside of the machine with a mildcleaner.
4] Check power cord for any damage. Ifdamage is detected, replace the cordimmediately.
5] Lubricate wheels with a water resistantlubricant once a month.
6] Check machine for loose or missing nuts andbolts, and replace as necessary.
7] If the machine is used in a dusty environment,you may remove the motor cover and blowthe motor clean with compressed air. Thiswill ensure proper ventilation, and allow themotor to run cooler.
STORAGE1] Unplug machine from power source and wrap
cord on handle.2] Tilt machine back and remove pad driver or
brush.3] Store machine in upright position and in a dry
area.
-4- Operator's Manual Diamond Products
Make sure actual cord wrap faces to the left of the machine when you are standing behind it.
1)
Push the two handle brackets backward so they lean against the rear wheel.
2)
-5- Operator's Manual Diamond Products
-6- Operator's Manual Diamond Products
HANDLE GROUP
DIANO
PARTNUMBER
NOREQ'D
1 VF30016 1
2
VF300152 1
3 VF30018 2
4
5
VF30017 1
6
VF45125 1
AS41901 1
8
VF50120 1
9
VF13504 1
10
VF30027 1
11
12
13
VF13493 1
14
AS312206B 1
15
16 AS312209 1
17 VF48310 2
18 AS22006S 1
19 AS22004S 1
20 VV13661 2
21 VF48309 1
22 VF45119 1
23 AS22009 1
24 GT13009 5
25 GT13008 2
26VF41004TP 1
27 GV40218 1
28 GV40209 1
29 AS312209 1
30 VF99010C 1
31 VF44203 1
32 VF14212 2
33 AS22005S 1
34 AS312203 1
35 GV40226B 1
VF13604 4
VF14222 4
LEVER,RIGHT,SWITCH
COVER
LABEL,FRONT COVER
TEETH WASHER,M5
SCREW,M5X12
SPRING,SAFETY BUTTON
SAFETY BOTTON
SCREW,M3X25
CLAMP BLOCK
CORD,POWER SUPPLY
STRAIN RELIEF,CORD
SCREW,M5X30
SCREW,M5X20
SERIAL TAG 20"
LEVER,SOLUTION
LEVER,LEFT,SWITCH
SCREW,M4X12
REAR COVER
BREAKER, CIRCUIT, 17A / A-0701HS
SWITCH ASSY
SCREW,M6X10
TUBE
FRONT COVER
HANDLE GRIP
CORD,HANDLE
PLUG PROTECTOR,SMALL MALE
GROMMET
NUT,LOCK,M10
WASHER,PLAIN
7
DESCRIPTOIN
HANDLE RELEASE
BOLT HANDLE RELEASE
WASHER,PLAIN
SCREW
VF300141 1CORD WRAP BLOCK
VF13570
VF40169
1
1
PIN
CONNECTION PLATE
36
37
38
39
40
41
1
1
1
1
1
1
VF40200
VF40001
VF40132
VF40139
VF40000
MF-VF001 SOLUTION TANK
VALVE ASSY KIT
TANK MOUNTING KIT
TANK SEAL KIT
BARB HOSE
HOSE SOLUTION
VF41194TP 1SERIAL TAG 17"
-7- Operator's Manual Diamond Products
-8- Operator's Manual Diamond Products
DIANO
PARTNUMBER
NOREQ'D
1 GT13080 SCREW, M6 X 30 42 AS312201TP PLATE,HANDLE GUIDE 13 GT13030 WASHER, PLAIN, M6 44 VF13502 45 VF30026 AXLE 16 VF30020 BRACKET, LEFT HANDLE 17 VV20274 WASHER, PLAIN, M13 48 GV40235 CLAMP BLOCK, AXLE 29 VV13621 SCREW, SELF-TAPPING, ST, M5 X 20 4
10 VA13474 SCREW, M5 X 16 511 VF13474A WASHER, PLAIN, M5 412 VF13524 WASHER, PLAIN, M8 413 VF13519 WASHER, LOCK, M8 414 GT13016 SCREW, M8 X 55 415 MF-VF002-4A SCREW, SELF-TAPPING, 1/4"-1" 616 MF-VF002-2 CLUTCH PLATE 1
MF-VF021 PAD HOLDER, 16" 1MF-VF022 PAD HOLDER, 19" 1
18 VF999802B GEAR BOX 119 VF99021 COUPLER 120 MT01102 SLEEVE 121 VF999821 BEARING,6002 LLU 122 VV13601 WASHER, LOCK, M5 623 VV13636 SCREW, M5 X 30 6
AS312101 BUMPER, 17" 1AS312204 BUMPER, 20" 1
25 YLQ19200 ROTOR WITH FAN ASSY 126 YCQ10501 BEARING ,6203 R 127 YCQ12301 CENTRIFUGAL SWITCH 128 VV20509 SCREW, M5 X 10 2
VF40101TP FRAME,17" 1VF40100TP FRAME,20" 1
30 YCQ12302 STATIONARY SWITCH 131 VF999854 RUN CAPACITOR, 50 F / 370V 132 VF40152 HOSE BARB 133 YLQ14601 MOUNTING FRAME SMALL , CAPACITOR 134 VF30019 BRACKET, HANDLE, RIGHT 135 VF13520 WASHER, LOCK 236 VF50119 WASHER, PLAIN, M12 237 VF14214 SCREW, M5 X 8 438 VF48202 WHEEL, 5" 239 VF40994 LABEL, READ MANUAL 140 VF44012 SCREW, M6 X 12.7 241 VF13666 WASHER, M6 242 VF13604 WASHER, LOCK, EXTERNAL TOOTH 443 YCQ10615 MOUNTING FRAME BIG , CAPACITOR 144 AS41902 PLUG PROTECTOR, LARGE FEMALE 145 YCQ10414 CLEAR COVER 446 YCQ10416 CAPACITOR WRAP 247 VF999805 START CAPACITOR BIG , 400-450UF/150V 148 YLQ17507 BOLT ASSEMBLY 449 VF999787 MOTOR, 110V, 1.5HP 150 VF44003 LABEL, MOTOR 151 VF44001TP TOP COVER, MOTOR 152 VF47023 BUMPER 1
DESCRIPTION
BASE ASSEMBLY
NUT, LOCK, M6
17
24
29
-9- Operator's Manual Diamond Products
-10- Operator's Manual Diamond Products