direct coupled damper actuator (spring-return type) specifications
TRANSCRIPT
AB-7143
1
Specifications/Instructions
Direct Coupled Damper Actuator
(Spring-return Type) General Model MY6055B2001 direct coupled damper actuator is a motorized actuator to open/close air damper for ventilation and air-conditioning systems. Model MY6055B2001 has the spring-return function that automatically rotates the damper shaft to the damper closing position and shuts off the damper in the event of power shutdown. This is suitable for controlling air dampers in the systems requiring high safety.
Features Spring-return mechanism rotates the damper shaft to the
damper closing direction and then stops the shaft at the shutoff position.
Torque limit function protects the motor from overload.
Manual override function enables to adjust the actuator without being powered.
Rotating direction is reversible by turning the actuator
the other way around.
Brushless DC motor stabilize the operating time regardless of the size of the load.
The actuator contains two auxiliary contacts (SPDT). SPDT: Single pole, double throw
Model Numbers Model number Specification
MY6055B2001 Direct coupled damper actuator (two-position control, spring-return type, with auxiliary switches)
AB-7143
2
Safety Instructions Please read instructions carefully and use the product as specified in this manual. Be sure to keep this manual near by for ready reference.
Usage Restrictions
This product is targeted for general air conditioning. Do not use this product in a situation where human life may be affected. If this product is used in a clean room or a place where reliability or control accuracy is particularly required, please contact oursales representative. Azbil Corporation will not bear any responsibility for the results produced by the operators.
Warnings and Cautions
WARNING Alerts users that improper handling may cause death or serious injury.
CAUTION Alerts users that improper handling may cause minor injury or material loss.
Signs
Alerts users possible hazardous conditions caused by erroneous operation or erroneous use. The symbol inside indicates the specific type of danger. (For example, the sign on the left warns of the risk of electric shock.)
Notifies users that specific actions are prohibited to prevent possible danger. The symbol inside graphically indicates the prohibited action. (For example, the sign on the left notifies that disassembly is prohibited.)
Instructs users to carry out a specific obligatory action to prevent possible danger. The symbol inside graphically indicates the actual action to be carried out. (For example, the sign on the left indicates general instructions.)
WARNING
Before wiring and maintenance, be sure to turn off the power to the product. Failure to do so might cause electric shock.
Do not disassemble the spring unit of the product. The spring unit might rapidly rotate or jump out of the actuator, resulting in serious injury.
CAUTION (1/2)
Store the products in package. Storing unpackaged products might damage or stain the products.
Do not send shock to the product. Doing so might damage the product.
Install and use the product in a location that meets the operating conditions (temperature, humidity, power, vibration, shock, mounting direction, atmospheric condition, etc.) as listed in the specifications. Failure to do so might cause fire or device failure.
Take anti-lightning measures based on regional and building characteristics. Lightning might cause fire or critical damage to the product without the anti-lightning measures.
Do not install the product in an environment with high heat radiation. High heat radiation might cause malfunction of the actuator.
Do not use the product in an atmosphere containing corrosive gas. Doing so might damage the actuator or its components.
Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.
All wiring must comply with applicable codes and ordinances.
Provide a circuit breaker for the power to the product.
Provide a circuit protector (e.g., a fuse, cut-off device) for the control panel to ensure your safety.
AB-7143
3
CAUTION (2/2)
If more than the rated power voltage is applied to the product, replace the product with new one for your safety. Failure to do so might cause fire.
Do not use the product for an application that requires extremely frequent open/close operations. Doing so might cause fire or device failure.
Do not place your hand around the product or bring your face close to the product. The product might rotates due to inappropriate installation, malfunction, or damage, causing injury.
Do not touch the moving parts of the product. Doing so might cause injury.
Do not disassemble the product. Doing so might cause electric shock or device failure.
Dispose of the product as industrial waste in accordance with your local regulations. Do not reuse all or part of this product.
IMPORTANT: After installation, check fully open, shut-off, and spring-return operations of the damper actuator. Check that the damper shaft is held by the shaft clamp without slipping inside the clamp, and that the actuator
is securely attached to the universal bracket when the actuator closes the damper from fully open position to fully closed position or opens the damper from fully closed position to fully open position..
AB-7143
4
Specifications Item Specification
Rated power supply voltage 24 V AC, 50 Hz/60 Hz Operating voltage range 19.2 V AC to 28.8 V AC Power consumption Running 7 W, 7 VA
Holding 3.5 W Angle of rotation Max. 95° (Max. limit is adjustable from 33 % to 100 %.) Running time Motor (0→100 % position) Approx. 75 s
Spring return (100→0 % position) Approx. 25 s Torque Running 20 N⋅m
Holding 20 N⋅m Spring return 20 N⋅m
Environmental conditions
Rated operating conditions
Ambient temperature -20 °C to 50 °C Ambient humidity 95 %RH (non-condensing) Vibration 4.9 m/s2 (10 Hz to 150 Hz)
Transport/ storage conditions
Ambient temperature -20 °C to 60 °C Ambient humidity 95 %RH or less (non-condensing) Vibration 9.8 m/s2 (10 Hz to 150 Hz)
Protection rating IEC IP54 (dust-proof and splash-proof) with the cable conduit facing downward * Do not use the actuator outdoors exposed to rain.
Cable Power 0.75 mm2 x 2 cores, approx. 1 m long Auxiliary switch 0.75 mm2 x 6 cores, approx. 1 m long
Materials Housing Polycarbonate resin Clamp Galvanized steel Universal bracket Galvanized steel plate
Color Housing Gray Weight Approx. 2.4 kg Applicable damper shaft 10 mm to 25.4 mm, 15 mm long or longer
10 mm to 25.4 mm, 15 mm long or longer
Withstand voltage Between case and cable 1 mA or less at 500 V AC for 1 min. Insulation resistance Between case and cable 100 MΩ or higher at 500 V DC Auxiliary switches SPDT x 2 (at 10 % and 10–90 %)
1 mA to 3 (0.5) A, 250 V AC or lower (resistive load: 3A, inductive load: 0.5A)Accessories Universal bracket x 1 (Part No. 12596-00001)
Plastic bag for protection M4 tapping screws x 2 Crank handle for manual operation x 1 Installation instruction sheet (71382-00001.A) x 1
Optional items (Order separately.)
Auxiliary device Transformer (if needed) Attachment Attachment (Model Z-AF) for replacing the former models*
IEC: International Electrotechnical Commission Note: * Mounting dimensions of Model MY6055B2001 differ from the mounting dimensions of Model MY6045 series. This attachment allows to
replace Model MY6045 series with Model MY6055B2001 without changing the mounting position of the universal bracket.
AB-7143
5
Dimensions and Maintenance Clearance
IMPORTANT: Besides the below maintenance clearance, leave enough clearance for a tool, such as a torque wrench, to
tighten the hexagonal nuts of the shaft clamp. Side view
Figure 1. Dimensions and maintenance clearance (mm): Side view
Front view
Figure 2. Dimensions and maintenance clearance (mm): Front view
Universal bracket (Part No. 12596-00001)
Figure 3. Dimensions (mm): Universal bracket
98
80
49
100
(Mai
nten
ance
cl
eara
nce)
100
(Mai
nten
ance
cl
eara
nce)
32 27 162172182236100
(Maintenance clearance)
229
4.4
20
12 5
2
7
2
R2.2R2.2
R2.2
4 4 5 10 1312
12
11.2512.75 12
22
85
59
20
6
200
(Mai
nten
ance
cle
aran
ce)
AB-7143
6
Parts Identifications
Figure 4. Parts identifications
Setting dialfor auxiliary switches
Clamp
Insertion part
Mechanical stopper
Lock switch
Hexagonal hole for crank handle
Housing
AB-7143
7
Installation
CAUTION
Do not send shock to the product. Doing so might damage the product.
Install and use the product in a location that meets the operating conditions (temperature, humidity, power, vibration, shock, mounting direction, atmospheric condition, etc.) as listed in the specifications. Failure to do so might cause fire or device failure.
Take anti-lightning measures based on regional and building characteristics. Lightning might cause fire or critical damage to the product without the anti-lightning measures.
Do not install the product in an environment with high heat radiation. High heat radiation might cause malfunction of the actuator.
Do not use the product in an atmosphere containing corrosive gas. Doing so might damage the actuator or its components.
Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.
IMPORTANT: • Avoid application that keeps the actuator open and close operations excessively frequent. • Meet the actuator rotating direction with the damper rotating direction. • For perfect installation, firmly tighten the screws of the actuator without loose connection. • Leave clearance for maintenance as shown in Figs. 1 and 2. Besides, leave a clearance for a tool (e.g., torque
wrench) to tighten the hexagonal nuts of the clamp. Prior to installation
1) Check the shape and size of the damper shaft. Depending on the shape and size of the shaft, the insertion part of the clamp needs to be removed. See the Removal of the clamp insertion part section.
Figure 5. Clamp types corresponding to shape and size of damper shaft
2) Check the length of the damper shaft. Installation steps differ depending on the length of the damper shaft.
3) Check the rotating direction of the damper shaft and meet the actuator rotating direction with the shaft rotating direction. Actuator mounting orientation differ depending on the damper shaft rotating direction. Spring-return direction of the actuator is indicated with "L" (left) or "R" (right) printed on the actuator front or rear face. "L" face must face the front for the counterclockwise spring-return direction, and "R" face must face the front for the clockwise spring-return direction.
10–22 mm 19–25.4 mm
Clamp with insertion part
Damper shaft Damper shaft
Clamp without insertion part
AB-
InstMouFor couthroFor clocinstcloc
Fig
MouFollcloc
1.
2.
3.
4. 5. 6.
7.
8.
1)
2)
-7143
tallation stepunting on minmounting the
nterclockwiseough 4).
mounting theckwise ("R" ruction Mounckwise to clo
gure 6. Installa
unting on the dow the below
ckwise ("R" dirPull out the from the "R"Pull out the face of the aMeet the mamounting hoFix the clamAttach the pFix the positthe step 1. Unscrew thethe "L" face Attach the position on t
Mount the acPosition the possible, butdamper.
Note: * Check the a
the actuator counterclockfront for the
Temporarily fPosition the adamper shafhexagonal nu
M
D
PDamper blade
ps: nimum of 85 e actuator on
e ("L" direction
e actuator ondirection) to
nting on theose first, then g
tion image for m
damper shaft instructions torection). C-clip and re
" face of the acC-clip and rem
actuator. ark of the clamole, and attach
mp with the C-cosition indicattion indicator
e M4 screw ofand remove thmechanical
the "R" face w
ctuator on the actuator as
t do not allow
actuator spring-rr must face the fkwise to close, adamper shaft ro
fix the actuatoactuator mounft, as shown uts of the clam
Min. 85 mm
Damper blade
Damper shaft
osition indicator
mm long damn the damper ) to close, follo
n the damper close, follo
e damper sgo to the steps
min. 85 mm long
rotating clockwo mount the ac
emove the posctuator. move the clam
mp with the mah the clamp to clip pulled out tor to the "L" fawith the C-clip
f the mechanihe mechanica
stopper to with the M4 scr
damper shaftnear the dam
w the actuato
return direction. front for damperand the "R" faceotating clockwis
or. nting hole line
in Fig. 9 anmp.
Actuatorr
mper shaft shaft rotating
ow the steps 1
shaft rotatingw the below
shaft rotatings 1) through 4)
g damper shaft
wise to closectuator rotating
sition indicato
mp from the "L
ark on the shafthe "R" face.at the step 2.ace. p pulled out a
cal stopper onal stopper.
the full-openrew.
. mper blade asr to touch the
The "L" face or shaft rotating e must face the se to close.
parallel to thend tighten the
r
Clamp
Damper s
8
g )
g w g ).
g
or
L"
ft
at
n
n
s e
of
e e
Figu
Figu
shaft
ure 7. Temporar(coun
ure 8. Temporar(c
Figure 9. G m
Good mou
(Mounting hto the damp
Damperblade
Unive
Rotof damper
Circled marksMeet the markthe mark of thmounting hole
Uni
Rof damp
Circled marksMeet the mathe mark of tmounting hol
ry installation fonterclockwise ro
ry installation foclockwise rotatio
Good and bad mmin. 85 mm long
DashedMountininside th
unting
hole line is paralper shaft.)
Ac
ersal bracket
tating directionr shaft to close
: k of the clamp withe actuator
e.
versal bracket
Rotating directionper shaft to close
s: rk of the clamp withe actuator e.
or min. 85 mm lootation for closin
or min. 85 mm loon for closing)
mounting orientag damper shaft
d lines: ng hole line he actuator
llel
Bad
(Mountingparallel to
Damper shaft
ctuator
h
Dire
th
ong damper shafng)
ong damper shaf
ation for
mounting
g hole line is NOo the damper sh
Clam
C-clip
Direction of spring return
ClampC
ection of spring reMechanstopper
ft
ft
OT haft.)
mp
pC-clip
eturnical
AB-7143
9
3) Attach the universal bracket (accessory) to the duct. Position the universal bracket so that its mounting screws do not touch the damper blade.
<Precautions for mounting the universal bracket> Follow the below instructions for bending the universal bracket at the specified positions to mount.
a. Position the actuator on the damper shaft as near the damper blade as possible in order to bend the universal bracket as little as possible.
b. Bend the universal bracket at the specified positions (once for each position). Note that the bending angle must be 45° or less. See the figure below.
Figure 10. Bending the universal bracket 4) Fix the actuator with the universal bracket on the duct.
Insert the pin of the universal bracket into the notch of the actuator to fix the actuator on the duct. Note: * The universal bracket prevents the actuator from rolling. * The actuator will slightly pitch when actuating the damper
shaft.
Figure 11. Fixing the actuator with the universal bracket
Jump to the Installation steps: Common to any length of the damper shaft section.
Installation steps: Mounting on 15–85 mm long damper shaft Installation steps differ depending on the damper shaft rotating direction. See 3) of Prior to installation section, and go to the corresponding installation steps.
Figure 12. Installation image for 15–85 mm long damper shaft Mounting on the damper shaft rotating counterclockwise ("L" direction) to close
1) Pull out the C-clip and remove the clamp from the "L" face of the actuator.
2) Attach the clamp to the damper shaft as near the damper blade as possible. (Make sure that the clamp does not touch the damper.)
3) Temporarily fix the clamp on the damper shaft. Set the clamp mounting orientation so that the mounting hole line of the actuator to be mounted at the steps 7) and 8) is parallel to the damper shaft, and tighten the hexagonal nuts of the clamp.
4) Pull out the C-clip and remove the position indicator from the "R" face of the actuator.
5) Meet the mark of the position indicator with the mark on the shaft mounting hole, and attach the position indicator to the "L" face of the actuator.
6) Fix the position indicator with the C-clip pulled out at the step 4).
7) Mount the actuator on the damper shaft so that the "L" face of the actuator faces the front.
Insert the pin..
Universalbracket
15–85 mm
Damper blade
Actuator
ClampPosition indicator
Damper blade
Damper shaft
45°
a. Position the actuator onthe damper shaft near thedamper blade.
b. Bend the universal bracketat these positions.
AB-
8)
Figu
9)
10)
(t
CMina
-7143
Fix the clampC-clip pulled
ure 13. Tempora(coun
Figure 14. 1
Attach the unPosition the screws do no
Note: * To bend the
the followingMounting on3) <Precaut
Fix the actuatInsert the pinthe actuator toNote: * The universa* The actuato
shaft.
Jump to thelength of the
Good mount
(Mounting hole lto the damper s
Damperblade
Universal br
ircled marks: Meet the mark of tndicator with the mctuator mounting
p on the "R" fout at the ste
ary installation fnterclockwise ro
Good and bad
15–85 mm long
niversal brackeuniversal bra
ot touch the da
universal brackg: n the damper shtions for moun
tor with the un of the universo fix the actua
al bracket prever will slightly pitc
e Installatione damper sha
Dashed linesMounting hoinside the ac
ting
ine is parallelhaft.)
Dampershaft
Actuato
C-clip
racket
Rotating directioof damper shaft t
the positionmark of thehole.
face of the acp 1).
for 15–85 mm lootation for closin
mounting orientdamper shaft
et (accessory)acket so thatamper blade.
ket for mounting
haft rotating clonting the univer
niversal brackesal bracket int
ator on the duc
ents the actuatoch when actuat
steps: Comaft section.
s: ole line ctuator
Bad mou
(Mounting holeparallel to the d
r
r
Direct
Clamp
n to close
tuator with the
ong damper shafng)
tation for
) to the duct.t its mounting
on the duct, see
ockwise to closersal bracket>
et on the duct.to the notch o
ct. See Fig. 11
or from rolling.ing the damper
mmon to any
unting
e line is NOT damper shaft.)
tion of spring retu
Position indica
C-clip
10
e
ft
g
e
e
. of .
y
Moudire
1)
2)
3)
4)
5)
6)
7) F
Figu
8)
9)
rn
ator
of d
unting on theection) to clo
Pull out the Cface of the ac
Attach the cdamper bladdoes not touc
Temporarily fSet the clamounting holsteps 6) andtighten the he
Unscrew thethe "L" face a
Attach the meon the "R" fa
Mount the acface of the ac
Fix the clamp C-clip pulledactuator mou
ure 15. Tempora(c
Attach the unPosition the screws do no
Note: * To bend the
the followingMounting on3) <Precaut
Fix the actuatInsert the pinthe actuator toNote: * The universa* The actuato
shaft.
Jump to thelength of the
U
P
Rotating dirdamper shaft for s
Circled marks: Meet the mark ofindicator with theactuator mountin
e damper shase
C-clip and remctuator.
clamp to the e as possiblech the damper
fix the clamp oamp mountinge line of the ac
d 7) is paralleexagonal nuts
M4 screw of and remove th
echanical stopce with the M4
ctuator on the dctuator faces t
on the "R" faout at the st
unting orientat
ary installation foclockwise rotatio
niversal brackeuniversal bra
ot touch the da
universal brackg: n the damper shtions for moun
tor with the unof the univers
o fix the actua
al bracket prever will slightly pitc
e Installation e damper sha
niversal bracke
Position indicato
ectionshutoff
f the position e mark of the g hole.
aft rotating c
move the clam
damper shaf. (Make sure r.)
on the dampeg orientation ctuator to be m
el to the dams of the clamp.
f the mechaniche mechanical
pper to the ful4 screw.
damper shaft the front
ace of the acttep 1). See Ftion.
for 15–85 mm loon for closing)
et (accessory)acket so thatamper blade.
ket for mounting
haft rotating clonting the univer
niversal brackesal bracket int
ator on the duc
ents the actuatoch when actuat
steps: Comaft section.
et
or
C-clip
ClamDirespri
lockwise ("R
mp from the "L
ft as near thethat the clamp
r shaft. so that the
mounted at theper shaft, and.
cal stopper onl stopper.
l-open position
so that the "R
tuator with theFig. 14 for the
ong damper shaf
) to the duct.t its mounting
on the duct, see
ockwise to closersal bracket>
et on the ductto the notch o
ct. See Fig. 11
or from rolling.ing the damper
mmon to any
C-clip
p ection of ng return
Mechanicstopper
"
L"
e p
e e d
n
n
R"
e e
ft
g
e
e
. of .
y
cal
I
I
Installation sCommon to arotation. The following 85 mm long clockwise anbefore-mentiocomplete the
1) Check thposition. 10 mm wactuator otorque is
IMPORTANTTighten th10 N·m toSmaller thconnectiothe actuaopen or ctorque minuts/clam
Figu
IMPORTANT After inst
spring-ret Check th
clamp witthe actuabracket.
WN
steps: any length of
installation steand 15–85 md countercloc
oned steps, installation.
hat the dampThen, tighten
width across on the dampe10 N·m.
T: he hexagonaorque. han the 10 Non of the clamator thereforclose the damight wear out
mp.
ure 16. Tighteni
T: tallation, cheturn operatioat the dampthout slippin
ator is secure
Width across flatut tightening tor
f the damper
eps are commmm long dampckwise. Afte
follow the
er shaft is inn the hexagonaflats) to compr shaft. Note
al nuts of the
N·m torque mmp on the dare may not mper. Largert the thread o
ing the nuts of t
eck fully opeons of the actper shaft is hg inside the ely attached
s of the nuts: 10rque: 10 N·m
shaft for eac
mon to the bothper shafts rotaer completing
below steps
n the fully cloal nuts (with pletely mountthat nut tighte
clamp with
might cause loamper shaft, be able to
r than the 10 of the hexag
he clamp
en, shut-off, tuator.
held by the sclamp, andto the unive
11
0 mm
ch
h min. ating the s to
osed
t the ening
oose and fully N·monal
and
shaft that
ersal
Removal of c
1) Pull out tactuator.
2) Remove tNote: * Be sure
The cap
Fig
3) Pull out th
4) Remove t
Fi
5) Press theposition.
Figure 2
6) Attach thethe clamp
Fig
7) Meet themounting
8) Fix the cla
Clamp
Pul
Clamp
Re
Press.
Clamp
Clamp
R
clamp insertio
the C-clip and
he black resin
to keep the remp will be attached
gure 17. Remov
he insertion pa
Figure 18. Pulli
the insertion p
gure 19. Remoe holder for
0. Pressing the
e black resin cp.
gure 21. Attache mark of the
holder and at
amp with the C
Insertion parl out.
Insertion part emove.
Holderinsertion p
Holder for insertion part
Clamp
Black resin caRemove.
on part
d remove the
n cap attached
moved cap. d to the clamp a
ving the black re art.
ing the insertion part from the h
oving the insertithe insertion
e holder for the cap (removed
hing the black ree clamp with ttach the clam
C-clip pulled o
rt
Clamp
Clamp r forpart
Clamp
Black re
ap
Clamp
AB-7
e clamp from
d to the clamp
again.
esin cap
n part
holder.
on part part back in
insertion part
d at the step 2
esin cap the mark of
mp to the actua
out at the step
p
Insertion par
Insertion part
Holder for insertion part
esin cap
Black resin cap
7143
m the
.
the
2)) to
f the ator.
p 1).
rt
t
p
AB-7143
12
Wiring
WARNING
Before wiring and maintenance, be sure to turn off the power to the product. Failure to do so might cause electric shock.
CAUTION
Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.
All wiring must comply with applicable codes and ordinances.
Provide a circuit breaker for the power to the product.
Provide a circuit protector (e.g., a fuse, cut-off device) for the control panel to ensure your safety.
Wiring diagrams
Wiring numbers are indicated on the lead wire insulating jackets.
Note: *1 S1-S2 contact is ON at 10 % or smaller position. *2 Position for S4-S5 contact is adjustable within 10 % to 90 %
range. S4-S5 contact is ON at the set position or smaller than the set position.
Figure 22. Wiring diagram
Setting (Angle of Rotation)
WARNING
Before wiring and maintenance, be sure to turn off the power to the product. Failure to do so might cause electric shock.
Do not disassemble the spring unit of the product. The spring unit might rapidly rotate or jump out of the actuator, resulting in serious injury.
CAUTION
If more than the rated power voltage is applied to the product, replace the product with new one for your safety. Failure to do so might cause fire.
Do not place your hand around the product or bring your face close to the product. The product might rotates due to inappropriate installation, malfunction, or damage, causing injury.
Do not touch the moving parts of the product. Doing so might cause injury.
IMPORTANT: After changing the mechanical stopper position,
make sure that the damper shaft is stopped at the changed mechanical stopper position.
Check that the set screws of the mechanical stopper are not loose.
Setting the maximum position
To set the maximum angle to 95° or smaller, change the mechanical stopper position within 33–100 % range. Mechanical stopper changed to the desired position must be fixed with the M4 screw.
Figure 23. Setting the angle of rotation
1 2
M
N L24 V AC
10 % 10–90 % adjustable
*1 *2
Maximum position:Adjustable from 33 % to 100 %
Mechanical stopper
AB-7143
13
Manual Override
WARNING
Before wiring and maintenance, be sure to turn off the power to the product. Failure to do so might cause electric shock.
CAUTION
Do not place your hand around the product or bring your face close to the product. The product might rotates due to inappropriate installation, malfunction, or damage, causing injury.
Do not touch the moving parts of the product. Doing so might cause injury.
To lock the damper at the desired position, use the crank handle (accessory).
1) Insert the crank handle into the hexagonal hole provided on the "L" or "R" face of the actuator, and rotate the crank handle to the direction the arrow (printed above the hexagonal hole) indicates.
Figure 24. Manually opening the damper
2) When the damper blade reaches the desired position, lock the actuator with the lock switch and remove the crank handle.
IMPORTANT: After using the crank handle, attach the crank
handle as "A" in the below figure shows. Completely attach the crank handle to the hexagonal hole so that it does not come off.
Figure 25. Locking the damper position
Auxiliary Switch Setting The actuator is equipped with two SPDT switches (fixed at 10 % position and adjustable from 10 to 90 % position). To set the adjustable switch, attach the crank handle to the auxiliary switch setting dial and rotate the dial to the setting position. After setting the dial, make sure that the auxiliary switch operates at the set position.
Figure 26. Setting the auxiliary switch
Crank handle
Rotating direction of crank handle
Crank handle
Auxiliary switch setting dial
Lock switch
Lock.
A Crank handle
Attach.
Rotate.
AB-7143
14
Blank page added for editing purpose.
AB-7143
15
Blank page added for editing purpose.
AB-7143
Specifications are subject to change without notice.
Building Systems Company http://www.azbil.com/ Rev. 0.0 Jun. 2014 AB-7143(J: AI-7143 Rev. 1.0)
16