distance warning system
TRANSCRIPT
KEEP DISTANCE WARNING SYSTEM
CHAPTER 1
INTRODUCTION
1.1 INTRODUCTION:
Most of the accidents in high-ways are happening due to the drowsiness
of drivers, most often this symptom is found in long distance truck drivers, these
drivers may take some time to recognize the opposite vehicle, which is running at low
speed, resulting accident. This kind of accidents may happen due to the drunken
drivers also. So to increase safety an electronic warning system is essential to alert the
drivers. This kind of system can be installed in all types of vehicles, especially in
commercial vehicles, so that accident rate can be minimized. The warning system
designed here can be called as driver attention system, which raises an alarm and
energizes the display board automatically when the following vehicle came near to the
in-front running vehicle.
The system is designed with 89S52 microcontroller, the task is quite
simple, the following vehicle detection circuit is designed with infrared sensors, when
the IR signal is interrupted due to the following vehicle, the circuit generates high
signal and it is fed to microcontroller. It offers several advantages over conventional
multi-chip systems. There is a cost and space advantage as extra chip costs and
printed circuit board and connectors required to support multi-chip systems are
eliminated.
SOFTWARE REQUIREMENT:
1. KEIL MICRO VISION-3
2. MICRO FLASH
HARDWARE REQUIREMENT:
1. MICROCONTROLLER (89S52)
2. LM324.
3. ULTRASONIC SENSOR
4. LCD DISPLAY
SRTIST, NALGONDA 1
KEEP DISTANCE WARNING SYSTEM
1.2 AIM:
The aim of this system is to alert the following vehicle whenever it
came very close to the ahead vehicle; thereby to some extent accidents can be
avoided .Many accidents at High-ways are taking place due to the close running of
vehicles, all of sudden, if the in front vehicle driver reduces the speed or applied
breaks, then it is quite difficult to the following vehicle driver to control his vehicle,
resulting accidents avoid this kind of accident, the warning system, which contains
alarm and display system can arrange at rear side of each and every vehicle.
1.3 BLOCK DIAGRAM:
FIG (1.3) BLOCK DIAGRAM
SRTIST, NALGONDA 2
AT 89S52MICRO -CONTROLLER
LCD DISPLAY
POWER SUPPLY
ULTRASONIC SENSOR
BUZZER
KEEP DISTANCE WARNING SYSTEM
1.4 FLOW CHART:
FIG (1.4) FLOWCHART
1.5 CONCLUSION:
Hence, the circuit is designed such that whenever the infrared signal is
interrupted, logic high signal is generated and it is fed to microcontroller, on receipt of
this signal, the controller activates the display board and alarm automatically.
SRTIST, NALGONDA 3
Object detection is displayed on LCD
START
Initialization of Microcontroller
Initialization of LCD
Initialization of ultrasonic
STOP STOP
If object is
detected
yes
NO
Buzzer on
KEEP DISTANCE WARNING SYSTEM
CHAPTER 2
DESCRIPTION OF MICROCONTROLLER
2.1 INTRODUCTION :
The 8051 is an original member of the 8051 family. There are two other
members in the 8051 family of microcontrollers. They are 8052 and 8031. All the
three microcontrollers will have the same internal architecture, but they differ in the
following aspects.
8031 has 128 bytes of RAM, two timers and 6 interrupts.
89S51 has 4KB ROM, 128 bytes of RAM, two timers and 6
interrupts.
89S52 has 8KB ROM, 128 bytes of RAM, three timers and
8 interrupts.
Of the three microcontrollers, 89S51 is the most preferable. Microcontroller
supports both serial and parallel communication.
In the concerned project 89S52 microcontroller is used. Here microcontroller
used is AT89S52, which is manufactured by ATMEL laboratories.
The AT89S52 provides the following standard features: 8Kbytes of Flash,
256 bytes of RAM, 32 I/O lines, three 16-bit timer/counters, six-vector two-level
interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry.
In addition, the AT89S52 is designed with static logic for operation down to zero
frequency and supports two software selectable power saving modes. The Idle Mode
stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt
system to continue functioning. The Power down Mode saves the RAM contents but
freezes the oscillator, disabling all other chip functions until the next hardware reset.
The Idle Mode stops the CPU while allowing the RAM, timer/counters,
serial port and interrupt system to continue functioning. The Power down Mode
saves the RAM contents but freezes the oscillator disabling all other chip functions
until the next hardware reset.
By combining a versatile 8-bit CPU with Flash on a monolithic chip, the
AT89C52 is a powerful microcomputer which provides a highly flexible and cost
effective solution to many embedded control applications.
SRTIST, NALGONDA 4
KEEP DISTANCE WARNING SYSTEM
2.2 PIN CONFIGURATION:
FIG (2.2) PIN DIAGRAM OF 89S52 IC
SRTIST, NALGONDA 5
KEEP DISTANCE WARNING SYSTEM
2.3 PIN DESCRIPTION:
VCC
Pin 40 provides Supply voltage to the chip. The voltage source is +5v
GND.
Pin 20 is the grounded
Port 0
Port 0 is an 8-bit open drain bidirectional I/O port from pin 32 to 39. As an
output port each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the
pins can be used as high-impedance inputs In this mode P0 has internal pull-ups.
Port 0 also receives the code bytes during Flash programming, and outputs the
code bytes during program verification. External pull-ups are required during program
verification.
Port 1
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups from pin 1 to 8.
The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to
Port 1 pins they are pulled high by the internal pull-ups and can be used as inputs. As
inputs, Port 1 pins that are externally being pulled low will source current (IIL)
because of the internal pull-ups.
In addition, P1.0 and P1.1 can be configured to be the timer/counter 2 external
count input (P1.0/T2) and the timer/counter 2 trigger input (P1.1/T2EX), respectively,
as shown in following table.
Port 1 also receives the low-order address bytes during Flash programming
and program verification.
SRTIST, NALGONDA 6
KEEP DISTANCE WARNING SYSTEM
TABLE (2.3.1) PORT 1 FUNCTIONS
Port 2
Port 2 is an 8-bit bidirectional I/O port with internal pull-ups from pin 21 to
28. The Port 2 output buffers can sink / source four TTL inputs. When 1s are written
to Port 2 pins they are pulled high by the internal pull-ups and can be used as inputs.
As inputs, Port 2 pins that are externally being pulled low will source current (IIL)
because of the internal pull-ups.
Port 2 emits the high-order address byte during fetches from external program
memory and during accesses to external data memory that uses 16-bit addresses
(MOVX @ DPTR). In this application it uses strong internal pull-ups when emitting
1s. During accesses to external data memory that uses 8-bit addresses (MOVX @ RI),
Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the
high-order address bits and some control signals during Flash programming and
verification.
Port 3
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups from pin 10 to
17. The Port 3 output buffers can sink / source four TTL inputs. When 1s are written
to Port 3 pins they are pulled high by the internal pull-ups and can be used as inputs.
As inputs, Port 3 pins that are externally being pulled low will source current (IIL)
because of the pull-ups.
TABLE (2.3.2) PORT 3 FUNCTIONS
SRTIST, NALGONDA 7
KEEP DISTANCE WARNING SYSTEM
RST
Pin 9 is the Reset input. It is active high. Upon applying a high pulse to this
pin, the microcontroller will reset and terminate all activities. A high on this pin for
two machine cycles while the oscillator is running resets the device.
ALE/PROG
Address Latch is an output pin and is active high. Address Latch Enable
output pulse for latching the low byte of the address during accesses to external
memory. This pin is also the program pulse input (PROG) during Flash programming.
In normal operation ALE is emitted at a constant rate of 1/6 the oscillator frequency,
and may be used for external timing or clocking purposes.
Note, however, that one ALE pulse is skipped during each access to external
Data Memory. If desired, ALE operation can be disabled by setting bit 0 of SFR
location 8EH. With the bit set, ALE is active only during a MOVX or MOVC
instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has
no effect if the microcontroller is in external execution mode.
PSEN
Program Store Enable is the read strobe to external program memory. When
the AT89C52 is executing code from external program memory, PSEN is activated
twice each machine cycle, except that two PSEN activations are skipped during each
access to external data memory.
EA/VPP
External Access Enable EA must be strapped to GND in order to enable the
device to fetch code from external program memory locations starting at 0000H up to
FFFFH. Note, however, that if lock bit 1 is programmed, EA will be internally latched
on reset. EA should be strapped to VCC for internal program executions. This pin also
receives the 12-volt programming enable voltage (VPP) during Flash programming
when 12-volt programming is selected.
SRTIST, NALGONDA 8
KEEP DISTANCE WARNING SYSTEM
XTAL1
Input to the inverting oscillator amplifier and input to the internal clock
operating circuit.
XTAL2
Output from the inverting oscillator amplifier.
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respectively, of an inverting
amplifier which can be configured for use as an on chip oscillator, as shown in Figure
5.3. Either a quartz crystal or ceramic resonator may be used. To drive the device
from an external clock source, XTAL2 should be left unconnected while XTAL1 is
driven .
FIGURE (2.3.1) CRYSTAL CONNECTIONS
SRTIST, NALGONDA 9
KEEP DISTANCE WARNING SYSTEM
FIGURE( 2.3.2) EXTERNAL CLOCK DRIVE CONFIGURATIONThere are no requirements on the duty cycle of the external clock signal, since the
input to the internal clocking circuitry is through a divide-by two flip-flop, but
minimum and maximum voltage high and low time specifications must be observed.
IDLE MODE
In idle mode, the CPU puts itself to sleep while all the on-chip peripherals
remain active. The mode is invoked by software. The content of the on-chip RAM and
all the special functions registers remain unchanged during this mode. The idle mode
can be terminated by any enabled interrupt or by a hardware reset. It should be noted
that when idle is terminated by a hardware reset, the device normally resumes
program execution, from where it left off, up to two machine cycles before the
internal reset algorithm takes control.
On-chip hardware inhibits access to internal RAM in this event, but access to
the port pins is not inhibited. To eliminate the possibility of an unexpected write to a
port pin when Idle is terminated by reset, the instruction following the one that
invokes Idle should not be one that writes to a port pin or to external memory.
POWER DOWN MODE
In the power down mode the oscillator is stopped, and the instruction that
invokes power down is the last instruction executed. The on-chip RAM and Special
Function Registers retain their values until the power down mode is terminated. The
only exit from power down is a hardware reset. Reset redefines the SFRs but does not
change the on-chip RAM. The reset should not be activated before VCC is restored to
its normal operating level and must be held active long enough to allow the oscillator
to restart and stabilize.
Table (2.3.3) Status of External Pins During Idle and Power Down Mode
SRTIST, NALGONDA 10
KEEP DISTANCE WARNING SYSTEM
2.4 TIMERS:
Timer 0 and 1
Timer 0 and Timer 1 in the AT89S52 operate the same way as Timer 0 and
Timer 1 in the AT89S52. Register pairs (TH0, TL1), (TH1, TL1) are the 16-bit
counter registers for timer/counters 0 and 1.
Timer 2
Timer 2 is a 16-bit Timer/Counter that can operate as either a timer or an event
counter. The type of operation is selected by bit C/T2 in the SFR T2CON. Timer 2
has three operating modes: capture, auto-reload (up or down counting), and baud rate
generator. The modes are selected by bits in T2CON, as shown in Table 5.2. Timer 2
consists of two 8-bit registers, TH2 and TL2. In the Timer function, the TL2 register
is incremented every machine cycle. Since a machine cycle consists of 12 oscillator
periods, the count rate is 1/12 of the oscillator frequency.
Table (2.4) Timer 2 Operating Modes
In the Counter function, the register is incremented in response to a 1-to-0
transition at its corresponding external input pin, T2. In this function, the external
input is sampled during S5P2 of every machine cycle. When the samples show a high
in one cycle and a low in the next cycle, the count is incremented. The new count
value appears in the register during S3P1 of the cycle following the one in which the
transition was detected. Since two machine cycles (24 oscillator periods) are required
to recognize a 1-to-0 transition, the maximum count rate is 1/24 of the oscillator
frequency. To ensure that a given level is sampled at least once before it changes, the
level should be held for at least one full machine cycle.
SRTIST, NALGONDA 11
KEEP DISTANCE WARNING SYSTEM
There are no restrictions on the duty cycle of external input signal, but it
should for at least one full machine to ensure that a given level is sampled at least
once before it changes.
2.5 INTERRUPTS:
The AT89S52 has a total of six interrupt vectors: two external interrupts
(INT0 and INT1), three timer interrupts (Timers 0, 1, and 2), and the serial port
interrupt. These interrupts are all shown in Figure 2.5
FIGURE (2.5) INTERRUPTS SOURCE
Each of these interrupt sources can be individually enabled or disabled by
setting or clearing a bit in Special Function Register IE. IE also contains a global
disable bit, EA, which disables all interrupts at once.
Timer 2 interrupt is generated by the logical OR of bits TF2 and EXF2 in
register T2CON. Neither of these flags is cleared by hardware when the service
routine is vectored to. In fact, the service routine may have to determine whether it
was TF2 or EXF2 that generated the interrupt, and that bit will have to be cleared in
software.
The Timer 0 and Timer 1 flags, TF0 and TF1, are set at S5P2 of the cycle in
which the timers overflow.
SRTIST, NALGONDA 12
KEEP DISTANCE WARNING SYSTEM
Table (2.5) Interrupts Enable Register
2.6 MEMORY ORGANIZATION :
The total memory of 89S52 system is logically divided in Program memory
and Data memory. Program memory stores the programs to be executed, while data
memory stores the data like intermediate results, variables and constants required for
the execution of the program. Program memory is invariably implemented using
EPROM, because it stores only program code which is to be executed and thus it need
not be written into. However, the data memory may be read from or written to and
thus it is implemented using RAM.
Further, the program memory and data memory both may be categorized as
on-chip (internal) and external memory, depending upon whether the memory
physically exists on the chip or it is externally interfaced. The 89S52 can address
8Kbytes on-chip memory whose map starts from 0000H and ends at 1FFFH. It can
address 64Kbytes of external program memory under the control of PSEN (low)
signal.
SRTIST, NALGONDA 13
KEEP DISTANCE WARNING SYSTEM
CHAPTER-3
POWER SUPPLY
3.1 INTRODUCTION:
Power supplies are designed to convert high voltage AC mains electricity to a
suitable low voltage supply for electronics circuits and other devices.
Fig (3.1) Block Diagram of a Regulated Power Supply System
3.2 TRANSFORMER:
A transformer steps down high voltage AC mains to low voltage AC. Here we
are using a center-tap transformer whose output will be sinusoidal with 24V peak to
peak.
.
Fig( 3.2) Output Waveform of transformer
The low voltage AC output is suitable for lamps, heaters and special AC motors. It is
not suitable for electronic circuits unless they include a rectifier and a smoothing
capacitor. The transformer output is given to the rectifier circuit.
3.3 RECTIFIER:
A rectifier converts AC to DC, but the DC output is varying. There are several
types of rectifiers; here we use a bridge rectifier.
SRTIST, NALGONDA 14
KEEP DISTANCE WARNING SYSTEM
The Bridge rectifier is a circuit, which converts an ac voltage to dc voltage
using both half cycles of the input ac voltage. The circuit has four diodes connected
to form a bridge. The ac input voltage is applied to the diagonally opposite ends of the
bridge. The load resistance is connected between the other two ends of the bridge.For
the positive half cycle of the input ac voltage, diodes D1 and D3 conduct. The
conducting diodes will be in series with the load resistance RL and hence the load
current flows through RL. For the negative half cycle of the input ac voltage, diodes
D2 and D4 conduct.The conducting diodes D2 and D4 will be in series with the load
resistance RL and hence the current flows through RL in the same direction as in the
previous half cycle. Thus a bi-directional wave is converted into unidirectional.
FIG (3.3.1) Rectifier circuit
FIG (3.3.2) Rectifier output
Smoothing:
The smoothing block smoothes the DC from varying greatly to a small ripple
and the ripple voltage is defined as the deviation of the load voltage from its DC
value. Smoothing is also named as filtering. Filtering is frequently effected by
shunting the load with a capacitor. The action of this system depends on the fact that
SRTIST, NALGONDA 15
KEEP DISTANCE WARNING SYSTEM
the capacitor stores energy during the conduction period and delivers this energy to
the loads during the no conducting period. In this way, the time during which the
current passes through the load is prolonging Ted, and the ripple is considerably
decreased. The action of the capacitor is shown with the help of waveform.
Figure (3.3.3) Smoothing action of capacitor
Figure (3.3.4) Waveform of the rectified output smoothing
3.4 Voltage Regulator:
Voltage Regulator eliminates ripple by setting DC output to a fixed voltage.
Voltage regulator ICs are available with fixed (typically 5V, 12V and 15V) or
variable output voltages.Many of the fixed voltage regulator ICs has 3 leads (input,
output and high impedance). Zener diode is an example of fixed regulator which is
shown here.
SRTIST, NALGONDA 16
KEEP DISTANCE WARNING SYSTEM
Figure (3.4) Voltage Regulator
3.5 POWER SUPPLY CIRCUIT:
Fig (3.5) POWER SUPPLY CIRCUIT
3.5 CONCLUSION:
We here by conclude that most of the digital logic circuits and processors need
a 5 volt power supply. To use these parts we include a regulated 5 volt source.
Unregulated power supply will be ranging from 9 volts to 24 volts DC . So,to make a
5 volt power supply, we use a LM7805 voltage regulator IC .
CHAPTER 4
ULTRASONIC SENSOR
SRTIST, NALGONDA 17
KEEP DISTANCE WARNING SYSTEM
4.1 INTRODUCTION :
Parallax's PING)))™ ultrasonic sensor provides a very low-cost and easy
method of distance measurement. This sensor is perfect for any number of
applications that require you to perform measurements between moving or stationary
objects. Naturally, robotics applications are very popular but you'll also find this
product to be useful in security systems or as an infrared replacement if so desired.
FIG (4.1) ULTRASONIC SENSOR
This measures distance using sonar; an ultrasonic (well above human hearing) pulse is
transmitted from the unit and distance-to-target is determined by measuring the time
required for the echo return. Output from the PING))) sensor is a variable-width pulse
that corresponds to the distance to the target.
PING)))™ Sensor Features:
The PING))) has only has 3 connections, which include Vdd, Vss, and 1 I/O
pin.
The 3-pin header makes it easy to connect using a servo extension cable, no
soldering required.
Several sample codes are available using the Ping))) sensor.
List of technical specifications:
Range - 2cm to 3m (~.75" to 10')
Supply Voltage: 5V +/-10% (Absolute: Minimum 4.5V, Maximum 6V)
Supply Current: 30 mA typ; 35 mA max
3-pin interface (power, ground, signal)
20 mA power consumption
Narrow acceptance angle
Simple pulse in / pulse out communication
Indicator LED shows measurement in progress
Input Trigger - positive TTL pulse, 2 µs min, 5 µs typ.
SRTIST, NALGONDA 18
KEEP DISTANCE WARNING SYSTEM
Echo Pulse - positive TTL pulse, 115 µs to 18.5 ms
Echo Hold-off - 750 µs from fall of Trigger pulse
Burst Frequency - 40 kHz for 200 µs
Size - 22 mm H x 46 mm W x 16 mm D (0.85 in x 1.8 in x 0.6 in)
Ultrasonic sensors (also known as transducers when they both send and receive)
work on a principle similar to radar or sonar which evaluate attributes of a target by
interpreting the echoes from radio or sound waves respectively. Ultrasonic sensors
generate high frequency sound waves and evaluate the echo which is received back by
the sensor. Sensors calculate the time interval between sending the signal and
receiving the echo to determine the distance to an object.
This technology can be used for measuring: wind speed and direction
(anemometer), fullness of a tank, and speed through air or water. For measuring speed
or direction a device uses multiple detectors and calculates the speed from the relative
distances to particulates in the air or water. To measure the amount of liquid in a tank,
the sensor measures the distance to the surface of the fluid. Further applications
include: humidifiers, sonar, medical ultrasonography, burglar alarms, and non-
destructive testing. Systems typically use a transducer which generates sound waves
in the ultrasonic range, above 20,000 hertz, by turning electrical energy into sound,
then upon receiving the echo turn the sound waves into electrical energy which can be
measured and displayed. The technology is limited by the shapes of surfaces and the
density or consistency of the material. For example foam on the surface of a fluid in a
tank could distort a reading.
SRTIST, NALGONDA 19
KEEP DISTANCE WARNING SYSTEM
Transducers:
An ultrasonic transducer is a device that converts energy into ultrasound, or
sound waves above the normal range of human hearing. While technically a dog
whistle is an ultrasonic transducer that converts mechanical energy in the form of air
pressure into ultrasonic sound waves, the term is more apt to be used to refer to
piezoelectric transducers that convert electrical energy into sound. Piezoelectric
crystals have the property of changing size when a voltage is applied, thus applying
an alternating current (AC) across them causes them to oscillate at very high
frequencies, thus producing very high frequency sound waves.
Detectors
Since piezoelectric crystal generate a voltage when force is applied to them, the same
crystal can be used as an ultrasonic detector. Some systems use separate transmitter
and receiver components while others combine both in a single piezoelectric
transceiver.
Alternative methods for creating and detecting ultrasound include magnetostriction
and capacitive actuation.
4.2 Applications of Ultrasonic sensors:
Use in medicine:
Medical ultrasonic transducers (probes) come in a variety of different shapes
and sizes for use in making pictures of different parts of the body. The transducer may
be passed over the surface of the body or inserted into an body opening such as the
rectum or vagina. Clinicians who perform ultrasound-guided procedures often use a
probe positioning system to hold the ultrasonic transducer.
Use in industry;
Ultrasonic sensors are used to detect the presence of targets and to measure the
distance to targets in many automated factories and process plants. Sensors with an on
or off digital output are available for detecting the presence of objects, and sensors
SRTIST, NALGONDA 20
KEEP DISTANCE WARNING SYSTEM
with an analog output which varies proportionally to the sensor to target separation
distance are commercially available.
Ultrasonic sensors are commonly used for a wide variety of noncontact presence,
proximity, or distance measuring applications. These devices typically transmit a
short burst of ultrasonic sound toward a target, which reflects the sound back to the
sensor. The system then measures the time for the echo to return to the sensor and
computes the distance to the target using the speed of sound in the medium.
Wavelength of Sound as a Function of Sound Speed and Frequency:
The wavelength of sound changes as a function of both the speed of sound and
the frequency, as shown by the expression:
λ = c/f
where:
λ = wavelength
C= speed of light
F = frequency
Figure 2 is a plot of the wavelength of sound as a function of frequency at room
temperature in air.
FIG (4.2) PLOT OF WAVE LENGTH VS FREQUENCY
SRTIST, NALGONDA 21
KEEP DISTANCE WARNING SYSTEM
BackgroundNoise
The level of background ultrasonic noise diminishes as the frequency increases. The reason is
that less noise at the higher frequencies is produced in the environment, and the noise that is produced
is greatly attenuated as it travels through the air.
4.3 Ultrasonic sensor drive circuit:
The inverter is used for the drive of the ultrasonic sensor. The two inverters
are connected in parallel because of the transmission electric power increase.
The phase with the voltage to apply to the positive terminal and the negative terminal of the
sensor has been 180 degrees shifted. Because it is cutting the direct current with the
capacitor, about twice of Voltage of the inverter output are applied to the sensor.
Signalamplificationcircuit:
Generally, the positive and the negative power supply are used for the operational amplifier.
The circuit this time works with the single power supply of +9 V. Therefore, for the positive
input of the operational amplifiers, the half of the power supply voltage is appied as the bias
voltage and it is made 4.5 V in the central voltage of the amplified alternating current signal.
When using the operational amplifier with the negative feedback, the voltage of the positive
input terminal and the voltage of the negative input terminal become equal approximately.
So, by this bias voltage, the side of the positive and the side of the negative of the alternating
current signal can be equally amplified. When not using this bias voltage, the distortion
causes the alternating current signal.
Signal detector:
This circuit is the circuit which detects the ultrasonic which returned from the
measurement object. The output of the detection circuit is detected using the comparator. At
the circuit this time, the operational amplifier of the single power supply is used instead of
the comparator. The operational amplifier amplifies and outputs the difference between the
positive.
In case of the operational amplifier which doesn't have the negative feedback, at a
little input voltage, the output becomes the saturation state. So, when the positive input
becomes higher a little than the negative input, the difference is tens of thousands of times
amplified and the output becomes the same as the power supply almost. (It is the saturation
state) Oppositely, when the positive input becomes lower a little than the negative input, the
difference is tens of thousands of times amplified and the output becomes 0 V almost.(It is in
SRTIST, NALGONDA 22
KEEP DISTANCE WARNING SYSTEM
the OFF condition) This operation is the same as the operation of the comparator. However,
because the inner circuit is different about the comparator and the operational amplifier, the
comparator can not be used .
CHAPTER 5
LCD DISPLAY CIRCUIT
5.1 INTRODUCTION:
The alphanumeric 16 character X 2line LCD requires 8data lines and also 3 control
signals and they are interfaced to 3664.By using 2 ports, port 0&3 data pins are connected to
LCD as data bus. Port0 can be basically used as I/O port i.e. it can be programmed as an
input or as an output port.
That means if it is programmed as output port, suppose if it is required to read data
from LCD immediately it is not possible. Before reading the data it is required to make the
port as an input port. Data reading from LCD gives an erroneous reading & should not be
implemented. Because of this port5 is made as input / output port depending on the situation.
The control signals are connected to port 3 pins. They are EN bar & RS bar, RW bar. At
different instance such as data write / command write / data read etc. Various signals are to
be provided as indicated by the by the LCD manufacturers.
To interface the LCD, to the Micro controller it require an 8 bit and also three
control signals differentiate the data from the control words send to the LCD. The Micro
controller has to send the necessary control words followed by the data to be displayed.
Depending on the operation to be performed the control words are selected and
passes to the LCD. The data to be displayed on the LCD is to be sent in the ASCII format.
Thus all the character to be displayed are converted into ASCII form and then sent to the
LCD along with different control words. The control word differentiated the various
operations and are executed. It is also possible to read the LCD data if required.
The control signals to the LCD are also provided by the Micro controller. This is
also done through pins 3.5,3.6&3.7.Through program necessary control signals are passed to
the LCD by using the bits of the port. The remaining can be used for some other purpose if
there is a need. The software controls the necessary ports and performs the task it is designed
SRTIST, NALGONDA 23
KEEP DISTANCE WARNING SYSTEM
for. The soft ware and associated hardware perform the LCD interface.
A liquid crystal is a material (normally organic for LCDs) that will flow like a
liquid but whose molecular structure has some properties normally associated with solids.
The Liquid Crystal Display (LCD) is a low power device. The power requirement is
typically in the order of microwatts for the LCD.
FIG (5.1.1) LCD DISPLAY
A liquid crystal is a material (normally organic for LCDs) that will flow like a liquid
but whose molecular structure has some properties normally associated with solids. The
Liquid Crystal Display (LCD) is a low power device. The power requirement is typically in
the order of microwatts for the LCD. However, an LCD requires an external or internal light
source. It is limited to a temperature range of about 0C to 60C and lifetime is an area of
concern, because LCDs can chemically degrade.
There are two major types of LCD s which are:
1) Dynamic-scattering LCD s
2) Field-effect LCD s
Field-effect LCD s are normally used in such applications where source of energy is a prime
factor (e.g., watches, portable instrumentation etc.).They absorb considerably less power
than the light-scattering type. However, the cost for field-effect units is typically higher, and
their height is limited to 2 inches. On the other hand, light-scattering units are available up to
8 inches in height. Field-effect LCD is used in the project for displaying the appropriate
SRTIST, NALGONDA
Gnd vcc preset rs rw en d0 d1 d2 d3 d4 d5 d6 d7 vcc gnd
LCD DISPLAY
24
KEEP DISTANCE WARNING SYSTEM
information. The turn-on and turn-off time is an important consideration in all displays. The
response time of LCD s is in the range of 100 to 300ms.The lifetime of LCD s is steadily
increasing beyond 10,000+hours limit. Since the colour generated by LCD units is
dependent on the source of illumination, there is a wide range of colour choice.
To send any of the commands from given table to the lcd, make pin RS =0.For data, make
RS=1.then send a high to low pulse to the E pin to enable the internal latch of the LCD. As
shown in figure for LCD connections.
Fig(5.1.2) 8-bit LCD interface
5.2 CONCLUSION:
Hence , we conclude that LCD is used for displaying the data.The data to be
displayed on the LCD is to be sent in the ASCII format. Thus all the character to be
displayed are converted into ASCII form and then sent to the LCD along with different
control words. It is also possible to read the LCD data if required.
SRTIST, NALGONDA 25
KEEP DISTANCE WARNING SYSTEM
CHAPTER 6
CIRCUIT DIAGRAM
SRTIST, NALGONDA 26
KEEP DISTANCE WARNING SYSTEM
CHAPTER 7
SOFTWARE DESCRIPTION
SRTIST, NALGONDA 27
KEEP DISTANCE WARNING SYSTEM
The software that we used in this project is Keil Micro vision 3, microflash. Keil micro
vision 3 is a complier. Microflash is used to burn software into hardware in AT89S52
PROGRAM:
#include<reg51.h>
sfr ldata=0x90; //port 1
sbit rs=P2^5;
sbit rw=P2^6;
sbit en=P2^7;
sbit usonic=P0^1;
sbit buzzer=P0^7;
lcddata(char temp[ ],int );
lcdcmd(unsigned char);
lcddelay(unsigned int);
main ( )
{
Buzzer =1;
Lcdcmd (0x38);
Lcdcmd (0x0E);
Lcdcmd (0x01);
Lcdcmd (0x81);
Lcddata ("KEEP DISTANCE",14);
While (1)
{
If (usonic==0)
{
Lcdcmd (0xC0);
Buzzer =0;
Lcddata ("VEHICLE AHEAD",13);
Lcdcmd (0x0C);
}
else
SRTIST, NALGONDA 28
KEEP DISTANCE WARNING SYSTEM
{
Buzzer =1;
Lcdcmd (0xC0);
Lcddata ("NO VEHICLE AHEAD",16);
Lcdcmd (0x0C);
}}}
Lcddelay (unsigned int k)
{
int i,j;
for (i=0;i<=k;i++)
for (j=0;j<=1275;j++);
}
lcdcmd (unsigned char value)
{
Ldata =value;
Rs =0;
Rw =0;
En =1;
Lcddelay (1);
En =0;
return;
}
Lcddata (char temp[16],int s)
{
For (s=0;s<16;s++)
Ldata =temp[s];
rs =1;
rw =0;
en=1;
lcddelay (1);
en =0 } }
CHAPTER 8
EXPERIMENTAL RESULTS & CONCLUSION
SRTIST, NALGONDA 29
KEEP DISTANCE WARNING SYSTEM
8.1 INTRODUCTION:
Most of the accidents in high-ways are happening due to the drowsiness of drivers,
most often this symptom is found in long distance truck drivers, these drivers may take some
time to recognize the opposite vehicle, which is running at low speed, resulting accident.
This kind of accidents may happen due to the drunken drivers also. So to increase safety an
electronic warning system is essential to alert the drivers. This kind of system can be
installed in all types of vehicles, especially in commercial vehicles, so that accident rate can
be minimized. The warning system designed here can be called as driver attention system,
which raises an alarm and energizes the display board automatically when the following
vehicle came near to the in-front running vehicle.
8.2 RESULTS:
The project work keep distance warning system that is designed for Automobiles,
any vehicle ranging from motor cycle to heavy duty truck can adopt this system. This alerts
the following vehicle whenever it came very close to the ahead vehicle; thereby to some
extent accidents can be avoided.
The circuit is designed such that whenever the infrared signal is interrupted, logic
high signal is generated and it is fed to microcontroller, on receipt of this signal, the
controller activates the display board and alarm automatically.
8.3 APPLICATIONS:
This system is best for guiding the perimeter of a house or a business center the
points where an intruder would enter the building. In this system IR sensor is used to detect
the intrusion. Similarly the vibration and temperature sensors recognize vibration
disturbances and accidental fires respectively.
This project provides an efficient and economical security system. This system finds
applications in industries, banks and homes.
8.4 FUTURE SCOPE:
This system is a rapidly growing field and there are new and improved strategies
SRTIST, NALGONDA 30
KEEP DISTANCE WARNING SYSTEM
popping up all the time. For the most part these systems are all built around the same basic
structure, a central box that monitors several detectors and perimeter guards and sounds an
alarm when any of them are triggered.
Incorporating the features discussed below can further enhance the system
This system can detect intrusion only at discrete points. This system detection
feature can be extended to scanning a complete area. Thus the intrusion into the building
can be detected with much more efficiently.
The redialing feature can also be incorporated such that if the call is not put
forward the first time, the auto dialer will dial the same number until the call is successfully
completed.
A pre-recorded voice message can delivered to the owner notifying him about the
intrusion into the premises.
The addition of the above discussed advancements certainly builds this project
into a much flexible and reliable security system.
8.5 CONCLUSION:
Hence, here by we conclude that Keep Distance Warning System is mainly used
to avoid accidents. This kind of system can be installed in all types of vehicles, especially in
commercial vehicles, so that accident rate can be minimized. This project provides an
efficient and economical security system.
BIBILOGRAPHY
REFERENCES:
The 8051 Microcontroller and Embedded Systems By Muhammad Ali Mazidi
Fundamentals Of Embedded Software By Daniel W Lewis
Datasheets of Microcontroller AT89C52
Datasheets of 555 timer
Datasheets of TSAL 6200
SRTIST, NALGONDA 31
KEEP DISTANCE WARNING SYSTEM
Datasheets of TSOP 1356
Datasheets of BC 547
Datasheets of DTMF Generator UM 95089
WEBSITE REFERENCES:
www.howsstuffworks.com
www.alldatasheets.com
www.electronicsforu.com
www.knowledgebase.com
www.8051 projectsinfo.com
SRTIST, NALGONDA 32
KEEP DISTANCE WARNING SYSTEM
APPENDIX-THEORY OF MICROCONTROLLER
A micro-controller contains a CPU, clock circuitry, ROM, Ram and I/O
circuitry on a single integrated circuit package. The Micro-controller is therefore, a
self-contained device, which does not require a host of associated support chips for its
operation as conventional microprocessors do. It offers several advantages over
conventional multi-chip systems. There is a cost and space advantage as extra chip
costs and printed circuit board and connectors required to support multi-chip systems
are eliminated. The other advantages include cheaper maintenance, decreased
hardware design effort and decreased board density, which is relevant in portable
control equipment. The microcontroller that we use is AT89S52.
Memory Organization of Microcontroller:
The total memory of 89S52 system is logically divided in Program memory
and Data memory. Program memory stores the programs to be executed, while data
memory stores the data like intermediate results, variables and constants required for
the execution of the program. Program memory is invariably implemented using
EPROM, because it stores only program code which is to be executed and thus it need
not be written into. However, the data memory may be read from or written to and
thus it is implemented using RAM.
Further, the program memory and data memory both may be categorized as
on-chip (internal) and external memory, depending upon whether the memory
physically exists on the chip or it is externally interfaced. The 89S52 can address
8Kbytes on-chip memory whose map starts from 0000H and ends at 1FFFH. It can
address 64Kbytes of external program memory under the control of PSEN (low)
signal.
The AT89S52 implements 256 bytes of on-chip RAM. The upper 128 bytes
occupy a parallel address space to the Special Function Registers. That means the
upper 128bytes have the same addresses as the SFR space but are physically separate
from SFR space. When an instruction accesses an internal location above address
7FH, the address mode used in the instruction specifies whether the CPU accesses the
upper 128 bytes of RAM or the SFR space. Instructions that use direct addressing
access SFR space.
SRTIST, NALGONDA 33
KEEP DISTANCE WARNING SYSTEM
SRTIST, NALGONDA 34
KEEP DISTANCE WARNING SYSTEM
SRTIST, NALGONDA 35