dodge avenger 2007-2008 charger 2008/dakota …

INSTALLATION INSTRUCTIONS FOR PART 99-6511

99-6511

APPLICATIONSChrysler

Aspen 2008/Sebring 2007-08Town and Country 2008/300/300c 2008

DodgeAvenger 2007-2008

Charger 2008/Dakota 2008/Durango 2008Grand Caravan 2008/Journey 2009

Magnum 2008/ Nitro 2007-08

Jeep Liberty 2008/Jeep Wrangler 2007-08

KIT FEATURES

• DIN Mount Radio Provision with Pocket• ISO Mount Radio Provision with Pocket

A) Radio Housing with Pocket • B) ISO Brackets • C) ISO Trim Plate

KIT COMPONENTS

A

TOOLS REQUIRED:Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION

www.metraonline.com

B C

Dash Disassembly- Chrysler Aspen 2008/Dodge Durango 2008 . . . . . . . . . . . . . . 1- Chrysler Sebring 2007 -08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- Chrysler Town and Country 2008 . . . . . . . . . . . . . . . . . . . . . 3,4- Chrysler 300/300C 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- Dodge Avenger 2007-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6- Dodge Dakota 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7- Dodge Grand Caravan 2008 . . . . . . . . . . . . . . . . . . . . . . . . . .3,4- Dodge Magnum/Charger 2008 . . . . . . . . . . . . . . . . . . . . . . . . .5- Dodge Nitro 2007-08/Liberty 2008 . . . . . . . . . . . . . . . . . . . . . .8- Dodge Journey 2009. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9- Jeep Commander/ Grand Cherokee 2008 . . . . . . . . . . . . . . . . . 10- Jeep Wrangler 2007-08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Kit Assembly- DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 12- ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . .13

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

TABLE OF CONTENTS

99-6511

*Note: Refer also to the instructions included with the aftermarket radio.

99-6511 DASH DISASSEMBLY

CHRYSLER ASPEN 2008DODGE DURANGO 2008

A

123

69

POWEROUTLET

1 2 3 4 5 6

POWEROUTLET

B

123

1 2 3 4 5 6

69

C

1

1

Remove (2) screws from bottom edgeof center dash trim panel. Unsnapand remove the panel. (Figure B)

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

3

Remove (4) screws securing theradio. Unplug and remove radio.(Figure C)

3

Unsnap and remove storage cup holder assembly. (Figure A)

2

Continue to kit assembly.


CHRYSLER SEBRING 2007-2008A

B

2

1

Remove (4) 7MM screws securingradio. Unplug and remove radio.(Figure B)


3

Unclip entire panel surrounding radioincluding a/c vents and clock. Unplugand remove panel. (Figure A)

2



CHRYSLER TOWN AND COUNTRY 2008DODGE GRAND CARAVAN 2008

A

B

C

3

1

Lift up on panel above radio thenremove (2) Phillips screws exposed atfront edge of radio trim panel.(Figure B)


3

Remove (3) plastic push pins per sideof bottom trim panel then slide paneltoward rear of van to access (2)screws on bottom of radio trim panel.(Figure C)

4

Remove (2) screw covers facing upabove radio then remove the (2)Phillips screws exposed. (Figure A)

2

Continued on page 3.


D

E

1 2 3 4 5 6 AUX

AUX

SET

VOLUME

PUSH ON PUSH AUDIO/SELECTAM

FM

DISC

LIST

MUSICTYPE

SEL;ECT

TUNE/SCROLL

SEEKSEEK SCAN TIME INFO RW FFU

F

4

5 Remove (2) Phillips screws exposedat bottom edge radio trim panel.(Figure D)

Remove (4) Phillips screws securingradio. (Figure F)

7

Unclip and remove entire panel sur-rounding radio including climate con-trols, vents and clock. (Figure E)

6


CHRYSLER TOWN AND COUNTRY 2008DODGE GRAND CARAVAN 2008


CHRYSLER 300/300C 2008DODGE MAGNUM/CHARGER 2008

1 2 3 4 5 6

1 2 3 4 5 6

B

5

1 Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

3 Remove (4) screws securing theradio. Disconnect and remove theradio. (Figure C)

Unsnap and remove center dash trimpanel. (Figure A)

2


A


DODGE AVENGER 2007-2008A

B

1 2 3 4 5 6 AUX

AUX

SET

VOLUME


FM

DISC

LIST

MUSIC TYPE

SEL;ECT

TUNE/SCROLL


CD

6

1

Unclip the center dash trim panel.(Figure B)


3

Remove (4) screws securing theradio. Disconnect and remove theradio. (Figure C)

Remove (3) screws securing the radiorear support bracket and remove thebracket. (Figure D)

4

5

Unclip and remove the center consoletrim panel. (Figure A)

2



DODGE DAKOTA 2008A

1 2 3 4 5 6 AUX

AUX

SET

VOLUME


FM

DISC

LIST

MUSICTYPE

SEL;ECT

TUNE/SCROLL


B

7

1

Remove (4) Phillips screws securingthe radio. (Figure B)


3

Unclip and remove the trim panel sur-rounding the radio. (Figure A)

2



DODGE NITRO 2007-2008JEEP LIBERTY 2008

A

61 2 3 4 5

2 3 4 5 61

B

8

1



3

Unclip entire panel surrounding radioand climate controls, including a/cvents. Unplug and remove panel.

2



DODGE JOURNEY 2009

A

1 2 3 4 5 6 AUX

AUX

SET

VOLUME


FM

DISC

LIST

MUSIC TYPE

SEL;ECT

TUNE/SCROLL


POWEROUTLET

1 2 3 4 5 6 AUX

AUX

SET

VOLUME


FM

DISC

LIST

MUSICTYPE

SEL;ECT

TUNE/SCROLL

PUSH PUSH

OFF

PUSH

OUTLET

POWEROUTLET

B

9

1

Remove (4) 7MM screws securingradio to dash to remove. (Figure B)


3

Unclip and remove the entire factoryradio trim panel including the a/ccontrols. (Figure A)TIP: Open the compartment door at the

top of the radio trim panel.

2



JEEP COMMANDER/GRAND CHEROKEE 2008

A

B

POWEROUTLET

C

1 2 3 4 5 6 AUX

AUX

SET

VOLUME


FM

DISC

LIST

MUSIC TYPE

SEL;ECT

TUNE/SCROLL


D

10

1

Unsnap and remove the larger trimaround the console shifter. (Figure B)


3

Unsnap and remove the small trimaround the console shifer. (Figure A)

2

Unsnap and remove the dash panelfrom around the radio (including cli-mate controls). (Figure D)

5

Remove (4) Phillips screws securingthe radio. Unplug and remove radio.

6

Remove one Phillips screw frominside the small storage pocket in thelower dash, between the power outl-lets. (Figure C)

4



JEEP WRANGLER 2007-08

A

1 2 3 4 5 6

1 2 3 4 5 6

B

11

1

Remove (2) Phillips screws exposedbehind lower center panel. (Figure A)


3

Unclip and remove the lower centertrim below a/c controls. (Figure A)

2

Remove (2) Phillips screws exposedbehind upper center panel. (Figure A)

5

Unclip and remove entire panel sur-rounding radio and climate controls,including a/c vents.

6


7

Unclip and remove the upper centertrim starting towards the rear of thepanel. (Figure A)

4


99-6511 KIT ASSEMBLY

12

A

B

DIN MOUNT RADIO PROVISION WITH POCKET

Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A)

1

Slide the aftermarket radio into the DINcage until it snaps into place. (Figure B)

2

Continue to final assembly.


99-6511 KIT ASSEMBLY

13

A

B

ISO MOUNT RADIO PROVISION WITH POCKET

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)

1

Slide the radio into the radio openinguntil it snaps into place. (Figure B)

2

Snap the ISO Trim Plate onto the frontof the Radio Housing. (Figure B)

3

Continue to final assembly.


99-6511 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black*NOTE: When a Black wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer’s specifications.

14

1-800-221-0932 REV. 04/08/08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST99-6511

www.metraonline.com

Pacific Accessory Corporation® | Clearwater, FL 33760 | Ph. 866-931-8021 | [email protected] ©2015 Pacific Accessory Corporation

www.pac-audio.com

Pacific Accessory Corporation

RP4-CH11Radio Replacement & Steering Wheel Control Interface

for Chrysler/Dodge/Jeep Vehicles

Rev. 012015

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The RP4-CH11 interface allows the replacement of a factory radio in select Chrysler/Dodge/Jeep vehicles with MSCAN or LSFT-CAN databus radios. Using this interface will retain factory features such as steering wheel controls (SWC) vehicle entertainment system (VES) and the factory audio amplifier whenever the original radio is removed. Use of this interface also allows you to program two radio functions to each SWC button by using short press long press dual command functionality. The RP4-CH11 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake.

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the vehicle (see next page for setting chart).

2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to flash 4 times.

3. The LED will flash whenever a SWC button is pressed.

Red / White Parking Brake Output (-)

Purple / White Vehicle Speed Output

Blue / White Amp Turn On InputRed Accessory Output

Output (1 amp)Orange / White Illumination Output

(+)Green Reverse Output (+)

Interface Connector

Yellow Battery +12vBlack GroundBlue Antenna On InputWhite Front L + input

White / Black Front L - inputGrey Front R + input

Grey / Black Front R - inputGreen Rear L + input

Green / Black Rear L - inputPurple Rear R + input

Purple / Black Rear R - input

Vehicle Connector SWC Connector

Blu/Yel Kenwwod, Newer JVC

3.5mm Jack Alpine, JVC, Clarion, Fusion, Pioneer, Sony,

Boyo, Dual, Lightning Audio,

Visteon or Advent

Aftermarket RadioConnections

Vehicle Connector

SWC Connection

x4

See above chart for different radio type connections

Acc On/Programming LED

Programming Button

Wiring SWC Connection

Page 1


www.pac-audio.com




Rev. 012015

Default Steering Wheel Control Programming

IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless you wish to re-assign the SWC functions or utilize *short press long press dual command functionality. The SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to flash 4 times.

Installation Steps

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the vehicle.

2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your particular vehicle.

3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplifier: Connect the aftermarket radio’s front and rear speaker wires to the vehicle connector. Vehicles with a factory amplifier: The factory amplifier only accepts two channels of audio input (left and right). Connect the front outputs of the aftermarket radio to the rear inputs of the vehicle connector. This will allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. Fading is not supported in this application. The factory amplifier’s fading is controlled by data communication from the factory radio. Neither the aftermarket radio or the RP interface have the ability to control the amplifier’s fader.

4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)5. If you wish to reassign functions to the SWC or utilize short press long press dual command functionality. follow the programming instructions

on the next page.

Default SWC Button AssignmentsAlpine JVC Kenwood Clarion Sony/Pioneer Fusion

Volume + Volume + Volume + Volume + Volume + Volume + Volume +Volume - Volume - Volume - Volume - Volume - Volume - Volume -Source Source Source Source Source Source SourceTrack + Track + Track + Track + Search + Track + Track +Track - Track - Track - Track - Search - Track - Track -Preset + Preset + Preset Disc/Radio + Band Preset + AudioVoice Mute Mute Mute Mute Mute MutePhone Receive Receive Answer Send/End Answer Power

Page 2

Short Press Long Press Dual Command FunctionalityThis feature allows you to assign two aftermarket radio functions to each of the vehicles SWC buttons. It can be used with as many of the buttons as the user likes or none at all. When this functionality is implemented, quickly pressing and releasing a SWC button will initiate the short press command while pressing and holding a SWC button for longer than two seconds will initiate the long press command. Please note that no long press commands are programmed by default. If you wish to assign dual command functionality to the SWC please follow the programming steps on the next page.

1 2 3 4 5 6 7 8 9

0

Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion1 2 3 4 7 8 9

Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon

SET RADIO SELECT SWITCH


www.pac-audio.com




Rev. 012015

Alpine JVC Kenwood Clarion Other* Pioneer Sony Fusion1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -3 Mute Mute Mute Mute Mute Mute Mute Mute4 Preset + Source Source Source Preset + Preset + Preset + Source5 Preset - Track + Play Search + Preset - Preset - Preset - Track +6 Source Track - Track + Search - Source Source Source Track -7 Track + Band/Disc + Track - Band Track + Track + Track + Audio8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power9 Power Select Disc/AM - Send Band Band Band

10 Enter/Play Attenuation Answer End N/A Phone MenuReject Call/Source

(Bluetooth equipped radios only)

11 Band/Program Phone Receive Voice Dial Answer Call Answer/End Call12 Receive Phone Reject On Hook End Call13 End Voice Dial Off Hook VR

14 VR Power Mute (Multimedia units only)

15 Preset +*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon

Optional Programming Order

Optional Steering Wheel Control Programming

If you wish to re-assign the SWC functions or utilize short press long press dual command functionality, the interface must be programmed in the specific order shown on the chart below. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and release the program button on the side of the interface to skip that function. The LED will flash off and on confirming that you have successfully skipped that function and are ready to proceed to the next one.

Page 3Page 2

1. Turn the key to the ignition position.2. Press and release programming button on the side of the interface.3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn off when the button is pressed.

At this point you have two options:A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on. B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED will

go back to solid.4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and

release the program button on the side of the interface to skip that function. 6. Once programming is completed, wait seven seconds. The LED will flash three times indicating end of programming.7. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function

does not work, repeat the programming steps

1 2 3 4 5 6 7 8 9

0

Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion1 2 3 4 7 8 9

Other = Advent, BOYO, Dual, Lightning Audio, Rockford Fosgate, Visteon

SET RADIO SELECT SWITCH


www.pac-audio.com




Rev. 012015

Product Updates (Firmware)The RP4-CH11 can be updated with new firmware as it becomes available using the PAC-UP interface updater (sold seperatly). Please visit www.pac-audio.com/firmware for available updates.

Vehicle Entertainment System (VES); If equipped1. Vehicles equipped with a DVD player built into the rear screen assembly: The RP4-CH11 will allow the VES DVD

player and rear screen to function as if the factory radio were present. A/V will be passed from the factory DVD player to the rear screen and audio can be heard through the headphones. A/V cannot be passed from the factory DVD player to the aftermarket head unit.

2. Vehicles equipped with a stand alone VES DVD Player: The RP4-CH11 will allow the VES DVD player and rear screen(s) to function as if the factory radio were present. A/V will be passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones. A/V can also be fed from the VES DVD player into an aftermarket head unit (head unit must support A/V in) with the use of the CHYRVD (please check vehicle compatibility). It is VERY IMPORTANT that the RP4-CH11 Blue/White remote input wire be connected for this feature to function properly!

3. Vehicles not equipped with a VES DVD Player (rear screen(s) only): In this application the CHYRVD (please check vehicle compatibility) must be used in order to feed A/V into the factory screen(s) from an aftermarket head unit (head unit must support A/V out). With the CHYRVD, A/V will be passed from the aftermarket head unit to the rear screen(s) and audio can be heard through the headphones. If you wish to retain the Auxiliary inputs on the rear of the console you must disconnect the factory wires from the auxiliary input then connect and run your own RCAs into the aftermarket head unit.

4. Vehicles equipped with a Reverse Camera: In order to retain the factory reverse camera the CHYRVD (please check vehicle compatibility) must be used to feed video into the aftermarket head unit (head unit must support reverse camera input).

Testing & Verification1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.

2. Turn on the radio & check balance & fade. Note: Factory amplified Systems will not fade as neither the aftermarket radio or the RP interface have the ability to control the amplifier’s fader.

3. Verify that the factory subwoofer (if present) is playing

4. Verify that all SWC are functioning properly.

5. Turn off vehicle & remove key. RAP will be active & keep the radio on for 10 minutes or until the drivers door is opened.

6. The LED & radio will turn off when RAP turns off or the drivers door is opened.

Page 4

PLEASE NOTE: If after installation the text on the driver information center has changed to German you will need to visit a dealer and change the vehicle’s country code to U.S.A.

dodge avenger 2007-2008 charger 2008/dakota …

Documents