CAT-57164June 2008 Overseas Dept.
CAT-57164June 2008 Overseas Dept.
Structure
Size Variations
New and Wide Variations of Miniature Type Cam Followers
Metric Series CF Miniature Series CFS
CF···BUU
CF···WBUUR CFS···W
CFS
CFS
CFS
CF
CF
CFS···V
CF 3
10 12 13
12108654.54
65432.521.4
CF 4
CFS 4 CFS 5 CFS 6CFS 3CFS 2.5CFS 2CFS 1.4
CF 5
This is a miniature version of metric series CF which is the basic type of Cam Follower. Various shapes and sizes are available.
21
Miniature Type Cam Follower series meets miniaturization demands of advanced equipment.
Outer Ring Needle Roller
Stud
Thrust Washers
Hexagon Nut
1.4mmMicro Cam Follower CF1.4WV of stud dia. of 1.4 mm and outside dia. of outer ring of only 4 mm The built-in thrust washers receive axial loads that may occur due to mounting errors.
Five major features
Seal Cage
Thrust Washer Thrust Washer
Cage Cage
Cage
Seal
Stud
Stud Stud
Stud
End Plate
Needle Roller
Outer Ring
End Plate
Needle RollerOuter RingOuter Ring End Plate
Needle Roller
End Plate
Needle Roller
Outer Ring
Stud
End Plate
Needle Roller
Outer Ring
This series has extremely fine needle rollers assembled in the outer ring so that the outside dia. of outer ring is not so great in comparison with the stud dia.. Cam Followers of this series are used for electronic parts/device, OA equipment, small indexing equipment and so on. Standard Type Cam Follower
Cam Follower with Thrust Washers Miniature Type Cam Follower with Thrust Washers
Miniature Type Cam Follower
Metric Series CF
Metric Series CF
Miniature Series CFS
Miniature Series CFS
1 2 3 4 5CFS1.4WV
Resistant to mounting errorsCam Follower with
Thrust Washers
Debut of smallest Cam Followers in the world with a stud dia. of only 1.4 mm
Stud dia. of only 1.4 mm
Outside dia. of outer ring of only 4 mm
With a hexagon socket hole for easy mounting
Full Complement type of great load capacity
With thrust washers resistant to mounting errors
Stud dia. of only 1.4 mm
Outside dia. of outer ring of only 4 mm
With a hexagon socket hole for easy mounting
Full Complement type of great load capacity
With thrust washers resistant to mounting errors
TypeCaged or
Full complementSeal
structureMaterial Model codeShape of outer ring
Stud diameter(mm)
Shape ofstud head
Miniature Type Cam Followers series are designed to be
very compact; stud dia. of 1.4mm to 6 mm and outside dia. of
outer ring of 4 mm to 13 mm. This series is suitable for light-
loaded high-accuracy cam mechanisms and linear motion
follower bearings. This series can be used in very wide fields
such as equipment for electronic parts, precision measuring
devices, and office appliance.
Cam Followers with Thrust Washer has particular plastic thrust
washers of high wear and heat resistances in the thrust
contact parts between the outer ring and the stud head (and
between the outer ring and the end plate). The washers
receive axial loads of the outer ring due to mounting errors
and prevent friction and abrasion of the sliding surface.
Stainless Steel Made Cam Followers excels at corrosion resis-
tance and is also available in oil-inhibited areas, water-mist
environment and clean room.
Outside dia.of outer ring
D (mm)
Outside dia.of outer ring
D (mm)
Stud dia.d1 (mm)
Standard Type Cam Follower
Cam Follower with Thrust Washers
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
3 – 5
CF···BR
CF···BUUR
CF···B
CF···BUU
CF···FBR
CF···FBUUR
CF···FB
CF···FBUU
CF···WBR
CF···WBUUR
CF···FWBR
CF···FWBUUR
Shield type
Sealed type
Shield type
Sealed type
Shield type
Sealed type
Shield type
Sealed type
Shield type
Sealed type
Shield type
Sealed type
Crowned outer ring
Cylindrical outer ring
Crowned outer ring
Cylindrical outer ring
Crowned outer ring
Crowned outer ring
Hex socket
Hex socket
High carbon steel
Stainless steel
High carbon steel
Stainless steel
Caged
Caged
Miniature Type Cam Follower
Miniature Type Cam Follower with Thrust Washers
2 – 6
2 – 6
2 – 6
2 – 6
2 – 6
2 – 6
1.4
CFS
CFS···F
CFS···V
CFS···FV
CFS···W
CFS···FW
CFS···WV
Shield type
Shield type
Shield type
Shield type
Shield type
Shield type
Shield type
Cylindrical outer ring
Cylindrical outer ring
Cylindrical outer ring
Cylindrical outer ring
Cylindrical outer ring
Cylindrical outer ring
Cylindrical outer ring
Hex socket
Hex socket
High carbon steel
Stainless steel
High carbon steel
Stainless steel
High carbon steel
Stainless steel
High carbon steel
Caged
Full complement
Caged
Full complement
∆DmpSingle plane mean outside dia. deviation
Examples of identification number
Example of Thrust Disk Type Cam Followers
Example of Miniature Type Cam Followers
CF 5
3 F
W
V
B UU R
P6CFS
Identification Number
3
The identification number examples of Miniature TypeCam Followers are shown below.
4
Accuracy
Tolerances of Miniature Type Cam Followers series areshown in table 1, Table 2.1 and Table 2.2.
Fit
The recommended tolerance of mounting hole for the stud isH7 for Metric Series CF and H6 for Miniature Series CFS.The mounting hole diameter should be prepared without playbetween the stud and the hole especially when heavy shockloads may be applied.
Maximum Allowable Load
The applicable load on Cam Followers is, in some cases,limited by the bending strength and shear strength of the studand the strength of the outer ring instead of the load rating ofthe needle roller bearing. Therefore, the maximum allowablestatic load is specified by the limitations of those strengths.
Type
Dimensionsand symbols
Metric series CF
Crownedouter ring
0
-50
h7
0
-120
0
-120
h6
See Table2.1
See Table 2.2
Cylindricalouter ring
Miniature seriesCFS
Table 1 Tolerances unit: μm
Out side dia. of outerring
Stud dia. d1
Width of outer ring C
∆DmpSingle planemean outsidedia. deviation
High Low
0 -8
VDp
Outside dia.variation in asingle radial
plane
10 6 15
VDmp
Mean outsidedia. variation
Kea
Radial runoutof assembledbearing outer
ring
Table 2.1 Accuracy of outer ring(for cylindrical outer ring of Metric series CF)
unit: μm
class 0 class 6 class 5 class 4 class 0 class 6 class 5 class 4
High Low High Low High Low High Low
0 -8 0 -7 0 -5 0 -4 15 8 5 4
KeaRadial runout of
assembled bearingouter ring
Table 2.2 Accuracy of outer ring(for Miniature series CFS) unit: μm
Model code(1)
Metric series CF
CF3~CF5
―
Miniature series CFS
CFS1.4~CFS5
CFS6
Radial internalclearance
Min.
3
5
Max.
17
20
Table 3 Radial internal clearance unit: μm
Note(1) Only representative types are shown in the table, but applicableto all metric series.
Nominal outside dia.of stud
mm
H6 H7
over incl High Low High Low
―
3
3
6
+6
+8
0
0
+10
+12
0
0
Table 4 Tolerances of mounting hole unit: μm
Clearances
Internal clearances of Miniature Type Cam Followers series are
shown in Table 3.
Model code
Metric SeriesCF
MiniatureSeries CFS
Standard Type CamFollowers
Thrust Disk Type CamFollowers
Miniature Type CamFollowers
Thrust Disk Type MiniatureCam Followers
CF
CF…W
CFS
CFS…W
Size
Stud dia. (Unit: mm)
Material code
No symbol
F
Carbon steel
Stainless steel
Roller guiding method
No symbol
V
Caged type
Full complement type
Shape of stud head
B
No symbol
With Hexagon Hole (CF series)
With Hexagon Hole (CFS series)
Seal structure
No symbol
UU
Shield type
Sealed type
Shape of outer ring
R
No symbol
Crowned outer ring
Cylindrical outer ring
Accuracy class
No symbol
P6
P5
P4
Accuracy class / class 0
Accuracy class / class 6
Accuracy class / class 5
Accuracy class / class 4
Applicable toMiniatureSeries CFS
1N=0.102kgf=0.2248lbs.1mm=0.03937inch
65
Allowable RotationalSpeed
Track Capacity Lubrication Hole
Mounting
Metric series CF having a stud dia. 5mm has an oil hole in the
stud-head. Cam Follower with a hexagon hole in the stud-head is
applied through the lubrication plug inside of the hexagon hole in
the stud-head. (See Fig. 1)
For replenishing of grease, mount an appropriate supply nozzle
(shown in Table 9) on the straight type grease gun of JIS B9808
(1991), push the nozzle against the grease nipple and the
lubrication plug, and gently apply the grease. Structurally, other
Metric series CF and Miniature series CFS cannot be re-lubricated.
Accessories
In Miniature Type Cam Followers series, nuts are attached.Track capacity is defined as a load which can be continuously
applied on a Cam Follower placed on a steel track surface without
causing deformation or indentation on the track surface when the
outer ring of the Cam Follower makes contact with the mating track
surface (plane). The track capacities shown in Table 5 are
applicable when the hardness of the mating track surface is 40HRC
(Tensile strength 1250N/mm2). When the hardness of the mating
track surface differs from 40HRC, the track capacity is obtained by
multiplying the value by the track capacity factor shown in Table 6.
If lubrication between the outer ring and the mating track surface is
insufficient, seizure and/or wear may occur depending on the
application. Therefore, attention must be paid to the lubrication and
the surface roughness of the mating track especially for high-speed
operation such as cam mechanisms.
Type(1)
Metric seriesCF
Miniatureseries CFS
Model codeCrownedouter ring
CF 3 R
CF 4 R
CF 5 R
―
―
―
―
―
―
―
542
712
794
―
―
―
―
―
―
―
CF 3
CF 4
CF 5
CFS 1.4
CFS 2
CFS 2.5
CFS 3
CFS 4
CFS 5
CFS 6
1 360
1 790
2 210
128
220
298
485
799
1 210
1 680
Trackcapacity
Model codeCylindricalouter ring
Trackcapacity
Table 5 Track capacity unit: N
Note(1) Only representative types are shown in the table, but applicableto all metric series.
HardnessTensile strength
N/mm2
Track capacity factor
Crowned outer ring Cylindrical outer ring
20
25
30
35
38
40
42
44
46
48
50
52
54
56
58
760
840
950
1 080
1 180
1 250
1 340
1 435
1 530
1 635
1 760
1 880
2 015
2 150
2 290
0.22
0.31
0.45
0.65
0.85
1.00
1.23
1.52
1.85
2.27
2.80
3.46
4.21
5.13
6.26
0.37
0.46
0.58
0.75
0.89
1.00
1.15
1.32
1.51
1.73
1.99
2.29
2.61
2.97
3.39
Table 6 Track capacity factor
The allowable rotational speed of Miniature Type Cam Followers
series are affected by mounting and operating conditions. For
reference, Table 7 shows d1n values when only pure radial loads
are applied. Considering that axial loads also act under actual
operating conditions, the recommended d1n value is 1/10 of the
value shown in the table.
Pre-Packed Grease andOperating Temperature
Grease pre-packed Miniature Type Cam Followers series is
ALVANIA GREASE S2 (SHELL), which can be used within the
temperature range shown in Table 8.
Lubricant
Type
Caged type
Full complement type
84 000
42 000
Grease
Table 7 d1n values of Miniature Type Cam Followersseries
Note d1n value =d1×n
where, d1:Stud diameter mmn:Rotational speed rpm
Type
Size of stud dia.d1 mm
Caged type Fullcomplement
typeShieldtype
Sealedtype
Metric seriesCF
Carbon steel
Stainlesssteel
3, 4- 20°C~
110°C(1)- 20°C~
80°C
- 20°C~80°C
―- 20°C~
120°C
―
―
- 20°C~120°C
―
―
―
- 20°C~120°C
- 20°C~120°C
- 20°C~110°C(1)
- 20°C~120°C
5
- 20°C~80°C
―- 20°C~
110°C(1)3~5
1.4
2
2.5~6
Miniature series CFS
Table 8 Operating temperature range
Note(1) The maximum allowable temperature is +100˚C when they arecontinuously operated.
qSet the center axis of the mounting hole perpendicularly to the
moving direction of the Cam Follower and match the side shoulder
accurately with the seating surface indicated by dimension “ f ” in
the dimension tables. (See Fig.2) Then, fix the Cam Followers
directly with a hammer, etc. This may lead to a bearing failure such
as irregular rotation or cracking.
Fig.2 Seating surface
ƒ
Lubrication plug
Fig.1 Oil hole position
wThe mark on the stud-head indicates the position of oil
hole on the raceway. Avoid locating the oil hole within the loading
zone. This may lead to short a bearing life. (Refer to Fig.3)
eWhen tightening the nut, the tightening torque should not exceed
the values shown in the dimension tables. If the tightening torque
is too large, it is possible that the threaded portion of the stud can
be broken. When there is a possibility of loosening, a special nut
such as a lock nut, spring washer or self-locking nut should be
used.
Oil hole
Load
Fig.3 Oil hole position and loading direction
Type Shape and dimensionApplicable
grease nipple orlubrication plug
Lubricationplug(1)
A-5126T
φ1.
5
PT1/8
29
φ5
126
17°
Width across flats 12
Width acrossflats 12
Note(1) HSP-3 (by Yamada Corp.) is also available to lubricate.Remark Supply nozzles shown in the table can be mounted on the main
body of a common grease gun available on the market (shownbelow). If these supply nozzles are required, consult byspecifying the supply nozzle type.
Table 9 Applicable supply nozzles
Main body of grease gun
Supply nozzle
1N=0.102kgf=0.2248lbs.1mm=0.03937inch
1N=0.102kgf=0.2248lbs.1mm=0.03937inch
8
9
10
17
20
23
9
11
13
0.5
0.5
0.5
2
2.5
3
0.2
0.3
0.3
6.8
8.3
9.3
0.34
0.78
1.6
1 500
1 200
2 070
1 650
2 520
1 930
1 020
813
1 590
1 270
2 140
1 730
384
384
834
834
1 260
1 260
Mountingdimension
f
Min.
mm
Maximumtightening torque
N・m
Basic dynamicload rating
C
N
Basic staticload rating
C0
N
Maximumallowable load
NB B1 B2 C1 H rsmin(3)
Stud dia.
mm
3
4
5
Identification number Mass(Ref.)
g
Boundary dimensions mm
Shield type
Crownedouter ring
CF 3 BR
CF 3 FBR
CF 4 BR
CF 4 FBR
CF 5 BR
CF 5 FBR
CF 3 B
CF 3 FB
CF 4 B
CF 4 FB
CF 5 B
CF 5 FB
CF 3 BUUR
CF 3 FBUUR
CF 4 BUUR
CF 4 FBUUR
CF 5 BUUR
CF 5 FBUUR
CF 3 BUU
CF 3 FBUU
CF 4 BUU
CF 4 FBUU
CF 5 BUU
CF 5 FBUU
4.3
7.4
10.3
10
12
13
7
8
9
3
4
5
M3×0.5
M4×0.7
M5×0.8
5
6
7.5
Cylindricalouter ring
Crownedouter ring
Cylindricalouter ring
D C d1 G G1Sealed type
Note(1) Oil hole is not prepared.(2) The stud-head has an oil hole (lubrication plug).(3) Minimum allowable value of chamfer “r ”.
Remark Grease is pre-packed.
87
Standard Type Cam Followers with Hex Head
CF… B (With Cage)CF…FB (With Cage / Stainless steel)
CF… BRCF…FBR
CF… BCF…FB
Stud dia.3.4mm(1)
CF… BUURCF…FBUUR
CF… BUUCF…FBUU
CF 5 BRCF 5 FBR
CF 5 BCF 5 FB
CF 5 BUURCF 5 FBUUR
CF 5 BUUCF 5 FBUU
Stud dia. 5mm(2)
1N=0.102kgf=0.2248lbs.1mm=0.03937inch
8
9
10
17
20
23
9
11
13
0.5
0.5
0.5
2
2.5
3
6.8
8.3
9.3
0.34
0.78
1.6
1 500
1 200
2 070
1 650
2 520
1 930
1 020
813
1 590
1 270
2 140
1 730
384
384
834
834
1 260
1 260
Mountingdimension
f
Min.
mm
Maximumtightening torque
N・m
Basic dynamicload rating
C
N
Basic staticload rating
C0
N
Maximumallowable load
NB B1 B2 C1 H
Stud dia.
mm
3
4
5
Identification number Mass(Ref.)
g
Boundary dimensions mm
Shield type
CF 3 WBR
CF 3 FWBR
CF 4 WBR
CF 4 FWBR
CF 5 WBR
CF 5 FWBR
CF 3 WBUUR
CF 3 FWBUUR
CF 4 WBUUR
CF 4 FWBUUR
CF 5 WBUUR
CF 5 FWBUUR
4.3
7.4
10.3
10
12
13
7
8
9
3
4
5
M3×0.5
M4×0.7
M5×0.8
5
6
7.5
D C d1 G G1Sealed type
Note(1) Oil hole is not prepared.(2) The stud-head has an oil hole (lubrication plug).
Remark Grease is pre-packed.
109
Stud dia.3.4mm(1) Stud dia. 5mm(2)
Cam Followers with Thrust Washer / with Hex Head
CF… WB (With Cage)CF…FWB (With Cage / Stainless steel)
CF… WBRCF…FWBR
CF… WBUURCF…FWBUUR
CF 5 WBRCF 5 FWBR
CF 5 WBUURCF 5 FWBUUR
1N=0.102kgf=0.2248lbs.1mm=0.03937inch
Stud dia.
mm
2.5
3
4
5
6
Identification number Mass(Ref.)
g
Boundary dimensions mm
With cage Full complement
CFS 2.5―
―CFS 2.5 V
CFS 2 F―
―CFS 2 FV
―CFS 3 V
―CFS 4 V
―CFS 5 V
―CFS 6 V
―CFS 2.5 FV
―CFS 3 FV
―CFS 4 FV
―CFS 5 FV
―CFS 6 FV
CFS 2.5 F―
CFS 2―
―CFS 2 V
CFS 3―
CFS 3 F―
CFS 4―
CFS 4 F―
CFS 5―
CFS 5 F―
CFS 6―
CFS 6 F―
1
2
4
7
13
5
6
8
10
12
3
4
5
6
7
2.5
3
4
5
6
M2.5×0.45
M3 ×0.5
M4 ×0.7
M5 ×0.8
M6 ×1
2.5
3
4
5
6
4.5
5.5
7
8
9.5
D C d1 G G1 B
2 0.6 4.5 2.5 2 M2 ×0.4 2 4
1211
Miniature Type Cam Followers
CFS (With Cage) CFS… V (Full complement)CFS…F (With Cage / Stainless steel) CFS…FV (Full complement / Stainless steel)
B1
B2
C1
G1
d1
GD
C
H
B
Remark Oil hole is not prepared.
Grease is pre-packed.
CFSCFS…F
9.5
11.5
15
18
21.5
5
6
8
10
12
0.7
0.7
1.0
1.0
1.2
0.9
1.3
1.5
2
2.5
4.8
5.8
7.7
9.6
11.6
18.7
33.5
77.7
158
268
288
768
629
1 420
504
1 140
1 120
2 370
897
1 900
1 570
3 180
1 250
2 540
2 090
4 610
1 670
3 690
202
734
611
1 790
488
1 430
1 120
3 000
894
2 400
1 850
4 700
1 480
3 760
2 200
6 250
1 760
5 000
202
229
428
1 000
342
800
351
1 080
281
862
351
360
230
614
161
587
161
229
281
360
484
484
484
484
919
919
894
919
1 570
1 570
1 480
1 570
2 150
2 150
1 760
2 150
Mountingdimension
f
Min.
mm
Maximumtightening torque
N・m
Basic dynamicload rating
C
N
Basic staticload rating
C0
N
Maximumallowable load
NB1 B2 C1 H
CFS…VCFS…FV
8 4 0.7 0.9 4.3 9.1
B1
B2
C1
G1
d1
GD
C
H
B
ƒ
1N=0.102kgf=0.2248lbs.1mm=0.03937inch
481
288
230
428
342
629
504
1120
897
1570
1250
2090
1670
385
202
161
351
281
611
488
1120
894
1850
1480
2200
1760
105
194
161
313
281
399
399
785
785
1370
1370
1920
1760
Mountingdimension
f
Min.
mm
Maximumtightening torque
N・cm
Basic dynamicload rating
C
N
Basic staticload rating
C0
N
Maximumallowable load
NB2 C1 H
3.3
4
5
6
8
10
12
0.7
0.7
0.7
0.7
1
1
1.2
0.9
0.9
0.9
1.3
1.5
2
2.5
3.8
4.3
4.8
5.8
7.7
9.6
11.6
3.0
9.1
18.7
33.5
77.7
158
268
Stud dia.
mm
2.5
3
4
5
6
Identification number Mass(Ref.)
g
Boundary dimensions mm
With cage Full complement
―
CFS 2 W
CFS 2 FW
CFS 2.5 W
CFS 2.5 FW
CFS 3 W
CFS 3 FW
CFS 4 W
CFS 4 FW
CFS 5 W
CFS 5 FW
CFS 6 W
CFS 6 FW
CFS 1.4 WV
―
―
―
―
―
―
―
―
―
―
―
―
0.35
0.6
1
2
4
7
13
4
4.5
5
6
8
10
12
1.7
2.5
3
4
5
6
7
1.4
2
2.5
3
4
5
6
M1.4×0.3
M2 ×0.4
M2.5×0.45
M3 ×0.5
M4 ×0.7
M5 ×0.8
M6 ×1
1.4
2
2.5
3
4
5
6
3.7
4.5
5
6.5
8
9
10.5
7
8.5
10
12.5
16
19
22.5
D C d1 G G1 B B1
2
1.4
Remark Oil hole is not prepared.
Grease is pre-packed.
1413
Miniature Cam Followers with Thrust Washer
CFS… W (With Cage) CFS…WV (Full complement)CFS…FW (With Cage / Stainless steel)
CFS… WCFS…FW
B1
B2
C1
G1
d1
GD
C
H
B
ƒ
CFS1.4 WV
Suppresses machine designing and device costs
Minimizes the amount of lubricant andcontributes to the earth environment
Maintenance work can be reduced greatly
Suppresses machine designing and device costs
Minimizes the amount of lubricant andcontributes to the earth environment
Maintenance work can be reduced greatly
Requires no periodical lubrication and
increases the productivity.
Contributes to the earth environment
and reduces the running cost.
Working spaces
can be utilized.
Requires no periodical lubrication and
increases the productivity.
Contributes to the earth environment
and reduces the running cost.
Working spaces
can be utilized.
C-Lube BearingCAT-57165Maintenance Free
“C-Lube bearings” are ’s unique maintenance free bearing products with thermosetting solid lubricant (Capilube) pre-packed in the bearing space.As the bearing rotates, the lubricating oil oozes out onto needle rollers and raceways in proper quantity keeping the lubrication performance for a long period of time.
1
2
3
4
■For shaft support ■For cam mechanisms and follower bearings
C-Lube Machined Type Needle Roller Bearing C-Lube Cam Followers
Outer Ring
Needle Roller
Cage
Stud with Hexagon Socket Hole
With Seals
Thrust Washer
Outer Ring
Cage
C-Lube Unit
Capilube
Capilube
What is your trouble?
Find solutions with
Hard access to lubricating?
Machines and work places are dirty with lubricant?
Lubricating tools and instruments occupy the working places?
Having problems keeping up with lubrication maintenance schedule?
15 16
World Network of
1817
Unit G, 23rd Floor, Zhao Feng World Trade BuildingNo.369, Jiang Su RoadChangning District, Shanghai 200050People's Republic of ChinaPhone: +86 (0)21-5237-9100Fax: +86 (0)21-5237-9095E-mail: [email protected]
East coast
Midwest
West coast
91 Walsh DriveParsippany, NJ 07054U.S.A.Phone: +1 973-402-0254Toll Free: 1-800-922-0337Fax: +1 973-402-0441E-mail : [email protected]
500 East Thorndale AvenueWood Dale, IL 60191U.S.A.Phone: +1 630-766-6464Toll Free: 1-800-323-6694Fax: +1 630-766-6869E-mail : [email protected]
20170 South Western AvenueTorrance, CA 90501U.S.A.Phone: +1 310-609-3988Toll Free: 1-800-252-3665Fax: +1 310-609-3916E-mail : [email protected]
Southeast
Southwest
2150 Boggs Road, Suite 100Duluth, GA 30096U.S.A.Phone: +1 770-418-1904Toll Free: 1-800-874-6445Fax: +1 770-418-9403E-mail : [email protected]
8105 N. Beltline RoadSuite 130, Irving, TX 75063U.S.A.Phone: +1 972-929-1515Toll Free: 1-800-295-7886Fax: +1 972-915-0060E-mail : [email protected]
Head office : 19-19 Takanawa 2-chome Minato-ku Tokyo 108-8586, JapanPhone : +81 (0)3-3448-5850Fax : +81 (0)3-3447-7637E-mail : [email protected] : http://www.ikont.co.jp/eg/Plant : Gifu, Kamakura
ASEAN REPRESENTATIVE OFFICELevel 8, #1 Silom Road, SilomBangrak, BangkokThailand 10500Phone: +66 (0)-2-231-8278Fax: +66 (0)-2-231-8121E-mail: [email protected]
The Netherlands
Germany
Sheffieldstraat 35-393047 AN RotterdamThe NetherlandsPhone: +31 (0)10-4626868Fax: +31 (0)10-4626099E-mail : [email protected]
Mündelheimer Weg 5640472 DüsseldorfGermanyPhone: +49 (0)211-414061Fax: +49 (0)211-427693E-mail : [email protected]
Im Gewerbepark D 3093059 RegensburgGermanyPhone: +49 (0)941-206070Fax: +49 (0)941-2060719E-mail : [email protected]
Gruben Str.95c66540 NeunkirchenGermanyPhone: +49 (0)6821-999-860Fax: +49 (0)6821-999-8626E-mail : [email protected]
UK
Spain
France
2 Vincent Avenue, CrownhillMilton Keynes Bucks MK8 0ABUnited KingdomPhone: +44 (0)1908-566144Fax: +44 (0)1908-565458E-mail : [email protected]
Autovia Madrid-Barcelona, Km. 43,700Polig. Ind. AIDA, A-8, Ofic. 2, 119200-Azuqueca de HenaresGuadalajara, SpainPhone: +34 949-263390Fax: +34 949-263113E-mail : [email protected]
Roissypole Le Dôme2 rue de La HayeBP 15950 Tremblay en France95733 Roissy C. D. G. CedexFrancePhone: +33 (0)1-48165739Fax: +33 (0)1-48165746E-mail : [email protected]
IKO INTERNATIONAL, INC.NIPPON THOMPSON CO., LTD.
IKO-THOMPSON (SHANGHAI) LTD.
NIPPON THOMPSON EUROPE B.V.
ISO 9001 & 14001 Quality system registration certificate
Recognizing that conservation of the global environment is the top-priority challenge for the world’ s population, will conduct its activities with consideration of the environment as a corporate social responsibility, reduce its negative impact on the environment, and help foster a rich global environment.
http://www.ikont.com/ http://www.ikont.eu/