ALKALINITY TEST KITMODEL DR-A • CODE 3467
QUANTITY CONTENTS CODE
15 mL *Alkalinity Indicator #1, pH 8.3 *3870-E15 mL Alkalinity Indicator #2, pH 4.5 3869-E60 mL *Alkalinity Titration Reagent B *4493DR-H1 Test Tube, 5-10-15 mL, glass, w/cap 07781 Direct Reading Titrator, 0-200 Range 0382*WARNING: Reagents marked with a * are considered to be potential healthhazards. To view or print a Material Safety Data Sheet (MSDS) for thesereagents see MSDS CD or www.lamotte.com. To obtain a printed copy,contact LaMotte by e-mail, phone or fax.To order a complete set of refill reagents, order as R-3467. To order individualreagents or test kit components, use the specified code number.NOTE: Carefully read the instruction manual for the LaMotte DirectReading Titrator before performing the titration described below. TheTitrator is calibrated in terms of alkalinity expressed as parts per million(ppm) calcium carbonate (CaCO3). Each minor division on the Titratorscale equals 4 ppm CaCO3.
EPA ACCEPTED PROCEDURE
To qualify as an EPA accepted test and to achieve greatest accuracy, thenormality of the *Alkalinity Reagent B should be checked periodically.Standardize *Alkalinity Reagent B by titrating against 0.05N Na2CO3;1 mL = 1.00 mg CaCO3. Should a variance of greater than 0.3 mL of*Alkalinity Reagent B occur, discard and order a fresh bottle of*Alkalinity Reagent B (Code 4493DR-H). A CaCO3 equivalentstandard of 100 ppm is also available (Code 6199-H). Refer to Standard
Methods, 16th edition, 403, 1985.
EPACOMPLIANT
PHENOLPHTHALEIN (P) ALKALINITY PROCEDURE
1. Fill test tube (0778) to 5 mL line with sample water.2 Add two drops of *Alkalinity Indicator # 1 (3870). Cap and mix. If
no red color develops, P alkalinity is zero. If red, proceed to Step 3.3. Fill Direct Reading Titrator with *Alkalinity Reagent B (4493).
Insert Titrator in center hole of test tube cap.4. While gently swirling tube, slowly depress plunger until red color
disappears. Record test result where plunger tip meets titrator scale.Record as P Alkalinity in ppm CaCO3.EXAMPLE: Plunger tip is 3 minor divisions below 80 line. Thetest result is 80 + (3 x 4) = 92 ppm, since each division is equal to4 ppm.
5. If plunger tip reaches the bottom line on the titrator scale (200ppm) before the endpoint color change occurs, refill Titrator andcontinue titration. When recording test result, include originalamount of reagent titrated (200 ppm).NOTE: Do not move the titrator plunger after P Alkalinityendpoint has been obtained.
TOTAL (T) ALKALINITY PROCEDURE
6. Without moving plunger, remove Titrator and test tube cap fromtest tube containing sample from Step 4.
7. Add two drops Alkalinity Indicator #2. Cap and swirl to mix. Ablue color will appear. Insert Titrator in center hole of test tube cap.
8. While gently swirling tube, slowly depress plunger until blue colorchanges to green. Record test result as T Alkalinity in ppm CaCO3.Include total amount of titration reagent added. (See Step 5).
9. If only Total Alkalinity is to be tested, perform Steps 1, 7 and 8only, using a full titrator for Step 8.
CALCULATION OF ALKALINITY RELATIONSHIPS
Results obtained from Phenolphthalein and Total Alkalinitydeterminations offer a means for the stoichiometric classification ofthree principal forms of Alkalinity present in many water supplies.Classification attributes the entire alkalinity to bicarbonate, silica,phosphoric and boric acids. This classification system further assumesincompatilibity of Hydroxide and Bicarbonate Alkalinities in the samesample. Since calculations are on a stoichiometric basis, ionconcentrations in the strictest sense are not represented in the results.According to this scheme:A. Carbonate Alkalinity is present when Phenolphthalein is not zero
but is less than the Total Alkalinity.B. Hydroxide Alkalinity is present if Phenolphthalein Alkalinity is
more than one-half the Total Alkalinity.C. Bicarbonate Alkalinity is present if Phenolphthalein Alkalinity is
less than one-half the Total Alkalinity.Mathematical conversion of the result is shown in the following table:
Relationships Between Phenolphthalein,Total, Carbonate, Bicarbonate and Hydroxide Alkalinity
Result ofTitration
HydroxideAlkalinity as
CaCO3
CarbonateAlkalinity as
CaCO3
BicarbonateAlkalinity as
CaCO3
P = 0 0 0 TP < ½T 0 2P T � 2PP = ½T 0 2P 0P > ½T 2P � T 2(T � P) 0
P = T T 0 0
MATERIAL SAFETY DATA SHEETP.O. Box 329 - 802 Washington Avenue Chestertown, MD 21620 - USATELEPHONE # FOR INFORMATION 410 778-310024 HOUR EMERGENCY NUMBER (CHEM-TEL): USA, Canada, Puerto Rico 800-255-3924;
MSDS
Outside North American Continent 813-248-0585 (call Collect)
1. Product Identification
Alkalinity Indicator pH 4.5
Product Code: 3869Product Description:
Manufactured By: LaMotte Company802 Washington AvenueChestertown, MD 21620
TLVPEL
C 2 mg/cubic m
N/E
%
<0.1
0.1
to 100%
1310-73-2
62625-32-5
7732-18-5
2. Composition/Information On Ingredients
CAS#/Name
Sodium Hydroxide
Bromcresol Green, sodium salt
Water
C 2 mg/cubic m
N/E
Hazard
Yes
Yes
No
3. Hazards Overview
N/A
Primary Route Of Entry: Ingestion
Carcinogenicity: None:
Non-toxic, non-hazardous
Other Health Related Comments:
HMIS HazardScale: 4 = Extreme, 3 = High, 2 = Moderate, 1= Slight, 0 = Least
Health: 0 Flammability: 0 Reactivity: 0
1
3869 Alkalinity Indicator pH 4.5Product Code: Product Description:
4. First Aid Measures
Eye Contact:
Skin Contact:
Inhalation:
Ingestion:
Flush thoroughly with water.
Drink water. Consult physician if symptoms appear.
N/A
Wash with soap and water.
5. Fire Fighting Measures
Extinguishing Media:Special Fire Fighting Procedures:
Flash Point (Method Used): UEL:LEL: N/A N/A
Unusual Fire & Explosion Hazard:
N/A
Not a fire hazard
N/A
N/A
6. Accidental Release Measures
Mop up and flush down drain with excess water.
7. Handling & Storage
Store in cool, dry, place out of direct sunlight.
2
3869 Alkalinity Indicator pH 4.5Product Code: Product Description:
8. Exposure Controls/Personal Protection
Normal
Eye Protection Lab Coat
Ventilation
Protection When Handling
N/AWork/Hygenic Practices:
9. Physical & Chemical Properties
Appearance:Solubility In Water:Odor:pH:
NoneSolubleDark Green Liquid
4.5
Vapor Density: <1 (Air=1)<17 mm Hg @ 20 deg CVapor Pressure:
Boiling Point: ca. 100 degCN/AMelting Point:
10. Stability & Reactivity
Stable: Yes
N/A
N/A
N/AHazardous Decomposition Products:
Incompatibility (Materials To Avoid):
Conditions To Avoid:
11. Toxicological Information
Non-toxic
Target Organs: N/A
3
3869 Alkalinity Indicator pH 4.5Product Code: Product Description:
12. Ecological Information
Information Not Yet Available
13. Disposal ConsiderationsPour down drain with excess water. Dispose according to federal, state and local regulations.
QRLabel5314. Transportation Information
Not Regulated For Transport
15. Regulatory Information
Ingredient--- Canada ---USA
TSCAEurope EC DSL NDSL Australia Japan
Yes Yes1310-73-2Sodium Hydroxide
62625-32-5Bromcresol Green, sodium salt
7732-18-5Distilled Water
Yes No Yes Yes
Yes Yes Yes No No No
YesYes Yes No Yes Yes
Hazard
Yes
Yes
No
Chemical Inventory Status
Federal, State, & International Regulations
Ingredient TPQRQ--------- SARA 313 ---------
Chemical Category--- SARA 302 ---
CERCLARCRA 261.33
TSCA 8(D)
1310-73-2Sodium Hydroxide
62625-32-5Bromcresol Green, sodium salt
7732-18-5Distilled Water
No No
No No
No No
No
1000
No No
No No
No No
No No
Listed
No
No
No
No
No
4
3869 Alkalinity Indicator pH 4.5Product Code: Product Description:
Ingredient
--- SARA 311/312 ---Hazard Categories
-------- Australia -------Hazchem Code
Poison Schedule
1310-73-2Sodium Hydroxide
62625-32-5Bromcresol Green, sodium salt
7732-18-5Distilled Water
S6
None Allocated
None Allocated
Yes
No
Yes 2R
None Allocated
None Allocated
No
No
No
No
No
No
No Yes
No No
No No
Acute Chronic Fire Pressure ReactivityThis MSDS Is WHMIS Compliant
3869No No No No No None Allocated None Allocatedproduct
as a whole
Yes
16. Other Information
Prepared By:8/31/2006Revised:
IP, Regulatory Affairs Department
5
MATERIAL SAFETY DATA SHEETP.O. Box 329 - 802 Washington Avenue Chestertown, MD 21620 - USATELEPHONE # FOR INFORMATION 410 778-310024 HOUR EMERGENCY NUMBER (CHEM-TEL): USA, Canada, Puerto Rico 800-255-3924;
MSDS
Outside North American Continent 813-248-0585 (call Collect)
1. Product Identification
Alkalinity Indicator pH 8.3
Product Code: 3870Product Description:
Manufactured By: LaMotte Company802 Washington AvenueChestertown, MD 21620
TLVPEL
400 ppm
N/E
%
47
0.5
to 100%
67-63-0
77-09-8
7732-18-5
2. Composition/Information On Ingredients
CAS#/Name
2-propanol
Phenolphthalein
Water
980 mg/cubic m
N/E
Hazard
Yes
Yes
No
3. Hazards Overview
Warning! Flammable liquid and vapor. Harmful if swallowed or inhaled. May be irritating to eyes, skin, and respiratory tract. Affects central nervous system.
Primary Route Of Entry: Eye Skin Ingestion Inhalation
Carcinogenicity: Yes: NTP
Warning This product contains phenolphthalein, a chemical known to the state of California to cause cancer.
Other Health Related Comments:
HMIS HazardScale: 4 = Extreme, 3 = High, 2 = Moderate, 1= Slight, 0 = Least
Health: 1 Flammability: 2 Reactivity: 1
1
3870 Alkalinity Indicator pH 8.3Product Code: Product Description:
4. First Aid Measures
Eye Contact:
Skin Contact:
Inhalation:
Ingestion:
Flush with water for 15 minutes. Consult a physician.
Drink large amounts of water. Consult physician immediately.
Remove to fresh air.
Flush with water. Wash with soap and water.
5. Fire Fighting Measures
Extinguishing Media:Special Fire Fighting Procedures:
Flash Point (Method Used): UEL:LEL: 2% 12%
Unusual Fire & Explosion Hazard:
ca. 13 C--closed cup
Dry chemical, CO2, or water spray
N/A
Vapors may flow along floor to ignition source and flash back.
6. Accidental Release Measures
Eliminate all sources of ignition. Absorb on paper. Evaporate on iron pan in hood.
7. Handling & Storage
Store in cool, dry, storage area away from heat, ignition sources, and incompatible materials. Do not use near heat or flame
2
3870 Alkalinity Indicator pH 8.3Product Code: Product Description:
8. Exposure Controls/Personal Protection
Mechanical
Eye Protection Gloves Lab Coat
Ventilation
Protection When Handling
Use with adequate ventilation and avoid contact with skin and eyes.Work/Hygenic Practices:
9. Physical & Chemical Properties
Appearance:Solubility In Water:Odor:pH:
AlcoholSolubleClear Colorless Liquid
N/A
Vapor Density: >1 (Air=1)ca. 30 mm Hg @ 20 CVapor Pressure:
Boiling Point: <100 deg CN/AMelting Point:
10. Stability & Reactivity
Stable: Yes
Heat, sources of ignition
Contact with nitric acid or other strong oxidizers
COxHazardous Decomposition Products:
Incompatibility (Materials To Avoid):
Conditions To Avoid:
11. Toxicological Information
oral rat LD50: 5840 mg/kg; oral human LD50: 3570 mg/kg for 2-propanol. Investigated as a tumorigen, mutagen, reproductive effector.
Target Organs: Central Nervous System Eyes Lung Skin
3
3870 Alkalinity Indicator pH 8.3Product Code: Product Description:
12. Ecological Information
When released to water or soil, isopropanol is expected to quickly evaporate.Not expected to significantly bioaccumulate.When released into the air, it is expected to be readily degraded or to be removed to a degree by wet deposition (rain,snow)
13. Disposal ConsiderationsSmall quantity: Flush down drain with excess water. Large quantity: Atomize into an incinerator. Dispose according to federal, state and local regulations.
14. Transportation Information
Proper Shipping Name:ISOPROPANOLDOT:
IATA: ISOPROPANOL
Hazard Class/Div:33IATA:
DOT:
UN: 1219
IIPacking Group:
15. Regulatory Information
Ingredient--- Canada ---USA
TSCAEurope EC DSL NDSL Australia Japan
Yes Yes67-63-0Isopropyl Alcohol
77-09-8Phenolphthalein
7732-18-5Distilled Water
Yes No Yes Yes
Yes Yes Yes No Yes Yes
YesYes Yes No Yes Yes
Hazard
Yes
Yes
No
Chemical Inventory Status
4
3870 Alkalinity Indicator pH 8.3Product Code: Product Description:
Federal, State, & International Regulations
Ingredient TPQRQ--------- SARA 313 ---------
Chemical Category--- SARA 302 ---
CERCLARCRA 261.33
TSCA 8(D)
67-63-0Isopropyl Alcohol
77-09-8Phenolphthalein
7732-18-5Distilled Water
No No
No No
No No
No
No
No No
No No
No No
No No
Listed
Yes
No
No
No
No
5
3870 Alkalinity Indicator pH 8.3Product Code: Product Description:
Ingredient
--- SARA 311/312 ---Hazard Categories
-------- Australia -------Hazchem Code
Poison Schedule
67-63-0Isopropyl Alcohol
77-09-8Phenolphthalein
7732-18-5Distilled Water
None Allocated
None Allocated
None Allocated
Yes
No
Yes 2[S]2
None Allocated
None Allocated
Yes
Yes
No
Yes
No
No
No No
No No
No No
Acute Chronic Fire Pressure ReactivityThis MSDS Is WHMIS Compliant
3870 Yes Yes Yes No No 2[S]2 None Allocatedproductas a whole
Yes
16. Other Information
Prepared By:12/2/2005Revised:
IP, Regulatory Affairs Department
6
MATERIAL SAFETY DATA SHEETP.O. Box 329 - 802 Washington Avenue Chestertown, MD 21620 - USATELEPHONE # FOR INFORMATION 410 778-310024 HOUR EMERGENCY NUMBER (CHEM-TEL): USA, Canada, Puerto Rico 800-255-3924;
MSDS
Outside North American Continent 813-248-0585 (call Collect)
1. Product Identification
Sodium Hydroxide, 1.0 N
Product Code: 4004Product Description:
Manufactured By: LaMotte Company802 Washington AvenueChestertown, MD 21620
TLVPEL
C 2 mg/cubic m
%
4
to 100%
1310-73-2
7732-18-5
2. Composition/Information On Ingredients
CAS#/Name
Sodium Hydroxide
Water
C 2 mg/cubic m
Hazard
Yes
No
3. Hazards Overview
Warning! Corrosive. Can cause severe irritation or burns to all body tissue. Harmful if swallowed.
Primary Route Of Entry: Skin Ingestion
Carcinogenicity: None:
Other Health Related Comments:
HMIS HazardScale: 4 = Extreme, 3 = High, 2 = Moderate, 1= Slight, 0 = Least
Health: 2 Flammability: 0 Reactivity: 1
1
4004 Sodium Hydroxide, 1.0 NProduct Code: Product Description:
4. First Aid Measures
Eye Contact:
Skin Contact:
Inhalation:
Ingestion:
Immediately flush with water for 15 minutes. Consult a physician.
Do not induce vomiting. Rinse out mouth. Drink plenty of water. Call a doctor immediately.
N/A
Immediately flush with water for 15 minutes. Remove affected clothing and rinse skin thoroughly.
5. Fire Fighting Measures
Extinguishing Media:Special Fire Fighting Procedures:
Flash Point (Method Used): UEL:LEL: N/A N/A
Unusual Fire & Explosion Hazard:
N/A
Not a fire hazard
N/A
N/A
6. Accidental Release Measures
Wear gloves and eye protection. Carefully neutralize with vinegar or other dilute acid (6 M HCl). Mop up and flush to drain with excess water.
7. Handling & Storage
Store in cool, dry, storage area away from acids and other incompatible materials.
2
4004 Sodium Hydroxide, 1.0 NProduct Code: Product Description:
8. Exposure Controls/Personal Protection
Normal
Eye Protection Gloves Lab Coat
Ventilation
Protection When Handling
Avoid contact with eyes, skin and clothing. Wash after handling.Work/Hygenic Practices:
9. Physical & Chemical Properties
Appearance:Solubility In Water:Odor:pH:
NoneSolubleClear Colorless Liquid
14
Vapor Density: <1 (Air=1)<17 mm Hg @ 20 deg CVapor Pressure:
Boiling Point: 102 deg C (5% soln)(-) 4 deg C (5% soln)Melting Point:
10. Stability & Reactivity
Stable: Yes
N/A
Strong acids, metals
N/AHazardous Decomposition Products:
Incompatibility (Materials To Avoid):
Conditions To Avoid:
11. Toxicological Information
Sodium hydroxide investigated as a tumorigen, mutagen.
Target Organs: Corrosive to all body parts Skin
3
4004 Sodium Hydroxide, 1.0 NProduct Code: Product Description:
12. Ecological Information
Information Not Yet Available
13. Disposal ConsiderationsNeutralize and flush down drain with excess water. Dispose according to federal, state and local regulations.
14. Transportation Information
Proper Shipping Name:SODIUM HYDROXIDE SOLUTIONDOT:
IATA: SODIUM HYDROXIDE SOLUTION
Hazard Class/Div:
88
IATA:DOT:
UN: 1824
IIPacking Group:
15. Regulatory Information
Ingredient--- Canada ---USA
TSCAEurope EC DSL NDSL Australia Japan
Yes Yes1310-73-2Sodium Hydroxide
7732-18-5Distilled Water
Yes No Yes Yes
Yes Yes Yes No Yes Yes
Hazard
Yes
No
Chemical Inventory Status
Federal, State, & International Regulations
Ingredient TPQRQ--------- SARA 313 ---------
Chemical Category--- SARA 302 ---
CERCLARCRA 261.33
TSCA 8(D)
1310-73-2Sodium Hydroxide
7732-18-5Distilled Water
No No
No No No
1000 No No
No No
Listed
No
No
No
No
4
4004 Sodium Hydroxide, 1.0 NProduct Code: Product Description:
Ingredient
--- SARA 311/312 ---Hazard Categories
-------- Australia -------Hazchem Code
Poison Schedule
1310-73-2Sodium Hydroxide
7732-18-5Distilled Water
S6
None AllocatedNo
Yes 2R
None Allocated
No
No
No
No
No Yes
No No
Acute Chronic Fire Pressure ReactivityThis MSDS Is WHMIS Compliant
4004Yes No No No No 2R S5product
as a whole
Yes
16. Other Information
Prepared By:6/12/2006Revised:
IP, Regulatory Affairs Department
5
MATERIAL SAFETY DATA SHEETP.O. Box 329 - 802 Washington Avenue Chestertown, MD 21620 - USATELEPHONE # FOR INFORMATION 410 778-310024 HOUR EMERGENCY NUMBER (CHEM-TEL): USA, Canada, Puerto Rico 800-255-3924;
MSDS
Outside North American Continent 813-248-0585 (call Collect)
1. Product Identification
Alkalinity Titration Reagent
Product Code: 4015Product Description:
Manufactured By: LaMotte Company802 Washington AvenueChestertown, MD 21620
TLVPEL
1 mg/cubic m
%
0.1
to 100%
7664-93-9
7732-18-5
2. Composition/Information On Ingredients
CAS#/Name
Sulfuric Acid
Water
1 mg/cubic m
Hazard
Yes
No
3. Hazards Overview
May irritate eyes and skin.
Primary Route Of Entry: Skin
Carcinogenicity: None:
Non-toxic
Other Health Related Comments:
HMIS HazardScale: 4 = Extreme, 3 = High, 2 = Moderate, 1= Slight, 0 = Least
Health: 1 Flammability: 0 Reactivity: 0
1
4015 Alkalinity Titration ReagentProduct Code: Product Description:
4. First Aid Measures
Eye Contact:
Skin Contact:
Inhalation:
Ingestion:
Flush thoroughly with water for 15 minutes. Consult a physician if irritation develops.
Rinse out mouth. Drink 1 - 2 glasses of water. Consult physician if symptoms appear.
N/A
Flush with water. Remove affected clothing and wash skin with soap and water.
5. Fire Fighting Measures
Extinguishing Media:Special Fire Fighting Procedures:
Flash Point (Method Used): UEL:LEL: N/A N/A
Unusual Fire & Explosion Hazard:
N/A
Not a fire hazard
N/A
N/A
6. Accidental Release Measures
Cover spill with sodium bicarbonate. Scoop up slurry and wash down drain with excess water.
7. Handling & Storage
Store in cool, dry, place.
2
4015 Alkalinity Titration ReagentProduct Code: Product Description:
8. Exposure Controls/Personal Protection
Normal
Eye Protection Gloves Lab Coat
Ventilation
Protection When Handling
Avoid contact with eyes and skin. Wash after handling.Work/Hygenic Practices:
9. Physical & Chemical Properties
Appearance:Solubility In Water:Odor:pH:
NoneSolubleClear Colorless Liquid
2
Vapor Density: <1(Air=1)<17 mm Hg @ 20 deg CVapor Pressure:
Boiling Point: ca. 100 deg CN/AMelting Point:
10. Stability & Reactivity
Stable: Yes
N/A
N/A
Sulfur OxidesHazardous Decomposition Products:
Incompatibility (Materials To Avoid):
Conditions To Avoid:
11. Toxicological Information
Oral rat LD50: 2140 mg/kg for sulfuric acid, concentrated. Product 4015 may be irritating to stomach if much is swallfowed because pH is slightly acidic.
Target Organs: Skin
3
4015 Alkalinity Titration ReagentProduct Code: Product Description:
12. Ecological Information
Information Not Yet Available
13. Disposal ConsiderationsAdd slowly to a solution of sodium bicarbonate or sodium carbonate. Pour neutralized solution down drain with excess water. Dispose according to federal, state and local regulations.
QRLabel5314. Transportation Information
Not Regulated For Transport
15. Regulatory Information
Ingredient--- Canada ---USA
TSCAEurope EC DSL NDSL Australia Japan
Yes Yes7664-93-9Sulfuric Acid
7732-18-5Distilled Water
Yes No Yes Yes
Yes Yes Yes No Yes Yes
Hazard
Yes
No
Chemical Inventory Status
Federal, State, & International Regulations
Ingredient TPQRQ--------- SARA 313 ---------
Chemical Category--- SARA 302 ---
CERCLARCRA 261.33
TSCA 8(D)
7664-93-9Sulfuric Acid
7732-18-5Distilled Water
1000 1000
No No No
1000 No No
No No
Listed
Yes
No
No
No
4
4015 Alkalinity Titration ReagentProduct Code: Product Description:
Ingredient
--- SARA 311/312 ---Hazard Categories
-------- Australia -------Hazchem Code
Poison Schedule
7664-93-9Sulfuric Acid
7732-18-5Distilled Water
None Allocated
None AllocatedNo
Yes 2P
None Allocated
Yes
No
No
No
No Yes
No No
Acute Chronic Fire Pressure ReactivityThis MSDS Is WHMIS Compliant
4015No No No No No None Allocated None Allocatedproduct
as a whole
Yes
16. Other Information
Prepared By:6/26/2007Revised:
IP, Regulatory Affairs Department
5
MATERIAL SAFETY DATA SHEETP.O. Box 329 - 802 Washington Avenue Chestertown, MD 21620 - USATELEPHONE # FOR INFORMATION 410 778-310024 HOUR EMERGENCY NUMBER (CHEM-TEL): USA, Canada, Puerto Rico 800-255-3924;
MSDS
Outside North American Continent 813-248-0585 (call Collect)
1. Product Identification
Alkalinity Titration Reagent B
Product Code: 4493Product Description:
Manufactured By: LaMotte Company802 Washington AvenueChestertown, MD 21620
TLVPEL
1 mg/cubic m
%
0.1
to 100%
7664-93-9
7732-18-5
2. Composition/Information On Ingredients
CAS#/Name
Sulfuric Acid
Water
1 mg/cubic m
Hazard
Yes
No
3. Hazards Overview
May be irritating to skin. May be harmful if swallowed.
Primary Route Of Entry: Ingestion Skin
Carcinogenicity: None
Other Health Related Comments:
HMIS HazardScale: 4 = Extreme, 3 = High, 2 = Moderate, 1= Slight, 0 = Least
Health: 1 Flammability: 0 Reactivity: 0
1
4493 Alkalinity Titration Reagent BProduct Code: Product Description:
4. First Aid Measures
Eye Contact:
Skin Contact:
Inhalation:
Ingestion:
Flush thoroughly with water for 15 minutes. Consult a physician if irritation develops.
Rinse mouth, drink glass of water and consult physician if symptoms appear.
Remove to fresh air.
Flush with water. Remove affected clothing and wash skin with soap and water.
5. Fire Fighting Measures
Extinguishing Media:Special Fire Fighting Procedures:
Flash Point (Method Used): UEL:LEL: N/A N/A
Unusual Fire & Explosion Hazard:
N/A
Not a fire hazard
N/A
N/A
6. Accidental Release Measures
Cover spill with sodium bicarbonate. Scoop up slurry and wash down drain with excess water.
7. Handling & Storage
Store in cool, dry, storage area..
2
4493 Alkalinity Titration Reagent BProduct Code: Product Description:
8. Exposure Controls/Personal Protection
Normal
Gloves Eye Protection Lab Coat
Ventilation
Protection When Handling
Avoid contact with eyes, skin and clothing.Work/Hygenic Practices:
9. Physical & Chemical Properties
Appearance:Solubility In Water:Odor:pH:
NoneSolubleClear Colorless Liquid
2
Vapor Density: <1 (Air=1)<17 mm @ 20 deg CVapor Pressure:
Boiling Point: ca. 100 deg CN/AMelting Point:
10. Stability & Reactivity
Stable: Yes
N/A
N/A
SOxHazardous Decomposition Products:
Incompatibility (Materials To Avoid):
Conditions To Avoid:
11. Toxicological Information
Oral rat LD50: 2140 mg/kg for sulfuric acid concentrated. Product #4493 is non-toxic but may be irritating to skin or cause GI distress if swallowed because of its sllght acidity (pH2).
Target Organs: Skin
3
4493 Alkalinity Titration Reagent BProduct Code: Product Description:
12. Ecological Information
Information Not Yet Available
13. Disposal ConsiderationsAdd slowly to a solution of sodium carbonate & calcium hydroxide. Pour this neutralized solution down drain with excess water. Dispose according to federal, state and local regulations.
QRLabel5314. Transportation Information
Not Regulated For Transport
15. Regulatory Information
Ingredient--- Canada ---USA
TSCAEurope EC DSL NDSL Australia Japan
Yes Yes7664-93-9Sulfuric Acid
7732-18-5Distilled Water
Yes No Yes Yes
Yes Yes Yes No Yes Yes
Hazard
Yes
No
Chemical Inventory Status
Federal, State, & International Regulations
Ingredient TPQRQ--------- SARA 313 ---------
Chemical Category--- SARA 302 ---
CERCLARCRA 261.33
TSCA 8(D)
7664-93-9Sulfuric Acid
7732-18-5Distilled Water
1000 1000
No No No
1000 No No
No No
Listed
Yes
No
No
No
4
4493 Alkalinity Titration Reagent BProduct Code: Product Description:
Ingredient
--- SARA 311/312 ---Hazard Categories
-------- Australia -------Hazchem Code
Poison Schedule
7664-93-9Sulfuric Acid
7732-18-5Distilled Water
None Allocated
None AllocatedNo
Yes 2P
None Allocated
Yes
No
No
No
No Yes
No No
Acute Chronic Fire Pressure ReactivityThis MSDS Is WHMIS Compliant
4493 Yes No No No No None Allocated None Allocatedproductas a whole
Yes
16. Other Information
Prepared By:11/10/2005Revised:
IP, Regulatory Affairs Department
5