HD-PLC compatiblePLC Adaptor
DA-PU100
Connect your facilities to the network easily!
Multi-hop PLC Adaptor
No need to install an exclusive line.
All you need is a power line for high-speed data communication.
Multi-hopping supports long-distance transmission even in a large factory or building.
Build a high-speed
network using your power line
In addition to Ethernet interface, RS-485 and USB interfaces are provided as standard.
The ability to connect legacy devices often found in workshops expands the scope of applications.
IP5X dust protected.
Ensures safe, reliable use even in a dusty environment in a factory/building or in a location where maintenance is not available for long periods.
Dustprooffor enhanced
reliability
Variety ofinterfaces
MG-PLC002EN 1807UAW/FP-M1
HD-PLCMulti-hop
• The color of the actual product may differ from that shown in this lea�et. • The design and speci�cations of the product are subject to change without prior notice. • The actual product may bear the operating cautions plate on the body.
Router/Internet
Master
RS-485 master device*12
EthernetEthernet
RS-485RS-485
EthernetEthernet
Power LinePower Line
Relay
TerminalDistribution board
Relay
Terminal Terminal Computer
Environment sensor
Data logger*12
Security camera
Relay
TerminalDistribution board
USBUSB
Terminal
EthernetEthernet
Terminal
RS-485RS-485
Terminal
• Communication may be delayed or become unavailable under certain operating environments. The distance and rate of communication vary depending on the connected devices and operating environment.
• Panasonic is not responsible for any loss of data and other direct or indirect damage caused by external factors such as power failures or noise on electrical wiring.
• This product is set as a “terminal” when shipped. When setting up a network using several of these products, one of them must be designated as the “master” using the specified software tool before use.
*1: The indicated value is the theoretical maximum. Actual speeds will be less than this value.*2: This value may differ based on the operating environment.*3: The maximum number of terminal adaptors may vary depending on the operating environment.*4: The recommended number when using a switching hub.*5: The communication distance and communication speed may vary depending on the connected devices and operating environment. Also, this product does not support high speed data transfer.*6: Web cameras, USB speakers, or other USB devices that use isochronous forwarding for real-time operation cannot be used with this product. Other USB devices might also not be usable depending on their driver specifications.*7: The number of devices that can be connected depends on the usage environment and the type of device.*8: The communication distance and communication speed may vary depending on the connected devices and operating environment. *9: This product uses the "Store and Forward" method, in which it accumulates commands/ responses and then forwards them. Therefore, some forwarding delay will occur.*10: The master/slave setting for RS-485 is separate from the MASTER/TERMINAL setting for PLC.*11: Shielded twisted-pair wiring is recommended.
Multi-hop technology is a type of communication in which multiple nodes or relays are used to expand the coverage area, facilitating transmission between terminals at greater distances. It is an applied technology of the CMSR (Centralized Metric-based Source Routing) adopted in the international standard ITU-T G.9905.
Operating Cautions
Unit
Operating environmentTemperature: -25°C – 60°C (-13°F – 140°F) Humidity: 20 % RH – 85 % RH (No condensation)
Degree of protection from solid objects IP5X
External dimensions (W x H x D)
Approx. 75mm × 102mm × 47mm (2.95 in. × 4.02 in. × 1.85 in.) (Unit only. Not including protrusions.)
Weight Approx. 260 g (0.57 lb.) (Unit only)
Interface PLC x 1, Ethernet x 1, RS-485 x 1, USB x 1
Power requirements AC120V - 240V, 50Hz/60Hz
Power consumption Avg. 4 W, Max. 7 W (100 V) Avg. 6 W, Max. 8.5 W (240 V)
PLC Port
Example of multi-hop configuration
Standard HD-PLC Multi-hop
Multi-hop 10
Communication speed 240 Mbps*1
Frequency band 2 MHz - 28 MHz
Modulation method Wavelet OFDM (2 PAM - 32 PAM)
Security AES 128-bit encryption
Communication distance Approx. 200 m (656 ft)*2 between PLC adaptors
Number of terminal adaptors Max. 1,024 units*3 per 1 MASTER unit
Ethernet Port
Physical interface IEEE 802.3 (10BASE-T) / IEEE 802.3u (100BASE-TX) / Auto MDI/MDI-X / Auto Negotiation
Protocol TCP/IP (IPv4 / IPv6)
Access method CSMA/CD
Number of connectable devices Max. 8 devices per MASTER or TERMINAL adaptor*4
USB Port
Interface USB 2.0 / USB 1.1 (Type-A)*5
Forwarding method Control forwarding, bulk forwarding, interrupt forwarding.*6
Number of connectable devices*7
Max. 5 devices per 1 adaptor (including hubs). The number of connected devices that can be used on 1 PC is 64 devices.
RS-485 Port
Standard EIA-485
Connection method Half-duplex
Max. cable length Max. 1,200 m (approx. 4,000 ft)*8
Communication speed300 / 600 / 1,200 / 2,400 / 4,800 / 9,600 / 19,200 / 38,400 / 57,600 / 115,200 / 230,400 / 250,000 / 460,800 / 921,600 bps*8
Response time The time "Command/Response communication time*9" with "About 10 ms per hop" added.
Number of connectable devices Max. 31 slave units*10 per MASTER unit
Supported protocols Non procedural
Applicable AWG wire size AWG28 – AWG16*11
compatible PLC Adaptor DA-PU100HD-PLC: Name of the high-speed power line communication system proposed by Panasonic. HD-PLC is a registered trademark or trademark of Panasonic Corporation in Japan and in other countries. “HD-PLC” stands for “High De�nition Power Line Communication”.
*12: RS-485 communication is available only between devices connected to RS-485 ports.