POLYBASE R+ S 3 in 1 prefabricated panel
Advantageous thermal value*For cold applied or SBS bitumen systemFlamelessVOC freeQuick and easy installationIncreases productivity on jobsite
value of panel according to specificationsMonolithic panel
ADVANTAGES ACKNOWLEDGMENT
T. 450.477.4423 1.800.363.2307 FRANSYL.COM
*The use of a 9’’ wide S/S type tape or self-adhesiveunderface and sanded surface tape is mandatory.
Note: If used with a self-adhesive tape, Lexcor MULTIGRIP Primeris required and the panel must be covered with a cap sheetwithin the same day.
THICKNESS OF POLYBASE R+ SType HR (Type I) Type THR (Type II)
R-11.5 3’’ 2 3/4’’
R-13.5 3 1/2’’ 3 1/4’’’
R-14.5 3 3/4’’ 3 1/2’’
R-15.5 4’’ 3 3/4’’
R-17.5 4 1/2’’ 4 1/4’’
R-19.5 5’’ 4 3/4’’
«R» Insulating Value
POLYBASE R+ S
26418
The thermal value of the expanded polystyrene is 100% guaranteed
1 1/2’’ overlapping protection strip *
95 g underlayment membrane of 2.2 mm thick,consisting of a fiberglass reinforcement with athermofusible underface and a sanded surface OR180 g underlayment membrane of 2.2 mm thick,consisting of a polyester reinforcement with athermofusible underface and a sanded surface
double-sided 3" self-adhesive overlapping strip
1/2" (12.70 mm) composite panel, factory lamina-ted on both faces of a fireproof fibreglass sheet
Fransyl Izolon Insulation
Meets Novoclimat requirements
½" (12.70 MM) COMPOSITE PANEL, FACTORY LAMINATED ON BOTH FACES OF A FIRE RETARDANT FIBREGLASS SHEET
Thermal resistance R-2.5(ASTM C518 C177), (RSI-0.53)
Water vapor permeability < 1.00 perm(ASTM E96) (85 ng/Pa s m2)
Compressive strength(ASTM D 1621) 620 kPa10% deformation (90 lbs / in²)
Tensile strength > 35 kPa(ASTM D 1623) (5.07 lbs / in2)
Water absorption < 1%,(ASTM C 209, ASTM D 2842) < 3,5%
Density 2 lbs / ft3
(ASTME D 1622) (32.04 kg/m3)
Smoke developement 50-170(ASTM E84), evaluation on a 10 min. period
Flame spread 40-60(ASTM E84), evaluation on a 10 min. period
POLYBASE R+ SSPECIFICATIONSDIMENSIONS
ROOFING SYSTEMS
T. 450.477.4423 1.800.363.2307 FRANSYL.COM
Cold bending in lower temperatures (ASTM D6163) Successful, °C (°F)
Longitudinal and transversal tensile strength at breakage (ASTM D6163) Successful, kN/m (lbf/in)
Elongation at breakage Successful, N (lbf)
Longitudinal and transversal elongation at breakage (ASTM D6163) Successful %
Longitudinal and transversal tear strength (ONGC-37.56-M) Successful, N (lbf)
Longitudinal and transversal resistance to lap joint (ONGC-37.56-M), 5J @ 23°C Successful, kN/m (lbf/in)
Width x length: 36’’ x 96’’ (914 mm x 2438 mm)
Thickness of shiplap edge*: 2’’ to 4 1/2’’ (51 mm to 114 mm)
Shiplap: 5/8’’ (16 mm)*1Dimensions may vary ± 2% *2Other dimensions available upon request
95 G MEMBRANE OF 2.2 MM THICK, CONSISTING OFA FIBERGLASS REINFORCEMENT WITH A THERMOFUSIBLEUNDERFACE AND SANDED SURFACE, INCLUDING ADOUBLE-SIDED 3’’ SELF-ADHESIVE OVERLAPPING STRIP
180 G MEMBRANE OF 2.2 MM THICK, CONSISTING OFA POLYESTER REINFORCEMENT WITH A THERMOFUSIBLEUNDERFACE AND SANDED SURFACE, INCLUDING ADOUBLE-SIDED 3’’ SELF-ADHESIVE OVERLAPPING STRIP
OR
Installation:
Option 1: Mechanical fastening
Option 2: Adhesive application(Contact your sales rep. for all details)
for 1/2’’ (12.70 mm) thickness
Polybase R+ S Panel with Cap Sheet :UL Class C Fully Adhered (ref. TGFUC.R16778)CAN/ULC-S107
POLYBASE R+ SHR
(Type I)
Thermal resistance R-3.7(ASTM C518 C177) (RSI-0.65)1’’ (25 mm) thickness
Water vapour permability 5.25 perm(ASTM E96), 1’’ (25 mm) thickness (300 ng/Pa·s·m²)
Compressive strength 80 kPa(ASTM D1621) (11.64 lbs/in²)1 ½ ’’ (38 mm) thickness
Flexural strength 170 kPa(ASTM C 203) (24.78 lbs/in²)1 ½ ’’ (38 mm) thickness
Water absorption (ASTM D 2842) 6%1 ½ ’’ (38 mm) thickness
Density 1 lb/ft³(ASTM D 1621) (16.01 kg/m³)
Limiting Oxygen Index 24%(ULC S-701) % minimum
1.5%Dimensional stability (ASTM D 2126)% maximum linear change
THR(Type II)
R-4(RSI-0.7)
3.5 perm(200 ng/Pa·s·m²)
120 kPa(17.46 lbs/in²)
240 kPa(34.97 lbs/in²)
4%
1.25 lb/ft³(20.01 kg/m³)
24%
1.5%
HD(Type II)
R-4,17(RSI-0.73)
2.25 perm(130 ng/Pa·s·m²)
160 kPa(23.3 lbs/in²)
300 kPa(43.71 lbs/in²)
3%
1.5 lb/ft³(24.02 kg/m³)
24%
1.5%
THD(Type III)
R-4,2(RSI-0.74)
2.25 perm(130 ng/Pa·s·m²)
210 kPa(30.6 lbs/in²)
300 kPa(43.71 lbs/in²)
2%
2 lb/ft³(32.03 kg/m³)
24%
1.5%
Important note: It is possible that blisters are formed in the membrane when the temperature increases; this has no impact on the performance and adhesion of the membrane on the panel. Blisters under the mem-brane will fade upon cooling of the panel.
