![Page 1: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/1.jpg)
www.ti.com
PRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.
Copyright © 1996-2004, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Out D
–In D
+In D
V–
+In C
–In C
Out C
Out A
–In A
+In A
V+
+In B
–In B
Out B
OPA4234
SO-14
A D
B C
Low-Power, PrecisionSINGLE-SUPPLY OPERATIONAL AMPLIFIERS
FEATURES WIDE SUPPLY RANGE:
Single Supply: VS = +2.7V to +36VDual Supply: VS = ±1.35V to ±18V
SPECIFIED PERFORMANCE:+2.7V, +5V, and ±15V
LOW QUIESCENT CURRENT: 250µA/amp
LOW INPUT BIAS CURRENT: 25nA max
LOW OFFSET VOLTAGE: 100µV max
HIGH CMRR, PSRR, and AOL
SINGLE, DUAL, and QUAD VERSIONS
DESCRIPTIONThe OPA234 series low-cost op amps are ideal forsingle-supply, low-voltage, low-power applications. Theseries provides lower quiescent current than older“1013”-type products and comes in current industry-standard packages and pinouts. The combination oflow offset voltage, high common-mode rejection, highpower-supply rejection, and a wide supply range pro-vides excellent accuracy and versatility. Single, dual,and quad versions have identical specifications formaximum design flexibility. These general-purpose opamps are ideal for portable and battery-powered appli-cations.The OPA234 series op amps operate from either singleor dual supplies. In single-supply operation, the inputcommon-mode range extends below ground and theoutput can swing to within 50mV of ground. Excellentphase margin makes the OPA234 series ideal for de-manding applications, including high load capacitance.Dual and quad designs feature completely indepen-dent circuitry for lowest crosstalk and freedom frominteraction.
Single version packages are in an SO-8 surface-mountand a space-saving MSOP-8 surface-mount. Dual pack-ages are in an SO-8 surface-mount. Quad packagesare in an SO-14 surface-mount. All are specified for–40°C to +85°C operation.
1
2
3
4
8
7
6
5
V+
Out B
–In B
+In B
Out A
–In A
+In A
V–
OPA2234
SO-8
A
B
1
2
3
4
8
7
6
5
NC
V+
Output
Offset Trim
Offset Trim
–In
+In
V–
OPA234
SO-8, MSOP-8
OPA234 OPA2234OPA234
OPA4234
OPA234OPA2234OPA4234
SBOS055A – MAY 1996 – REVISED JUNE 2004
![Page 2: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/2.jpg)
OPA234, OPA2234, OPA42342SBOS055Awww.ti.com
ELECTRICAL CHARACTERISTICS: VS = +5VAt TA = 25°C, VS = +5V, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
OPA234U, EOPA2234U
OPA234UA, EAOPA2234UA
OPA4234UA, U
PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS
OFFSET VOLTAGEInput Offset Voltage VOS VCM = 2.5V ±40 ±100 ±250 µV
OPA234E, EA ±100 ±150 ±350 µVvs Temperature(1) dVOS/dT Operating Temperature Range ±0.5 ±3 µV/°Cvs Power Supply PSRR VS = +2.7V to +30V, VCM = 1.7V 3 10 20 µV/Vvs Time 0.2 µV/mo
Channel Separation (Dual, Quad) 0.3 µV/V
INPUT BIAS CURRENTInput Bias Current(2) IB VCM = 2.5V –15 –30 –50 nAInput Offset Current IOS VCM = 2.5V ±1 ±5 nA
NOISE f = 1kHzInput Voltage Noise Density vn 25 nV/√HzCurrent Noise Density in 80 fA/√Hz
INPUT VOLTAGE RANGECommon-Mode Voltage Range –0.1 (V+) –1 VCommon-Mode Rejection CMRR VCM = –0.1V to 4V 91 106 86 dB
INPUT IMPEDANCEDifferential 107 || 5 Ω || pFCommon-Mode VCM = 2.5V 1010 || 6 Ω || pF
OPEN-LOOP GAIN VO = 0.25V to 4VOpen-Loop Voltage Gain AOL RL = 10kΩ 108 120 100 dB
RL = 2kΩ 86 96œ86 dB
FREQUENCY RESPONSEGain-Bandwidth Product GBW CL = 100pF 0.35 MHzSlew Rate SR 0.2 V/µsSettling Time: 0.1% G = 1, 3V Step, CL = 100pF 15 µs
0.01% G = 1, 3V Step, CL = 100pF 25 µsOverload Recovery Time (VIN) (Gain) = VS 16 µs
OUTPUTVoltage Output: Positive RL = 10kΩ to VS/2 (V+) –1 (V+) –0.65 V
Negative RL = 10kΩ to VS/2 0.25 0.05 VPositive RL = 10kΩ to Ground (V+) –1 (V+) –0.65 VNegative RL = 10kΩ to Ground 0.1 0.05 V
Short-Circuit Current ISC ±11 mACapacitive Load Drive (Stable Operation)(3) G = +1 1000 pF
POWER SUPPLYSpecified Operating Voltage +5 VOperating Voltage Range +2.7 +36 VQuiescent Current (per amplifier) IQ IO = 0 250 300 µA
TEMPERATURE RANGESpecified Range –40 +85 °COperating Range –40 +125 °CStorage –55 +125 °CThermal Resistance θJA
8-Pin DIP 100 °C/WSO-8 Surface-Mount 150 °C/WMSOP-8 Surface-Mount 220 °C/W14-Pin DIP 80 °C/WSO-14 Surface-Mount 110 °C/W
Specifications same as OPA234U, E.
NOTES: (1) Wafer-level tested to 95% confidence level. (2) Positive conventional current flows into the input terminals. (3) See Small-Signal Overshoot vs LoadCapacitance typical curve.
![Page 3: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/3.jpg)
OPA234, OPA2234, OPA4234 3SBOS055A www.ti.com
ELECTRICAL CHARACTERISTICS: VS = +2.7VAt TA = 25°C, VS = +2.7V, RL = 10kΩ connected to VS/2, and VOUT = VS/2, unless otherwise noted.
OPA234U, EOPA2234U
OPA234UA, EAOPA2234UA
OPA4234UA, U
PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS
OFFSET VOLTAGEInput Offset Voltage VOS VCM = 1.35V ±40 ±100 ±250 µV
OPA234E, EA ±100 ±150 ±350 µVvs Temperature(1) dVOS/dT Operating Temperature Range ±0.5 ±3 µV/°Cvs Power Supply PSRR VS = +2.7V to +30V, VCM = 1.7V 3 10 20 µV/Vvs Time 0.2 µV/mo
Channel Separation (Dual, Quad) 0.3 µV/V
INPUT BIAS CURRENTInput Bias Current(2) IB VCM = 1.35V –15 –30 –50 nAInput Offset Current IOS VCM = 1.35V ±1 ±5 n
NOISE f = 1kHzInput Voltage Noise Density vn 25 nV/√HzCurrent Noise Density in 80 fA/√Hz
INPUT VOLTAGE RANGECommon-Mode Voltage Range –0.1 (V+) –1 VCommon-Mode Rejection CMRR VCM = –0.1V to 1.7V 91 106 86 dB
INPUT IMPEDANCEDifferential 107 || 5 Ω || pFCommon-Mode VCM = 1.35V 1010 || 6 Ω || pF
OPEN-LOOP GAIN VO = 0.25V to 1.7VOpen-Loop Voltage Gain AOL RL = 10kΩ 108 125 100 dB
RL = 2kΩ 86 96 86 dB
FREQUENCY RESPONSEGain-Bandwidth Product GBW CL = 100pF 0.35 MHzSlew Rate SR 0.2 V/µsSettling Time: 0.1% G = 1, 1V Step, CL = 100pF 6 µs
0.01% G = 1, 1V Step, CL = 100pF 16 µsOverload Recovery Time (VIN) (Gain) = VS 8 µs
OUTPUTVoltage Output: Positive RL = 10kΩ to VS/2 (V+) –1 (V+) –0.6 V
Negative RL = 10kΩ to VS/2 0.25 0.05 VPositive RL = 10kΩ to Ground (V+) –1 (V+) –0.65 VNegative RL = 10kΩ to Ground 0.1 0.05 V
Short-Circuit Current ISC ±8 mACapacitive Load Drive (Stable Operation)(3) G = +1 1000 pF
POWER SUPPLYSpecified Operating Voltage +2.7 VOperating Voltage Range +2.7 +36 VQuiescent Current (per amplifier) IQ IO = 0 250 300 µA
TEMPERATURE RANGESpecified Range –40 +85 °COperating Range –40 +125 °CStorage –55 +125 °CThermal Resistance θJA
8-Pin DIP 100 °C/WSO-8 Surface-Mount 150 °C/WMSOP-8 Surface-Mount 220 °C/W14-Pin DIP 80 °C/WSO-14 Surface-Mount 110 °C/W
Specifications same as OPA234U, E.
NOTES: (1) Wafer-level tested to 95% confidence level. (2) Positive conventional current flows into the input terminals. (3) See Small-Signal Overshoot vs LoadCapacitance typical curve.
![Page 4: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/4.jpg)
OPA234, OPA2234, OPA42344SBOS055Awww.ti.com
PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS
OFFSET VOLTAGEInput Offset Voltage VOS VCM = 0V ±70 ±250 ±500 µV
OPA4234U Model ±70 ±250 µVvs Temperature(1) dVOS/dT Operating Temperature Range ±0.5 ±5 µV/°Cvs Power Supply PSRR VS = ±1.35V to ±18V, VCM = 0V 3 10 20 µV/Vvs Time 0.2 µV/mo
Channel Separation (Dual, Quad) 0.3 µV/V
INPUT BIAS CURRENTInput Bias Current(2) IB VCM = 0V –12 –25 –50 nAInput Offset Current IOS VCM = 0V ±1 ±5 nA
NOISE f = 1kHzInput Voltage Noise Density vn 25 nV/√HzCurrent Noise Density in 80 fA/√Hz
INPUT VOLTAGE RANGECommon-Mode Voltage Range (V–) (V+) –1 VCommon-Mode Rejection CMRR VCM = –15V to 14V 91 106 86 dB
INPUT IMPEDANCEDifferential 107 || 5 Ω || pFCommon-Mode VCM = 0V 1010 || 6 Ω || pF
OPEN-LOOP GAINOpen-Loop Voltage Gain AOL VO = –14.5V to 14V 110 120 100 dB
FREQUENCY RESPONSEGain-Bandwidth Product GBW CL = 100pF 0.35 MHzSlew Rate SR 0.2 V/µsSettling Time: 0.1% G = 1, 10V Step, CL = 100pF 41 µs
0.01% G = 1, 10V Step, CL = 100pF 47 µsOverload Recovery Time (VIN) (Gain) = VS 22 µs
OUTPUTVoltage Output: Positive (V+) –1 (V+) –0.7 V
Negative (V–) +0.5 (V–) +0.15 VShort-Circuit Current ISC ±22 mACapacitive Load Drive (Stable Operation)(3) G = +1 1000 pF
POWER SUPPLYSpecified Operating Voltage ±15 VOperating Voltage Range ±1.35 ±18 VQuiescent Current (per amplifier) IQ IO = 0 ±275 ±350 µA
TEMPERATURE RANGESpecified Range –40 +85 °COperating Range –40 +125 °CStorage –55 +125 °CThermal Resistance θJA
8-Pin DIP 100 °C/WSO-8 Surface-Mount 150 °C/WMSOP-8 Surface-Mount 220 °C/W14-Pin DIP 80 °C/WSO-14 Surface-Mount 110 °C/W
Specifications same as OPA234U, E.
NOTES: (1) Wafer-level tested to 95% confidence level. (2) Positive conventional current flows into the input terminals. (3) See Small-Signal Overshoot vs LoadCapacitance typical curve.
ELECTRICAL CHARACTERISTICS: VS = ±15VAt TA = 25°C, VS = ±15V, and RL = 10kΩ connected to ground, unless otherwise noted.
OPA234U, EOPA2234U
OPA234UA, EAOPA2234UA
OPA4234UA, U
![Page 5: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/5.jpg)
OPA234, OPA2234, OPA4234 5SBOS055A www.ti.com
ELECTROSTATICDISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. TexasInstruments recommends that all integrated circuits be handledwith appropriate precautions. Failure to observe proper han-dling and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-tion to complete device failure. Precision integrated circuitsmay be more susceptible to damage because very smallparametric changes could cause the device not to meet itspublished specifications.
ABSOLUTE MAXIMUM RATINGSSupply Voltage, V+ to V– .................................................................... 36VInput Voltage ..................................................... (V–) –0.7V to (V+) +0.7VOutput Short-Circuit(1) .............................................................. ContinuousOperating Temperature ..................................................–40°C to +125°CStorage Temperature .....................................................–55°C to +125°CJunction Temperature ...................................................................... 150°CLead Temperature (soldering, 10s) ................................................. 300°C
NOTE: (1) Short-circuit to ground, one amplifier per package.
PACKAGEPRODUCT PACKAGE MARKING
SingleOPA234EA MSOP-8 Surface-Mount A34OPA234E " "OPA234UA SO-8 Surface-Mount OPA234UAOPA234U " OPA234U
DualOPA2234UA SO-8 Surface-Mount OPA2234UAOPA2234U " OPA2234U
QuadOPA4234UA SO-8 Surface-Mount OPA4234UAOPA4234U " OPA4234U
NOTE: (1) For the most current package and ordering information, see thePackage Option Addendum located at the end of this data sheet.
PACKAGE INFORMATION
![Page 6: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/6.jpg)
OPA234, OPA2234, OPA42346SBOS055Awww.ti.com
INPUT NOISE AND CURRENT NOISESPECTRAL DENSITY vs FREQUENCY
1
1k
100
10
Vol
tage
Noi
se (
nV/√
Hz)
Cur
rent
Noi
se (
fA/√
Hz)
Frequency (Hz)
10 100 1k 10k 100k
Current Noise
Voltage Noise
TYPICAL CHARACTERISTIC CURVESAt TA = +25°C and RL = 10kΩ, unless otherwise noted.
INPUT BIAS CURRENTvs INPUT COMMON-MODE VOLTAGE
Common-Mode Voltage (V)
Inpu
t Bia
s C
urre
nt (
nA)
–17
–16
–15
–14
–13
–12
–11
–10–15 –10 –5 0 5 10 15
VS = +5V
VS = +2.7V
VS = ±15V
INPUT BIAS AND INPUT OFFSET CURRENTvs TEMPERATURE
Ambient Temperature (°C)
Inpu
t Bia
s, In
put O
ffset
Cur
rent
(nA
)
–20
–15
–10
–5
0
+5–75 –50 –25 0 25 50 75 100 125
VS = +2.7V, +5V
IOS
VS = ±15V
IB
OPEN-LOOP GAIN/PHASE vs FREQUENCY
0.1
140
120
100
80
60
40
20
0
–20
0
–30
–60
–90
–120
–150
–180
Vol
tage
Gai
n (d
B)
Pha
se (
°)
Frequency (Hz)
1 10 100 1k 10k 100k 1M
CL = 100pF
G
φ
VO = 0.25V
VS = +5V±15V
VO =VS
2
VS = +2.7V
CMR
+PSR
POWER-SUPPLY AND COMMON-MODE REJECTIONvs FREQUENCY
Frequency (Hz)
PS
R, C
MR
(dB
)
120
110
100
90
80
70
60
50
40
30
20
10
010 100 1k 10k 100k 1M
–PSR
VS = +2.7V, +5V or ±15VVS = +2.7V or +5VVS = ±15V
CHANNEL SEPARATION vs FREQUENCY
Frequency (Hz)
Cha
nnel
Sep
arat
ion
(dB
)160
140
120
100
80
10 100 1k 10k 100k
Dual and quad devices.G = 1, all channels.Quad measured channelA to D or B to C—othercombinations yield improvedrejection.
RL = 10kΩ
![Page 7: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/7.jpg)
OPA234, OPA2234, OPA4234 7SBOS055A www.ti.com
TYPICAL CHARACTERISTIC CURVES (Cont.)At TA = +25°C and RL = 10kΩ, unless otherwise noted.
OFFSET VOLTAGEPRODUCTION DISTRIBUTION
Per
cent
of A
mpl
ifier
s (%
)
Offset Voltage (µV)
025 25 50 75 125
100
150
175
0.3% 0.1%
200
200
175
150
125
100 75 50
25
20
15
10
5
0
VS = +2.7V, +5VTypical productiondistribution of packagedunits. Single, dual, andquad units included.
0.1%
OFFSET VOLTAGEPRODUCTION DISTRIBUTION
Per
cent
of A
mpl
ifier
s (%
)
Offset Voltage (µV)
0
100
200
300
400
500
–500
–400
–300
–200
–100
30
25
20
15
10
5
0
VS = ±15VTypical productiondistribution of packagedunits. Single, dual,and quad units included.
0.2%
0.3%0.7%
0.1% 0.5%
OFFSET VOLTAGE DRIFTPRODUCTION DISTRIBUTION
Per
cent
of A
mpl
ifier
s (%
)
Offset Voltage Drift (µV/°C)3
3.5 4
4.5 5
0.5 1
1.5 2
2.5
35
30
25
20
15
10
5
0
0.1% 0.1%0.2%0.5%0.3%
VS = +5V Typical productiondistribution of packagedunits. Single, dual,and quad units included.
OFFSET VOLTAGE DRIFTPRODUCTION DISTRIBUTION
Per
cent
of A
mpl
ifier
s (%
)
Offset Voltage Drift (µV/°C)
30
25
20
15
10
5
0
0.5
1.5 21 3
3.5
2.5 4
4.5 5
5.5 6
6.5 7 8
7.5
VS = ±15VTypical productiondistribution of packagedunits. Single, dual,and quad units included.
0.1% 0.1%0.1%0.1%
0.2%0.4% 0.3%
OFFSET VOLTAGE DRIFTPRODUCTION DISTRIBUTION
Per
cent
of A
mpl
ifier
s (%
)
Offset Voltage Drift (µV/°C)
3
3.5 4
4.5 5
0.5 1
1.5 2
2.5
35
30
25
20
15
10
5
0
0.1% 0.1%0.2% 0.1%
0.3%
VS = +2.7V Typical productiondistribution of packagedunits. Single, dual,and quad units included.
AOL, CMR, AND PSR vs TEMPERATURE
Ambient Temperature (°C)
AO
L, C
MR
, PS
R (
dB)
140
130
120
110
100
90
80
70
60–75 –50 –25 0 25 50 75 100 125
CMR
PSR
VCM = (V–) –0.02V to (V+) –1V
AOL
VS = +2.7VVS = +5VVS = ±15V
![Page 8: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/8.jpg)
OPA234, OPA2234, OPA42348SBOS055Awww.ti.com
TYPICAL CHARACTERISTIC CURVES (Cont.)At TA = +25°C and RL = 10kΩ, unless otherwise noted.
LARGE-SIGNAL STEP RESPONSEG = 1, CL = 100pF, VS = +5V
1V/d
iv
10µs/div
SMALL-SIGNAL STEP RESPONSEG = 1, CL = 10,000pF, VS = +5V
20m
V/d
iv
20µs/div
OUTPUT VOLTAGE SWING vs OUTPUT CURRENTV+
(V+) –0.5(V+) –1.0(V+) –1.5(V+) –2.0(V+) –2.5(V+) –3.0
(V–) +3.0(V–) +2.5(V–) +2.0(V–) +1.5(V–) +1.0(V–) +0.5
V–0 ±5 ±10
125°C
85°C
25°C
±15
Output Current (mA)
Out
put V
olta
ge S
win
g (V
)
–55°C
–55°C
–40°C
25°C
85°C125°C
–40°C
High output current maynot be available at lowsupply voltages due tooutput swing limitations.
SMALL-SIGNAL OVERSHOOTvs LOAD CAPACITANCE
70
60
50
40
30
20
10
010pF 100pF 1nF 10nF 100nF
Load Capacitance
Ove
rsho
ot (
%)
G = –1,G = +2
G = +1,VS = +2.7, +5V
G = +1,VS = ±15V
G = ±10
G = –2VO = 100mVp-p
SMALL-SIGNAL STEP RESPONSEG = 1, CL = 100pF, VS = +5V
2µs/div
20m
V/d
iv
SETTLING TIME vs CLOSED-LOOP GAIN
Gain (V/V)
Set
tling
Tim
e (µ
s)
1000
100
10
1±1 ±10 ±100
VS = ±15V,10V Step
VS = +2.7V,1V Step
CL = 100pF
0.1%0.01%
VS = +5V,3V Step
![Page 9: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/9.jpg)
OPA234, OPA2234, OPA4234 9SBOS055A www.ti.com
QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENTvs TEMPERATURE
Temperature (°C)
Qui
esce
nt C
urre
nt (
µA)
525
450
375
300
225
150
75
0
Sho
rt-C
ircui
t Cur
rent
(mA
)
70
60
50
40
30
20
10
0–75 –50 –25 0 25 50 75 100 125
±ISC
±IQ
VS = +2.7VVS = +5VVS = +2.7V or +5VVS = ±15V
APPLICATIONS INFORMATIONThe OPA234 series op amps are unity-gain stable andsuitable for a wide range of general-purpose applications.Power-supply pins should be bypassed with 10nF ceramiccapacitors.
OPERATING VOLTAGE
The OPA234 series op amps operate from single (+2.7V to+36V) or dual (±1.35V to ±18V) supplies with excellentperformance. Specifications are production tested with +2.7V,+5V, and ±15V supplies. Most behavior remains unchangedthroughout the full operating voltage range. Parameterswhich vary significantly with operating voltage are shown inthe Typical Characterisitc curves.
OFFSET VOLTAGE TRIM
Offset voltage of the OPA234 series amplifiers is lasertrimmed and usually requires no user adjustment. TheOPA234 (single op amp version) provides offset voltagetrim connections on pins 1 and 5. Offset voltage can beadjusted by connecting a potentiometer, as shown in Fig-ure 1. This adjustment should be used only to null the offsetof the op amp, not to adjust system offset or offset pro-duced by the signal source. Nulling offset could degradethe offset drift behavior of the op amp. While it is notpossible to predict the exact change in drift, the effect isusually small.
FIGURE 1. OPA234 Offset Voltage Trim Circuit.
V+
V–
100kΩ
OPA234 single op amp only.Use offset adjust pins only to nulloffset voltage of op amp—see text.
Trim Range: ±4mV typ
(V–) = 0V for single supply operation.
OPA2346
7
5
4
3
2
1
10nF
10nF
TYPICAL CHARACTERISTIC CURVES (Cont.)At TA = +25°C and RL = 10kΩ, unless otherwise noted.
MAXIMUM OUTPUT VOLTAGEvs FREQUENCY
100k
Frequency (Hz)
1k 10k
30
25
20
15
10
5
0
Out
put V
olta
ge (
Vp-
p)
VS = ±2.7V
VS = +5V
Maximum output voltagewithout slew-rate induceddistortion.
VS = ±15V
![Page 10: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/10.jpg)
PACKAGING INFORMATION
Orderable Device Status (1) PackageType
PackageDrawing
Pins PackageQty
Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
OPA2234P OBSOLETE PDIP P 8 TBD Call TI Call TI
OPA2234PA OBSOLETE PDIP P 8 TBD Call TI Call TI
OPA2234U ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234U/2K5 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234U/2K5E4 PREVIEW SOIC D 8 TBD Call TI Call TI
OPA2234U/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234UA ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234UA/2K5E4 PREVIEW SOIC D 8 TBD Call TI Call TI
OPA2234UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234UAE4 PREVIEW SOIC D 8 TBD Call TI Call TI
OPA2234UAG4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2234UE4 PREVIEW SOIC D 8 TBD Call TI Call TI
OPA2234UG4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234E/250 ACTIVE MSOP DGK 8 250 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234E/250E4 PREVIEW MSOP DGK 8 250 TBD Call TI Call TI
OPA234E/250G4 ACTIVE MSOP DGK 8 250 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234E/2K5 ACTIVE MSOP DGK 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234E/2K5E4 PREVIEW MSOP DGK 8 2500 TBD Call TI Call TI
OPA234E/2K5G4 ACTIVE MSOP DGK 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234EA/250 ACTIVE MSOP DGK 8 250 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234EA/250E4 PREVIEW MSOP DGK 8 250 TBD Call TI Call TI
OPA234EA/250G4 ACTIVE MSOP DGK 8 250 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234EA/2K5 ACTIVE MSOP DGK 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234EA/2K5E4 PREVIEW MSOP DGK 8 2500 TBD Call TI Call TI
OPA234EA/2K5G4 ACTIVE MSOP DGK 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234P OBSOLETE PDIP P 8 TBD Call TI Call TI
OPA234PA OBSOLETE PDIP P 8 TBD Call TI Call TI
OPA234U ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA234U/2K5 ACTIVE SOIC D 8 2500 Pb-Free CU NIPDAU Level-3-260C-168 HR
PACKAGE OPTION ADDENDUM
www.ti.com 25-Jun-2007
Addendum-Page 1
![Page 11: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/11.jpg)
Orderable Device Status (1) PackageType
PackageDrawing
Pins PackageQty
Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
(RoHS)
OPA234U/2K5E4 ACTIVE SOIC D 8 2500 Pb-Free(RoHS)
CU NIPDAU Level-3-260C-168 HR
OPA234UA ACTIVE SOIC D 8 100 Pb-Free(RoHS)
CU NIPDAU Level-3-260C-168 HR
OPA234UA/2K5 ACTIVE SOIC D 8 2500 Pb-Free(RoHS)
CU NIPDAU Level-3-260C-168 HR
OPA234UA/2K5E4 PREVIEW SOIC D 8 TBD Call TI Call TI
OPA234UA/2K5G4 ACTIVE SOIC D 8 2500 TBD Call TI Call TI
OPA234UAE4 PREVIEW SOIC D 8 TBD Call TI Call TI
OPA234UAG4 ACTIVE SOIC D 8 100 TBD Call TI Call TI
OPA234UG4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234PA OBSOLETE PDIP N 14 TBD Call TI Call TI
OPA4234U ACTIVE SOIC D 14 58 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234U/2K5 ACTIVE SOIC D 14 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234U/2K5E4 PREVIEW SOIC D 14 TBD Call TI Call TI
OPA4234U/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234UA ACTIVE SOIC D 14 58 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234UA/2K5E4 PREVIEW SOIC D 14 TBD Call TI Call TI
OPA4234UA/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234UAE4 PREVIEW SOIC D 14 TBD Call TI Call TI
OPA4234UAG4 ACTIVE SOIC D 14 58 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4234UE4 PREVIEW SOIC D 14 TBD Call TI Call TI
OPA4234UG4 ACTIVE SOIC D 14 58 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part ina new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please checkhttp://www.ti.com/productcontent for the latest availability information and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirementsfor all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be solderedat high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die andpackage, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHScompatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
PACKAGE OPTION ADDENDUM
www.ti.com 25-Jun-2007
Addendum-Page 2
![Page 12: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/12.jpg)
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak soldertemperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it isprovided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to theaccuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to takereasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis onincoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limitedinformation may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TIto Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 25-Jun-2007
Addendum-Page 3
![Page 13: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/13.jpg)
TAPE AND REEL INFORMATION
PACKAGE MATERIALS INFORMATION
www.ti.com 23-May-2007
Pack Materials-Page 1
![Page 14: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/14.jpg)
Device Package Pins Site ReelDiameter
(mm)
ReelWidth(mm)
A0 (mm) B0 (mm) K0 (mm) P1(mm)
W(mm)
Pin1Quadrant
OPA2234U/2K5 D 8 MLA 330 12 6.9 5.4 2.0 8 12 Q1
OPA2234UA/2K5 D 8 MLA 330 12 6.9 5.4 2.0 8 12 Q1
OPA234E/250 DGK 8 CAR 0 0 5.3 3.4 1.4 8 12 NONE
OPA234E/2K5 DGK 8 CAR 0 0 5.3 3.4 1.4 8 12 NONE
OPA234EA/250 DGK 8 CAR 0 0 5.3 3.4 1.4 8 12 NONE
OPA234EA/2K5 DGK 8 CAR 0 0 5.3 3.4 1.4 8 12 NONE
TAPE AND REEL BOX INFORMATION
Device Package Pins Site Length (mm) Width (mm) Height (mm)
OPA2234U/2K5 D 8 MLA 390.0 348.0 63.0
OPA2234UA/2K5 D 8 MLA 390.0 348.0 63.0
OPA234E/250 DGK 8 CAR 346.0 346.0 29.0
OPA234E/2K5 DGK 8 CAR 346.0 346.0 29.0
OPA234EA/250 DGK 8 CAR 346.0 346.0 29.0
OPA234EA/2K5 DGK 8 CAR 346.0 346.0 29.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-May-2007
Pack Materials-Page 2
![Page 15: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/15.jpg)
PACKAGE MATERIALS INFORMATION
www.ti.com 23-May-2007
Pack Materials-Page 3
![Page 16: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/16.jpg)
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE
8
4
0.015 (0,38)
Gage Plane
0.325 (8,26)0.300 (7,62)
0.010 (0,25) NOM
MAX0.430 (10,92)
4040082/D 05/98
0.200 (5,08) MAX
0.125 (3,18) MIN
5
0.355 (9,02)
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)0.260 (6,60)
0.400 (10,60)
1
0.015 (0,38)0.021 (0,53)
Seating Plane
M0.010 (0,25)
0.100 (2,54)
NOTES: A. All linear dimensions are in inches (millimeters).B. This drawing is subject to change without notice.C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
![Page 17: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/17.jpg)
![Page 18: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/18.jpg)
![Page 19: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/19.jpg)
![Page 20: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/20.jpg)
![Page 21: REVISED JUNE 2004 Low-Power, Precision SINGLE-SUPPLY … · 2009. 10. 9. · OPA234, OPA2234, OPA4234 3 SBOS055A ELECTRICAL CHARACTERISTICS: VS = +2.7V At TA = 25°C, VS = +2.7V,](https://reader036.vdocument.in/reader036/viewer/2022071504/612448482d252860187dcdb2/html5/thumbnails/21.jpg)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’sstandard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support thiswarranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarilyperformed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers shouldprovide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, maskwork right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or servicesare used. Information published by TI regarding third-party products or services does not constitute a license from TI to use suchproducts or services or a warranty or endorsement thereof. Use of such information may require a license from a third party underthe patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is anunfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third partiesmay be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or servicevoids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive businesspractice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product wouldreasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreementspecifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramificationsof their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-relatedrequirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding anyapplications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and itsrepresentatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade issolely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements inconnection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI productsare designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use anynon-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
RFID www.ti-rfid.com Telephony www.ti.com/telephony
Low Power www.ti.com/lpw Video & Imaging www.ti.com/videoWireless
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2007, Texas Instruments Incorporated