dreams | beds from the uk's leading bed & mattress store ......m6×45mm x 6pcs m6 × 6pcs...
TRANSCRIPT
Woodstock – Single Bed (Guest unit)
Page 1 of 7
Assembly Instructions
1. We suggest you spend a short time reading through this leaflet and then follow
the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you have all
the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the assembly
should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children’s reach.
The unlikely event that this product has missing or damaged parts, please call
0344 292 0000 to obtain spares.
spare
Before you Start, here are some helpful advices.
Caution when unpacking the
Woodstock Guest Bed unit,
DO NOT REMOVE the string
that holds the leg assembly.
The legs are spring loaded
and if opened without due
care can cause injury.
Please note: The Guest bed
maximum mattress thickness that will
fit under the Single bed cannot
exceed 220mm.
M6×45mm x 6pcs
M6 × 6pcs
Allen Key M4 x 2pcs
Metal washer x 6pcs
Wheel x 4pcs
Screw 4 x 20 x 16pcs
Page 2 of 7
PARTS Fittings
NO. PART LIST QTY
(1) Headboard 01
(2) Footboard 01
(3) Side Rails 02
(4) Guest bed 01
A
B
D
C
E
F
Page 3 of 7
ASSEMBLY
STEP1 - Use bolt (mounted on the
Headboard and Footboard) to
fix the Side Rails (3) onto
Headboard (1) and Footboard
(2) by using Allen Key (C).
Page 4 of 7
ASSEMBLY
STEP 2
NOTE: You have bought your
bed, choosing one of two slat
options; either solid or sprung.
Although both assembly
options are explained here only
one will apply to you. Please
follow the correct procedure for
the slat system which you have
chosen.
Both slats on "Step 2" can be
assembled to the bedstead. You
can make a choice between the
two slats options.
Option "A":
DREAMS FIXED WOOD
SLATS
Carefully locate the slats onto
the unit, as step 2:
Use bolt (A), washer (D) and
JCN nut (B) to fix the unit
using Allen Key (C)
- Option "A"
Page 5 of 7
ASSEMBLY
STEP 2 Option "B":
DREAMS SPRUNG SLATS
(1) Carefully locate the slats
onto the unit.
(2) Use bolt (A), washer (D)
and JCN nut (B) to fix the
unit using Allen Key (C)
- Option "B"
ASSEMBLY
STEP 3 Unpack the Woodstock Guest Bed
unit. DO NOT REMOVE the string
that holds the legs assembly. Place
the Woodstock Guest Bed upside
down position in flat and clean
surface secure all Wheel (E) to the
horizontal frame of legs assembly
into pre-drilled holes with 4 Screws
(F) using Phillips Screwdriver (not
included) as illustrated.
Place the Woodstock Guest Bed in
standing position. Release all string
that holds the legs from opening.
Note: To store first ensure the legs
are retracted before sliding
Woodstock Guest Bed under the
Woodstock Single Bed.
STEP 4
Page 6 of 7
Page 7 of 7
ASSEMBLY
STEP 5
To open the Woodstock Guest
Bed, lift from one end to open
the legs assembly
Lift other end to open the
other legs assembly.
The Woodstock Guest unit
ready to use.
To close leg, lift one end, fold
legs assembly and lay down
the Woodstock Guest unit
Lift other the end, fold the
legs assembly and lay down
the Woodstock Guest unit
The Woodstock Guest unit
ready to store under the
Woodstock Single bed unit.
To use the Guest unit, you
need to slide out the unit from
the Single Bed and to store
you need to slide in to the
Single Bed.
STEP 6
STEP 7
STEP 8
STEP 9
STEP 10
STEP 11