Dyson V6 Motorhead Upper Housing andBrush Bar Housing Replacement

Clear cover that protects and houses the brushbar, susceptible to breakage overtime.

Written By: Addie Hedge

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 7

INTRODUCTION

Connection tube and brushbar will need to be removed before replacement. Housing for thebrushbar may be damaged and break overtime.

TOOLS:iFixit Opening Tools (1)T8 Torx Screwdriver (1)Coin (1)

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 7

Step 1 — Brush Bar

Press the button to disconnect thevacuum head from the connectingpole.

Step 2

Turn the end cap counterclockwiseusing the iFixit Opening Tool.

If you do not have an iFixit OpeningTool, a quarter may be usedinstead.

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 7

Step 3

Pull the brush bar out of the housing.

Step 4 — Upper Housing and Brush Bar Housing

Turn the padlock key counterclockwise using the iFixit Opening Tool.

If you do not have an iFixit Opening Tool, a quarter may be used instead.

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 7

Step 5

Unscrew the three front 1.4 cm torxscrews using the T8 Torxscrewdriver.

Step 6

Remove the upper plate once the padlock is unlocked.

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 7

Step 7

Unscrew the top two corner 1.4 cm torx screws using the iFixit T8 Torx screwdriver.

Remove axie and roller after the screws are taken out.

Step 8

Remove the drive assembly fromvacuum housing.

Red wire connecting the driveassembly to housing.

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 7

To reassemble your device, follow these instructions in reverse order.

Step 9

Pop off the circular plating to remove the housing from the connection piece.

Red wire connects through the upper portion of the housing.

Dyson V6 Motorhead Upper Housing and Brush Bar Housing Replacement Draft: 2017-05-17Guide ID: 76773 -

This document was generated on 2019-09-29 12:52:14 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 7 of 7