eee231- electronics-1 lecture 01
TRANSCRIPT
![Page 1: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/1.jpg)
EEE231 Electronics 1
Lecture 1Course Introduction
&Basic Concepts
![Page 2: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/2.jpg)
Instructor Details(Muhammad Rizwan Azam)
• Educational Backgroundo PHD .. (Control Systems)o MS (Control Systems)o BSc Eng. (Electronics)
• Contact Detailso Room # 113, EE Blocko [email protected]
![Page 3: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/3.jpg)
Course Prerequisites1. Electric Circuit analysis 1 (EEE 121)2. Calculus and Analytic Geometry (MTH104)3. Applied Physics
![Page 4: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/4.jpg)
Marks Distribution (Theory)Sessional -1 10%Sessional 2 15%Quizzes (4) 15%Assignments (4) 10%Terminal Exam 50%
Note: Quizzes will be announced as well un announced.Expect a quiz after submission of assignment.Copied assignments and assignments submitted after the due date will be marked zero.
![Page 5: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/5.jpg)
Course Objectives1. To make students understand construction, physical
characteristics and operation of the major semiconductor devices.
2. To study, analyze and design circuits using semiconductor devices.
3. To illustrate how the device characteristics are utilized in switching, digital, and amplification applications.
![Page 6: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/6.jpg)
Topics to be Covered1) Semiconductor material and properties 2) Diode model, equivalent model and circuit analysis 3) Analysis of diode based circuits (rectifiers, clipper, clampers,
etc.) 4) Special diodes characteristics and applications 5) Bipolar transistors characteristics and modes of operations 6) DC analysis, dc load line, biasing of bipolar transistor
circuits 7) Small signal analysis of bipolar transistor circuits 8) Design and analysis of common bipolar transistor amplifiers
![Page 7: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/7.jpg)
Course Material• Textbooks:
o Electronic Circuits Analysis and Design, 3rd Edition, by Donald A Neamen.
o Electronic devices and circuit theory, 10th ed. Boylestad.• Reference Books:
o Electronic Devices 7th (or 9th ) Edition by Floyd.o Electronics Devices and Circuits, 6th Edition by Bogart.o Introductory Electronic Devices and Circuits, 4th Edition
by Robert T. Paynter.o Microelectronic Circuits 6th Edition by Sedra, Smith.
![Page 8: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/8.jpg)
Why Electronics ?• The giant strides that we have made in the areas of
communications and computers are possible only because of the great successes that we have achieved in the field of electronics.
![Page 9: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/9.jpg)
Some Basic Concepts• Electronics :
o Science of the motion of charges in a gas, vacuum, or semiconductor.
• Ohm’s Law:o The current through a conductor is directly proportional
to the potential difference.
• Electrical Power:o Power is how much work is done over time.
![Page 10: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/10.jpg)
AC and DC• Direct Current (DC):
o Flow of charge in one direction,o Current maintains the same polarity,o DC is produced by sources such as batteries, solar cells
etc.• Alternating Current (AC):
o An alternating voltage source periodically alternates or reverses in polarity.
o The resulting current, therefore, periodically reverses in direction.
![Page 11: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/11.jpg)
Electronic Circuits• In most electronic circuits
o There are two inputs.o One input is from a power supply that provides dc
voltages and currents to establish the proper biasing for the circuit.
o The second input is a signal that can be amplified by the circuit.
o The output signal can be larger than the input signal.
![Page 12: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/12.jpg)
Analog and Digital Signals• Analog Signals
o The magnitude of an analog signal may have any value.o The amplitude may vary continuously with respect to
time.o Electronic circuits that process such signals are called
analog circuits.
![Page 13: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/13.jpg)
Analog and Digital Signals• Digital Signals
o An alternative signal is at one of two distinct levels and is called a digital signal.
o The digital signal has discrete values, it is said to be quantized.
o Electronic circuits that process digital signals are called digital circuits.
![Page 14: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/14.jpg)
Atom• An atom is composed of ;
o A nucleus, which contains positively charged protons and neutral neutrons,
o And negatively charged electrons that, orbit the nucleus. • The electrons are distributed in various “shells” at
different distances from the nucleus, • Electron energy increases as shell radius increases.• Electrons in the outermost shell are called valence electrons,
![Page 15: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/15.jpg)
Electronic Materials
• The basic goal of electronic materials is to generate and control the flow of an electric current.
• Electronic materials include:o Conductors: have low resistance which allows electric
current flowo Insulators: have high resistance which suppresses electric
current flowo Semiconductors: can allow or suppress electrical current flow
![Page 16: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/16.jpg)
Insulators• Insulators have a high resistance so current does not flow
in them.• Have 8 valence electrons• Good insulators include:
o Glass, ceramic, plastics, & wood• Most insulators are compounds of several elements. • The atoms are tightly bound to one another so electrons
are difficult to strip away for current flow.
![Page 17: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/17.jpg)
Insulators
Insulators have tightly bound electrons in their outer shellThese electrons require a very large amount of energy to free them for conduction
Let’s apply a potential difference across the insulator above…
The force on each electron is not enough to free it from its orbit and the insulator does not conduct
Insulators are said to have a high resistivity / resistance
![Page 18: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/18.jpg)
Conductors• Good conductors have low resistance so electrons flow
through them with ease.• Best element conductors include:
o Copper, silver, gold, aluminum, & nickel • Alloys are also good conductors:
o Brass & steel • Good conductors can also be liquid:
o Salt water
![Page 19: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/19.jpg)
Conductors
Conductors have loosely bound electrons in their outer shellThese electrons require a small amount of energy to free them for conduction
Let’s apply a potential difference across the conductor above…
The force on each electron is enough to free it from its orbit and it can jump from atom to atom – the conductor conducts
Conductors are said to have a low resistivity / resistance
![Page 20: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/20.jpg)
Conductor Atomic Structure
• The atomic structure of good conductors usually includes only one electron in their outer shell.
• It is called a valence electron. • It is easily striped from the
atom, producing current flow.
Copper Atom
![Page 21: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/21.jpg)
Semiconductors• A material whose properties are such that it is not quite a
conductor, not quite an insulator.
• Semiconductors have a resistivity/resistance between that of conductors and insulators.
• Their electrons are not free to move but a little energy will free them for conduction
• Some common semiconductorso elemental
• Si - Silicon (most common)• Ge - Germanium
o compound• GaAs - Gallium arsenide• GaP - Gallium phosphide• AlAs - Aluminum arsenide• AlP - Aluminum phosphide• InP - Indium Phosphide
(The resistance of a semiconductor decreases as the temperature increases – Negative Temp. Coefficient)
![Page 22: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/22.jpg)
Semiconductor Valence Orbit
• The main characteristic of a semiconductor element is that it has four electrons in its outer or valence orbit.
![Page 23: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/23.jpg)
Crystal Lattice Structure
• The unique capability of semiconductor atoms is their ability to link together to form a physical structure called a crystal lattice.
• The valence electrons are shared between atoms, forming what are called covalent bonds.
2D Crystal Lattice Structure
![Page 24: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/24.jpg)
The Silicon (Si) AtomSilicon has a valency of 4 i.e. 4 electrons in its outer shell
Each silicon atom shares its 4 outer electrons with 4 neighbouring atoms
These shared electrons – bonds – are shown as horizontal and vertical lines between the atoms
This picture shows the shared electrons
![Page 25: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/25.jpg)
Silicon – the crystal latticeIf we extend this arrangement throughout a piece of silicon…
We have the crystal lattice of silicon
This is how silicon looks when it is cold, i.e. T = 0 K
It has no free electrons – it cannot conduct electricity – therefore it behaves like an insulator
![Page 26: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/26.jpg)
Energy Bands• When silicon atoms come together to form a crystal, the
electrons occupy particular allowed energy bands.
• Minimum energy required to break the covalent bond is Bandgap Energy ().
Free Electrons
Electrons Can not exist here
![Page 27: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/27.jpg)
Electron Hole Pair• When an electron jumps to the conduction band, a
vacancy is left in the valence band within the crystal. This vacancy is called a hole.
![Page 28: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/28.jpg)
Electron Movement in SiliconHowever, if we apply a little heat to the silicon….
An electron may gain enough energy to break free of its bond…
It is then available for conduction and is free to travel throughout the material
![Page 29: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/29.jpg)
Hole Movement in SiliconLet’s take a closer look at what the electron has left behind
There is a gap in the bond – what we call a hole
![Page 30: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/30.jpg)
Hole Movement in SiliconThis hole can also move…
An electron – in a nearby bond – may jump into this hole…
Effectively causing the hole to move…
Like this…
In semiconductors, the negatively charged free electron, and the positivelycharged hole contribute to the current.
![Page 31: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/31.jpg)
Doping• Relying on heat or light for conduction does not make
reliable electronics.• To make the semiconductor conduct electricity, other
atoms called impurities must be added.• “Impurities” are different elements, normally from III
or V group of periodic table. • This process is called doping.
![Page 32: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/32.jpg)
Semiconductor Types• An intrinsic semiconductor, also called an undoped
semiconductor or i-type semiconductor, is a pure semiconductor without any significant dopant species present.
• Since the electron and hole concentrations in an intrinsic semiconductor are relatively small.
• These concentrations can be greatly increased by adding controlled amounts of certain impurities (Doping).
• An extrinsic semiconductor is a semiconductor that has
been doped.
![Page 33: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/33.jpg)
Semiconductors can be Conductors• An impurity, or element like
arsenic, has 5 valence electrons.
• Adding arsenic (doping) will allow four of the arsenic valence electrons to bond with the neighboring silicon atoms.
• The one electron left over for each arsenic atom becomes available to conduct current flow.
![Page 34: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/34.jpg)
The Phosphorus AtomPhosphorus is number 15 in the periodic table
It has 15 protons and 15 electrons – 5 of these electrons are in its outer shell
![Page 35: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/35.jpg)
Doping – Making n-type SiliconSuppose we remove a silicon atom from the crystal lattice…and replace it with a phosphorus atom
We now have an electron that is not bonded – it is thus free for conduction
![Page 36: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/36.jpg)
Doping – Making n-type SiliconLet’s remove another silicon atom…and replace it with a phosphorus atomAs more electrons are available for conduction we have increased the conductivity of the material
If we now apply a potential difference across the silicon…
Phosphorus is called the dopant, or donor impurity,
![Page 37: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/37.jpg)
Extrinsic Conduction – n-type SiliconA current will flow
Note:
The negative electrons move towards the positive terminal
![Page 38: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/38.jpg)
From now on n-type will be shown like this.N-type Silicon
• This type of silicon is called n-type • This is because the majority charge carriers are
negative electrons• A small number of minority charge carriers – holes –
will exist due to electrons-hole pairs being created in the silicon atoms due to heat
• The silicon is still electrically neutral as the number of protons is equal to the number of electrons
![Page 39: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/39.jpg)
The Boron AtomBoron is number 5 in the periodic table
It has 5 protons and 5 electrons – 3 of these electrons are in its outer shell
![Page 40: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/40.jpg)
Doping – Making p-type SiliconAs before, we remove a silicon atom from the crystal lattice…
This time we replace it with a boron atom
Notice we have a hole in a bond – this hole is thus free for conduction
![Page 41: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/41.jpg)
Doping – Making p-type SiliconLet’s remove another silicon atom…
and replace it with another boron atomAs more holes are available for conduction we have increased the conductivity of the material
If we now apply a potential difference across the silicon, hole current starts to flow.
Boron is the dopant here, also called acceptor impurity.
![Page 42: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/42.jpg)
P-type Silicon
• This type of silicon is called p-type • This is because the majority charge carriers are positive
holes• A small number of minority charge carriers – electrons –
will exist due to electrons-hole pairs being created in the silicon atoms due to heat
• The silicon is still electrically neutral as the number of protons is equal to the number of electrons
From now on p-type will be shown like this.
![Page 43: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/43.jpg)
The p-n JunctionSuppose we join a piece of p-type silicon to a piece of n-type silicon
We get what is called a p-n junction
Remember – both pieces are electrically neutral
![Page 44: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/44.jpg)
The p-n JunctionWhen initially joined electrons from the n-type migrate into the p-type – less electron density there
When an electron fills a hole – both the electron and hole disappear as the gap in the bond is filled
This leaves a region with no free charge carriers – the depletion layer – this layer acts as an insulator
![Page 45: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/45.jpg)
The p-n JunctionAs the p-type has gained electrons – it is left with an overall negative charge…
As the n-type has lost electrons – it is left with an overall positive charge…
Therefore there is a voltage across the junction – the junction voltage – for silicon this is approximately 0.6 V
0.6 V
![Page 46: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/46.jpg)
The Reverse Biased P-N JunctionTake a p-n junction
Apply a voltage across it with the
p-type negative
n-type positive
Close the switch
The voltage sets up an electric field throughout the junction The junction is said to be reverse – biased
![Page 47: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/47.jpg)
The Reverse Biased P-N JunctionNegative electrons in the n-type feel an attractive force which pulls them away from the depletion layer
Positive holes in the p-type also experience an attractive force which pulls them away from the depletion layer
Thus, the depletion layer ( INSULATOR ) is widened and no current flows through thep-n junction
![Page 48: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/48.jpg)
The Forward Biased P-N JunctionTake a p-n junction
Apply a voltage across it with the
p-type postitive
n-type negative
Close the switch
The voltage sets up an electric field throughout the junction
The junction is said to be forward – biased
![Page 49: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/49.jpg)
The Forward Biased P-N JunctionNegative electrons in the n-type feel a repulsive force which pushes them into the depletion layer
Positive holes in the p-type also experience a repulsive force which pushes them into the depletion layer
Therefore, the depletion layer is eliminated and a current flows through the p-n junction
![Page 50: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/50.jpg)
The Forward Biased P-N JunctionAt the junction electrons fill holes
They are replenished by the external cell and current flows
Both disappear as they are no longer free for conduction
This continues as long as the external voltage is greater than the junction voltage i.e. 0.6 V
![Page 51: EEE231- Electronics-1 Lecture 01](https://reader035.vdocument.in/reader035/viewer/2022081416/588aba821a28ab371f8b5827/html5/thumbnails/51.jpg)
The Forward Biased P-N JunctionIf we apply a higher voltage…
The electrons feel a greater force and move faster
The current will be greater and will look like
The p-n junction is called a DIODE and is represented by the symbol…
The arrow shows the direction in which it conducts current
this….