epu-4462 4562 bios reference manual...orom ui normal delay..... 23 rst force form ..... 23...

BIOS Reference Manual REV. October 2019

Blackbird (VL-EPU-4562)

ii EPU-4562 BIOS Reference Manual

WWW.VERSALOGIC.COM

12100 SW Tualatin Road Tualatin, OR 97062-7341

(503) 747-2261 Fax (971) 224-4708

Copyright © 2018-2019 VersaLogic Corp. All rights reserved.

Notice: Although every effort has been made to ensure this document is error-free, VersaLogic makes no representations or warranties with respect to this product and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.

VersaLogic reserves the right to revise this product and associated documentation at any time without obligation to notify anyone of such changes.

* Other names and brands may be claimed as the property of others.

http://www.versalogic.com/

EPU-4562 BIOS Reference Manual iii

Product Release Notes This document reflects the content of the BIOS Setup program for the EPU-4562 board.

Board Revision BIOS Version Comments Rev 1.00 1.02 First release of document

Rev 1.02 1.03 Updated Post watchdog default to 30 seconds

Customer Support If you are unable to solve a problem after reading this manual, visiting the product support page, or searching the KnowledgeBase, contact VersaLogic Technical Support at (503) 747-2261. VersaLogic support engineers are also available via e-mail at [email protected].

Repair Service If your product requires service, you must obtain a Returned Material Authorization (RMA) number by calling 503-747-2261. Be ready to provide the following information:

• Your name, the name of your company, your phone number, and e-mail address • The name of a technician or engineer that can be contacted if any questions arise • The quantity of items being returned • The model and serial number (barcode) of each item • A detailed description of the problem • Steps you have taken to resolve or recreate the problem • The return shipping address

Warranty Repair All parts and labor charges are covered, including return shipping charges for UPS Ground delivery to United States addresses.

Non-warranty Repair All approved non-warranty repairs are subject to diagnosis and labor charges, parts charges and return shipping fees. Specify the shipping method you prefer and provide a purchase order number for invoicing the repair.

Note: Mark the RMA number clearly on the outside of the box before returning.

mailto:[email protected]

iv EPU-4562 BIOS Reference Manual

Contents

Main Menu ...................................................................................................................... 2 System Language ................................................................................................................ 2 System Date and Time ........................................................................................................ 2

Advanced Menu ............................................................................................................. 3 Graphics .............................................................................................................................. 4 Watchdog ............................................................................................................................ 7 Security Device Support ................................................................................................ 11 RTC Wake Settings .......................................................................................................... 12 RTC Wake Mode............................................................................................................ 12 Values: Disabled, Wake from S4 and S5 (default), Wake from S3, S4 and S5 .. 12 Wake up hour ................................................................................................................. 12 ACPI ................................................................................................................................. 12

AMT Configuration ............................................................................................. 14 PCH-FW Configuration ....................................................................................... 16

SMART Settings ............................................................................................................... 17 FPGA & Serial Port Configuration................................................................................... 17 Serial Port Console Redirection ....................................................................................... 18 CPU ................................................................................................................................... 20

CPU Information.................................................................................................. 20 Secure Erase...................................................................................................................... 21

Secure Erase mode ............................................................................................... 21 Force Secure Erase .............................................................................................. 21

SATA Configuration ........................................................................................................ 21 SATA Controller(s) ............................................................................................. 21 SATA Mode Selection ......................................................................................... 21 SATA Test Mode ................................................................................................. 21 Software Feature Mask Configuration ................................................................ 22 RAID0 .................................................................................................................. 22 RAID1 .................................................................................................................. 22 RAID10 ................................................................................................................ 22 RAID5 .................................................................................................................. 22 Intel Rapid Recovery Technology ....................................................................... 22 Option ROM UI and Banner ................................................................................ 22 HDD Unlock ........................................................................................................ 22 LED Locate .......................................................................................................... 22 IRRT Only on eSATA ......................................................................................... 23 Smart Response Technology ............................................................................... 23 OROM UI Normal Delay..................................................................................... 23 RST Force Form .................................................................................................. 23 Aggressive LPM Support .................................................................................... 23 SATA Controller Speed ....................................................................................... 23

Acoustic Management ...................................................................................................... 24

Contents

EPU-4562 BIOS Reference Manual v

Acoustic Management Configuration .................................................................. 24 PCI Configuration ............................................................................................................. 25

PCI Latency Timer............................................................................................... 25 PCI-X Latency Timer .......................................................................................... 25 VGA Palette Snoop ............................................................................................. 25 PERR# Generation............................................................................................... 25 SERR# Generation............................................................................................... 25 Above 4G Decoding ............................................................................................ 25 Don't Reset VC-TC Mapping .............................................................................. 25 BIOS Hot-Plug Support ....................................................................................... 25

PCI Express Configuration ............................................................................................... 26 PCI Express Clock Gating ................................................................................... 26 DMI Link ASPM Processor Side ........................................................................ 26 Port8xh Decode ................................................................................................... 26 Peer Memory Write Enable ................................................................................. 26 PCI Express Gen3 Eq Lanes ................................................................................ 27 PCI Express Settings ............................................................................................ 27 PCI Express GEN 2 Settings ............................................................................... 29 PCI Express Port [0-3] ......................................................................................... 31

UEFI Network Stack ......................................................................................................... 35 UEFI Network Stack ............................................................................................ 35 IPv4 PXE Support ................................................................................................ 36 IPv6 PXE Support ................................................................................................ 36 PXE boot wait time .............................................................................................. 36 Media detect count............................................................................................... 36

CSM & Option ROM Control .......................................................................................... 36 CSM Support ....................................................................................................... 36 Gate A20 Active .................................................................................................. 36 Option ROM Messages........................................................................................ 36 INT19 Trap Response .......................................................................................... 37 Boot Option Filter ................................................................................................ 37 PXE Option ROM Launch Policy ....................................................................... 37 Storage Option ROM Launch Policy ................................................................... 37 Video Option ROM Launch Policy ..................................................................... 37 Other Option ROM Launch Policy ...................................................................... 37

NVMe Configuration ........................................................................................................ 37 USB ................................................................................................................................... 38

USB Controllers: ................................................................................................. 38 Overcurrent Protection ........................................................................................ 38 USB Precondition ................................................................................................ 38 XHCI Disable Compliance Mode ........................................................................ 38 xDCI Support ....................................................................................................... 38 USB Port Disable Override ................................................................................. 38 USB SS Physical Connector #[0-3] ..................................................................... 38 USB HS Physical Connector #[0-7] .................................................................... 39 Legacy USB Support ........................................................................................... 39 xHCI Hand-off ..................................................................................................... 39 USB Mass Storage Driver Support ...................................................................... 39

Contents

vi EPU-4562 BIOS Reference Manual

USB hardware delays and time-outs: .................................................................. 39 USB Transfer Timeout ........................................................................................ 39 Device Reset Timeout.......................................................................................... 39 Device Power-up Delay Selection ....................................................................... 39 Device Power-up Delay Value ............................................................................ 40 Mass Storage Devices: ......................................................................................... 40 CD-ROM ............................................................................................................. 40

Diagnostic Settings ........................................................................................................... 40 Relay Interface ..................................................................................................... 40 BC Diagnostic Console Interface ........................................................................ 40 Parity Bit .............................................................................................................. 40 Stop Bits .............................................................................................................. 40 Data Bits .............................................................................................................. 41 Baudrate ............................................................................................................... 41

PC Speaker ........................................................................................................................ 41 Debug Beeps ........................................................................................................ 41 Input Device Debug Beeps .................................................................................. 41 Output Device Debug Beeps ............................................................................... 41 USB Driver Beeps ............................................................................................... 41

Chipset Menu ............................................................................................................... 42 Processor (Integrated Components) .................................................................................. 42

VT-d ..................................................................................................................... 42 Thermal Device (B0:D4:F0) ................................................................................ 42 GMM Device (B0:D8:F0) ................................................................................... 42 CRID Support ...................................................................................................... 42 Above 4GB MMIO BIOS assignment ................................................................. 42 eDRAM Mode ..................................................................................................... 43 DMI/OPI Configuration ....................................................................................... 43 DMI Max Link Speed .......................................................................................... 43 DMI Gen3 Eq Phase 2 ......................................................................................... 43 DMI Gen3 Eq Phase 3 Method ............................................................................ 43 DMI Vc1 Control ................................................................................................. 43 DMI Vcm Control ................................................................................................ 43 Program Static Phase1 Eq .................................................................................... 44 DMI Link ASPM Processor Side ........................................................................ 45 DMI Extended Sync Control ............................................................................... 45 DMI De-emphasis Control ................................................................................... 45 DMI IOT .............................................................................................................. 45

Memory Configuration ..................................................................................................... 46 Sample data:......................................................................................................... 46 MRC ULT Safe Config ....................................................................................... 46 Maximum Memory Frequency ............................................................................ 46 HOB Buffer Size .................................................................................................. 46 ECC Support ........................................................................................................ 46 Max TOLUD ....................................................................................................... 47 SA GV ................................................................................................................. 47 SA GV Low Freq ................................................................................................. 47 Energy Performance Gain .................................................................................... 47

Contents

EPU-4562 BIOS Reference Manual vii

EPG DIMM Idd3N .............................................................................................. 47 EPG DIMM Idd3P ............................................................................................... 47 Retrain on Fast Fail.............................................................................................. 47 Enable RH Prevention ......................................................................................... 48 Hardware RHP (default) ...................................................................................... 48 RH Activation Probability ................................................................................... 48 Exit On Failure (MRC) ........................................................................................ 48 MC Lock .............................................................................................................. 48 Probeless Trace .................................................................................................... 48 Enable/Disable IED (Intel Enhanced Debug) ...................................................... 49 Ch Hash Support .................................................................................................. 49 Ch Hash Mask ...................................................................................................... 49 Ch Hash Interleaved Bit ....................................................................................... 49 VC1 Read Metering ............................................................................................. 49 VC1 RdMeter Time Window .............................................................................. 49 VC1 RdMeter Threshold ..................................................................................... 49 Strong Weak Leaker ............................................................................................ 50 Memory Scrambler .............................................................................................. 50 Channel A DIMM Control ................................................................................... 50 Channel B DIMM Control ................................................................................... 50 Force Single Rank ................................................................................................ 50 Memory Remap ................................................................................................... 50 Time Measure ...................................................................................................... 50 Lpddr Mem WL Set ............................................................................................. 51 EV Loader ............................................................................................................ 51 EV Loader Delay ................................................................................................. 51 Fast Boot .............................................................................................................. 51 DLL Weak Lock Support .................................................................................... 51 Memory Thermal Configuration .......................................................................... 51 Memory Power and Thermal Throttling .............................................................. 52 DDR PowerDown and idle counter ..................................................................... 52 For LPDDR Only: DDR PowerDown and idle counter ...................................... 52 REFRESH_2X_MODE ....................................................................................... 52 LPDDR Thermal Sensor ...................................................................................... 52 SelfRefresh Enable .............................................................................................. 52 SelfRefresh IdleTimer ......................................................................................... 52 Throttler CKEMin Defeature .............................................................................. 53 Throttler CKEMin Timer .................................................................................... 53 Pwr Down Idle Timer .......................................................................................... 53 Dram Power Meter .............................................................................................. 53 Memory Thermal Reporting ................................................................................ 53 Extern Therm Status ............................................................................................ 53 Closed Loop Therm Manage ............................................................................... 53 Open Loop Therm Manage .................................................................................. 54 Memory RAPL .................................................................................................... 54 Memory Thermal Management ........................................................................... 54 Memory Training Algorithms .............................................................................. 54

Platform Controller Hub (PCH)........................................................................................ 54

Contents

viii EPU-4562 BIOS Reference Manual

Isolate SMBus Segments ..................................................................................... 54 CF9h Global Reset ............................................................................................... 54 HD Audio Configuration ..................................................................................... 55 HD Audio ............................................................................................................. 55 Audio DSP ........................................................................................................... 55 HDA-Link Codec Select ...................................................................................... 55 iDisplay Audio Disconnect .................................................................................. 55 PME Enable ......................................................................................................... 55 HD Audio Advanced Configuration .................................................................... 55 I/O Buffer Ownership .......................................................................................... 55 I/O Buffer Voltage Select .................................................................................... 56 HD Audio Link Frequency .................................................................................. 56 iDisplay Link Frequency ..................................................................................... 56 HD Audio DSP Features Configuration .............................................................. 56 DMIC ................................................................................................................... 56 Bluetooth ............................................................................................................. 56 I2S ........................................................................................................................ 56 Voice Activity Detection ..................................................................................... 57 Audio DSP Pre/Post-Processing Module Support: .............................................. 57 TraceHub Configuration Menu ........................................................................... 58 TraceHub Enable Mode ....................................................................................... 58 MemRegion [0-1] Buffer Size ............................................................................. 58 DCI enable (HDCIEN) ........................................................................................ 58 DCI Auto Detect Enable ...................................................................................... 58 PCH LAN Controller ........................................................................................... 58 DeepSx Power Policies ........................................................................................ 59 LAN Wake From DeepSx .................................................................................... 59 Wake on LAN ...................................................................................................... 59 SLP_LAN# Low on DC Power ........................................................................... 59 K1 off ................................................................................................................... 59 Wake on WLAN Enable ...................................................................................... 59 Disable DSX ACPRESENT PullDown ............................................................... 59 Serial IRQ Mode .................................................................................................. 60 Port 61h Bit-4 Emulation ..................................................................................... 60 Port 80h Redirection ............................................................................................ 60 Enhance Port 80h LPC Decoding ........................................................................ 60 Compatible Revision ID ...................................................................................... 60 PCH Cross Throttling .......................................................................................... 60 Pcie Pll SSC ......................................................................................................... 60 Unlock PCH P2SB ............................................................................................... 61 PMC READ DISABLE ....................................................................................... 61

Platform Thermal Configuration ...................................................................................... 61 PCH Thermal Device ........................................................................................... 61 PCH Temp Read .................................................................................................. 61 CPU Energy Read ................................................................................................ 61 CPU Temp Read .................................................................................................. 61 Alert Enable Lock ................................................................................................ 61 PCH Alert ............................................................................................................ 62

Contents

EPU-4562 BIOS Reference Manual ix

DIMM Alert ......................................................................................................... 62

Security Menu .............................................................................................................. 63 Security Settings ............................................................................................................... 63

BIOS Password .................................................................................................... 63 BIOS Lock ........................................................................................................... 63 HDD Security Configuration ............................................................................... 63 Secure Boot Menu ............................................................................................... 63 Key Management ................................................................................................. 64

Boot Menu .................................................................................................................... 66 Boot Configuration ........................................................................................................... 66

Quiet Boot ............................................................................................................ 66 Bootup NumLock State ....................................................................................... 66 Power Loss Control ............................................................................................. 66 AT Shutdown Mode ............................................................................................ 66 Enter Setup If No Boot Device ............................................................................ 66 Enable Popup Boot Menu .................................................................................... 66 Boot Priority Selection ........................................................................................ 67 Battery Support .................................................................................................... 67 System Off Mode ................................................................................................. 67 UEFI Fast Boot .................................................................................................... 67 UEFI Screenshot Capability ................................................................................ 67 New Boot Option Policy ...................................................................................... 67

Save & Exit Menu ........................................................................................................ 68 Save Changes and Exit ........................................................................................ 68 Discard Changes and Exit .................................................................................... 68 Save Changes and Reset ...................................................................................... 68 Discard Changes and Reset ................................................................................. 68 Save Changes ....................................................................................................... 68 Discard Changes .................................................................................................. 68 Default Options .................................................................................................... 68 Restore Defaults .................................................................................................. 68 Save as User Defaults .......................................................................................... 68 Restore User Defaults .......................................................................................... 68 Generate Menu Layout File ................................................................................. 68

Tables

Table 1.Top-level Menu Bar Features ................................................................................ 1 Table 2. BIOS Setup Program Function Keys .................................................................... 1

1 EPU-4562 BIOS Reference Manual

Overview

To access the BIOS Setup program, press during the early boot cycle. The top-level menu bar is shown below.

Aptio Setup Utility Main Advanced Chipset Boot Security Save & Exit ------------------------------------------------------------------------------

Table 1 lists the BIOS Setup program top-level menu bar features.

Table 1. Top-level Menu Bar Features

Menu Function Main Displays processor and memory parameters

Advanced Configures advanced features, including CPU, IDE, and USB

Chipset Configures Northbridge and Southbridge resources

Boot Selects boot device options

Security Sets passwords and security features

Save & Exit Saves or discards changes to Setup program options

Table 2 lists the function keys available for menu screens.

Table 2. BIOS Setup Program Function Keys

Key Function Key Function

or Selects a different menu screen (Moves the cursor left or right)

or

Selects an item (Moves the cursor up or down)

or Changes option/field

Executes a command or selects

a sub-menu

Go to next page

Go to previous page

Go to top of screen

Go to bottom of screen

Select field General help

Load Previous Settings

Loads optimal defaults

Loads failsafe default values

Exit

Save and exit

1 1

EPU-4562 BIOS Reference Manual 2

Main Menu

The Main menu displays BIOS, processor, memory and other system information and edits the system date and time.

System Language The default system language is English.

System Date and Time The system date and time are editable.

2 2


Advanced Menu

The Advanced menu provides access to configuration sub-menus:

• Graphics

• Watchdog

• Module Serial Ports

• Hardware Health Monitoring

• Trusted Computing

• RTC Wake Settings

• ACPI

• AMT Configuration

• PCH-FW Configuration

• SMART Settings

• FPGA & Serial Port Configuration

• Serial Port Console Redirection

• Console Redirection Settings [Windows EMS]

• CPU

• Secure Erase

• SATA Configuration

• Acoustic Management

• PCI Configuration

• UEFI Network Stack

• CSM & Option ROM Control

• NVMe Configuration

• USB

• Diagnostic Settings

3 3

Advanced Menu

EPU-4462/4465 BIOS Reference Manual 4

Graphics Submenu location: Advanced -> Graphics

These options configure graphics settings.

Primary Display Values: Auto (default), IGD, PEG, PCI/PCIe

Select which of IGFX/PEG/PCI Graphics device should be Primary Display.

Primary PCIe Values: Auto (default), PCIE1, PCIE2, PCIE3, PCIE4, PCIE5, PCIE6, PCIE7

Select which graphics device should be Primary PCIE. Auto sets PCIE0.

Internal Graphics Device Values: Auto (default), Disabled, Enabled

Keep Internal Graphics Device (IGD) enabled based on the setup options.

Primary IGD Boot Display Device

Values: Auto (default), CRT, LFP ,EFP, EFP2, EFP3

Primary IGD display in POST. CRT = Analog VGA display port LFP = Local Flat Panel EFPx (External Flat Panel) is a DisplayPort or HDMI/DVI display on DDI1, DDI2 or DDI3.

Active LFP Configuration

Values: No Local Flat Panel,Integrated LVDS (default), eDP

Select active local flat panel configuration.

Always Try Auto Panel Detect

Values: No (default), Yes

If set to 'Yes' the BIOS will first look for an EDID data set in an external EEPROM to configure the LFP. If no external EDID data set can be found the data set selected under 'Local Flat Panel Type' will be used as fallback.

Advanced Menu

5 EPU-4462/4465 BIOS Reference Manual

Local Flat Panel Type

Values: Auto (default), VGA 640x480 1x18 (002h), VGA 640x480 1x18 (013h), WVGA 800x480 1x18 (01Fh), WVGA 800x480 1x24 (01Bh), SVGA 800x600 1x18 (01Ah), XGA 1024x768 1x18 (006h), XGA 1024x768 2x18 (007h), XGA 1024x768 2x24 (012h), WXGA 1280x800 1x18 (01Eh), WXGA 1280x768 1x24 (01Ch), SXGA 1280x1024 2x24 (00Ah), SXGA 1280x1024 2x24 (018h), UXGA 1600x1200 2x24 (00Ch), HD 1920x1080 2x24 (01Dh), WUXGA 1920x1200 2x18 (015h), Customized EDID 1, Customized EDID 2, Customized EDID 3

Select a predefined LFP data set or choose 'Auto' to let the BIOS detect and configure the attached panel. Auto detection is performed by reading an EDID data set via the video I2C bus.

Backlight Inverter Type

Values: None, PWM (default)

Select the type of backlight inverter used. PWM = Use IGD PWM signal. I2C = Use I2C backlight inverter device connected to the video I2C bus.

PWM Inverter Polarity

Values: Normal (default), Inverted

Selects PWM Inverter Polarity

PWM Inverter Frequency (Hz)

Values: 200 (default)

Set the PWM inverter frequency in Hertz (200 - 40000).

Backlight Setting

Values: 0%, 10%, 25%, 40%, 50%, 60%, 75%, 90%, 100% (default)

Actual backlight value in percent of the maximum setting.

Force Backlight Enable

Values: No (default),Yes

Force backlight enable signal active.

Inhibit Backlight

Values: No (default), Permanent, Until End Of POST

Decide whether the backlight on signal should be activated when the panel is activated or whether it should remain inhibited until the end of BIOS POST or permanently.

Advanced Menu


Backlight Delay

Values: No delay (default), 100ms Delay, 250ms Delay, 500ms Delay, 1s Delay

Select delay to be added before driving the panel backlight enable signal active. Can help to avoid panel flickering.

LVDS SSC

Values: Disabled (default), 0.5%, 1.0%, 1.5%, 2.0%, 2.5%

Configure LVDS spread spectrum clock modulation depth. Using center spreading and a fixed modulation frequency of 32.9kHz.

Digital Display Interface 1-3

Values: Auto Selection (default), Disabled, DisplayPort, HDMI/DVI

Select the output type of the digital display interface.

Graphics Turbo IMON Current

Values: 31 (default)

Graphics turbo IMON current values supported (14-31)

Max. GPU Frequency

Values: Default (default), 800 MHz, 700 MHz, 600 MHz, 500 MHz

Allows to limit the maximum frequency of the integrated graphics engine (GT).

GTT Size

Values: 2MB, 4MB, 8MB (default)

Select the GTT Size

Aperture Size

Values: 128MB, 256MB (default), 512MB, 1024MB, 2048MB, 4096MB

Select the Aperture Size Note: Above 4GB MMIO BIOS assignment is automatically enabled when selecting 2048MB aperture. To use this feature, please disable CSM Support.

IGD Total Graphics Memory

Values: 128M, 256M (default), MAX

Select amount of total graphics memory that may be used by the Internal Graphics Device. Memory above the fixed graphics memory will be dynamically allocated by the graphics driver

Advanced Menu


Gfx Low Power Mode

Values: Enabled, Disabled (default)

This option is applicable for SFF only.

VDD Enable

Values: Disabled, Enabled (default)

Enable/Disable forcing of VDD in the BIOS

PAVP Enable

Values: Enabled (default), Disabled

Enable/Disable PAVP

Cdynmax Clamping Enable


Enable/Disable Cdynmax Clamping

Cd Clock Frequency

Values: 337.5 Mhz, 50 Mhz, 540 Mhz, 675 Mhz (default)

Select the highest Cd Clock frequency supported by the platform

Watchdog

Submenu location: Advanced -> Watchdog

POST Watchdog

Values: Disabled, 30sec (default), 1min, 2min, 5min, 10min, 30min

Configure POST watchdog. Started at POST start and stopped at end of POST.

Stop WD For User Interaction

Values: No, Yes (default)

Decide whether POST watchdog should be stopped during setup, popup boot menu or while waiting for password insertion.

Advanced Menu


Runtime Watchdog

Values: Disabled (default), One-time Trigger, Single Event, Repeated Event

Configure runtime watchdog started at end of POST.

Delay

Values: Disabled (default), 10sec, 30sec, 1min, 2min, 5min, 10min, 30min

Event 1

Values: ACPI Event, Reset (default), Power Button

Event 2

Values: Disabled (default), ACPI Event, Reset, Power Button

Event 3

Values: Disabled (default), ACPI Event, Reset (default), Power Button

Timeout [1-3]

Values: 1sec, 2sec, 5sec, 10sec, 30sec (default), 1min, 2min, 5min

Watchdog ACPI Event

Values: Shutdown (default), Restart

Selects the event that is initiated by the watchdog ACPI event. Note: These options perform a critical but orderly OS shutdown or restart.

Module Serial Ports Submenu location: Advanced -> Module Serial Ports

Serial Port 0

Values: Disabled (default), Enabled

Enable or disable module serial port 0.

I/O Base Address

Values: 3F8, 2F8, 220, 228, 238, 2E8, 338h (default), 3E8h

Set serial port base address.

Advanced Menu


Interrupt

Values: None, IRQ3, IRQ4, IRQ5 (default), IRQ6, IRQ14, IRQ15

Set serial port interrupt.

PNP ID

Values: None, PNP0501, CGT0501 (default)

Set serial port ACPI ID.

Baudrate

Values: 2400, 4800, 9600, 19200, 38400, 57600, 115200 (default)

Set serial port initial baudrate

Hardware Health Monitoring Submenu location: Advanced -> Hardware Health Monitoring

Sample Data:

CPU Temperature : +70.0 C

Board Temperature : +57.6 C

DC Input Voltage : 11.945 V

5V Standby : 4.945 V

DC Input Current : 1465 mA

CPU Fan Speed : 0 RPM

Fan PWM Frequency Mode

Values: Low Frequency, High Frequency (default)

Select fan PWM base frequency mode. Low frequency: 11.0Hz-88.2Hz. High frequency: 1kHz-63kHz

Fan PWM Frequency (kHz)

Values: 3 (default)

Select fan PWM base frequency (1kHz-63kHz).

Default Fan Speed

Values: 10%, 15%, ..., 55%, 60% (default), 65%, ..., 95%, 100%

Choose the fan speed value which is valid if the automatic fan speed control has been disabled.

Advanced Menu


Automatic Fan Speed Control


Enable or disable Automatic fan speed control.

Fan Control Temperature

Values: CPU Temperature (default), Board Temperature

Choose the temperature sensor used for fan speed.

Lower Temperature Limit

Values: 10 C (default), 20 C, ..., 80 C, 90 C

Set the temperature which defines the lower limit of the control range.

Upper Temperature Limit

Values: 10 C, 20 C, ..., 70 C, 80 C (default), 90 C

Set the temperature which defines the upper limit of the control range.

Minimum Fan Speed

Values: Fan Off (default), 10%, 15%, ..., 90%, 95%

Choose the fan speed to be set if the temperature is below the lower temperature limit.

Mid Range Bottom Fan Speed

Values: Fan Off, 10%, 15%, ..., 60% (default), ..., 90%, 95%

Choose the fan speed to be set if the temperature is within the lower area of the control range.

Mid Range Top Fan Speed

Values: Fan Off, 10%, 15%, ..., 80% (default), ..., 90%, 95%

Choose the fan speed to be set if the temperature is within the upper area of the control range.

Maximum Fan Speed

Values: 10%, 15%, ..., 95%, 100% (default)

Choose the fan speed to be set if the temperature exceeds the upper temperature limit.

Advanced Menu


Trusted Computing Submenu location: Advanced -> Trusted Computing

Security Device Support

Values: Disable, Enable (default)

Enable or disable BIOS support for security device. O.S. will not show the security device. TCG EFI protocol and INT1A interface will be not available.

SHA-1 PCR Bank

Values: Disabled ,Enabled (default)

Enable or Disable SHA-1 PCR Bank

SHA256 PCR Bank


Enable or Disable SHA256 PCR Bank

Pending operation

Values: None (default), TPM Clear

Schedule an operation or the security device. Note: Your computer will reboot during restart in order to change the state of the security device.

Platform Hierarchy


Enable or Disable platform Hierarchy

Storage Hierarchy


Enable or Disable Storage Hierarchy

Endorsement Hierarchy

Values: Disabled Values: Enabled (default)

Enable or Disable Endorsement Hierarchy

Advanced Menu


TPM2.0 UEFI Spec Version

Values: TCG_1_2, TCG_2 (default)

Select the TCG2 Spec Version Support. TCG_1_2: the Compatible mode for Win8/Win10. TCG_2 Support new TCG2 protocol and event format for Win10 or later

Physical Presence Spec Version

Values: 1.2 (default), 1.3

Select to Tell O.S. to support PPI Spec Version 1.2 or 1.3. Note some HCK tests ight not support 1.3.

RTC Wake Settings Submenu location: Advanced -> RTC Wake Settings

RTC Wake Mode

Values: Disabled, Wake from S4 and S5 (default), Wake from S3, S4 and S5 Set system wake mode on alarm event. When enabled, system will wake from the specified Sx states on the hr::min::sec specified.

Wake up hour

Values: 0 (default)

Select 0-23. For example enter 3 for 3am and 15 for 3pm.

Wake up minute

Values: 0 (default)

0 - 59

Wake up second

Values: 0 (default)

0 - 59

ACPI Submenu location: Advanced -> ACPI

Enable ACPI Auto Configuration


Enables or Disables BIOS ACPI Auto Configuration.

Advanced Menu


Hibernation Support


Enable or disable system ability to hibernate (operating ystem S4 sleep state). This option may not be effective with some operating systems.

ACPI Sleep State

Values: Suspend Disabled, S3 (Suspend to RAM) (default)

Select the state used for ACPI system sleep/suspend.

Lock Legacy Resources


Enable or disable locking of legacy resources.

S3 Video Repost


Enable or disable video BIOS re-post on S3 resume. Required by some operating systems.

ACPI Low Power S0 Idle


Enable or disable ACPI Low Power S0 Idle support.

Automatic Critical Trip Point


Enabled = Configure the critical trip point, the temperature threshold at which the ACPI aware OS performs a critical shutdown, automatically to recommended value. Disabled = Configure the critical trip point manually.

ACPI 3.0 T-States


Enable/Disable ACPI 3.0 T-States.

Native PCI Express Support


Enable or disable native OS PCI Express support.

Advanced Menu


Native ASPM

Values: Disabled (default), Enabled, Auto

Enabled = The OS will control the ASPM support of the PCI Express device. Disabled = The BIOS will control the ASPM support of the PCI Express device.

BDAT ACPI Table Support


Enables support for the BDAT ACPI table.

ACPI Debug


Open a memory buffer for storing debug strings. Use method ADBG to write strings to buffer.

Sleep Button Support


Activate ACPI sleep button support.

AMT Configuration Submenu location: Advanced -> AMT Configuration

Intel AMT


Enable-Disable Intel (R) Active Management Technology BIOS Extension. Note : iAMT H/W is always enabled. This option just controls the BIOS extension execution.

BIOS Hotkey Pressed


OEMFLag Bit 1: Enable/Disable BIOS hotkey press.

MEBx Selection Screen


OEMFLag Bit 2: Enable/Disable MEBx selection screen.

Hide Un-Configure ME Confirmation Prompt


OEMFlag Bit 6: Hide Un-Configure ME without password Confirmation Prompt

Advanced Menu


MEBx Debug Message Output


OEMFlag Bit 14: Enable MEBx debug message output.

Un-Configure ME


OEMFlag Bit 15: Un-Configure ME without password.

Amt Wait Timer

Values: 0 (default)

Set timer to wait before sending ASF_GET_BOOT_OPTIONS.

ASF


Enable/Disable Alert Specification Format.

Activate Remote Assistance Process


Trigger CIRA boot.

USB Provisioning of AMT

Values: Enabled (default)

Enable/Disable of AMT USB Provisioning.

PET Progress


User can Enable/Disable PET Events progress to recieve PET events or not.

Watchdog


Enable/Disable WatchDog Timer.

OS Timer

Values: 0 (default)

Set OS watchdog timer.

Advanced Menu


BIOS Timer

Values: 0 (default)

Set BIOS watchdog timer.

PCH-FW Configuration Submenu location: Advanced -> PCH-FW Configuration

Sample data:

ME FW Version 11.0.10.1002

ME Firmware Mode Normal Mode

ME Firmware Type Full Sku Firmware

ME Firmware SKU Corporate SKU

PTT Capability / State 1 / 0

NFC Support Disabled

ME Unconfig on RTC Clear State


Disabling this option will cause ME not to unconfigure on RTC clear

ME State


Set ME to Soft Temporary Disabled.

TPM Device Selection

Values: dTPM 1.2 (default), PTT

Selects TPM device: PTT or dTPM. PTT - Enables PTT in SkuMgr dTPM 1.2 - Disables PTT in SkuMgr Warning ! PTT/dTPM will be disabled and all data saved on it will be lost.

Firmware Update Configuration

Submenu location: Advanced -> PCH-FW Configuration -> Firmware Update Configuration

Me FW Image Re-Flash


Enable/Disable Me FW Image Re-Flash function.

Advanced Menu


SMART Settings Submenu location: Advanced -> SMART Settings

SMART Self Test


Run SMART self-test on all hard disk drives during POST.

FPGA & Serial Port Configuration Submenu location: Advanced -> FPGA & Serial Port Configuration

Serial Port [1-4] Configuration

Submenu location: Advanced -> FPGA & Serial Port Configuration -> Serial Port [1-4] Configuration

Serial Port

Values: Disabled, Enabled

This will enable or disable the serial port.

Change Settings

Values: Auto (default),IO=3F8h; IRQ=4; (COMA default), IO=2F8h; IRQ=3; (COMB default), IO=3E8h; IRQ=7; (COMC default), IO=2E8h; IRQ=10; (COMD default), IO=3F8h; IRQ=3,4,5,6,7,9,10,11, IO=2F8h; IRQ=3,4,5,6,7,9,10,11, IO=3E8h; IRQ=3,4,5,6,7,9,10,11, IO=2E8h; IRQ=3,4,5,6,7,9,10,11, IO=200h; IRQ=3,4,5,6,7,9,10,11, IO=208h; IRQ=3,4,5,6,7,9,10,11, IO=220h; IRQ=3,4,5,6,7,9,10,11, IO=228h; IRQ=3,4,5,6,7,9,10,11, IO=238h; IRQ=3,4,5,6,7,9,10,11, IO=338h; IRQ=3,4,5,6,7,9,10,11

This selects optimal settings for a Super IO Device.

Transceiver Mode

Values: RS232 (default), RS422, RS485

This selects the UART transceiver mode.

Advanced Menu


Serial Port Console Redirection Submenu location: Advanced -> Serial Port Console Redirection

Console Redirection [COM1-3, Windows EMS]


Console Redirection Settings [COM1-3]

Submenu location: Advanced -> Serial Port Console Redirection -> Console Redirection Settings [COM1-3]

Terminal Type

Values: VT100, VT100+, VT-UTF8, ANSI (default)

Baudrate

Values: 9600, 19200, 38400, 57600, 115200 (default)

Data Bits

Values: 7, 8 (default)

Parity

Values: None (default), Even, Odd, Mark, Space

Stop Bits

Values: 1 (default), 2

Flow Control

Values: None (default), Hardware RTS/CTS

VT-UTF8 Combo Key Support

Values: Disabled, Enabled (default),

Enable VT-UTF8 combination key support for ANSI-VT100 terminals.

Recorder Mode


With this mode enabled only text will be sent. This is to capture terminal data.

Resolution 100x31


Enable or disable extended terminal resolution.

Advanced Menu


Legacy OS Redirection Resolution

Values: 80x24 (default), 80x25

Number of rows and columns supported for legacy OS redirection.

Putty KeyPad

Values: VT100 (default), LINUX, XTERMR6, SCO, ESCN, VT400

Select FunctionKey and KeyPad on Putty.

Redirection After BIOS POST


If BootLoader the is selected, then Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable, which means Legacy console redirection is enabled for Legacy OS.

Console Redirection Settings [Windows EMS]

Submenu location: Advanced -> Serial Port Console Redirection -> Console Redirection Settings [Windows EMS]

Out-of-Band Mgmt Port

Values: COM0 (default), COM1, COM2, COM3

Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS through a serial port.

Terminal Type

Values: VT100, VT100+, VT-UTF8 (default), ANSI

VT-UTF8 is the preferred terminal type for out-of-band management. The next best choice is VT100+ and then VT100.

Baudrate

Values: 9600, 19200, 57600, 115200 (default)

Flow Control

Values: None (default), Hardware RTS/CTS, Software Xon/Xoff

Data Bits

Values: 8

Advanced Menu


Parity

Values: None

Stop Bits

Values: 1

CPU Submenu location: Advanced -> CPU

CPU Information Submenu location: Advanced -> CPU -> CPU Information

Sample data:

Intel(R) Core(TM) i7-6822EQ CPU @ 2.00GHz

CPU Signature: 506E3

Microcode Patch: BA

Max CPU Speed: 2000 MHz

Min CPU Speed : 800 MHz

CPU Speed: 2000 MHz

Processor Cores: 4

Hyper Threading: Supported

Technology

Intel VT-x Technology: Supported

Intel SMX Technology: Supported

64-bit: ;Supported

EIST Technology: Supported

CPU C3 State: Supported



CPU C8 state: Supported



L1 Data Cache: 32 kB x 4

L1 Code Cache: 32 kB x 4

L2 Cache: 256 kB x 4

L3 Cache: 8 MB

L4 Cache: Not Present

Advanced Menu


Secure Erase Submenu location: Advanced -> Secure Erase

Secure Erase mode Values: Real, Simulated (default)

Change behavior of Secure Erase module. <Simulated> Causes the module to show the flow without actually erasing SSD, <Real> causes the module to erase SSD

Force Secure Erase Values: Disable (default), Enable

Force Secure Erase on next boot

SATA Configuration Submenu location: Advanced -> SATA Configuration

SATA Controller(s) Values: Enabled (default), Disabled

Enable or disable the onboard SATA controller(s).

SATA Mode Selection Values: AHCI (default), RAID

Select SATA controller mode. RAID Option is not supported on all chipsets.

SATA Test Mode Values: Enabled (default), Disabled

Should be set to disabled. Test Mode is used just for verification measurements.

Advanced Menu


Software Feature Mask Configuration Submenu location: Advanced -> SATA Configuration -> Software Feature Mask Configuration

RAID0 Values: Disabled, Enabled (default)

Enable or disable RAID0 feature.







Intel Rapid Recovery Technology Values: Disabled, Enabled (default)

Enable or disable Intel Rapid Recovery Technology.

Option ROM UI and Banner Values: Disabled, Enabled (default)

If enabled, then the option ROM user interface is shown. Otherwise, no option ROM banner or information will be displayed if all disks and RAID volumes are normal.

HDD Unlock Values: Disabled, Enabled (default)

If enabled, indicates that the HDD password unlock in the OS is enabled.

LED Locate Values: Disabled, Enabled (default)

Advanced Menu


IRRT Only on eSATA Values: Disabled, Enabled (default)

If enabled, then only Intel Rapid Recovery Technology (IRRT) volumes can span internal and external SATA (eSATA) drives. If disabled, then any RAID volume can span internal and eSATA drives.

Smart Response Technology Values: Disabled, Enabled (default)

Enable or disable Smart Response Technology.

OROM UI Normal Delay Values: 2 Seconds (default), 4 Seconds, 6 Seconds, 8 Seconds

Select the delay time of the OROM UI Splash Screen in a normal status.

RST Force Form Values: Disabled (default), Enabled

Enable/Disable Form for Intel Rapid Storage Technology.

Aggressive LPM Support Values: Enabled, Disabled (default)

Enable PCH to aggressively enter link power state.

SATA Controller Speed Values: Default (default, Gen1, Gen2, Gen3

Indicates the maximum speed the SATA controller can support. Default = maximum speed supported by the chipset Gen1 = 1.5 Gbit/s Gen2 = 3 Gbit/s Gen3 = 6 Gbit/s

Serial ATA Port [0-3] (Drive identification & size) Values: Software Preserve, UNKNOWN, SUPPORTED

SATA Port Values: Disabled, Enabled (default)

Enable or disable the SATA port.

Hot Plug Values: Disabled (default), Enabled

Select hot plug support for this port.

Advanced Menu


External SATA Values: Disabled (default), Enabled

Enable or disable external SATA support.

Spin Up Device Values: Disabled (default), Enabled

When enabled the controller runs an initialization sequence for the connected device during startup.

SATA Device Type Values: Hard Disk Drive (default), Solid State Drive

Identify the SATA port is connected to solid state drive or hard disk drive.

Topology Values: Unknown (default), ISATA, Direct Connect, Flex, M2

Identify the SATA Topology if it is Default or ISATA or Flex or DirectConnect or M2

Device Sleep Values: Disabled (default), Enabled

mSata for RTD3

SATA DEVSLEP Idle Timeout Config Values: Disabled (default), Enabled

Enable/Disable SATA DTIO Config

Acoustic Management Submenu location: Advanced -> Acoustic Management

Acoustic Management Configuration Values: Disabled (default), Enabled

Option to Enable or Disable Automatic Acoustic Management

Advanced Menu


PCI Configuration Submenu location: Advanced -> PCI Configuration

PCI Latency Timer Values: 32 PCI Bus Clocks (default), 64 PCI Bus Clocks, 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI Bus Clocks, 192 PCI Bus Clocks, 224 PCI Bus Clocks, 248 PCI Bus Clocks

The value is programmed into PCI latency timer register.

PCI-X Latency Timer Values: 32 PCI Bus Clocks, 64 PCI Bus Clocks (default), 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI Bus Clocks, 192 PCI Bus Clocks, 224 PCI Bus Clocks, 248 PCI Bus Clocks

Value to be programmed into PCI latency timer register.

VGA Palette Snoop Values: Disabled (default), Enabled

Enable or disable VGA palette registers snooping.

PERR# Generation Values: Disabled (default), Enabled

Enable or disable PCI device to generate PERR#.

SERR# Generation Values: Disabled (default), Enabled

Enable or disable PCI device to generate SERR#.

Above 4G Decoding Values: Disabled (default), Enabled

Enables or Disables 64bit capable Devices to be Decoded in Above 4G Address Space (Only if System Supports 64 bit PCI Decoding).

Don't Reset VC-TC Mapping Values: Disabled (default), Enabled

If system has Virtual Channels, software can reset Traffic Class mapping through Virtual Channels to the default. Setting this option to Enabled will not modify VC Resources.

BIOS Hot-Plug Support Values: Disabled (default), Enabled

If ENABLED allows BIOS build in Hot-Pug support. Use this feature if OS does not support PCI Express and SHPC hot-plug natively.

Advanced Menu


PCI Express Configuration Submenu location: Advanced -> PCI Express Configuration

PCI Express Clock Gating Values: Disabled (default), Enabled

Enable or disable PCI Express clock gating for each root port.

DMI Link ASPM Processor Side Values: Disabled (default), Enabled

Active State Power Management (ASPM) of the DMI link on the Processor side. DMI link is the main bus between the Processor and Platform Controller Hub (PCH).

Port8xh Decode Values: Disabled (default), Enabled

PCI Express Port8xh Decode Enable/Disable.

Peer Memory Write Enable Values: Disabled (default), Enabled

Peer Memory Write Enable/Disable

Compliance Test Mode Values: Disabled (default), Enabled

Enable when using Compliance Load Board

PCIe-USB Glitch W/A Values: Disabled (default), Enabled

PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG Port.

PCIe function swap Values: Disabled (default), Enabled

When Disabled, prevents PCIE rootport function swap. If any function other than 0th is enabled, 0th will become visible.

Advanced Menu


PCI Express Gen3 Eq Lanes Submenu location: Advanced -> PCI Express Configuration -> PCI Express Gen3 Eq Lanes

Overrid e SW EQ settings Values: Disabled (default), Enabled

PCI Express Settings Submenu location: Advanced -> PCI Express Configuration -> PCI Express Settings

PCI Express Device Register Settings

Relaxed Ordering Values: Disabled (default), Enabled

Enable or disable PCI Express device relaxed ordering.

Extended Tag Values: Disabled (default), Enabled

If enabled a device may use an 8-bit tag field as a requester.

No Snoop Values: Disabled, Enabled (default)

Enable or disable PCI Express device 'No Snoop' option.

Maximum Payload Values: Auto (default), 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, 4096 Bytes

Set maximum payload of PCI Express device or allow system BIOS to select the value.

Maximum Read Request Values: Auto (default), 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes,

4096 Bytes

Set maximum read request size of PCI Express device or allow system BIOS to select the value.

Advanced Menu


PCI Express Link Register Settings

ASPM Values: Disabled (default), Auto, Force L0s

PCI Express Active State Power Management settings.

Extended Synch Values: Disabled (default), Enabled

If enabled the generation of extended synchronization patterns is allowed.

Link Training Retry Values: Disabled, 2, 3, 5 (default)

Defines number of retry attempts software will take to retrain the link if previous training attempt was unsuccessful.

Link Training Timeout (us) Values: 1000 (default)

Defines number of microseconds software will wait before polling link training bit in the link status register. Value ranges from 10 to 10000 us.

Unpopulated Links Values: Keep Link On (default), Disabled

In order to save power, software will disable unpopulated PCI Express links, if this option is set to disabled.

Restore PCIe Registers Values: Enabled, Disabled (default)

On non-PCI Express aware operating systems some devices may not be re-initialized correctly after S3. Setting this node to Enabled restores PCI Express configuration on S3 resume.

Advanced Menu


PCI Express GEN 2 Settings Submenu location: Advanced -> PCI Express Configuration -> PCI Express GEN 2 Settings

Completion Timeout Values: Default (default), Shorter, Longer, Disabled

In device Functions that support Completion Timeout programmability, allows system software to modify the Completion Timeout value. 'Default' 50us to 50ms. If 'Shorter' is selected, software will use shorter timeout ranges supported by hardware. If 'Longer' is selected, software will use longer timeout ranges.

ARI Forwarding Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', the Downstream Port disables its traditional Device Number field being 0 enforcement when turning a Type1 Configuration Request into a Type0 Configuration Request, permitting access to Extended Functions in an ARI Device immediately below the Port. Default value: Disabled

AtomicOp Requester Enable Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', this function initiates AtomicOp Requests only if Bus Master Enable bit is in the Command Register Set.

AtomicOp Egress Blocking Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', outbound AtomicOp Requests via Egress Ports will be blocked.

IDO Request Enable Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', this permits setting the number of ID-Based Ordering (IDO) bit (Attribute[2]) requests to be initiated.

IDO Completion Enable Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', this permits setting the number of ID-Based Ordering (IDO) bit (Attribute[2]) requests to be initiated.

Advanced Menu


LTR Mechanism Enable Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', this enables the Latency Tolerance Reporting (LTR) Mechanism.

End-End TLP Prefix Blocking Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', this function will block forwarding of TLPs containing End-End TLP Prefixes.

PCI Express GEN2 Link Register Settings Target Link Speed Values: Auto (default), Force to 2.5 GT/s, Force to 5.0 GT/s

If supported by hardware and set to 'Force to 2.5 GT/s' for Downstream Ports, this sets an upper limit on Link operational speed by restricting the values advertised by the Upstream component in its training sequences. When 'Auto' is selected HW initialized data will be used.

Clock Power Management Values: Disabled (default), Enabled

Enabled', the device is permitted to use CLKREQ# signal for power management of Link clock in accordance to protocol defined in appropriate form factor specification.

Compliance SOS Values: Disabled (default), Enabled

If supported by hardware and set to 'Enabled', this will force LTSSM to send SKP Ordered Sets between sequences when sending Compliance Pattern or Modified Compliance Pattern.

Hardware Autonomous Width Values: Enabled (default), Disabled

If supported by hardware and set to 'Disabled', this will disable the hardware's ability to change link width except width size reduction for the purpose of correcting unstable link operation.

Advanced Menu


Hardware Autonomous Speed Values: Enabled (default), Disabled

If supported by hardware and set to 'Disabled', this will disable the hardware's ability to change link speed except speed rate reduction for the purpose of correcting unstable link operation.

PCI Express Port [0-3] Submenu location: Advanced -> PCI Express Configuration -> PCI Express Port [0-3]

PCI Express Port Values: Disabled, Enabled (default)

Control the PCI Express port.

Topology Values: Unknown (default), x1, x4, Sata Express, M2

Identify the SATA Topology if it is Default or ISATA or Flex or DirectConnect or M2

ASPM Values: Disabled (default), L0s, L1, L0sL1, Auto

PCI Express Active State Power Management settings.

Gen3 Eq Phase3 Method Values: Hardware, Static Coeff., Software Search (default)

PCIe Gen3 Equalization Phase 3 Method

UPTP Values: 5 (default)

Upstream Port Transmitter Preset

DPTP Values: 7 (default)

Downstream Port Transmitter Preset

Advanced Menu


ACS Values: Disabled, Enabled (default)

Enable/Disable Access Control Service Extended Capabilty.

URR Values: Disabled (default), Enabled

Enable or disable PCI Express Unsupported Request Reporting.

FER Values: Disabled (default), Enabled

Enable or disable PCI Express Device Fatal Error Reporting.

NFER Values: Disabled (default), Enabled

Enable or disable PCI Express Device Non-Fatal Error Reporting.

CER Values: Disabled (default), Enabled

Enable or disable PCI Express Device Correctable Error Reporting.

CTO Values: Disabled (default), Enabled

Enable or disable PCI Express Completion Timer TO.

SEFE Values: Disabled (default), Enabled

Enable or disable Root PCI Express System Error on Fatal Error.

SENFE Values: Disabled (default), Enabled

Enable or disable Root PCI Express System Error on Non-Fatal Error.

SECE Values: Disabled (default), Enabled

Enable or disable Root PCI Express System Error on Correctable Error.

Advanced Menu


PME SCI Values: Disabled, Enabled (default)

Enable or disable PCI Express PME SCI.

Hot Plug Values: Disabled (default), Enabled

Enable or disable PCI Express Hot Plug.

Advanced Error Reporting Values: Disabled, Enabled (default)

Advanced Error Reporting Enable/Disable.

PCIe Speed Values: Auto, Gen1, Gen2 (default), Gen3

Select PCI Express port speed.

Transmitter Half Swing Values: Disabled (default), Enabled

Transmitter Half Swing Enable/Disable.

Extra Bus Reserved Values: 0 (default)

Extra Bus Reserved (0-7) for bridges behind this Root Bridge.

Reseved Memory 1 (default)

Reserved Memory Range for this Root Bridge.

Prefetchable Memory Values: 10 (default)

Prefetchable Memory Range for this Root Bridge.

Advanced Menu


Reserved I/O Values: 4 (default)

Reserved I/O (4K/8K/12K/16K/.../48K) Range for this Root Bridge.

PCIE Cp Values: 2 (default)

Gen3 Equalization settings for physiacal PCIe lane.

PCIE Cm Values: 0 (default)

Gen3 Equalization settings for physiacal PCIe lane.

PCIE LTR Values: Disabled, Enabled (default)

PCIE Latency Reporting Enable/Disable.

PCIE LTR Lock Values: Disabled (default), Enabled

PCIE LTR Configuration Lock.

PCH PCIe CLKREQ# Configuration

PCIE5 CLKREQ Mapping Override Values: Default (default), No CLKREQ, Custom number

PCIE CLKREQ Override for default platform mapping.

CLKREQ Number Values: 0 (default)

PCIE CLKREQ Number to be set (LP[0:5], H[0:15])

Snoop Latency Ocerride Values: Disabled, Manual, Auto (default)

Snoop Latency Ocerride for PCH PCIE.

Advanced Menu


Snoop Latency Multiplier Values: 1 ns, 32 ns, 1024 ns (default), 32768 ns, 1048576 ns, 33554432 ns

Snoop Latency Multiplier for PCH PCIE.

Snoop Latency Value Values: 60 (default)

Snoop Latency Value for PCH PCIE.

Non Snoop Latency Ocerride Values: Disabled, Manual, Auto (default)

Non Snoop Latency Ocerride for PCH PCIE.

Non Snoop Latency Mul tiplier Values: 1 ns, 32 ns, 1024 ns (default), 32768 ns, 1048576 ns, 33554432 ns

Non Snoop Latency Multiplier for PCH PCIE.

Force LTR Override Values: Disabled (default), Enabled

Force LTR Override for PCH PCIE. Disabled: LTR override values will not be forced. Enable: LTR override values will be forced and LTR messages from the device will be ignored.

Non Snoop Latency Value Values: 60 (default)

Non Snoop Latency Value for PCH PCIE.

UEFI Network Stack Submenu location: Advanced -> UEFI Network Stack

UEFI Network Stack Values: Disabled (default), Enabled

Enable or disable the UEFI network stack.

Advanced Menu


IPv4 PXE Support Values: Disabled, Enabled (default)

Enable IPv4 PXE boot support. If disabled IPv4 PXE boot option will not be created.

IPv6 PXE Support Values: Disabled, Enabled (default)

Enable IPv6 PXE boot support. If disabled IPv6 PXE boot option will not be created.

PXE boot wait time Values: 0 (default)

Wait time to press ESC key to abort the PXE boot

Media detect count Values: 1 (default)

Number of times presence of media will be checked

CSM & Option ROM Control Submenu location: Advanced -> CSM & Option ROM Control

Compatibility Support Module Configuration

CSM Support Values: Disabled, Enabled (default)

Enable/Disable CSM Support.

CSM16 Module Version 07.79

Gate A20 Active Values: Upon Request (default), Always

Upon Request: Gate A20 can be disabled using BIOS services. Always: Do not allow disabling Gate A20. This option is useful when any runtime code is executed above 1MB.

Option ROM Messages Values: Force BIOS (default), Keep Current

Set display mode for option ROMs.

Advanced Menu


INT19 Trap Response Values: Immediate (default), Postponed

BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE - execute the trap right away; POSTPONED - execute the trap during legacy boot.

Boot Option Filter Values: UEFI and Legacy (default), Legacy only, UEFI only

Controls which devices / boot loaders the system should boot to.

Option ROM execution

PXE Option ROM Launch Policy Values: Do not launch, UEFI ROM Only, Legacy ROM Only (default)

Controls the execution of UEFI and legacy PXE option ROMs.

Storage Option ROM Launch Policy Values: Do not launch, UEFI ROM Only (default), Legacy ROM Only

Controls the execution of UEFI and legacy mass storage device option ROMs.

Video Option ROM Launch Policy Values: Do not launch, UEFI ROM Only, Legacy ROM Only (default)

Controls the execution of UEFI and legacy video option ROMs.

Other Option ROM Launch Policy Values: Do not launch, UEFI ROM Only (default), Legacy ROM Only

Controls the execution of option ROMs for PCI / PCI Express devices other than network, mass storage or video.

NVMe Configuration Submenu location: Advanced -> NVMe Configuration

NVMe controller and Drive information

Advanced Menu


USB Submenu location: Advanced -> USB

USB Controllers: Values: 1 XHCI, USB Devices: 1 Keyboard, 1 Mouse, 1 Hub

Overcurrent Protection Values: Disabled (default), Enabled

Overcurrent protection on all USB ports

USB Precondition Values: Enabled, Disabled (default)

Precondition work on USB host controller and root ports for faster enumeration.

XHCI Disable Compliance Mode Values: FALSE (default), TRUE

Options to disable Compliance Mode. Default is FALSE to not disable Compliance Mode. Set TRUE to disable Compliance Mode.

xDCI Support Values: Disabled (default), Enabled

Enable/Disable xDCI (USB OTG Device).

USB Port Disable Override Values: Disabled (default), Select Per-Pin

Selectively Enable/Disable the corresponding USB port from reporting a Device Connection to the controller.

USB SS Physical Connector #[0-3] Values: Disabled, Enabled (default)

Advanced Menu


USB HS Physical Connector #[0-7] Values: Disabled, Enabled (default)

Legacy USB Support Values: Enabled (default), Disabled, Auto

Enables legacy USB support. Auto option disables legacy support if no USB devices are connected. Disable option will keep USB devices available only for EFI applications and BIOS

xHCI Hand-off Values: Enabled (default), Disabled

This is a workaround for OSes without xHCI hand-off support. The xHCI ownership change should be claimed by xHCI OS driver.

USB Mass Storage Driver Support Values: Disabled, Enabled (default)

Enable or disable USB mass storage driver support.

USB hardware delays and time-outs:

USB Transfer Timeout Values: 1 sec, 5 sec, 10 sec, 20 sec (default)

The timeout value for control, bulk, and interrupt transfers.

Device Reset Timeout Values: 10 sec, 20 sec (default), 30 sec, 40 sec

USB mass storage device Start Unit command timeout.

Device Power-up Delay Selection Values: Auto (default), Manual

Define maximum time a USB device might need before it properly reports itself to the host controller. Auto selects a default value which is 100ms for a root port or derived from the hub descriptor for a hub port.

Advanced Menu


Device Power-up Delay Value Values: 1 (default),

Delay range is 1..40 seconds, in one second increments.

Mass Storage Devices: Values: [Device Name]: Auto (default), Floppy, Forced FDD, Hard Disk

CD-ROM Mass storage device emulation type. 'AUTO' enumerates devices according to their media format. Optical drives are emulated as 'CDROM', drives with no media will be emulated according to a drive type.

Diagnostic Settings Submenu location: Advanced -> Diagnostic Settings

Relay Interface Values: Disabled, I2C, SMBus, BC Diagnostic Console

Select the relay interface to which the POST code will be redirected.

BC Diagnostic Console Interface Values: Disabled (default), BC AUX Port, BC COM Port 0, BC COM Port 1

Select the interface to be used for the BC Diagnostic Console output or disable the BC Diagnostic Console output.

Parity Bit Values: No Parity (default), Even Parity, Odd Parity

Choose the parity bits for the BC Diagnostic Console Interface.

Stop Bits Values: 1 Stop Bit (default), 2 Stop Bits

Choose the stop bits for the BC Diagnostic Console Interface.

Advanced Menu


Data Bits Values: 5 Data Bits, 6 Data Bits, 7 Data Bits, 8 Data Bits (default)

Choose the data bits for the BC Diagnostic Console Interface.

Baudrate Values: 1200 Baud, 2400 Baud, 4800 Baud, 9600 Baud (default), 19200 Baud, 38400

Baud

Choose the baudrate for the BC Diagnostic Console Interface.

PC Speaker Submenu location: Advanced -> PC Speaker

Debug Beeps Values: Disabled, Enabled (default)

Enable or disable general debug / status beep generation.

Input Device Debug Beeps Values: Disabled (default), Enabled

Enable or disable input device debug beeps.

Output Device Debug B eeps Values: Disabled (default), Enabled

Enable or disable output device debug beeps.

USB Driver Beeps Values: Disabled (default), Enabled

Enable or disable USB driver beeps.


Chipset Menu

Processor (Integrated Components) Submenu location: Chipset -> Processor (Integrated Components) Max TOLUD

Sample Data:

Processor Codename Skylake

SA PCIe Code Version 2.0.0.0

VT-d Supported

VT-d Values: Disabled, Enabled (default)

VT-d capability

Thermal Device (B0:D4:F0) Values: Enabled, Disabled (default)

Enable or disable thermal device.

GMM Device (B0:D8:F0) Values: Enabled (default), Disabled

Enable/Disable SA GMM Device.

CRID Support Values: Enabled, Disabled (default)

Enable/Disable CRID control for Intel SIPP

Above 4GB MMIO BIOS assignment Values: Enabled, Disabled (default)

Enable/Disable above 4GB MemoryMappedIO BIOS assignment. This is disabled automatically when Aperture Size is set to 2048MB.

4

Chipset Menu


eDRAM Mode Values: SW Mode eDRAM Off, SW Mode eDRAM On, eDRAM HW Mode (default)

SW Mode eDRAM On or eDRAM Off

DMI/OPI Configuration Submenu location: Chipset -> Processor (Integrated Components) -> DMI/OPI Configuration

DMI Max Link Speed Values: Auto (default), Gen1, Gen2, Gen3

Set DMI Speed Gen1/Gen2/Gen3

DMI Gen3 Eq Phase 2 Values: Disabled, Enabled, Auto (default)

Perform Gen3 Equalization Phase 2

DMI Gen3 Eq Phase 3 Method Values: Auto (default), Adaptive Hardware Equalization, Adaptive Software Equalization, Static Equalization, Disabled

Select Method for Gen3 Equalization Phase 3

DMI Vc1 Control Values: Enabled, Disabled (default)

Enable or disable DMI Vc1.

DMI Vcm Control Values: Enabled (default), Disabled

Enable or disable DMI Vcm.

Chipset Menu


Program Static Phase1 Eq Values: Disabled, Enabled (default)

Program Phase1 Presets/CTLEp

Gen3 Root Port Preset value for each Lane Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> DMI/OPI Configuration -> Gen3 Root Port Preset value for each Lane

Lane [0-3] Values: 4 (default)

Value for lane [0-3]

Gen3 Endpoint Preset value for each Lane Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> DMI/OPI Configuration -> Gen3 Endpoint Preset value for each Lane



Gen3 Endpoint Hint value for each Lane Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> DMI/OPI Configuration -> Gen3 Endpoint Hint value for each Lane



Gen3 RxCTLE Control Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> DMI/OPI Configuration -> Gen3 RxCTLE Control

Bundle0 Values: 3 (default)

Gen3 RxCTLE setting for Bundle0 (Lane0, Lane1)

Chipset Menu


Bundle1 Values: 3 (default)

Gen3 RxCTLE setting for Bundle1 (Lane2, Lane3)

DMI Link ASPM Processor Side Values: Disabled (default), L1

Active State Power Management (ASPM) of the DMI link on the Processor side. DMI link is the main bus between the Processor and Platform Controller Hub (PCH).

DMI Extended Sync Control Values: Enabled, Disabled (default)

Enable DMI extended synchronization.

DMI De-emphasis Control Values: -6 dB, -3.5 dB (default)

Configure the de-emphasis control on DMI.

DMI IOT Values: Enabled, Disabled (default)

Enable or disable DMI IOT.

Chipset Menu


Memory Configuration Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> Memory Configuration

Sample data: Memory RC Version 2.0.0.1

Memory Frequency 2133 MHz

Total Memory 16384 MB

VDD 1200

DIMM#0 16384 MB

DIMM#2 Not Present

Memory Timings 15-36

(tCL-tRCD-tRP-tRAS)

MRC ULT Safe Config Values: Disabled (default), Enabled

MRC ULT Safe Config for PO

Maximum Memory Frequency Values: Auto, 1067, 1333, 1600, 1867, 2133 (default), 2400, 2667, 2933, 3200

Maximum memory frequency selections in [MHz].

HOB Buffer Size Values: Auto (default), 1B, 1KB, Max (assuming 63KB total HOB size)

Size to set HOB Buffer

ECC Support Values: Disabled,Enabled (default),

Enable/disable DDR Ecc Support

Chipset Menu


Max TOLUD Values: Dynamic (default), 1 GB, 1.25 GB, 1.5 GB, 1.75 GB, 2 GB, 2.25 GB, 2.5 GB, 2.75 GB, 3 GB, 3.25 GB, 3.5 GB

Maximum value of TOLUD Dynamic assignment would adjust TOLUD automatically based on largest MMIO length of installed graphic controller.

SA GV Values: Disabled, Fixed Low, Fixed High, Enabled (default)

System Agent Geyserville. Fixed Low/High: SA GV disabled, MRC only runs tasks from Low or High point

SA GV Low Freq Values: MRC default (default), 1067, 1200, 1333, 1400, 1600, 1800, 1867

System Agent Geyserville. Set frequency for low point. Default 1067 for LPDDR3/DDR3, 1333 for DDR4.

Energy Performance Gain Values: Disabled (default), Enabled

Enable/disable Energy Performance Gain.

EPG DIMM Idd3N Values: 26 (default)

Active standby current (Idd3N) in milliamps from datasheet. Must be calculated on a per DIMM basis.

EPG DIMM Idd3P Values: 11 (default)

Active power-down current (Idd3P) in milliamps from datasheet. Must be calculated on a per DIMM basis.

Retrain on Fast Fail Values: Disabled, Enabled (default)

Restart MRC in Cold mode if SW MemTest fails during Fast flow. Default = Enabled

Chipset Menu


Enable RH Prevention Values: Disabled, Enabled (default)

Actively prevent Row Hammer

Row Hammer Solution

Hardware RHP (default) Values: 2x Refresh

Type of method used to prevent Row Hammer

RH Activation Probability Values: 1/2^1, 1/2^2

...

1/2^11 (default)

...

1/2^14, 1/2^15

Used to adjust MC for Hardware RHP.

Exit On Failure (MRC) Values: Disabled, Enabled (default)

Exit On Failure for MRC training steps

MC Lock Values: Disabled, Enabled (default)

Enable/Disable capacity to lock or not MC registers

Probeless Trace Values: Disabled (default), GDXC IOT/MOT, HD Port

HD Port, GDXC IOT/MOT or Disabled

Chipset Menu


Enable/Disable IED (Intel Enhanced Debug) Values: Enabled, Disabled (default)

Intel Enhanced Debug requires 4MB SMM memory

Ch Hash Support Values: Disabled, Enabled (default)

Enable or disable channel hash support. Note: Only if memory interleaved mode.

Ch Hash Mask Values: 12488 (default)

Set the BIT(s) to be included in the XOR function. NOTE BIT mask corresponds to BITS [19:6}

Ch Hash Interleaved Bit Values: BIT6, BIT7, BIT8 (default), BIT9, BIT10, BIT11, BIT12, BIT13

Select the BIT to be used for Channel Interleaved mode. NOTE: BIT7 will interlave the channels at a 2 cacheline granularity, BIT8 at 4 and BIT9 at 8

VC1 Read Metering Values: Disabled, Enabled (default)

Enable/Disable VC1 Read Metering Feature (RdMeter)

VC1 RdMeter Time Window Values: 800 (default)

VC1 Read Metering Time Window: time window over which VC1 read request counter is tracked. Configurable for tens of microseconds window size.

VC1 RdMeter Threshold Values: 280 (default)

VC1 Read Metering Threshold: threshold of counter within time window.

Chipset Menu


Strong Weak Leaker Values: 7 (default)

Value for StrongWkLeaker

Memory Scrambler Values: Disabled, Enabled (default)

Enable or disable memory scrambler support.

Channel A DIMM Control Values: Enable both DIMMs (default), Disable DIMM0, Disable DIMM1, Disable both DIMMs

Channel A DIMM Control Support - Enable or Disable Dimms on Channel A.

Channel B DIMM Control Values: Enable both DIMMs (default), Disable DIMM0, Disable DIMM1, Disable both DIMMs

Channel B DIMM Control Support - Enable or Disable Dimms on Channel B.

Force Single Rank Values: Disabled (default), Enabled

When enabled, only Rank 0 will be used in each DIMM

Memory Remap Values: Enabled (default), Disabled

Enable/Disable Memory Remap above 4GB

Time Measure Values: Disabled (default), Enabled

Enable/Disable printing of the time it takes to execute MRC.

Chipset Menu


Lpddr Mem WL Set Values: Set A, Set B (default)

Only applicable to LPDDR, Memory Write Latency Set selection (A is default, B will be used if memory devices support it)

EV Loader Values: Disabled (default), Enabled

Enable/Disable EV Loader Functionality

EV Loader Delay Values: Enabled (default), Disabled

Enable/Disable EV Loader 2 Second Delay

Fast Boot Values: Enabled (default), Disabled

Enable/Disable fast path thru the MRC

DLL Weak Lock Support Values: Disabled, Enabled (default)

Enable/Disable Dll Weaklock support

Memory Thermal Configuration Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> Memory Configuration -> Memory Thermal Configuration

Chipset Menu


Memory Power and Thermal Throttling Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> Memory Configuration -> Memory Thermal Configuration -> Memory Power and Thermal Throttling]

DDR PowerDown and idle counter Values: PCODE, BIOS (default)

BIOS: BIOS is in control of DDR CKE mode and idle timer value. PCODE: pcode will manage the modes.

For LPDDR Only: DDR PowerDown and idle counter Values: PCODE, BIOS (default)

For LPDDR Only: BIOS: BIOS is in control of DDR CKE mode and idle timer value. PCODE: pcode will manage the modes.

REFRESH_2X_MODE Values: Disabled: 1- Enabled for WARM or HOT (default), 2- Enabled HOT only

0- Disabled 1-iMC enables 2xRef when Warm and Hot 2- iMC enables 2xRef when Hot

LPDDR Thermal Sensor Values: Disabled, Enabled (default)

When enabled, MC uses MR4 to read LPDDR thermal sensors

SelfRefresh Enable Values: Disabled, Enabled (default)

Enable, Disable (Enable= Def)

SelfRefresh IdleTimer Values: 512 (default)

range [64K-1;512]in DLCK800s, (512= Def)

Chipset Menu


Throttler CKEMin Defeature Values: Enabled, Disabled (default)

On, Off

Throttler CKEMin Timer Values: 48 (default)

Timer value for CKEMin, range[255;0]. Req.d min of SC_ROUND_T + BYTE_LENGTH (4)

Pwr Down Idle Timer Values: 0 (default)

The minimum value should = to the worst case Roundtrip delay + Burst_Length. 0 means AUTO: 64 for ULX/ULT, 128 for DT/Halo

Dram Power Meter [Do not modify]

Memory Thermal Reporting Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> Memory Configuration -> Memory Thermal Configuration -> Memory Power and Thermal Throttling -> Memory Thermal Reporting

Extern Therm Status Values: Disabled, Enabled (default)

Enabled: The value from EXTTS is used Disabled: Pcode ignores the EXTTS.

Closed Loop Therm Manage Values: Disabled, Enabled (default)

Enabled: CLTM pcode algorithm will be used. Note: CLTM will preceed OLTM

Chipset Menu


Open Loop Therm Manage Values: Disabled, Enabled (default)

Enabled: OLTM pcode algorithm will be used. Note: CLTM will preceed OLTM

Memory RAPL [Do not modify]

Memory Thermal Management Values: Disabled (default), Enabled

Enable/Disable Memory Thermal Management.

Memory Training Algorithms Submenu location: Submenu location: Chipset -> Processor (Integrated Components) -> Memory Configuration -> Memory Training Algorithm

[Do not modify]

Platform Controller Hub (PCH) Submenu location: Chipset -> Platform Controller Hub (PCH)

Sample data:

Intel PCH RC Version 2.0.0.0

Intel PCH SKU Name PCH-H Mobile QM170

Intel PCH Rev ID 31/D1

Isolate SMBus Segments Values: Never, During POST, Always (default)

Allows isolating the off-module/external SMBus segment from the on-module SMBus segment. This can be a workaround for non-spec conform external SMBus devices.

CF9h Global Reset Values: Host only (default), Host+ME

A CF9h write of 6h or Eh will reset either the host partition only or both, the host and Intel ME partition.

Chipset Menu


HD Audio Configuration Submenu location: Chipset -> Platform Controller Hub (PCH) -> HD Audio Configuration

HD Audio Values: Disabled, Enabled, Auto (default)

Control Detection of the HD-Audio device. Disabled = HDA will be unconditionally disabled Enabled = HDA will be unconditionally enabled Auto = HDA will be enabled if present, disabled otherwise.

Audio DSP Values: Disabled (default), Enabled

Enable/Disable Audio DSP.

HDA-Link Codec Select Values: Platform Onboard (default), External Kit

Selects whether Platform Onboard Codec (single Verb Table installed) or External Codec Kit (multiple Verb Tables installed) will be used.

iDisplay Audio Disconnect Values: Disabled (default), Enabled

Disconnects SDI2 signal to hide/disable iDisplay Audio Codec.

PME Enable Values: Disabled (default), Enabled

Enable/Disable Power Management capability of Audio Controller.

HD Audio Advanced Configuration Submenu location: Chipset -> Platform Controller Hub (PCH) -> HD Audio Configuration -> HD Audio Advanced Configuration

I/O Buffer Ownership Values: HD-Audio Link (default), HD-Audio Link / I2S Port, I2S Port

Selects the ownership of the I/O buffer between Intel HD Audio link vs I2S port (for bilingual codecs).

Chipset Menu


I/O Buffer Voltage Select Values: 3.3V (default), 1.8V

Selects the voltage operation mode of the I/O buffer.

Statically Switchable BCLK Clock Frequency Configuration:

HD Audio Link Frequency Values: 6 MHz, 12 MHz, 24 MHz (default)

Selects HD Audio Link frequency. Applicable only if HDA codec supports selected frequency.

iDisplay Link Frequency Values: 48 MHz, 96 MHz (default)

Selects iDisplay Link frequency. Applicable only if iDisp codec supports selected frequency.

HD Audio DSP Features Configuration Submenu location: Chipset -> Platform Controller Hub (PCH) -> HD Audio Configuration -> HD Audio DSP Features Configuration

Audio DSP NHLT Endpoints Configuration:

DMIC Values: Disabled, 1 Mic Array, 2 Mic Array, 4 Mic Array (default)

Selects DMIC to expose in NHLT ACPI table

Bluetooth Values: Disabled (default), Enabled

Enables or disables Bluetooth Endpoint in NHLT ACPI table

I2S Values: Disabled (default), Enabled

Enables or disables I2S Endpoint in NHLT ACPI table

Chipset Menu


Audio DSP Feature Support:

WoV (Wake on Voice)

Bluetooth Sideband

BT Intel HFP

BT Intel A2DP

Codec based VAD

DSP based Speech. Pre-Processing Disabled


Enables/Disables DSP Feature.

Bitmask structure:

[BIT0] - WoV

[BIT1] - BT Sideband

[BIT2] - Codec based VAD

[BIT5] - BT Intel HFP

[BIT6] - BT Intel A2DP

Voice Activity Detection Values: Intel Wake on Voice (default), Windows 10 Voice Activation

Enables/Disables DSP Feature.

Bitmask structure:

[BIT0] - WoV

[BIT1] - BT Sideband

[BIT2] - Codec based VAD

[BIT5] - BT Intel HFP

[BIT6] - BT Intel A2DP

Audio DSP Pre/Post-Processing Module Support: Waves

DTS

IntelSst Speech

Dolby

ForteMedia SAMSoft

Sound Research IP

Chipset Menu


Conexant Pre-Process

Conexant Smart Amp

Custom Module 'Alpha'

Custom Module 'Beta'

Custom Module 'Gamma'


Enables/Disables 3rd Party Processing Module Support (identified by GUID). WoV must be enabled as a feature first to select relevant WoV IP.

TraceHub Configuration Menu Submenu location: Chipset -> Platform Controller Hub (PCH) -> TraceHub Configuration Menu

TraceHub Enable Mode Values: Disabled (default), Host Debugger

Select Enable, Disable or Debugger

MemRegion [0-1] Buffer Size Values: None, 1MB (default), 8MB, 64MB ,128MB ,256MB, 512MB, 1GB

Select size of mem region [0-1] buffer

DCI enable (HDCIEN) Values: Disabled (default), Enabled

When DCI is Enabled, it is taken as user consent to enable the DCI which allows debug over the USB3 interface. When Disabled, the host control is not enabling DCI feature.

DCI Auto Detect Enable Values: Disabled, Enabled (default)

When set to Auto Detect, it detects DCI being connected during BIOS post time and enables DCI. Else it disables DCI.

PCH LAN Controller Values: Enabled (default), Disabled

Enable or disable the onboard, PCH integrated ethernet controller.

Chipset Menu


DeepSx Power Policies Values: Disabled (default), Enabled in S5/Battery, Enabled in S4-S5/Battery, Enabled in S3-S4-S5/Battery, Enabled in S5, Enabled in S4-S5, Enabled in S3-S4-S5

Configure the DeepSx mode configuration.

LAN Wake From DeepSx Values: Enabled (default), Disabled

Wake from DeepSx by the assertion of LAN_WAKE# pin.

Wake on LAN Values: Enabled (default), Disabled

Enable or disable the wake on LAN capability of the onboard, PCH integrated ethernet controller.

SLP_LAN# Low on DC Power Values: Disabled, Enabled (default)

Enable or disable SLP_LAN# low on DC power.

K1 off Values: Enabled (default), Disabled

Enable or disable K1 off feature (CLKREQ).

Wake on WLAN Enable Values: Disabled (default), Enabled

Enable/Disable PCI Express Wireless LAN to wake the system.

Disable DSX ACPRESENT PullDown Values: Enabled, Disabled (default)

Disable PCH internal ACPRESENT PullDown when DeepSx or G3 exit.

Chipset Menu


Serial IRQ Mode Values: Quiet, Continuous (default)

Configure Serial IRQ Mode.

Port 61h Bit -4 Emulation Values: Disabled, Enabled (default)

Emulation of Port 61h bit-4 toggling in SMM

Port 80h Redirection Values: LPC Bus (default), PCIe Bus

Control where the port 80h cycles are sent.

Enhance Port 80h LPC Decoding Values: Disabled (default), Enabled

Support the word/dword decoding of port 80h behind LPC

Compatible Revision ID Values: Disabled (default), Enabled

Enable/Disable the PCH Compatible Revision ID feature.

PCH Cross Throttling Values: Disabled, Enabled (default)

Enable/Disable the PCH Cross Throttling feature. Only ULT support this feature.

Pcie Pll SSC Values: Auto (default), 0.0%, 0.1%, 0.2%, ..., 1.8%, 1.9%, 2.0%

Pcie Pll SSC percentage. AUTO - Keep hw default, no BIOS override. Range is 0.0%-2.0%.

Chipset Menu


Unlock PCH P2SB Values: Disabled (default), Enabled

Unlock PCH P2SB SBI and Configuration space by PSF

PMC READ DISABLE Values: Disabled, Enabled (default)

This is TEST feature for PMC XRAM read.

Platform Thermal Configuration Submenu location: Chipset -> Platform Thermal Configuration

PCH Thermal Device Values: Disabled, Enabled in PCI mode (default), Enabled in ACPI mode

Enable/Disable PCH Thermal Device(D20:F2)

PCH Temp Read Values: Disabled, Enabled (default)

PCH Temperature Read Enable

CPU Energy Read Values: Disabled, Enabled (default)

CPU Energy Read Enable

CPU Temp Read Values: Disabled, Enabled (default)

CPU Temperature Read Enable

Alert Enable Lock Values: Disabled (default), Enabled

Lock all Alert Enable settings

Chipset Menu


PCH Alert Values: Disabled (default), Enabled

PCH Alert pin enable

DIMM Alert Values: Disabled (default), Enabled

DIMM Alert pin enable


Security Menu

Security Settings If BIOS password is set, it limits access to Setup and is asked for when entering Setup. Only if BIOS password and BIOS lock are set, BIOS update & write protection can be enabled.

The password length must be in the following range:

Minimum length 3

Maximum length 20

BIOS Password Values: Type in the password

This will set the BIOS password of 3 to 20 characters. A known password can be cleared by setting a blank password.

BIOS Lock Values: Disabled, Enabled (default)

Enable/Disable the PCH BIOS Lock Enable (BLE bit) feature

HDD Security Configuration

Set User Password Allows to set, modify and clear HDD user and master passwords. User password needs to be installed for enabling security. Master password can be modified only when successfully unlocked with master password in POST. If the 'Set HDD Password' option is grayed out, do power cycle to enable the option again.

Secure Boot Menu Submenu location: Security -> Secure Boot Menu

Sample data:

System Mode Setup

Secure Boot Not Active

Vendor Keys Not Active

5

Security Menu


Secure Boot Values: Disabled, Enabled

Secure Boot can be enabled if:

1 .System running in User mode with enrolled Platform Key(PK)

2. CSM function is disabled

Secure Boot Mode Values: Standard, Custom

Secure Boot mode selector. 'Custom' Mode enables users to change Image Execution policy and manage Secure Boot Keys

Key Management Submenu location: Security -> Secure Boot Menu -> Key Management

Provision Factory Default keys


This menu option installs the factory default keys for PK, KEK, DB, DBT and DBX variables.

Enroll All Factory Default Keys

Values: Select

This menu item enrolls all factory keys from the PK, KEK, DB, DBT and DBX variables.

.

Secure Boot variable Size Key# Key source

Platform Key(PK) 0| 0|

Key Exchange Keys 0| 0|

Authorized Signatures| 0| 0|

Forbidden Signatures| 0| 0|

Authorized TimeStamps| 0| 0|

Enroll Factory Defaults or load the keys from a file with:

1. Public Key Certificate in:

a) EFI_SIGNATURE_LIST

b) EFI_CERT_X509 (DER encoded)

c) EFI_CERT_RSA2048 (bin)

d) EFI_CERT_SHA256 (bin)

Security Menu


2. Authenticated UEFI Variable

Key source:Default,Custom,Mixed


Boot Menu

Boot Configuration

Quiet Boot Values: Disabled, Enabled

The disabled option results in the normal POST messages being displayed. Enabled permits an OEM logo to appear rather that POST messages.

Setup Prompt Timeout Values: 1 (default)

This command will set the number of seconds to wait for a setup activation key.

0 results in no waiting time (not recommended), 65535 will wait indefinitely.

Bootup NumLock State Values: On, Off

This setting controls the state of the Numlock key at startup.

Power Loss Control Values: Remain Off, Turn On. Last State

Power Loss Control specifies the mode of operation if an AC power loss occurs. Remain Off keeps the power off until the power button is pressed. Turn On restores power to the computer. Last State restores the previous power state before power loss occurred.

AT Shutdown Mode Values: System Reboot, Hot S5 (default)

Determines the behaviour of an AT-powered system after a shutdown. This setting determines the behavior of AT powered systems after shutdown.

Enter Setup If No Boot Device Values: No, Yes

This setting controls having a setup menu appear when no boot devices are found.

Enable Popup Boot Menu Values: No, Yes

This command determines whether a popup boot menu appears when F11 is pressed.

6

Boot Menu


Boot Priority Selection Values: UEFI Standard, Type Based (default)

Set boot priority selection method. Type Based: Determine boot priority by device type. UEFI Standard: Determine boot priority by specific device selection. Devices must be present, priority will be changed if devices are removed or added.

Battery Support Values: Auto (Battery Manager), Battery-Only on I2C Bus, Battery-Only on SMbus

This menu item selects the battery system support. Select the “Battery-Only on I2C Bus’ option for battery-only systems using an I2C bus. Select the “Battery-Only on SMBus’ option for battery only systems using SMBus. Select “Auto” for systems equipped with a real battery system manager (connected via I2C or SMBus).

System Off Mode Values: G3/Mech Off, S5/Soft Off

System Off Mode determines the system state for battery systems after shutdown.

UEFI Fast Boot Values: Disabled, Enabled

The enabled option results in a boot with a minimal set of devices required for launch.

UEFI Screenshot Capability Values: Disabled (default), Enabled

If Enabled, you can press LCrtl+LAlt+F12 to take screenshot from current screen. It will be saved as PNG image on the first writable FAT32 partition found.

New Boot Option Policy Values: Default (default), Place First, Place Last

Controls the placement of newly detected UEFI boot options


Save & Exit Menu

Save Changes and Exit This item saves changes to the system and exits the setup menu.

Discard Changes and Exit This option exits the setup menu without saving any changes.

Save Changes and Reset This option saves changes and resets the system.

Discard Changes and Reset This option will reset the system without any changes being saved.

Save Changes Save changes made so far to any of the setup options.

Discard Changes Discard changes made so far to any of the setup options.

Default Options

Restore Defaults Restore/Load default values for all setup options.

Save as User Defaults Save the changes done so far as User Defaults.

Restore User Defaults Restore the User Defaults to all the setup options.

Generate Menu Layout File Menu layout file will be generated and stored on the first writable file system found.

7

epu-4462 4562 bios reference manual...orom ui normal delay..... 23 rst force form ..... 23...

Documents