evaluation board rev.0 for ak4370 - akm - asahi kasei ... · the akd4370 is an evaluation board for...
TRANSCRIPT
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 1 -
GENERAL DESCRIPTION
The AKD4370 is an evaluation board for 24bit DAC with Headphone Amplifier, AK4370. The AKD 4370 has the interface with AKM’s ADC evaluation boards. Therefore, it’s easy to evaluate the AK4370. The ADK4370 also has the digital audio interface and can achieve the interface with digital audio systems via opt-connector.
Ordering guide
AKD4370-B --- Evaluation board for AK4370 (Cable for connecting with printer port of IBM-AT compatible PC and control software are packed with this. This control software does not operate on Windows NT.)
FUNCTION
• Compatible with 2 types of interface - Direct interface with AKM’s A/D converter evaluation boards - On-board AK4116 as DIR which accepts optical input
• 10pin header for serial control interface • Mini-jack for external Stereo Speaker • On-board Class-D Speaker Amplifier (AK7832)
GND
AK4116(DIR)
Opt In (PORT1)
DSP 10pin Header (PORT2)
AK4370
LOUT
Regulator
Vcc (5.0V)
(3.3V)
AK7832 (SPK-Amp)
ROUT
HPL
HPR
Control Data 10pin Header (PORT3)
HP
SPPR
L/ROUT
SPPL
RIN1 RIN2LIN2LIN1
Figure 1. AKD4370 Block Diagram
* Circuit diagram and PCB layout are attached at the end of this manual.
Evaluation Board Rev.0 for AK4370AKD4370-B
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 2 -
Evaluation Board Manual
Operation sequence 1) Set up the power supply lines.
[VCC] (red) = 5.0V : for Regulator [AGND] (black) = 0V : for analog ground [DGND] (black) = 0V : for logic ground
Each supply line should be distributed from the power supply unit. 3.3V is supplied to via the regulator.
2) Set up the evaluation mode, jumper pins. (See the followings.) 3) Power on.
The AK4370 and AK4116 should be resets once bringing SW1 (DAC/DIR_PDN) “L” upon power-up. And the AK7832 should be resets once bringing SW2 (SPK_PDN) “L” upon power-up.
Evaluation mode When evaluating the AK4370 using the PORT1(AK4116), it is possible to use the initial setting of the audio interface format (24bit MSB justified). The AK4116 operates at fs of 32kHz or more. If the fs is slower than 32kHz, any other evaluation mode should be used. When inputting the data from the PORT2, the AK4370’s audio interface format should be set to correspond the input data’s audio interface format. Refer to the AK4370’s datasheet.
Applicable Evaluation Mode
(1) External Slave Mode
(1-1) Evaluation using DIR (Optical Link) of AK4116 (1-2) Evaluation connecting AKD4370 with external DSP
(2) Master Mode
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 3 -
(1) Slave Mode
The AK4370’s register should be set to Slave Mode. MCKI frequency should be set to the same as the specification of DSP or DIR. About the AK4370’s register definitions, refer to datasheet of the AK4370.
AK4370 DSP or µP
MCKI
BICK
LRCK
SDATA
BCLK
LRCK
SDTO
1fs
32fs ~ 64fs
MCLK
256fs, 384fs, 512fs,768fs or 1024fs
Figure 2. Slave Mode
(1-1) Evaluation using DIR (Optical Link) of AK4116
PORT1 (DIR) is used. Nothing should be connected to PORT2 (DSP). Set up the jumper pins.
(1-2) Evaluation connecting AKD4370 with external DSP
PORT2 (DSP) is used. Nothing should be connected to PORT1 (DIR). MCLK, SDTI, BICK, LRCK of PORT2 should be connected to MCLK, SDTO, BICK, LRCK for DSP. Set up the jumper pins.
JP4BICK2
JP3LRCK2
JP6BICK
JP7LRCKMCLK
JP5SDTOJP8
JP4BICK2
JP3LRCK2
JP6BICK
JP7LRCKMCLK
JP5SDTOJP8
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 4 -
(2) Master Mode
The AK4370’s register should be set to Master Mode. MCKI frequency should be set to the same as DSP’s specification. About the AK4370’s register definitions, refer to datasheet of the AK4370.
AK4370 DSP or µP
MCKI
BICK
LRCK
SDATA
BCLK
LRCK
SDTO
1fs
32fs, 64fs
MCLK
256fs, 384fs, 512fs,768fs or 1024fs
Figure 3. Master Mode
PORT2 (DSP) is used. Nothing should be connected to PORT1 (DIR). The system clock should be connected to MCLK of PORT2. SDTI of PORT2 should be connected to SDTO of DSP. The JP4(LRCK2) and JP3(BICK2)’s right side should be connected to LRCK and BICK of DSP. Set up the jumper pins.
JP4BICK2
JP3LRCK2
JP6BICK
JP7LRCKMCLK
JP5SDTOJP8
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 5 -
Other jumper pins set up
JP1 (GND) : Analog ground and Digital ground. OPEN : Separated. SHORT : Common. <default> JP11 (INLN) : Setting of AK7832 Input pin “INLN” OPEN : When SW2 (SPK_PDN) is “L”. SHORT : When SW2 (SPK_PDN) is “H”. <default> JP12 (INRN) : Setting of AK7832 Input pin “INRN” OPEN : When SW2 (SPK_PDN) is “L”. SHORT : When SW2 (SPK_PDN) is “H”. <default> JP13 (DVDD_REG) : Setting of Power Supply “DVDD” OPEN : It supplies “DVDD” from the outside. SHORT : It supplies “DVDD” from the Regulator (3.3V).<default>
The function of the toggle SW
Upper-side is “H” and lower-side is “L”.
[SW1] (DAC/DIR_PDN): Power down of AK4370 and AK4116. Keep “H” during normal operation.
[SW2] (SPK_PDN): Power down of AK7832. Keep “H” during normal operation. Indication for LED
[LED1] (ERF): Monitor INT0 pin of the AK4116. LED turns on when some error has occurred to AK4116.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 6 -
Serial Control
The AK4370 can be controlled via the printer port (parallel port) of IBM-AT compatible PC. Connect PORT3 (uP -IF) with PC by 10 wire flat cable packed with the AKD4370.
10pin Header
CSN
10 Wire Flat Cable
CCLK
CDTI
10pin Connector
PC
Connect
AKD4370
Figure 4. Connect of 10 wire flat cable
(1) 3-wire Serial Control Mode <Default>
The jumper pins should be set to the followings.
(2) I2C-bus Control Mode
The jumper pins should be set to the followings.
(2-1) In case of using CAD0=0 (device address bits).
(2-2) In case of using CAD0=1 (device address bits).
JP2I2C_SEL
JP9SDA
I2C 3-wire
JP10CAD0
JP2I2C_SEL
JP9SDA
I2C 3-wire
JP10CAD0
JP2I2C_SEL
JP9SDA
I2C 3-wire
JP10CAD0
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 7 -
Input / Output circuit (1) Input Circuit
LIN1/RIN1, LIN2/RIN2 Input circuits
+C201u
+C191u
6
43
J3LIN2/RIN2
+C271u
+C211u
LIN2
RIN2
LIN1
RIN16
43
J2LIN1/RIN1
Figure 5. LIN1/RIN1,LIN2/RIN2 Input circuits
(2) Output Circuit 1) HPL/HPR Output Circuit
+
C25100u
6
43
J4
HP
+
C28100u
R9 (short)HPR
HPLR10(short)
Figure 6. HPL/HPR Output Circuit
2) LOUT/ROUT Output Circuit
+
C301u
6
43
J6
L/R OUT
R1247k
R11220
+
C321u
R1447k
R13220
LOUT
ROUT
Figure 7. LOUT/ROUT Output Circuit
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 8 -
3) Speaker Output Circuit
Evaluation using AK7832’s Speaker , the jumper pins should be set to the followings.
6
43
J8
SPP_R
6
43
J7
SPP_L
VCRN
VCRP
VCLP
VCLN1
TP3VCLP
1
TP2VCLN
1
TP4VCRN
1
TP5VCRP
Figure 8. SPK-Amp Output Circuit
∗ AKM assumes no responsibility for the trouble when using the above circuit examples.
JP12INRN
JP11INLN
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 9 -
Control Software Manual
Set-up of evaluation board and control software
1. Set up the AKD4370 according to previous term.
2. Connect IBM-AT compatible PC with AKD4370 by 10-line type flat cable (packed with AKD4370). Take care of
the direction of 10pin header. (Please install the driver in the CD-ROM when this control software is used on Windows 2000/XP. Please refer “Installation Manual of Control Software Driver by AKM device control software”. In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows NT.)
3. Insert the CD-ROM labeled “AK4370 Evaluation Kit” into the CD-ROM drive.
4. Access the CD-ROM drive and double-click the icon of “akd4370.exe” to set up the control program.
5. Then please evaluate according to the follows.
Operation flow
Keep the following flow.
1. Set up the control program according to explanation above. 2. Click “Port Reset” button. 3. Click “Write default” button
Explanation of each buttons
1. [Port Reset] : Set up the USB interface board (AKDUSBIF-A) when using the board. 2. [Write default] : Initialize the register of AK4370. 3. [All Write] : Write all registers that is currently displayed. 4. [Function1] : Dialog to write data by keyboard operation. 5. [Function2] : Dialog to write data by keyboard operation. 6. [Function3] : The sequence of register setting can be set and executed. 7. [Function4] : The sequence that is created on [Function3] can be assigned to buttons and executed. 8. [Function5] : The register setting that is created by [SAVE] function on main window can be assigned to
buttons and executed. 9. [SAVE] : Save the current register setting. 10. [OPEN] : Write the saved values to all register. 11. [Write] : Dialog to write data by mouse operation.
Indication of data
Input data is indicated on the register map. Red letter indicates “H” or “1” and blue one indicates “L” or “0”. Blank is the part that is not defined in the datasheet.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 10 -
Explanation of each dialog 1. [Write Dialog]: Dialog to write data by mouse operation
There are dialogs corresponding to each register. Click the [Write] button corresponding to each register to set up the dialog. If you check the check box, data becomes “H” or “1”. If not, “L” or “0”.
If you want to write the input data to AK4370, click [OK] button. If not, click [Cancel] button. 2. [Function1 Dialog] : Dialog to write data by keyboard operation Address Box: Input registers address in 2 figures of hexadecimal. Data Box: Input registers data in 2 figures of hexadecimal.
If you want to write the input data to AK4370, click [OK] button. If not, click [Cancel] button. 3. [Function2 Dialog] : Dialog to evaluate DATT
There are dialogs corresponding to register of 05h, 06h, 09h and 0Eh. Address Box: Input registers address in 2 figures of hexadecimal. Start Data Box: Input starts data in 2 figures of hexadecimal. End Data Box: Input end data in 2 figures of hexadecimal. Interval Box: Data is written to AK4370 by this interval. Step Box: Data changes by this step. Mode Select Box:
If you check this check box, data reaches end data, and returns to start data. [Example] Start Data = 00, End Data = 09
Data flow: 00 01 02 03 04 05 06 07 08 09 09 08 07 06 05 04 03 02 01 00
If you do not check this check box, data reaches end data, but does not return to start data. [Example] Start Data = 00, End Data = 09
Data flow: 00 01 02 03 04 05 06 07 08 09
If you want to write the input data to AK4370, click [OK] button. If not, click [Cancel] button.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 11 -
4. [SAVE] and [OPEN]
4-1. [SAVE]
All of current register setting values displayed on the main window are saved to the file. The extension of file name is “akr”.
<Operation flow> (1) Click [SAVE] Button. (2) Set the file name and click [SAVE] Button. The extension of file name is “akr”.
4-2. [OPEN]
The register setting values saved by [SAVE] are written to the AK4370. The file type is the same as [SAVE].
<Operation flow> (1) Click [OPEN] Button. (2) Select the file (*.akr) and Click [OPEN] Button.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 12 -
5. [Function3 Dialog]
The sequence of register setting can be set and executed. (1) Click [F3] Button. The default setting sequence DAC->HP(3D=OFF) is displayed. Jump to (3) below if the
default setting sequence is used. Go to (2) if the other setting sequence is required. (2) Set the control sequence.
Set the address, Data and Interval time. Set “-1” to the address of the step where the sequence should be paused. (3) Click [START] button. Then this sequence is executed. The sequence is paused at the step of Interval="-1". Click [START] button, the sequence restarts from the paused step. This sequence can be saved and opened by [SAVE] and [OPEN] button on the Function3 window. The extension of file name is “aks”.
Figure 9. Window of [F3]
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 13 -
6. [Function4 Dialog]
The sequence file (*.aks) saved by [Function3] can be listed up to 10 files, assigned to buttons and then executed. When [F4] button is clicked, the window as shown in Figure 9 opens.
Figure 10. [F4] window
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 14 -
6-1. [OPEN] buttons on left side and [START] buttons
(1) Click [OPEN] button and select the sequence file (*.aks) saved by [Function3].
The sequence file name is displayed as shown in Figure 10. ( In case that the selected sequence file name is “DAC_Stereo_ON.aks”)
Figure 11. [F4] window (2)
(2) Click [START] button, then the sequence is executed.
6-2. [SAVE] and [OPEN] buttons on right side
[SAVE] : The name assign of sequence file displayed on [Function4] window can be saved to the file. The file name is “*.ak4”.
[OPEN] : The name assign of sequence file(*.ak4) saved by [SAVE] is loaded.
6-3. Note
(1) This function doesn't support the pause function of sequence function. (2) All files used by [SAVE] and [OPEN] function on right side need to be in the same folder. (3) When the sequence is changed in [Function3], the sequence file (*.aks) should be loaded again in order to reflect
the change.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 15 -
7. [Function5 Dialog]
The register setting file(*.akr) saved by [SAVE] function on main window can be listed up to 10 files, assigned to buttons and then executed. When [F5] button is clicked, the window as shown in Figure 11 opens.
Figure 12. [F5] window
7-1. [OPEN] buttons on left side and [WRITE] button
(1) Click [OPEN] button and select the register setting file (*.akr).
The register setting file name is displayed as shown in Figure 12. (In case that the selected file name is “DAC_Output.akr”)
(2) Click [WRITE] button, then the register setting is executed.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 16 -
Figure 13. [F5] window (2)
7-2. [SAVE] and [OPEN] buttons on right side
[SAVE] : The name assign of register setting file displayed on [Function5] window can be saved to the file. The file name is “*.ak5”.
[OPEN] : The name assign of register setting file(*.ak5) saved by [SAVE] is loaded. 7-3. Note
(1) All files used by [SAVE] and [OPEN] function on right side need to be in the same folder. (2) When the register setting is changed by [SAVE] Button on the main window, the register setting file (*.akr)
should be loaded again in order to reflect the change.
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 17 -
MEASUREMENT RESULTS
[Measurement condition]
• Measurement unit : Audio Precession System Two Cascade • MCLK : 11.2896MHz • BICK : 64fs • fs : 44.1kHz • Bit : 24bit • Measurement Mode : Slave Mode • Power Supply : AVDD = HVDD = DVDD = PVDD = 3.3V • Measurement Filter :22Hz ∼ 20kHz • Temperature : Room
Parameter DAC Analog Output Characteristics Result (Lch / Rch) Unit DAC -> HP AMP RL=16Ω THD+N (0dBFS Output) 54.1 / 54.2 dB D-Range (-60dB Output, A-weighted) 92.7 / 92.7 dB S/N (A-weighted) 93.2 / 93.2 dB DAC -> LOUT RL=47kΩ THD+N (0dBFS Output) 59.8 / 60.0 dB D-Range (-60dB Output, A-weighted) 90.2 / 90.2 dB S/N (A-weighted) 90.4 / 90.2 dB
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 18 -
[Plot of Headphone Amp] AKM HP-AMP THD + N vs Input Level
fs=44.1kHz , fin=1kHz
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
-120 +0-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10dBFS
Figure 14. THD+N vs. Input Level
AKM HP-AMP THD + N vs Input Frequency
fs=44.1kHz , 0dB Input
-140
+0
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
20 20k50 100 200 500 1k 2k 5k 10kHz
Figure 15. THD+N vs. Input Frequency
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 19 -
AKM HP-AMP THD + N vs Linearity
fs=44.1kHz , fin=1kHz
-120
+0
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
-120 +0-110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10dBFS
Figure 16. Linearity
AKM HP-AMP Frequency Response
fs=44.1kHz , 0dB Input
-24
+2
-22
-20
-18
-16
-14
-12
-10
-8
-6
-4
-2
-0
dBr A
20 20k50 100 200 500 1k 2k 5k 10kHz
Figure 17. Frequency Response
(including external HPF)
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 20 -
AKM HP-AMP FFT
fs=44.1kHz , 0dB Input
-180
+0
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
20 20k50 100 200 500 1k 2k 5k 10kHz
Figure 18. FFT Plot(1kHz,0dB)
AKM HP-AMP FFT
fs=44.1kHz , -60dB Input
-180
+0
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
20 20k50 100 200 500 1k 2k 5k 10kHz
Figure 19. FFT Plot(1kHz,-60dB)
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 21 -
AKM HP-AMP FFT fs=44.1kHz , No Signal
-180
+0
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
20 20k50 100 200 500 1k 2k 5k 10kHz
Figure 20. FFT Plot(Noise Floor)
AKM HP-AMP FFTfs=44.1kHz , Outband Noise
-180
+0
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dBr A
20 100k50 100 200 500 1k 2k 5k 10k 20k 50kHz
Figure 21. Out-band Noise
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 22 -
AKM HP-AMP Crosstalk
fs=44.1kHz , 0dB Input
-120
+0
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
dB
20 20k50 100 200 500 1k 2k 5k 10kHz
Figure 22. Crosstalk
ASAHI KASEI [AKD4370-A]
<KM086300> 2006/12 - 23 -
Date (YY/MM/DD)
Manual Revision
Board Revision
Reason Contents
06/12/12 KM086300 0 First edition
Revision History
IMPORTANT NOTICE
• These products and their specifications are subject to change without notice. Before considering
any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status.
• AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein.
• Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials.
• AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance
of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property.
(b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability.
• It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification.
A
A
B
B
C
C
D
D
E
E
E E
D D
C C
B B
A A
LIN
1
LIN
2
CC
LK
CS
N
HPR
PD
N
DVDD
HPL
AVDD_REG
HVDD_REG
RIN
2
RIN
1
MCKI
LRCK
BICK
SDATA
CD
TI
D_REG
VCLP
VCLN
VCRP
VCRN
SPK_PDN
LOUT
ROUT
Title
Size Document Number Rev
Date: Sheet of
AK4370 , AK7832 0
AKD4370-B
A3
1 3Monday, October 30, 2006
Title
Size Document Number Rev
Date: Sheet of
AK4370 , AK7832 0
AKD4370-B
A3
1 3Monday, October 30, 2006
Title
Size Document Number Rev
Date: Sheet of
AK4370 , AK7832 0
AKD4370-B
A3
1 3Monday, October 30, 2006
DGND AGND
AK7832
JP11INLNJP11INLN
R4 51R4 51
R751R751
+C810u+C810u
JP12INRNJP12INRN
+C210u +C210u
JP1GNDJP1GND
C10.1uC10.1u
C16
0.01u
C16
0.01u
+C62.2u
+C62.2u
R3 51R3 51
R847kR847k
C30.1uC30.1u
C90.1uC90.1u
PDNC3
SDAC2
DVDDIC1
VCB5
VSS3B4
INLPB3 INR
PB
2
SC
LB
1
NC
A5
INLN
A3
INR
NA
2
NC
A1
NC E5
VCLP E4
VSS1 E3
VCRP E2
NC E1
VDD1 D5
VC
LND
4
VS
S2
D3
VC
RN
D2
VD
D2
D1
VD
D3
C5
I2C
EN
C4
U2U2
R5 10R5 10
+C410u +C410u
C150.1uC150.1u
R1 51R1 51
R2 51R2 51
JP2
I2C_SEL
JP2
I2C_SEL
C50.1uC50.1u
+ C141u
+ C141u
C170.1uC170.1u
C130.1uC130.1u
SDATA1
BICK2
LRCK3
MCKI4
DVDD5
VSS26
CD
TI/S
DA
7
CS
N/C
AD
09
PD
N10
I2C
11
MU
TET
12
LOUT 13
ROUT 14
VCOM 15
AVDD 16
HVDD 17
HP
L20
RIN
221
LIN
222
RIN
123
LIN
124
CC
LK/S
CL
8
VSS1 18
HP
R19U1
AK4370VN
U1
AK4370VN
A
A
B
B
C
C
D
D
E
E
E E
D D
C C
B B
A A
VCC +5V
VCRN
VCRP
VCLN
VCLP
LIN2
RIN2
LIN1
RIN1 HPR
HPL
LOUT
ROUT
DIR_REG
D_REG
AVDD_REG
HVDD_REG
DVDD
Title
Size Document Number Rev
Date: Sheet of
Input/Output 0
AKD4370-B A3
2 3Monday, October 30, 2006
Title
Size Document Number Rev
Date: Sheet of
Input/Output 0
AKD4370-B A3
2 3Monday, October 30, 2006
Title
Size Document Number Rev
Date: Sheet of
Input/Output 0
AKD4370-B A3
2 3Monday, October 30, 2006
6
43
J7
SPP_L
J7
SPP_L
1 2L1 10uL1 10u
IN OUT
GN
D
T1TA48M33FT1TA48M33F
+C211u +C211u
+
C28100u+
C28100u
+C201u +C201u
R11220R11220
C240.1uC240.1u
+
C25100u+
C25100u
R1447kR1447k
+C191u +C191u
+
C321u+
C321u
1 2L2 (short)L2 (short)
JP13
DVDD_REG
JP13
DVDD_REG R1247kR1247k
6
43
J3LIN2/RIN2J3LIN2/RIN2
1
TP4VCRNTP4VCRN
+ C2247u
+ C2247u
6
43
J2LIN1/RIN1J2LIN1/RIN1
1
TP3VCLPTP3VCLP
1 2L3 (short)L3 (short)
6
43
J4
HP
J4
HP
+ C2647u
+ C2647u
+
C301u+
C301u
R9 (short)R9 (short)
1
TP2VCLNTP2VCLN
6
43
J8
SPP_R
J8
SPP_R
R10(short)R10(short)
6
43
J6
L/R OUT
J6
L/R OUT
1
TP5VCRPTP5VCRP
C230.1uC230.1u
1 2L4 (short)L4 (short)
R13220R13220
+C271u +C271u
A
A
B
B
C
C
D
D
E
E
E E
D D
C C
B B
A A
GNDGND
DIR_REG CSN
CCLK
CDTI
CDTO
D_REGD_REG
DIR_REG
CDTI
CCLK
CSN
MCKI
SDATA
LRCK
BICK
PDN
D_REG
CDTO
D_REG
SPK_PDN
PDN
D_REG DVDD
Title
Size Document Number Rev
Date: Sheet of
CLOCK 0
AKD4370-BA2
3 3Thursday, November 16, 2006
Title
Size Document Number Rev
Date: Sheet of
CLOCK 0
AKD4370-BA2
3 3Thursday, November 16, 2006
Title
Size Document Number Rev
Date: Sheet of
CLOCK 0
AKD4370-BA2
3 3Thursday, November 16, 2006
uP-I/F
CSNSCL/CCLKSDA/CDTI
SDTI
MCLK
LRCKBICK
CDTO
L HL H
R21 10kR21 10k
1A11Y22A32Y43A53Y6
Vcc14
GND7
4Y 84A 95Y 105A 116Y 126A 13
U3 74HC14U3 74HC14
C410.1uC410.1u
JP10CAD0JP10CAD0
12
X111.2896MHz
X111.2896MHz
213
SW2SPK_PDNSW2SPK_PDN
R1912kR1912k
R205.1R205.1
R26 470R26 470
R151k
R151k
OUT 1
VCC 3
GND 2
PORT1
TORX141
PORT1
TORX141
R24 470R24 470
C440.1uC440.1u
A13
A24
A46
A57
A68
A79
A810
OE 22
B1 21
B2 20
B3 19
B4 18
B5 17
B6 16
B7 15
B8 14
VCCB 24
GND 13
A35
DIR2 VCCB 23
VCCA1
GND11
GND12
U5
74AVC8T245
U5
74AVC8T245
C340.1uC340.1u
C4310p
C4310p
R23 10kR23 10k
12
L547uL547u
12345 6
78910
PORT3PORT3
+C4010u+C4010u
JP7
LRCK
JP7
LRCK
R25 10kR25 10k
KA
LED1ERFLED1ERF
R18470R18470
R1610kR1610k
C390.1uC390.1u
KA
D2HSU119D2HSU119
C370.1uC370.1u
213
SW1DAC/DIR_PDNSW1DAC/DIR_PDN
RX01
DVDD2
DVSS3
XTI4
XTO5
LRC
K6
BIC
K7
SD
TO8
DA
UX
9
MC
KO
10
CDTO 11
CDTI 12
CCLK 13
CSN 14
INT1 15
INT0
16
PD
N17
AV
SS
18
R19
AV
DD
20U4
AK4116
U4
AK4116
C330.1uC330.1u
1
TP6XTITP6XTI
C380.1uC380.1u
+
C3610u
+
C3610u
C450.1uC450.1u
JP4BICK2
JP4BICK2
12345 6
78910
PORT2
DSP
PORT2
DSP
R22 470R22 470
JP3LRCK2
JP3LRCK2
R2710kR2710k
KA
D1HSU119D1HSU119
JP9SDAJP9SDA
JP6
BICK
JP6
BICK
JP8
SDTO
JP8
SDTO
R1710kR1710k
JP5
MCLK
JP5
MCLK
C350.1uC350.1u
C4210p
C4210p