feroof roof tile installation (veneto2 , rio , rio ez , wood , diva , zissen , slate)_rev.3
DESCRIPTION
FEROOF ROOF Tile Installation (Veneto2 , Rio , Rio EZ , Wood , Diva , Zissen , Slate)_Rev.3TRANSCRIPT
2
Veneto 2Slate
1
2
1,345mm25mm
370mm
1,345mm
1,335mm
25mm
25mm
370mm
370mm
- Overrall length : 1,345mm (±5mm)- length of cover : 1,280mm
- With of cover : 370mm
- Upstand : 25mm
- Roof cover/Tile : 0.473㎡- Tiles : 2.11/㎡- Weight/Tile : 2.6~2.7kg
1,345mm25mm
370mm
- Overrall length : 1,345mm (±5mm)- length of cover : 1,280mm
- With of cover : 370mm
- Upstand : 25mm
- Roof cover/Tile : 0.473㎡- Tiles : 2.11/㎡- Weight/Tile : 2.6~2.7kg
- Overrall length : 1,345mm (±5mm)- length of cover : 1,280mm
- With of cover : 370mm
- Upstand : 25mm
- Roof cover/Tile : 0.473㎡- Tiles : 2.11/㎡- Weight/Tile : 2.6~2.7kg
- Overrall length : 1,335mm (±5mm)- length of cover : 1,280mm
- With of cover : 370mm
- Upstand : 25mm
- Roof cover/Tile : 0.473㎡- Tiles : 2.11/㎡- Weight/Tile : 2.55~2.65kg
1 . Rio Specifications
Rio EZ Specifications
Diva Specifications
Wood Specifications
3
1,365mm25mm
370mm
300mm450mm
300mm
320mm320mm
320mm320mm
- Overrall length : 1,365mm (±5mm)- length of cover : 1,280mm
- With of cover : 370mm
- Upstand : 25mm
- Roof cover/Tile : 0.473㎡- Tiles : 2.11/㎡- Weight/Tile : 2.6~2.7kg
- Warning : Avoid nailing in places with electrical wiring above or below.
- Roof : For each square meter of roof tile, use 1kg of fastener.
When you drive a fastener, fastener up in the
first point of upcurve as marked in red.
(There's a risk of water damage when you
drive a fastener on downcurve.)
2 . Nailing Position
Zissen Specifications
Veneto 2 Specifications
380mm
1,285mm25mm- Overrall length : 1,285mm (±5mm)- length of cover : 1,215mm
- With of cover : 380mm
- Upstand : 25mm
- Roof cover/Tile : 0.4617㎡- Tiles : 2.17/㎡- Weight/Tile : 2.5~2.6kg
1,340mm20mm
370mm
- Overrall length : 1,340mm (±5mm)- length of cover : 1,290mm
- With of cover : 370mm
- Upstand : 20mm
- Roof cover/Tile : 0.473㎡- Tiles : 2.11/㎡- Weight/Tile : 2.6~2.7kg
SLATE Specifications
4
3 . Auxiliary
- Half round ridge/hip - V-Ridge/hip
Manufacture with other measurements.
Ridge/hip
overall length 400mm
length of cover 370mm
Ridge/hip cap
Side flashing
overall length 1,340mm
length of cover 1,300mm
Shackle
overall length 970mm
height 55.8mm
RG-Ridge/hip , V-Ridge
overall length 1,340mm
length of cover 1,300mm
- RG-Ridge/hip - V-Ridge
Barge board flashing
overall length 1,340mm
length of cover 1,300mm
Fascia flashing
overall length 1,340mm
length of cover 1,300mm
Flat sheet
overall length 1,340mm (±5mm)
Angle
overall length 120mm
Nail
- Screw Nail : 5cm
- Galvanized or heat-plated
Closer
overall length 970mm
height 34.8mm
Valley
overall length 1340mm
92mm
400mm140mm
94mm
150mm
400mm
110mm
160mm
160mm
180mm
145mm
- V-Ridge/hip Cap - Half round Ridge/hip Cap
12mm
30mm
1,340㎜
92㎜
40㎜
20㎜
92mm
40mm20mm
1,340mm
160mm
1,340mm
12mm
50mm65mm
15˚
12mm
12mm
12mm
- Screw Bolt : 3cm / 5cm
- Galvanized or heat-plated
5
Closer
overall length 970mm
height 34.8mm
Screw Nail:50mm- While pounding in fasteners, always face the
eaves while standing on top of the tiles being installed.
- Use 6~8 fasteners for each roof tile.
- In high-wind or coastal regions, use 10 fasteners per tile.
- After nailing, in order to prevent water damage, always use A/S adhesive to finish installation.
Batten Type
Battenless Type
Fasteners for panels: No. 8 x 1 ½” hex head screws or
No. 9 x 1 ½” hex head screws or
1 ½” to 2 ½” ring fasteners. (8d)
Fasteners for rafters: No. 10 x 3 ½” hex head screws or
3 ½” ring fasteners. (16d)
Fasteners for batten
==> same fasteners without/with battens
==> screw bolt
==> lenght = 50mm or longer
==> diameter= 5mm
4 . Nailing Technique
5 . Roof Tile Spacing
- The auxiliary pieces listed above can be custom-made to your measurements.
- Storage method : Always cover with a waterproof material.
- Packing : One pallet is 1.35m × 95m × 1.2m.
- pitch : The roof must be at least 15 degrees.
- in coastal or high-wind areas, use 9-layer galvanized or zinc-coated plates.
When installing gutter When installing fascia flashing
350mm 350mm365mm 365mm365mm 365mm365mm 365mm
Space roof tile 365mm apart. Space roof tile 365mm apart.
Screw Bolt
50mm
30mm
6
6 . The way how to install roof tile on concrete or wooden roof frame
AHF
C ED
B
G
A. Ridge and Ridge Boards
Wooden roof frame
Half Round Ridge/Hip 400mm
nail position
When installing Half Round Ridge/Hip 400mm
When installing RG-Ridge/Hip 1,340mm
Concrete roof frame
nail position
Half Round Ridge/Hip 400mm
Concrete roof frame
nail position
RG-Ridge/Hip 1,340mm
Wooden roof frame
nail position
RG-Ridge/Hip 1,340mm
7
300mm450mm
300mm
320mm320mm
320mm320mm
B. Ridge and - Finish
When installing Half Round Ridge/Hip 400mm When installing V-Ridge 1,340mm
- Finish with the end part with Half Round
Ridge/Hip Cap.
- Finish with the end part with V-Ridge/Hip
Cap.
When installing RG-Ridge/Hip 1,340mm
Cut Fold
Install nailing through each side
1-1 1-2
C-1. Install Rio, Rio EZ, Wood, Diva, Zissen, Slate as space
- Space each sheet of Rio, Rio EZ
Wood, Diva, Zissen, Slate 365mm apart.
Roof Tile
ConcreteBatten (38mm×38mm)
RAFTER (38mm x 235mm)
350mm
365mm
365mm
Nailing position
Screw
Nail:50mm
Slate Nailing position
8
500mm500mm
300mm250mm
250mm
440mm
C-2. Install Veneto 2 as space
- Space each sheet of Veneto 2
380mm apart.
Roof Tile
ConcreteRAFTER (38mm x 235mm)
Batten (38mm×38mm)
360mm
380mm
380mm
Nailing position
Screw Nail:50mm
Fasteners
Concrete roof frameWooden roof frameAngle
Batten (38×38) Batten (38×38)
Roof Tile Roof Tile
Tile B overlaps tile A(Overlap)
(Lower part)
End of adjacent tile(End of tile)
(Nail)(Lower part) (Nail)
Tile B overlaps tile A(Overlap)
Stitch Screw DIVA Only
Stitch Screw VENETO 2 Only
End of adjacent tile(End of tile)
A AB B
(Lower part)(Nail)
Tile B overlaps tile A(Overlap)
End of adjacent tile(End of tile)
A B(Nail)
Tile B overlaps tile A(Overlap)
Stitch Screw SLATE Only
End of adjacent tile(End of tile)
A B
9
Nail NailNail
D. Fascia flashing
When installing gutter system When installing fascia flashing When installing fascia+gutter flashing
Change of the Pitch
365mm
365mm
365mm365mm
concrete
batten
Lay one roof tile on another in tiers from eaves of roof.
②①
10
G. Barge boards
When using side flashing, install the batten above the rafter and match the top of the barge board
to the top of the batten.
the edge of the steel roof tiles must be bent so that the part tucked into the side flashing is long
enough to prevent water damage.
Roof tile
Barge board
Barge board flashing
E. Dutch gables
F. Junctions with vertical faces
Insert the top edge of the roof tile or a piece of sheet metal inside the side flashing.
Sealanter
Side flashing
Roof Tile Roof Tile
Gutter
Sealanter
In the case of a side of roof tile at the boundary with vertical wall, connect roof tile with vertical
wall and finish vertical wall with Side Flashing.
If there's a valley in which water flows at the boundary with vertical wall, install gutter.
11
H. Valleys
In the case of Rio, Rio EZ, Diva, Wood, Zissen, Veneto 2, Slate roof, finish valley with not valley
flashing but bent flat sheet.
Roof Tile
- 1) Valleys
- 2) Roof Tile
Roof Tile
Roof Tile
Roof Tile
Finished tile line
Batten
Batten
Batten
Valley
Valley
Valley
Valley
Screw Neil
Screw Neil
Batten
ValleyConcrete
Screw Neil
7 . Side ViewV-Cutting and
Silicon Caulking
Feroof Tile
Rafter
Batten
Feroof Tile
Fascia flashing
Barge Board
Flashing
RafterBatten
Screw Nail:50mm
12
8. The way how to install roof tile on Sandwich panel roof frame
※ No. 1
※ Side View of Sandwich
※ Detailed View
Sandwich panel 100mm
Sandwich panel 100mm
C-Channel steel frame
C-Channel steel frame
※ Chimney Area
Feroof Tile
Silicon Caulking
Flashing
Concrete
※ Window Area
Batten
Feroof Tile
Silicon Caulking
Window
Concrete Mortar
Finish
Flashing
13
※ No. 2
Ridge
Batten
Batten
Feroof Tile
Screw Bolt 75mm
Screw Bolt 75mm
Sandwich panel 100mm
Sandwich panel 100mm
Fascia flashing
C-Channel steel frame
C-Channel steel frame
Detailed View of Fascia flashing
"Fix the Batten as Screw Bolt (75mm)"
※ Side View of Sandwich
※ Detailed View
14
9 . Batten Installation- Batten Installation for Concrete Roof
1) Fasten one Batten in the part of ridge
3) In the Case of Uneven Roof Surface.
5)
2)
4)
Cross the rafer
Concrete
Batten38×38
800mm800mm
Cutting Section
Concrete
AngleBatten38×38
Rafter
RafterBatten38×38
350mm
(veneto2360mm)
(veneto2380mm)
(veneto2380mm)
365mm
365mm
15
2)
4)
Cross the rafer
Cutting
Section
Rafter
- Batten Installation for Wooden Roof
Wooden Roof Wooden Roof
Wooden Roof
350mm
365mm
365mm
Batten38×38
Batten38×38
1)
3)
(veneto2360mm)
(veneto2380mm)
(veneto2380mm)
/ Rev : 3 ( 2013. 08. 21 )