gas flow meter product guide
TRANSCRIPT
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 1/8
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 2/8
Capable of measuring ow onpiping systems from 3/4” to 2”
Quick and simple repair, nospecial tools required
Operating Principle
Threaded StyleGT Series Gas Turbine
The Kimray ¾” – 2” Cartridge Style GT Series Gas Turbine Meter is a
unique one-piece cartridge design which has been adapted to include
a gas rotor and bearing assembly. Each meter has three separate
rotor designs which overlap adjacent meter ranges and will conform
to more pipe sizes without reduction or expansion requirements.
Covering ow rates from 0.5 to 200 ACFM, these meters will work
within pressures from vacuum to 2000 psi. Replacement cartridges
are fully-calibrated and are ready for installation with no special tools
required.
Kimray’s Tungsten Carbide V-Cup bearing design provides excellent
performance and unequalled service life in non-lubricating and solids
containment gases.
As gas ows into the turbine, it causes the turbine to rotate at a speed
proportional to the actual velocity of gaseous materials owing. As
each turbine blade passes through the magnetic eld at the base of the
transducer, an AC voltage pulse is generated in the pickup coil. These
pulses produce an output frequency proportional to the volumetric ow
through the meter.
Introduction
Accurate (±1% of reading) andreliable (repeatability ±0.25%) ow
measurement solution from .13 ACFMto 200 ACFM
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 3/8k i m r a y . c o m
Materials of Construction:
Body; 316 L Stainless Steel
Flanges; 316 Stainless Steel
Rotor; 431 Stainless Steel
Rotor Shaft; Tungsten Carbide
Flow Linearity: ±1% of reading
Repeatability: ± 0.25%
Frequency Output: 100 to 1,100 Hz
Voltage Output: Approximately 100mV @ 100 Hzto 1.5 V (RMS) @ 1,000 Hz
Pressure Rating: 5,000 psi (maximum)
Pressure Drop: 0.5 psi at 100% of ow range
Turbine Temperature: -20 °F to +300 °F
(-29 °C to 149 °C)
Extended Temperature: -200 °F to +450 °F
(-130 °C to 218 °C)
Specifcations
It is recommended that at least one spare Internal Parts Kit be kept fo
each size and ow range of gas meter. This will provide a calibrated
replacement should a problem develop with the meter in service. This
avoids costly delays associated with even a short down time. The
internal parts kits include a calibrated gas cartridge and a new spira
lock ring.
Repair Kits
GT Series Meters, Repair Kits, & Accessories
Threaded End Meters
Part Number Meter Size End ConnectionEnd to
End
Flow
ACFM
Ranges
ACFH
Nom. K-Factor
P/ACF
GT Repair Kit
Part Number
KSIGT3/0750L 3/4” 3/4” Male NPT 3.4” .13-1.3 8-80 44,000 KSI81014600
KSIGT3/0750M 3/4” 3/4” Male NPT 3.4” .5-5.0 30-300 12,200 KSI81034600
KSIGT3/0750H 3/4” 3/4” Male NPT 3.4” .75-7.5 45-450 8,000 KSI81054600
KSIGT3/1000L 1” 1” Male NPT 3.6” .5-5.0 30-300 13,000 KSI81014601
KSIGT3/1000M 1” 1” Male NPT 3.6” .65-6.5 40-400 9,000 KSI81034601
KSIGT3/1000H 1” 1” Male NPT 3.6” 1.1-11 65-650 5,600 KSI81054601KSIGT3/1500L 1-1/2” 1-1/2” Male NPT 4.7” .6-6.0 36-360 10,000 KSI81014602
KSIGT3/1500M 1-1/2” 1-1/2” Male NPT 4.7” 1.65-16.5 100-1000 3,600 KSI81034602
KSIGT3/1500H 1-1/2” 1-1/2” Male NPT 4 .7” 3.0-30 175-1750 2,100 KSI81054602
KSIGT3/2000L 2” 2” Male NPT 6.0” 3.0-30 1 75-1750 2,100 KSI81014603
KSIGT3/2000M 2” 2” Male NPT 6.0” 4.5-45 2 75-2750 1,300 KSI81034603
KSIGT3/2000H 2” 2” Male NPT 6.0” 8.5-85 500-5000 720 KSI81054603
KSIGT3/2000XH 2” 2” Male NPT 6.0” 20-200 1200-12000 300 KSI81154603
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 4/8
Unique “between-the-ange”design eliminates need for
mating anges
Quick and simple repair, nospecial tools required
Introduction
Operating Principle
Wafer Style
The Wafer style in-line turbine ow meter was developed for
applications where accuracy and dependability are of concern to
the operator. The wafer style’s stainless steel body incorporates a
helical turbine with tungsten carbide shaft and bearings. It provides
an efcient, long service life and a cost-effective solution for your
measurement requirements.
Simple in design and construction, Its between-the-ange design
eliminates the need for mating anges, requiring less space in the
ow line, lowering costs and providing easy, one-man installation.
The meter produces a sine-wave signal proportional to its volumetric
ow rate. With optional Kimray electronics, the wafer style provides
local ow rate and volume totalization and will interface with most
instruments, PLCs and computers.
Gas passes through the turbine, causing the turbine to rotate at a
speed proportional to uid velocity. As each turbine blade passes
through the magnetic eld generated by the meter’s magnetic pick
up, an AC voltage pulse is generated. These pulses provide an outpu
frequency that is proportional to volumetric ow.
Accurate (±1% of reading) andreliable (repeatability ±0.25%) ow
measurement solution
GT Series Gas Turbine
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 5/8k i m r a y . c o m
Materials of Construction:
Body; 316 L Stainless Steel
Flanges; 316 Stainless Steel
Rotor; 431 Stainless Steel
Rotor Shaft; Tungsten Carbide
Flow Linearity: ±1% of reading
Repeatability: ± 0.25%Frequency Output: 100 to 1,100 Hz
Voltage Output: Approximately 100mV @ 100 Hz
to 1.5 V (RMS) @ 1,000 Hz
Pressure Rating: 5,000 psi (maximum)
Pressure Drop: 0.5 psi at 100% of ow range
Turbine Temperature: -20 °F to +300 °F
(-29 °C to 149 °C)
Extended Temperature: -200 °F to +450 °F
(-130 °C to 218 °C)
Specifcations
FIt is recommended that at least one spare Internal Parts Kit be kep
for each size and ow range of gas meter. This will provide a calibrated
replacement should a problem develop with the meter in service. Thi
avoids costly delays associated with even a short down time. The
internal parts kits include a calibrated gas cartridge and a new spira
lock ring.
Repair Kits
Part Number Description
KSB253-2HK-150 Hardware Kit 2” 150#
KSB253-2HK-300 Hardware Kit 2” 300#
KSB253-2HK-600 Hardware Kit 2” 600#
KSB253-2HK-900 Hardware Kit 2” 900#
KSB253-2HK-1500 Hardware Ki t 2” 1500#
Wafer Style Meters
Part Number Meter
Size
End
ConnectionEnd to End
Flow
ACFM
Ranges
ACFH
Nom. K-Factor
P/ACF
GT Repair Kit
Part Number
KSIGT9/2000L 2” Wafer 2” 1.75” 3 .0-30 175-1750 2,100 KSIP539309
KSIGT9/2000M 2” Wafer 2” 1.75” 4 .5-45 275-2750 1,300 KSIP535329
KSIGT9/2000H 2” Wafer 2” 1.75” 8.5-85 500-5000 720 KSIP539310
KSIGT9/2000XH 2” Wafer 2” 1.75” 20-200 1200-12000 300 KSIP539311
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 6/8
Introduction
Operating Principle
Model B2800 Advanced Flow Monitor
The B2800 is an advanced microprocessor-based ow monitor that
is also low cost and simple to operate. When ordered with a Kimray
turbine meter, the B2800 is congured at the factory for units of rate
and total. Or, the unit may be easily programmed in the eld. The
monitor has a large two-line display and is available in power and
mounting options to suit almost any application.
The B2800 advanced ow monitor accepts a low-level frequency input
such as the input from a Kimray turbine meter, to calculate ow rate
and total. These calculations are then displayed in user selected units
of measurement. All B2800 advanced ow monitors can be easily
recongured in the eld. The B2800 is available in a battery-powered o
loop-powered version. The battery version utilizes one “D” size, 1.5 vol
alkaline battery that provides up to 3-1/2 years of service.
The loop-powered B2800 offers a 2-wire 4-20 mA output for electronic
integration. The meter mount, remote, swivel and hand-held monitors
are equipped with a large 8 digit by 3/4” numerical LCD making
extended range viewing practical. The second 8 character by 3/8
alphanumeric display provides for selectable units viewing in run mode
and prompts variables in programming mode. Additionally, the user can
choose between displaying rate, total or alternating between both rate
and total.
Note: Only the “Advanced Flow Monitor” will work with gas meters.
User friendly front panelprogamming
Meter, Remote, Panel andSwivel mount versions
available
Explosion-Proof and Hand-Held models available
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 7/8
LCD Display: Rate & total, xed or toggle modes of operation 8 digit, 0.7 inches (18 mm)
numeric (top line) 8 character, 0.35 inches
(9 mm) alphanumeric (bottom line);
resettable
Power:
Battery
Loop-Powered
1 “D” size 1.5 VDC alkaline battery
included Less than 1 milliwatt (~3.5 years
on 1 “D” battery)
4-20 mA, two-wire current loop 25 mA
maximum consumption
Units of Measure:
(Total)
(Advanced Version - user selectable)
Cubic Meters, Cubic Ft,
MCF, MMCF
Certifcations:
CSA Intrinsically Safe: Class I, Division 1, Groups C & D
Class II, Division 1, Groups E, F & G
CE: IEC 61326-1
CSA: (Panel Mount Only) Ordinary Area
CSA Hazardous Locations:
(Explosion-Proof Model Only)
Class I, Division 1, Groups B, C & D
(Explosion-Proof Model Only) Class II,
Groups E, F & G
Class III, Type 4, T6 @ 70 C
Specifcations
k i m r a y . c o m
Part Number Units Mounting Style
Model B2800 Flow Monitor, Advanced - Battery Powered
KSB28ABP-CS Panel Mount
KSB28ABS-CS Customer Swivel Mount
KSB28ABX-CS Selectable Explosion-proof
KSB28ABM-CS Meter Mount
Model B2800 Flow Monitor, Advanced - Loop Powered
KSB28ALM-CS Customer Meter Mount
KSB28ALR-CS Selectable Remote Mount
KSB28ALX-CS Explosion-proof
7/29/2019 Gas Flow Meter Product Guide
http://slidepdf.com/reader/full/gas-flow-meter-product-guide 8/8
SSGM-001 - Gas Meter Product Guide
k i m r a y c o m
Part Number Description
KSB220-218 Cable Assy 10’ 2 pin w/hub protector
KSB220-218-30 Cable Assy 30’ 2 pin w/hub protector
KSB220-218-50 Cable Assy 50’ 2 pin w/hub protector
KSB220-220 Cable Assy 10’ w/90 conn
KSB220-221 Cable Assy 10’ w/straight conn
KSB220-221-15 Cable Assy 15’ w/straight conn
KSB220-221-25 Cable Assy 25’ w/straight conn
KSB220-221-50 Cable Assy 50’ w/straight conn
KSB220-221-75 Cable Assy 75’ w/straight conn
KSB222-126 Conn Assy; 2 pin Amphenol, str
KSI64920774 Low Drag Magnetic Pick-up
Parts and Accessories
Part Number Description
KSB280601 Alkaline Battery D Model 2800
KSB280-612 2800 Lid w/Gasket
KSB280-676 Mounting Bracket Kit 2” Pipe
KSB222-121 Cable Assy 12” Pigtail for 2800
KSB260630 Desiccant Bag
KSB280641 2800 Key Pad (Kimray)
B2800 Replacement Parts
Flow Meter Accessories