giv mc 320004

7/29/2019 Giv Mc 320004

1/6

Prod. No: Reg. No: Aircraft Hours Aircraft Landings Date: MM/DD/YY

320004 Main Landing Gear and Systems (Left) - Lubrication ISS/REV: 07/31/11

MM REF: 32-10-00

COMP CHG

OPS CHK OK AS ISSERV / ADJ

REQUIRED

S V W

TECH INSP M/HRS

C/W SOURCE:

SIGNATURE: CERTIFICATE NUMBER:

Prod. No: Reg. No: Aircraft Hours Aircraft Landings Date: MM/DD/YY

320005 Main Landing Gear and Systems (Right) - Lubrication ISS/REV: 07/31/11

MM REF: 32-10-00

COMP CHG

OPS CHK

OK AS ISSERV / ADJ

REQUIRED

S V W

TECH INSP M/HRS

C/W SOURCE:

SIGNATURE: CERTIFICATE NUMBER:

ISSUED/REVISED: 07/31/11

AREA320004 Main Landing Gear and Systems (Left) - Lubrication320005 Main Landing Gear and Systems (Right) - Lubrication

A. Preparation

SPECIAL TOOLS AND TEST EQUIPMENT

Grease gun ....................................................................................... GSE1200474 or equivalentGrease gun adapter ......................................................................... GSE1200267 or equivalentOil can ............................................................................................................................ Standard

CONSUMABLES

Corrosion inhibiting compound ........................................................................................ Type VIIGrease ................................................................................................................. MIL-PRF-23827

Hydraulic fluid ........................................................ MIL-H-5606, MIL-H-83282B or MIL-H-87257Lubricant (LPS-2) ................................................................................... MIL-PRF-81309 Type IIIOil, General Purpose ............................................................................................. MIL-PRF-7870

NOTE: See Hydraulic Servicing, 12-01-05, System Description.

(1) References Hydraulic Servicing, 12-01-05, System Description Prevention of Corrosion, 51-01-00, Servicing

(2) Aircraft Preparation

(a) Prepare aircraft for safe ground maintenance.

GIV COMPUTERIZED MAINTENANCE PROGRAM320004Page 1 of 6

MSG-3

MSG3

Title Page Prev Page Next Page Index

7/29/2019 Giv Mc 320004

2/6

ISSUED/REVISED: 07/31/11(CONTINUED) AREA

320004 Main Landing Gear and Systems (Left) - Lubrication320005 Main Landing Gear and Systems (Right) - Lubrication

WARNING: FAILURE TO INSTALL ALL LANDING GEAR AND LANDING GEARDOOR SAFETY DEVICES BEFORE WORKING IN ANY WHEEL

WELL MAY RESULT IN SERIOUS INJURY OR DEATH.

FAILURE TO DISSIPATE HYDRAULIC PRESSURE BEFOREINSTALLING OR REMOVING ALL LANDING GEAR AND LANDINGGEAR DOOR SAFETY DEVICES SHALL CAUSE DAMAGE TO

AIRCRAFT OR MAY RESULT IN SERIOUS INJURY OR DEATH.

FAILURE TO ENSURE ALL PERSONNEL AND EQUIPMENT ARECLEAR OF FLIGHT CONTROL SURFACES BEFORE OPERATINGFLIGHT CONTROLS MAY RESULT IN SERIOUS INJURY OR DEATH.

(b) Dissipate hydraulic system pressure by cycling flight controls and / or operating brake

pedals several times.

(c) Install all landing gear and landing gear door safety devices.

B. Procedure

WARNING: MANY OF THE MATERIALS SPECIFIED HAVE SIGNIFICANT OCCUPATIONALSAFETY, HEALTH OR ENVIRONMENTAL REQUIREMENTS RELATED TO

THEIR USE. MATERIAL SAFETY DATA SHEETS SHALL BE CONSULTED FORALL MATERIALS TO DETERMINE THE MANUFACTURERSRECOMMENDATIONS CONCERNING OCCUPATIONAL EXPOSUREPRECAUTIONS. IT IS THE SOLE RESPONSIBILITY OF THE USER TO

ENSURE PROTECTION FROM INJURY OR EXPOSURE, SAFE APPLICATIONOF MATERIALS AND COMPLIANCE WITH ANY FEDERAL, STATE OR LOCAL

REGULATIONS REGARDING THE USE OF ANY OF THE MATERIALSSPECIFIED.

(1) Lubricate left and right main landing gear at lubrication points listed below. See Figure 1,Figure 2 and Figure 3.

(a) Door hinges.

(b) Door linkage.

(c) Spray main landing gear manual door control valve arm shaft with corrosion inhibitingcompound.

NOTE: See Prevention of Corrosion, 51-01-00, Servicing for corrosion inhibitingcompounds and application methods / precautions.

(d) Uplock mechanism and uplock shaft trunnions.

(e) Main landing gear strut assembly and strut trunnion.

(f) Side brace actuator.

(g) Door actuator.

(h) Uplock actuator.

(i) Sequencing Linkage.


MSG-3

MSG-3


7/29/2019 Giv Mc 320004

3/6



NOTE: Excessive pressure applied to Zerk fittings on left and right main landinggear posts may inadvertently dislodge fittings.

C. Follow On

(1) Inspect for presence of foreign objects.

(2) Record all maintenance actions in accordance with current governing authority.


MSG-3

MSG3


7/29/2019 Giv Mc 320004

4/6



BASE SPECIFICATION TYPE LUBRICATIONIDENTIFICATION

LETTER

MIL - H - 5606

GREASE LOW / HIGH TEMPERATURE

FLUID, HYDRAULIC

FLUID, HYDRAULIC MINERAL BASE

OIL, GENERAL PURPOSE, LOW TEMPERATURE

GIA

HO

OHA

OGP

TABLE OF LUBRICANTS

HO

GIA

GIA

GIA

GIA

GIA

GIA

OHA

GIA

OGP

HO

NOTE :

DETAIL A

GIA GIA

SEE DETAIL A

GIA

GIA

1

1

GIA

GIA

4 PLACES

GIA

2 PLACESGIA

2 PLACES

GIA

2 PLACES

SEE MAINT. MAN.CHAPTER 12

NOTE: S = HIGH PRESSUREGREASE FITTING

MIL - PRF - 23827

AIRCRAFT 1000 - 1213 HAVING ASC 307AND AIRCRAFT 1214 AND SUBSEQUENT

03947C04

MIL - PRF - 7870

Main Landing Gear - Lubrication

Figure 1


MSG-3

MSG-3


7/29/2019 Giv Mc 320004

5/6



Main Landing Gear Sequencing Linkage Support Lubrication Points

Figure 2


MSG-3

MSG3


7/29/2019 Giv Mc 320004

6/6



Main Landing Gear Uplock Lubrication Points

Figure 3


MSG-3

MSG-3


giv mc 320004

Documents