handrail assembly and steel stairs. handrail terminology u guardrail –top most rail on balcony...
TRANSCRIPT
Handrail Assembly and Steel Stairs
Handrail Terminology
Guardrail– top most rail on balcony
– higher than handrail Vertical Rail
– members between balusters
– ensure safety Handrail
– member that parallels angle of stairs
– ensure safety Horizontal Rail
– lower rail parallel to handrail
– ensure safety Baluster
– member that holds up handrail and vertical & horizontal railing
Handrail Terminology
Newel (newel post)– Large terminating
post at the bottom or top of stairs or landing
Half newel is next to the wall on the right
Handrail Terminology
Gooseneck– transition from handrail to guardrail due to
height difference
Handrails
Definition: a member that parallels the angle of the stairs allowing a person to grasp by hand to aid using the stairs
Serves 2 purposes– aid in ascending/descending stair– safety
Height restriction set by code– usually 34 - 38” (measured from edge of nosing)
Guardrail
Located at balconies, lookouts, and decks Any platform more than 30” above grade Top most rail of balcony railing Provides safety Height restrictions set by code
– Not less than 42”(measured from floor )
Guardrail Forces
Horizontal thrust normally 20 lbs/linear foot @ top of guardrail:– baluster 5 feet apart
– 5 (x) 20 = 100 lbs Baluster attachment @ floor:
– 100 lbs (x) 3’ height = 300 lbs Holding power of bolts - quantity
and size determined by architect/engineer
Vertical Rail
Spacing restricted set by code– present code 4” maximum gap between vertical
member, (9” in book is old code)– applies to all open railings if stairs are 30” or
more off floor
Steel Stairs
Steel Stair Details
Reasons for steel stairs– building code requirements for specific buildings
» commercial buildings (occupancy count considered)» exterior design of steel weather better than wood» fire protection
– structural strength and stability– aesthetics and design compatibility
» steel gives more flexibility in design» design rules are same as for other stair designs
Materials in Steel Stairs
Steel stringers Handrails Treads Metal clips and attachment Welding plates
Steel Stringers
Usually selected from steel channels– old callout 10[ 15.3 or 10C15.3– new callout C10 x 15.3
New callout explanation– 10 = nominal height of channel– C = type of steel section, in this case
an American Standard channel– 15.3 = weight per foot of steel section 10”
Steel Stringer Designs
A. Compound cut (two cuts) & plates welded to enclose channel
B. Completed design of A C. Single cut of channel D. Another channel cut as leg of
stringer E. & F. Completed design of leg
& stringer welded together
Example of Steel Channels Stringerswith Pre-fabricated Stair Units
Steel Handrail, Guardrails, & Treads A thru
D--Handrail/guardrails designs
E & F--Baluster attachment designs
G & H--Tread designs
Treads Materials and Construction Methods
Pre-cast/reinforced concrete
Reinforced concrete/metal pan
Treads Materials and Construction Methods
Concrete poured in place
Steel
Section of a Concrete “U” Shape Stairs
Metal Clips/Brackets
Metal angles– steel angles welded to
inter side of stringer
Metal brackets– triangle or other
shapes welded to top of stringer
Metal angle
Metal bracket
Metal Tread Bracket
Metal bracket welded to stringer to accommodate treads
Welding Plates Used to enclose end of stringer
(channel)– aesthetic– attachment of stringer to structure
Embedded in underneath side of pre-cast treads– purpose of attaching tread to
structure by welding
Welding plates
Handrail Assembly Details
Elevation/Section to include– material/size
» handrail
» vertical rails
» bottom rails
– height of handrail– spacing of vertical rails– detail callouts
Drawing Example Section/ Elevation @ 1” =1’-0”
Section/Elevation view of stairs
Changes:– Reverse direction
of section 7-7– vertical rails
@4”OC
more
Drawing ExampleHandrail Assembly Detail @ 6” =1’-0”
Section of wood handrail– callout of catalog to match cross-section or
sufficient dimensions to mill– connection method as shown– profile wood handrail
more
Drawing Example
Baluster Detail Section 6” =1’-0” Baluster
– weld symbol should be weld all around
– size of screws: 2-1/4” X 1 1/2” flathead screw
– locate center of screws 5/16” from edge,