honeywell connected plant video assist · capture, publish, and share videos which is compatible to...

HONEYWELL CONNECTED PLANT – VIDEO ASSIST

R110.1

___________________________________

Software Change Notice

___________________________________

VADOC-X563-en-1101B

August 2019

VADOC-X563-en-1101B 2

DISCLAIMER

This document contains Honeywell proprietary information. Information contained herein

is to be used solely for the purpose submitted, and no part of this document or its contents

shall be reproduced, published, or disclosed to a third party without the express

permission of Honeywell International Sàrl.

While this information is presented in good faith and believed to be accurate, Honeywell

disclaims the implied warranties of merchantability and fitness for a purpose and makes

no express warranties except as may be stated in its written agreement with and for its

customer.

In no event is Honeywell liable to anyone for any direct, special, or consequential damages.

The information and specifications in this document are subject to change without notice.

Copyright 2019- Honeywell International Sàrl

ABOUT THIS DOCUMENT


Table of contents 1 ABOUT THIS DOCUMENT .............................................................................................................................. 4

1.1 Revision history ....................................................................................................................................................... 4

1.2 Introduction ............................................................................................................................................................... 4

2 NEW FEATURES............................................................................................................................................... 5

2.1 New Features in R110.1 ...................................................................................................................................... 5

2.2 Key Features in R100.1 ........................................................................................................................................ 6

3 UPGRADING TO VIDEO ASSIST APPLICATION R110.1 ..................................................................... 7

3.1 Updating to latest version: ................................................................................................................................. 7

4 KNOWN ISSUES ............................................................................................................................................... 8

4.1 Known Issues in R110.1 ...................................................................................................................................... 8

4.2 Known Issues in R100.1 ................................................................................................................................... 11

5 OPEN SOURCE SOFTWARE INCLUDED ................................................................................................ 15

6 NOTICES.......................................................................................................................................................... 17

ABOUT THIS DOCUMENT


1 About this document

This Software Change Notice contains important information that must be read prior to

installing and working with Honeywell Connected Plant Video Assist. It also contains

known issues, documentation updates, and additional information.

1.1 Revision history

Version Release Date Description

A R100.1 December 2018 The initial release of the document.

B R110.1 August 2019 New features and enhancements in R110.1. List

of unknown issues and corresponding

workarounds.

1.2 Introduction Honeywell Connected Plant – Video Assist is an easy-to-use android application to

capture, publish, and share videos which is compatible to view in the Intelligent Wearables

device. Video Assist is your Augmented Reality- visual media environment for industrial or

plant specific videos.

Video Assist is a procedure creation and video tutorial solution enabling on-demand

access to customer-site-specific training procedures on and off the field. The procedures

are created by plant experts /seniors. It ensures quick and accurate issue resolution at

plant and saves travel cost and time. The video library acts as a visual aid on how to

perform any complex procedure in the plant without having to memorize the whole

procedure.

NEW FEATURES


2 New Features

Honeywell Connected Plant – Video Assist offers the following features across the

releases.

2.1 New Features in R110.1 Following are features available in Video Assist R110.1:

Easier Password Management - Video Assist portal is integrated with Microsoft

Login function for user to personalize the system assigned password. Enhanced

create procedure process – Simplified process to capture procedure, eliminating

the need to dictate title for each step. Easy to edit all the procedure properties via

portal. For more information about enhancement in Intelligent Wearable camera

functions, see My Camera Features.

Instant Step Video Edit - Provision to Preview each step video instantly after

capturing the step. Based on the preview, you can decide to either save or discard

the step in the procedure.

Procedure Draft Management – Two new variations of drafts: Online Drafts and

Local Drafts are introduced in the Video Assist applications to store procedures at

various stages. You can opt to save draft at the end of capturing all the steps. Save

draft procedures will be listed under Local Drafts that are accessible only via

application. You can opt to upload the procedure at the end of capturing. Uploaded

procedure will be listed under Online Drafts that are accessible via both application

and portal.

Noise Reduction – Enables you to reduce the constant background noise such as

humming or hissing.

Voice Over – Enables you to override recorded audio with new audio track.

Select Video Speed – Enables you to play step video in different speed.

New Publish Mechanism – Publish provides you the flexibility to edit both saved

and uploaded procedures before making it visible for other users.

Edit Published Procedure and Steps – Provision to move the published procedure

to draft and edit in case the procedure needs further modification.

Text Based Search - Basic text based search that enables you to search for a

procedure both Online procedures and Offline (downloaded) procedures.

New Android Version Support - Video Assist application is compatible and

qualified to use with latest Intelligent Wearable Release 10 with Android 8.

Performance Enhancement - Step video upload speed is improved to 20-30

seconds for a one (1) minutes video.

NEW FEATURES


2.2 Key Features in R100.1 Following are features available in Video Assist R100.1:

Create procedures – A procedure is a playlist that contains either single or multiple

steps arranged in specific order to aid performing a task. Capture individual steps

to create logical flow for the task.

Add multiple steps to the procedure – You can add multiple steps to a single

procedure.

Upload the new procedure – Newly created procedure must be uploaded for other

users to view or download.

Edit procedure properties – Edit the properties of specific procedure such as title,

description, and key words.

Delete procedures – Delete an uploaded procedure.

Stream the procedure online – View the procedure directly from the cloud while

connected to internet (online) via streaming.

Download and view the procedure offline – Specific procedure must be

downloaded to the Intelligent Wearable when online to view when disconnected

from internet (offline).

UPGRADING TO VIDEO ASSIST APPLICATION R110.1


3 Upgrading to Video Assist Application R110.1

You will receive a notification whenever a new version of Video Assist application is

available for download on the Intelligent Wearable. If you have set to automatically update

application when latest version is available, then application is updated without any

intervention.

Remember in this case you may lose the procedures saved as drafts.

If you have disabled automatic app update, then prior to update you must upload all the

procedures that are saved as drafts.

3.1 Updating to latest version: 1. You will receive a notification informing the availability of latest version of Video

Assist.

2. Upload all the procedures that are saved as drafts.

3. You can opt to update immediately on receiving the notification. Say OK.

4. You can opt to update later in time. Say Remind Me Later.

KNOWN ISSUES


4 Known Issues

4.1 Known Issues in R110.1

Issue No. Issue - Description/Recovery/Workaround

1. RREALWEAR-960 Error: Add Title dialog box and commands (Enter Text, Save and Upload,

or Close) in the dialog are not responsive and the application shows

numbered bubbles for the behind screen.

Description: Using Intelligent Wearable with Android 8.1 Operating

System, you have captured a step video for a procedure and opted to

upload. The Add Title dialog box and the commands are non-responsive

in following two scenarios:

1. When you close the keyboard after entering the title manually or

accidentally.

2. In few devices, virtual keyboard is hidden by default.

Workaround: When the focus in not on Enter Text pop-up, say Show

Notification and Hide Notification. Then utter any of the commands

Enter Text, Save and Upload, or Close; you will be able to perform the

actions.

2. RREALWEAR-829 Error: On the portal thumbnail is missing for procedure that contains

step with encoding error.

Description: If steps are in fix state for a procedure due to encoding

error, then the thumbnail is not displayed for the specific procedure.

Workaround: None.

3. RREALWEAR-803 Error: No command option to close the sub-menu of Show Drafts.

Workaround: None.

https://acsjira.honeywell.com/browse/RREALWEAR-960



KNOWN ISSUES



4. RREALWEAR-802 5.

Error: On the Homepage when Show Drafts command is active, then no

other commands are responsive.

Workaround: None.

6. RREALWEAR-790 Error: Step titles modified on the portal are not visible when Online Draft

procedures are edited using the application.

Workaround: None.

7. RREALWEAR-763 Error: A blank procedure is created even when Save Draft or Upload is

selected.

Description: While creating a new procedure if you use Homepage

command either before or after saving the captured step, then a blank

procedure is listed in the Local Drafts.

Workaround: None.

8. RREALWEAR-800 Error: On migration, no serial number is assigned for the step title, Edit

Video, Discard.

Description: Migrating from R100.1 to R110.1 – procedures that were

created using R100.1 and saved as draft. On migration, no serial number

is assigned for the step title, Edit Video, Discard.

Workaround: Upload the draft version of procedures before migrating to

R110.1.

9. RREALWEAR-738 Error: Noise cancellation cannot be performed for a step video length

greater than four (4) minutes.

Workaround: Opt to perform noise cancellation on videos of shorter

duration.






KNOWN ISSUES



10. RREALWEAR-759 Error: No Storage message appears while capturing the step even when

sufficient space is available.

Description: After capturing each step video, a message stating No

Storage Left appears even though sufficient space is available.

Workaround: None.

11. RREALWEAR-736 Error: Procedure owner information is not updated if the published

procedure is edited and published.

Description:

Scenario 1: Field Expert 1 creates and publishes a procedure. Field

Expert 2 moves the published procedure to draft and edits the

procedure before republishing.

Scenario 2: Administrator 1 moves published procedure to drafts that

was previously published by Administrator 2 or Field Expert 1.

In both scenarios, other users edit the procedure before republishing the

procedure. However, procedure owner is not updated to Field Expert 2 or

Administrator 1.

Workaround: None.

12. RREALWEAR-740 Error: No option to search procedures in draft stage either in Video

Assist portal or application.

Workaround: None.




KNOWN ISSUES


4.2 Known Issues in R100.1 This section provides list of known issues applicable for lessons.


13. RREALWEAR-236 Error: Replay option in Manual mode plays next step instead of same

step.

Description: On choosing to play the procedure in Manual mode and

end of specific step replay does not repeat the step instead skips to

play the next step in the procedure.

Workaround: None.

14. RREALWEAR-333 Description: User is not auto-logged out after long idle hour from the

Video Assist portal.

Workaround: Manually log out.

RREALWEAR-335 Error: Title for the currently playing step is not displayed in the full-

screen mode.

Workaround: None.

RREALWEAR-336 Error: Invalid media file error message when invalid media file is

uploaded in the Video Assist portal.

Description: In case invalid media file with extension of MP4 format,

the file is not uploaded but no failure message is displayed.

Workaround: None.

15. RREALWEAR-351 Error: No failure message when admin user attempts to delete self.

Description: When Admin user attempts to delete self, no error or

failure message is displayed. Admin has no privilege to delete self,

however admin can delete other users.

Workaround: None.

16. RREALWEAR-355 Error: Search result page does contain Show Menu or Homepage

option for alternate navigation.

Workaround: None.

17. RREALWEAR-369 Error: Option selected for quality of the video does not match when

streaming the video.

Workaround: None.

18. RREALWEAR-398 Error: Scroll bar is not enabled when the number of video exceeds the

display area.

Workaround: None.









KNOWN ISSUES



19. RREALWEAR-287 Description: Video Assist application in the Intelligent Wearables does

not indicate if the device is online or offline on the Homepage.

Workaround: Show Menu voice command displays a different menu

option when the device is connected to internet versus when

disconnected.

Offline Menu options:

Online Menu options:

20. RREALWEAR-382 Error: No warning or failure message to indicate network disconnection

while search is in progress.

Workaround: None.



KNOWN ISSUES



21. RREALWEAR-350 Error: Change password is not available.

Workaround: You can change password as follows:

1. Launch https://login.microsoftonline.com site.

2. Under Apps, select Outlook option.

3. Login using your Video Assist credentials.

4. Click your detail displayed on top-right corner of the window and

select My account.

5. From the left pane, select Security & privacy.

6. Update your password by entering and confirming the new password.

7. Remember to login with new password in both the Video Assist portal

and the application on the device.

22. RREALWEAR-402 Error: Whenever there is breakage in internet connection and on

reconnecting to internet, there is lag in updating status for the

following scenarios:

Show Menu still display Offline options or displays Online menu

options partially.

Homepage displays the steps as draft whereas the procedure is

successfully uploaded to cloud.

Workaround: None.

23. RREALWEAR-403 Error: No pagination on Search result.

Workaround: None.


https://login.microsoftonline.com/



KNOWN ISSUES



24. RREALWEAR-414 Error: Video recorder timer skips count every 9th second.

Workaround: None.


OPEN SOURCE SOFTWARE INCLUDED


5 Open Source Software Included

Video Assist uses the following open source software.

MIT License

Video Assist uses the following components:

Angular Animation 6.0.0

Bootbox.js 4.4.1

Bootstrap 3.3.7

filesaver.js 1.3.4

jquery - jquery/jquery 3.3.1

jsPDF 1.2.60

Angular/common 6.0.0

Angular/compiler 6.0.0

Angular/core 6.0.0

Angular/forms 6.0.0

Angular/http 6.0.0

Angular/platform-browser 6.0.0

Angular/platform-browser-dynamic 6.0.0

Angular/router 6.0.0

ng-bootstrap/ng-bootstrap 2.0.0

ngx-translate/core 10.0.1

ngx-translate/http-loader 3.0.1

Angular-progress-http 1.0.0

rxjs 6.1.0

rxjs-compat 6.2.1

vivus 0.4.3

Yarn 1.6.0

zone.js 0.8.26

core-js 2.5.5

OPEN SOURCE SOFTWARE INCLUDED


ng2-file-upload 1.3.0

ngx-bootstrap 3.0.1

Stream 0.0.2

ngx-carousel 1.3.5

adal-angular4 4.0.11

videogular2 6.2.2

videojs-hlsjs 1.4.8

dashjs 2.6.8

Hammerjs 2.0.8

hls.js 0.9.1

crypto-js 3.1.9-1

ng2-cookies 1.0.12

ng2-dragula 2.1.1

Recordrtc 5.5.2

NOTICES


6 Notices

Trademarks

Experion®, PlantScape®, SafeBrowse®, TotalPlant®, and TDC 3000® are registered

trademarks of Honeywell International, Sàrl.

OneWireless™ is a trademark of Honeywell International, Sàrl.

Other trademarks

Microsoft and SQL Server are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

Trademarks that appear in this document are used only to the benefit of the trademark

owner, with no intention of trademark infringement.

Third-party licenses

This product may contain or be derived from materials, including software, of third parties.

The third party materials may be subject to licenses, notices, restrictions and obligations

imposed by the licensor.

The licenses, notices, restrictions and obligations, if any, may be found in the materials

accompanying the product, in the documents or files accompanying such third party

materials, in a file named third_party_ licenses on the media containing the product, or at

http://www.honeywell.com/ps/thirdpartylicenses.

Documentation feedback

You can find the most up-to-date documents on the Honeywell Process Solutions support

website at:

http://www.honeywellprocess.com/support

If you have comments about Honeywell Process Solutions documentation, send your

feedback to:

[email protected]

Use this e-mail address to provide feedback, or to report errors and omissions in the

documentation. For immediate help with a technical problem, contact your local

Honeywell Process Solutions Customer Contact Center (CCC) or Honeywell Technical

Assistance Center (TAC).

How to report a security vulnerability

For the purpose of submission, a security vulnerability is defined as a software defect or

weakness that can be exploited to reduce the operational or security capabilities of the

software.

http://www.honeywell.com/ps/thirdpartylicenses

http://www.honeywellprocess.com/support

mailto:[email protected]

NOTICES


Honeywell investigates all reports of security vulnerabilities affecting Honeywell products

and services.

To report a potential security vulnerability against any Honeywell product, please follow the

instructions at:

https://honeywell.com/pages/vulnerabilityreporting.aspx

Submit the requested information to Honeywell using one of the following methods:

Send an e-mail to [email protected].

or

Contact your local Honeywell Process Solutions Customer Contact Center (CCC) or

Honeywell Technical Assistance Center (TAC) listed in the “Support” section of this

document.

Support

For support, contact your local Honeywell Process Solutions Customer Contact Center

(CCC). To find your local CCC visit the website, https://www.honeywellprocess.com/en-

US/contact-us/customer-support-contacts/Pages/default.aspx.

Training classes

Honeywell holds technical training classes that are taught by process control systems

experts. For more information about these classes, contact your Honeywell representative,

or see http://www.automationcollege.com.

https://honeywell.com/pages/vulnerabilityreporting.aspx

mailto:[email protected]

https://www.honeywellprocess.com/en-US/contact-us/customer-support-contacts/Pages/default.aspx

https://www.honeywellprocess.com/en-US/contact-us/customer-support-contacts/Pages/default.aspx

http://www.automationcollege.com/

honeywell connected plant video assist · capture, publish, and share videos which is compatible to...

Documents