ideal 4855 ideal 5255 - mybinding.com · - 3 - d keine bedienung durch kinder! gb children must not...

Triumph 5255 20.375" Electric Programmable

Paper Cutter

Instruction Manual

https://www.mybinding.com/

tel:1-800-944-4573

https://www.mybinding.com/triumph-5255-electric-programmable-paper-cutter.html

IDEAL 6655

IDEAL 4855 IDEAL 5255

GB Operating InstructionsGuillotines

MyBinding.com5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

http://www.mybinding.com



IDEAL 4855 • IDEAL 5255 • IDEAL 6655

- 2-

D Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitungund beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeitverfügbar sein.

GB Please read these operating instructions before putting the machine into operationand observe the safety precautions. The operating instructions must always beavailable.

F Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine,et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisationet les consignes de sécurité doivent toujours être disponibles. Les instructionsd'utilisation et les consi.

NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzinggoed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing ende veiligheids-voorschriften moeten altijd binnen handbereik zijn.

I Per favore legga questo manuale di istruzione prima di mettere in funzione ildistruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devonoessere sempre disponibili.

E Le recomendamos lea las instrucciones antes de poner en funcionamiento estamáquina y cumpla las normas de seguridad. Las instrucciones de servicio yseguridad deben estar siempre disponibles.

S Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga medsäkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig.

FIN Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen !Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla.

N Lees gjennom denne bruksannvisningen før De tar i bruk maskinenVær oppmerksom på sikkerhetsforskriftene. Opperatørmanualenmå alltid være tilgjengelig.

PL Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia istosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą byćzawsze dostępne.

RUS Ïîæàëóéñòà, ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ïåðåä óñòàíîâêîéàïïàðàòà, ñîáëþäàéòå òåõíèêó áåçîïàñíîñòè. Èíñòðóêöèÿ ïîýêñïëóàòàöèè äîëæíà íàõîäèòüñÿ â äîñòóïíîì äëÿ ïîëüçîâàòåëÿ ìåñòå.

H A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsabe a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie.

TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekildeokuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarýher zaman kullanýma hazýr olmalýdýr.

DK Før installation af maskinen bedes De venligst læse brugervejledningenog være opmærksom på sikkerhedsanvisningerne. Brugervejledningenskal altid være tilgængelig.

CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostníupozornění. Návod k obsluze musí být vždy dostupný.

P Por favor leiam o manual de instruções antes de colocar a máquina em operaçãoe vejam as precauções de segurança. As instruções de operação deverão estarsempre disponíveis.

GR ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ.ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ.

SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorilapreden zaženete naparavo. Navodila naj bodo vedno pri roki.

SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja doprevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu nadostupnom mieste.

EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgigeohutusnõudeid. Kasutusjuhend peab alati käepärast olema.

CHI

UAE

• Safety precautions •

- 3 -

D Keine Bedienung durch Kinder!GB Children must not operate the machine!F Pas d‘utilisation par un enfant!

NL Geen bediening door kinderen!I Non lasciare utilizzare il tagliacarte a bambini!E No dejar que la utilicen los niños!S Installera maskinen utom räckhåll för barn!

FIN Asentakaa laite lasten ulottumattomiin !N Installer maskinen utenfor rekkevidde for barn!PL Dzieciom nie wolno obsługiwać urządzenia !

RUS Íå äîïóñêàéòå äåòåé ê ïîëüçîâàíèþ àïïàðàòîì!H Gyerekek a gépet nem kezelhetik

TR Makinayý Çocuklar Kullanmamalýdýr.DK Må kun betjenes af voksneCZ Stroj nesmí být obsluhován dětmi!P As crianças não devem trabalhar com a máquina!

GR ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ.SLO Otroci ne smejo uporabljati napraveSK So strojom nesmú pracovat deti!EST Lapsed ei tohi masinat kasutada!CHIUAE

D Nicht unter das Messer fassen!GB Do not reach beneath the blade!F Ne pas passer les mains sous la lame!

NL Niet met de handen onder het mes komen!I Non toccare la lama nella parte inferiore!E ¡No tocar debajo de la cuchilla!S Sträck inte in handen under kniven!

FIN Älä laita kättäsi terän alle !N Plasser aldri hender ol. under kniven !PL Nie wkładać rąk pod noże!

RUS Èçáåãàéòå ïîïàäàíèÿ ðóê ïîä ëåçâèå!H Ne nyúljon a kés alá!

TR Elinizi býçaðýn altýna sokmayýnýz!DK Stik ikke hænderne ind under knivbladet!CZ Nesahejte pod ostří nože!P Não tocar na parte inferior da faca!

GR ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ!SLO Ne segajte z roko pod rezilo!SK Nevkladajte ruky pod nôž!EST Ärge pange kätt tera alla!CHIUAE


- 4 -


D Messer nie lose liegen lassen!Messer nur mit Messerwechselvorrichtung oder imMessertransportkasten befördern!(siehe Seite 29 und 31).

Warnung! Verletzungsgefahr!GB Never leave the blade unattended!

Do not extract or transport the blade without protection!(See page 29 and 31).

Danger! Risk of injury!F Ne jamais laisser la lame sans protections !

Elle ne doit être démontée qu’à l’ aide du dispositif dechangement de lame (cf. page 29 et 31), ou transportée dansson étui en bois !

Danger! Risques de coupures !NL Laat nooit de messen alleen achter.

Transporteer de messen niet zonder de houten bescherming(zie pagina 29 en 31).

Waarschuwing! Opgelet voor ongevallen!I Non lasciare mai la lama incustodita. Non rimuovere o

trasportare la lama senza protezione. (Vedi pagina 29 e 31). Attenzione! Rischio di infortunio!

E ¡No quitar la cuchilla sin prestar atención. No desmontar notransportar la cuchilla sin protección! (vérase pág. 29 y 31)

¡Advertencia! ¡Peligro de hacerse daño!S Lämna aldrig maskinen obemannad. Ta inte ur eller

transportera kniven utan skydd. (se sid 29 och 31). Skaderisk!

FIN Käsittele terää aina varoen. Älä siirrä tai kuljetaterää ilman suojaa ! (katso sivu 29 ja 31

Loukkaantumisen vaara !N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller

transporter den uten beskyttelse (Se side 29 og 31) FARE ! Muligheter for skade !

PL Nigdy nie pozostawiać noży bez nadzoru.Nie wyciągać lub transportować noży bez osłon!(zobacz strona 29 i 31).

Ryzyko skaleczenia sie!RUS Íå îñòàâëÿéòå îòêðûòîå ëåçâèå áåç ïðèñìîòðà! Íå

ïûòàéòåñü èçâëå÷ü èëè òðàíñïîðòèðîâàòü ëåçâèå áåçñïåöèàëüíûõ ìåð ïðåäîñòîðîæíîñòè!(Ñì. ñòðàíèöû 29 è 31)

Ñîáëþäàéòå âûøå ïåðå÷èñëåííûå ïðàâèëàäëÿ èçáåæàíèÿ òðàâì!

H Soha ne hagyja a kést őrizetlenül!Ne vegye ki vagy ne szállítsa a kést védőtok nélkül!(Lásd 29. és 31. oldal)

Veszély! Sérülésveszély!TR Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz!

Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veyataþýmayýnýz! (Sayfa 29 ve 31’e bakýnýz)

Dikkat! Yaralanma riski!


- 5 -

DK Knivbladet må aldrig efterlades uden opsyn.Forsøg ikke at afmontere eller transportere knivbladet udenbeskyttelse! (Se side 29 og 31)

FARE! Risiko for legemlig beskadigelse.CZ Nikdy nenechávejte nůž bez krytu.

Nikdy nevyjímejte nebo neprepravujte nuz bez ochrannéhokrytu (viz. strany 29 a 31)

Nebezpecí! Riskujete zraneníP Deixar a faca sempre em local seguro!

Não retirar ou transportar a faca sem protecção!(Ver pág. 29 e 31)

Perigo! Risco de dano!GR ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ!

ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 29 & 31)

ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ !SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte

rezilo brez zaščite. ( glej stran 29 in 31). Pozor! Nevarnost poškodbe.

SK Nenechávajte nôž nechránený (nezabezpecený)!Nevyberajte alebo netransportujte nôž bez ochrany(vid s. 29 a 31)

! Riziko úrazu !EST Ärge jätke lõiketera kunagi järelevalveta!

Ärge pikendage ega teisaldage tera kaitseseadmeteta!(Vt lk 29 ja 31)

Oht! Vigastuste oht!CHI

UAE2931

3129




- 6 -


D Keine harten und splitternden Materialien schneiden!GB Do not cut hard materials or materials which may splinter!F La coupe de matériaux trop durs ou risquant des projections

est interdite !NL Snij geen harde materialen of materiaal dat kan splinteren!I Utilizzare il tagliacarte esclusivamente per il taglio di risme

di carta o materiali analoghi!E ¡No cortar materiales duros o materiales que puedan

astillarse!S Förstör inte hârt material eller material som kan splittras!

FIN Asentakaa laite lasten ulottumattomiin !N Ikke kutt hardt metall eller materiale som kan splintre !PL Nie ciąć twardych materiałów lub materiałów, które mogą

ulec odpryśnięciu!RUS Äàííûé ðåçàê íå ïðåäíàçíà÷åí äëÿ ðåçêè òâåðäûõ

ìàòåðèàëîâ èëè ìàòåðèàëîâ, êîòîðûå ìîãóòðàñùåïëÿòüñÿ!

H Ne vágjon kemény vagy olyan anyagot, amely repedhet!TR Sert veya parçalanabilecek malzemeleri kesmeyiniz!DK Der må ikke skæres i hårde materialer eller i materialer, der

kan splintre!CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré

úlomky!P Não cortar materiais duros ou materiais que possam lascar!

GR ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕÈÑÕÌÌÁÔÉÆÏÍÔÁÉ!

SLO Nikoli ne režite trdih materialov ali materialov, ki se lahkorazcepijo.

SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžuvystrelovat ostré úlomky.

EST Ärge lõigake kõvasid materjale ega materjale, mis võivadpilbasteks puruneda!

CHIUAE




- 7 -

The machine is designed for cutting stacks ofpaper to a specified size.This machine is constructed for "one-manoperation" only!

Warning! Clips or similar damage thecutting blade.

Disconnect from the mains before starting anyservice work or before removing the panels!

Replacement of blade and cutting stick maybe performed only when the main switch isswitched off!




- 8 -


AA

A

CC

A

B

All components which could endanger theoperator are covered by a guard!


Operating the machine without safety device isforbidden!(Front safety guard (A), rear screwed safetyguard (B) and panel (C).



- 9 -

A

A

CB


The dangerous cutting movement issafeguarded by a movable guard (A) and asafety two-handed control system! (B)

Before working with the machine and afterevery blade replacement the automatic cut-offfunction of safety guard (A),(correct if distancebetween cover and table is < 20 mm) mainswitch (B) and control panel (C) must bechecked.



- 10 -


230V / 10A min115V / 15A min

Connect the power cord to a single phasesocket.

Ensure free access to mains!


When not in use for a longer period switch off.(Main switch to "0").



- 11 -


Clamping BladeOK

OK

Danger!Blade must always be covered by thepressing bar.

Protect mains cable against heat, oil andsharp edges!



- 12 -


Remove the stand from the wooden pallet.

4 strong people are required to lift the machinefrom the pallet and place it on the stand.Secure with 4 screws (A). Put the shelf (B) onthe stand. (Parts and tools are in the tool set(C).

• Installation •



- 13 -

A


Tools can be kept in the holder provided .

Cutting sticks (A) can be put in the tool holder



- 14 -


A

Plug into socket.The machine must be connected directly to thesocket.


Side tables (A), left and right are available asan option (Nr. 9000 528).



- 15 -

AA

A

AB

X

• Operation •

It is forbidden to operate the machine if theoperating and safety instructions have notbeen understood. Please check the safetydevices are functioning and completebefore use.• All covers have to be mounted (A).• The release for cutting is allowed only if

the cover is closed and the two-hand safetydevice is operated at the same time (B)

• If the front cover closes by itself thegas spring (X) needs replacing.

We recommend you keep a record of your testresults.



- 16 -


B

A

CA

B

D

The measurement is set either with the hand-wheel (A) or by programming (B) the cuttingmeasurements. Measurement is shown on thedisplay in inches or cm (B).

• Operation •

Position the main switch to "I" (A). Insert thekey for the control system and move it to theright (B). Open the safety guard (C). Themachine is now ready for use.

Press S button (D).Machine will automatically go to the startposition.



- 17 -

A

B

C

B

AB

Optical cutting line (A) that indicates the exactposition of the cut. Blade cuts on the frontedge (B) of the light beam. (Only use when noexact cut is required).

• Operation •

Position the paper on the backgauge (A) andside lays left or right (B).To move paper stacks, please use the paperknock-up block (C) provided.(Run backgauge to the front for turning thepaper stack).



- 18 -


A

+ =

+ =

+ =

The clamp moves automatically when cuttingis activated.

The paper can also be pressed in advance.Clamping and cutting is activated by theactuators (A) on the front table.

• Operation •

Cutting sequence with automatic clampingPress down both actuators to step 2

Clamp returnsPress down completely one of the actuators

Pre-clampingPress down both actuators to step 1

The actuator has 2 switching steps:1. pre-clamping2. automatic clamping and cutting

Switch position 1

Switch position 2

- 19 -

A

A

Cutting activation:Press both actuators of the two-handed controlsystem (A) simultaneously and keeppressed until the paper is completely cut.

To interrupt or stop cutting:To interrupt or stop cutting, releaseboth actuators (A) of the two-handed control.

• Operation •

Close the safety guard.



- 20 -


164

5

7

21

3

9

8

8

T

Operating elements

A - Safety two-handed control systemPre-clamping and cutting

B - Overload switch(blade drive/clamp drive/backgauge drive)

C - Backgauge control

D - Main switch

E - Hand-wheel for backgauge setting

F - Key switch

G - Backgauge

H - Side lay left and right

I - Front safety guard

• Operation •

Start machine• Main switch D to position "I", insert the key

F for the control panel and turn to the right.Start screen appearsThe following functions are changeable:BrightnessCM/INCHTouchtone ON/OFFLanguage

• Press START J backgauge G moves tothe rear and searches for the referenceposition, wait until a measurementis shown in the display CIDEAL 4855 = 45 cm, 17.72 inchesIDEAL 5255 = 52 cm, 20.47 inchesIDEAL 6655 = 61 cm, 24.02 inches

• The DIN measurements in cm(A3, A4, A5, A6) and in inch (LD, LG, LT, hLT)are recallable with the respective buttons.

Warning!Before storing or cutting a measurementplease check if the correct measurement scale(cm or inch) see above is stored.For information on how to store see picturebelow left. Is shown on the screen see K.

After 30 minutes the screen switches toenergy-saving modeThe screen is reactivated by touching thekeypad area L.

- 21 -

164

5

7

21

3

9

8

810

T

• Operation •

Cutting activation Warning!

• Run backgauge to the front for turning thepaper stack

• Do not interrupt the upward movement of theblade by performing switching procedures

• Wait until the display is green beforeactivating a cut

• Blade must always be at the top and becovered by the clamp. Do not touch theblade(see safety information on page 34).

Risk of injury!

Cutting to specified dimensions• Press MANUAL• Enter dimension on the numerical key pad L

Measurement is shown in red(If a wrong dimension is entered this can becorrected by pressing the Y button)

• Press START M dimension isapproached, Measurement is shown ingreen

• Insert paper and move by means of thestacking angle J to the backgauge G andside lay on the left H

• Release the cut.

Cut according to markingsPress MANUAL• Adjust the backgauge with the hand-wheel E

to the back• Insert paper and move by means of the

stacking angle I to the backgauge G andside lay on the left H

• Turn the hand-wheel E to the right until themarking on the paper to be cut is below thecutting line indicator

• The further the hand-wheel Eis turned to the right, the quicker thebackgauge moves. If the hand-wheel isturned to the left the backgauge will returnquicker.

- 22 -


T

• Operation •

Eject functionIf EJECT N is pressed instead of START M,after inserting the measurement L, thebackgauge will advance forwards so thatpaper can be removed. Finally the backgaugemoves to the last setting.

Multiple cut• Enter the start dimension on the display L• Advance to the measurement with the

START M• Push the paper to the backgauge G• Press multiple cut O• Multiple cut sign appears top left together

with the value 00.00 P• Enter multiple cut measurement (appears in

red letters)• Press START the backgauge advances

by the multiple cut size• This is repeated everytime a cut is

activated.

Exiting program-mode• Press multiple cut O (yellow).

Multiple cut sign and value are deleted.

- 23 -

TProgrammingThis control system enables you to store 99programs with 99 programmable steps. Onestep represents one measurement. Afterentering the program numbers you are able tochange between several program steps withthe button j and b.First figure on display Q = program number.Second figure on display R = program step.Smallest cutting measurementIDEAL 4855 3,0 cm/1.18 inchIDEAL 5255 3,5 cm/1.38 inchIDEAL 6655 2,5 cm/0.98 inch

Each program step corresponds to onedimension. The indicated program step can beoverwritten at any time. These programsremain stored when the machine is off.

Entering a program• Press PRG. EDIT "Load program no."

appears• Enter program number 01 ... 99, with

(Top number Q on display = programnumber)

• If measurement is shown on the display theprogram is reserved, select another program

• Program step "01 Step" 00.00 R appears.(Second figure on display R = program step.

• Enter dimension, or move the backgauge tothe desired measurement with thehand-wheel E

• Store the measurement ,next program stepappears.

• Enter the next measurement and with Enter store the measurement etc.

• Should the entered program be requiredimmediately press PRG. RUN

• Press Enter • Press START• Escape the program mode press MANUAL

Cancel a program• Press PRG. EDIT• Scroll with PRG until "Delete program no."

appears• Enter Program number• Press Enter • Press Enter .

• Operation •

- 24 -


TAdapting a program when the printer’simprint deviates• Press PRG. RUN "Load program no."

appears• Enter program number 01 ... 99, and with

2 x Enter proceed to Step 1• Correct the cutting position of the

backgauge with the hand-wheel• MODIFY V appears on the screen and the

measurement flashes• To store press MODIFY• Release a cut and turn the paper• If the printer’s imprint deviates it can be

corrected during the first two cuts via thehand-wheel – see above

• Correction is only possible during the firsttwo cuts

• After leaving the PRG. RUN mode theoriginal data is stored again.

Delete a step• Press PRG. EDIT• Enter program number, confirm with Enter • Select program step with the arrow keys

b and j• Scroll with STEP until "Delete step no."

appears, Press 2 x Enter .

Insert a step• Press PRG. EDIT• Select a program, confirm with Enter • Scroll with STEP until "Insert step no."

appears• Enter insert position e.g. 02• Confirm with Enter • Enter a measurement• Store the measurement with • The cutting position can be shown on the

screen with the arrow keys b and j.

Changing a program step• Press PRG. EDIT• Select a program, confirm with Enter • Scroll with STEP until "Load step no."

appears• Enter step position e.g. 03• Confirm with Enter • Enter a new measurement, Store the

measurement with .

• Operation •

- 25 -

T

T

• Operation •

Eject function program• If a short measurement e.g. 30 cm and then

a long measurement e.g. 40 cm is cut at thestart of a program then it is wise to insert anEJECT S after the first cut so that the paperis pushed to the front.

• The EJECT function can be added each timea measurement is entered and ejects beforeadvancing to the next measurement. Whenthe eject function is programmed an "E" Sappears top right in the display.

• Inserting an Eject function subsequently inthe program. Select a program and advanceto the step to be changed with the arrow keysb and j Enter the new measurement andbefore activating the enter button pressEJECT N .

Example of a program eject function• Press PRG. EDIT• Enter program number e.g. 08• Press Enter • 1. Enter program Step e.g. 30 cm• Press Enter • 2. Enter program Step e.g. 40 cm

Press EJECT and with Enter store thedimension.

How the example works• Press PRG. RUN• Enter program number 08• Press Enter ,• Press START, Measurement is approached• Insert paper• Release cut 1• Eject (Ejection is completed, turn the paper)• The backgauge moves to program step 2• Release cut 2

Multiple cut program• Press PRG. EDIT• Enter program number• Enter the 1. program step e.g. start-up

measurement 40 cm• Store the measurement with Enter • Press the multiple cut symbol O• Enter the number of cuts T with the + button

U (max. 15 cuts) followed by the multiple cutsize (cutting width).

• Store with Enter .

- 26 -

IDEAL 4855 • IDEAL 5255 • IDEAL 6655• Blade and cutting stick replacement •

If the cutting quality decreases:• Check the cutting depth (see page 34).• Check the cutting stick (see page 30).• Replace or grind the blade (see page

26 - 34).The blade cannot be ground if the bladeheight is less than 83 mm/3,29 inches.A new blade must be used.The blade may only be ground by a qualifiedsupplier or from the manufacturerKrug & Priester, D-72336 Balingen.

Danger! Risk of injury!The blade is extremely sharp. Do notextract or transport the blade withoutprotection. Changing the blade may only beperformed by trained staff.

- 27 -

3.

2.

1.

Turn the blade depth adjustment screw to theleft until it stops. (Screwdriver found in tool set(A) or tool holder (B).

Close the safety guard (1.). Lower the blade bypressing both cutting actuators (2.). Keep oneactuator pressed and turn off the mainswitch (3.).

• Blade and cutting stick replacement •

- 28 -


B

A

C

The 3 eccentrics are now exposed and shouldbe turned counter clockwise to position "0"with the special wrench and attachableextension pipe (A) (in the tool set). The slotmust correspond to position "0" (B).

Only IDEAL 4855Unscrew the blade screws (C) on the righthand side.


Remove the special wrench .Close the safetyguard, and turn on the main switch until theblade returns to the home position.

- 29 -

4.

2.

B

A

1.

A

2.

1.

3.

Position the main switch to "0" (1.)Remove the 2 blade screws on the elongatedholes (2.). Then put the blade changing tool (A)into place and fasten it to the blade (3.).


Remove 2 blade screws (1.)IDEAL 4855 and 3 blade screws (1.)IDEAL 5255, IDEAL 6655.Loosen the grips (2.) of the blade changingtool (A) lightly and allow the blade to be takendownwards out of the machine (3.). Place theblade into the blade carrier (B) and screw itinto place (4).

- 30 -


Take out the cutting stick with a small screw-driver. If needed the cutting stick can be turnedor exchanged. (The cutting stick can be usedeight times).


Replacing the cutting stick (not the blade).• Turn the blade adjusting screw (A) to the left

until it stops. (Otherwise the first cut will betoo deep).

• Remove the cutting stick according to toppicure.

• Turn the cutting stick (the non-used sidemust be near to the blade) and plug it into theholding bolt. Danger! Risk of injury!

Cutting test after replacing the cutting stick(not the blade)• Insert the paper and release the cut.• If the last sheet of paper is not cut along the

entire length turn the blade adjusting screw(A) ¼ turn to the right.

• If the last sheet is still not completely cutrepeat this process until the last sheet is cutalong the entire length.

- 31 -

2.

1.

A

A

11 mm0.43 inch

C

BB

C

Place the blade to be exchanged with theblade changing tool (A) mounted (1.), into theblade carrier and push it up to the top andscrew it into place with the grips (2.).


Take the exchange blade carefully out of theblade box and screw it to the blade changingtool (A).• Make sure there is a space ot 11 mm or

0.43 inches! (B).• Blade must be covered! (C).

Danger! Risk of injury!

- 32 -


2.

1.

3.

A

2.

1.

Remove all tools and distribute paper alongthe entire cutting length (1.).Turn main switch to position "I" (2.).


Lightly tighten 3 of the 5 blade screws withwashers (1.).Remove the blade changing tool (2.).Lightly tighten the remaining blade screwswith washers (3.).Return blade changing tool to tool holder (A).

Only IDEAL 4855Lightly screw in the right blade screw with thewasher (A) when the blade is lowered.

- 33 -

A

4.

5.

1.

3. 2.

2.

A

1.

Lower the blade by pressing both cuttingbuttons (1.). Keep one button pressed andturn off the main switch (2.).

With the special wrench (A) the 3 eccentricsshould be screwed down (3.)until the paper iscut along the entire length of the blade(The blade must remain parallel, not too deepinto cutting stick).


Turn main switch to position "I" (1.). Blade willreturn to upper position. Tighten the bladescrews (2.) firmly.

- 34 -


A

Clamping BladeOK

OK


Paper cutting test. If the last sheet or severalsheets are not completely cut, gradually turnthe knob for blade depth adjustment (A)¼ turn to the right until the paper is cut alongthe entire length. Do not set too low as bladewill become blunt sooner.

Danger by blade replacement!Blade must always be covered by thepressing bar (see picture below at the left).

- 35 -

DGrease the backgauge (A) control weekly witha grease gun. Advance the backgauge as faras possible to the front. (Use non-resinous oilor grease).Grease the remaining parts twice a year (seepicture).The main switch must be on "0" (B).Remove lower panel (C).Tools in tool set or tool holder.• Remove any paper.• Grease the machine.• Check the 4 joining bolts and 2 pushing bars

for wear (D). If necessary inform your servicepersonnel.

• Mount the machine.

• Maintenance and cleaning •

= Greasing points on the machine.

Danger! Disconnect the mains beforestarting any service work or beforeremoving the cover.

Maintenance work may only be performed bytrained staff.

- 36 -


Safety testThe safety regulations are according to theregulations of the country where the cuttingmachine is operated. The manufacturerrecommends a safety check is made every 5years by an authorised service team.

• Maintenance and cleaning •

- 37 -

A

B

Is the machine plugged in?

Main switch to position "I"? (A)Control system activated? (B)(Turn key to the right)Release a cut see page 19.

• Possible malfuntions •

Machine does not function!

- 38 -

IDEAL 4855 • IDEAL 5255 • IDEAL 6655• Possible malfuntions •

Cut cannot be made.• If cover is open:

close it.• If cover is closed:

open and re-close it. (Security check).



- 39 -

A,B,C

Machine turns off:• Machine overloaded.

Safety button (A) or (B) ejects.(Allow 1 minute cooling time and reset thesafety button (A) or (B).

• Machine blocked.• Blade is blunt.

Eliminate the cause, and push the safetybutton (A).

• Backgauge blockedSafety button (C) ejects.Eliminate the cause, and push the safetybutton (C).

Safety button for:

A = Blade drive

B = Clamping drive

C = Backgauge drive


- 40 -


C

A

B

Does not cut through the last sheet:• Turn or turn around the cutting stick (A),

readjust the blade by means of the bladeadjusting knob (B)(see page 34).

Poor cutting quality or blade stays in thepaper stack.• Change the blade (C) (see pages 26 - 34.




- 41 -

A

C

B


Display illumination off• Machine is plugged in? (A)• Main switch on position "I"? (B)• Push in the safety button! (C)• Check the units fuse and the on-site circuit

breaker!

After 30 minutes the screen switches toenergy-saving modeThe screen is reactivated by touching thekeypad area L.

Motor runs but blade does not movedownwards.• Security brake has been activated!

Inform the Service Team!

None of the above mentioned methodshelped to solve the problem:Contact Service Team under• www.ideal.de "Service"

[email protected]



- 42 -

IDEAL 4855 • IDEAL 5255 • IDEAL 6655• Accessories •

Recommended accessories:

Blade• Nr. 9000 130 IDEAL 5255• Nr. 9000 025 IDEAL 6655

Cutting stick (6 pieces)• Nr. 9000 024 IDEAL 5255• Nr. 9000 026 IDEAL 6655

Blade changing tool 1

• Nr. 9000 512 IDEAL 5255• Nr. 9000 513 IDEAL 6655

Paper knock-up block 1

• Nr. 9000 521

1 Included in delivery

Side tables left and right• Nr. 9000 528

- 43 -

A

• Technical data •

Technical data:• Power supply: 230V/50Hz/1~,

120V/60Hz/1~• Cutting height: 80 mm• Leakage current < 3,5mA• Power cord gauge min. 1,5mm2 (230V)• Power cord gauge AWG 12 (20A) (120V)

The exact technical specifications can befound on the technical specifications sticker(A) on the machine. A wiring diagram isfound in the electrical switch box.To claim under guarantee, the machine muststill carry its original identification label.

Cutting- length

mm

Table- depth mm

Minimum space requirement (B X T X H) mm

Weight kg

IDEAL 4855 475 450 765* x 1000** x 1300 228***IDEAL 5255 520 520 865* x 1135** x 1295 252***IDEAL 6660 650 610 1000* x 1230** x 1295 302***

* with side tables: (Width)IDEAL 4855 1365 mm

** with side tables: (Depth)IDEAL 4855 1060 mm





*** with side tables: IDEAL 4855 237 Kg*** with side tables: IDEAL 5255 261 Kg*** with side tables: IDEAL 6655 311 Kg



- 44 -

IDEAL 4855 • IDEAL 5255 • IDEAL 6655• Technical data •

This machine is approved by independentsafety laboratories and is in compliance withthe EC-regulations 2006/42/EG and2004/108/EG.

Sound level information:Sound measurement to EN 13023 :72,5 db (A)

Subject to alteration without notice.



- 45 -

Krug + Priester has a certified qualitymanagement system according to DIN ENISO 9001:2008 and a certified environmentalmanagement system according to DIN ISO14001:2009.

• Technical data •



- 46 -


4855 GS-ID Nr. 11485002 UL-ID Nr. 104850025255 GS-ID Nr. 11522102 UL-ID Nr. 105221026655 GS-ID Nr. 11655002 UL-ID Nr. 10655002

D EG-KONFORMITÄTSERKLÄRUNGGB EC-declaration of conformityF Déclaration de conformité CE

- Hiermit erklären wir, daß die Bauart von- Herewith we declare that- Par la présente, nous déclarons que

- folgenden einschlägigen Bestimmungen entspricht- complies with the following provisons applying to it- sont conformes aux dispositions pertinentes suivantes

2006/42/EG:Maschinenrichtline, EC Machinery directive, EC Directives machines.2004/108/EG:EMV Richtline, EMV Electromagnetic compatibility directive,EMV directives compatibilité électromagnétique.2011/65/EURoHS Richtlinie, RoHS directive, RoHS directives.

- Angewendete harmonisierte Normen insbesondere- Applied harmonised standards in particular- Normes harmonisées utilisées, notamment

EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2;EN 61000-3-2; EN 61000-3-3; EN ISO 12100; EN 61496-1; EN 61496-2;EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1

Bevollmächtigter für technische DokumentationAuthorized representative for technical documentationReprésentant autorisé pour la documentation technique

Krug & Priester GmbH u. Co KGSimon-Schweitzer-Str. 34D-72336 Balingen (Germany)

29.12.2009 Datum

- Geschäftsführer-

- 47 -

Remarks:



IDEAL • Made in Germany

• Document Shredders •

• Trimmers and Guillotines •



ideal 4855 ideal 5255 - mybinding.com · - 3 - d keine bedienung durch kinder! gb children must not...

Documents