if the quad copter is flying erratically, it can be ... · the quad copter will only remember your...
TRANSCRIPT
Installing controller batteries Battery charging
Flight conditions
3D flip stunt
Troubleshooting
Flight Preparation
Operating Instructions for Flight and Trimming
Installing the blade guards and landing gear
Installing the drone battery
2.4 G 6-Axis Gyro Quad Copter
User Manual
TR - 411 Drone
Please read all instructions carefully before using. Please keep the instructions available for future reference.
Diagram
shell
Blade guard
Remote control instruction:
blade
motor
Antenna Power indicatorHeadless mode
Photo/video button(This function requires a camera.
Camera is not included.)
Turn left/right throttle handle
Up for accelerationDown for deceleration
Turn left/right trimmer
Power switch
Return buttonFlip button
Forward/backward left/right side flight
Forward/backward trimmer
Left/right side flight trimmer
1. Open the battery cover, install 4 AA batteries as shown in the diagram.
Side flight trim
If the drone is drifting left or right duringflight, push the right or left trimbutton until the drone stops drifting.
Forward/backward
trim
If the drone is drifting forward or backduring flight, push the move backward or forward trim button until the drone stops drifting forward or backward.
Ascend/descend
Push the left joystick up for taking off orgoing up. Pull the left joystick down todescend or to land the aircraft.
Problem
The drone is unresponsive. The indicator is flashing
1. Unit not paired successfully2. The drone battery is low
1. Perform pairing again(see pg 3)2. Charge the battery
1. Charge the battery2. Replace the blades
The drone’s rotors spin, but it doesn’t take off
1. Battery power is low2. Blades are damaged
Blades are damaged
1. Blades are damaged.2. Motor is broken.
The flight sensors are out of balance after crash
Turn the drone off for 10 seconds,then pair the device again(see pg 3)
1. Replace the blades2. Replace the motor
Replace the bladesThe drone is shaking when flying
The drone still moves after adjusting the trim
After a crash, the drone is out of control
Cause SolutionRight/left
turningPush the left joystick to the right or left. The craft will turn/spin in the direction that the joystick is pushed.
Forward/backward
Push the right joystick forward or back. The craft will go in the direction thatthe joystick is pushed.
Side flightPush the right joystick to the right or left. The quad will fly to the side in thedirection the stick is pushed.
4 AA batteries(not included)
Figure 1
Figure 1 Figure 2 Figure 3
Figure 2
Battery cover
318.27mm
318.27mm
1 2
distan
ce:
2.5 m
eters
distance:3 meters
distance:3 meters
distan
ce:
2 mete
rsdistance:
3 meters
3 4
Safety precautions
5
①
② battery plug fuselage plug①
Recycle the toys / batteries according to all local laws.
1. This product is intended for users over 14 years old2. Please keep the quad a safe distance from people and animals to prevent injury from the rotating blades.3. Never use this product near an airport area to prevent electromagnetic interference. Do not use this product in areas that prohibit the use of remote control products.4. Never look directly into or shine the light beam into the eyes.5. Motors may become hot during use - avoid touching them.6. Refer to instructions on pg 2 when taking out / installing batteries.7. Never try to recharge non-rechargeable batteries.8. Always charge batteries under adult supervision.9. Install batteries with the correct polarity as shown on pg 2.10. Always remove exhausted/used up batteries from the controller.11. ONLY USE the TopRace provided USB charger to charge batteries.12. Before cleaning the unit, disconnect everything from the charger.13. Before flight, check wires, plugs, etc. Replace them if damaged.
Warning
1. Install the batteries as shown.2. Never mix new batteries with older ones.3. Always use the same type of batteries together.
Aircraft function introduction
Connect the USB chargerto the battery plug
14+Ages
If you have questions about your TR-411, visit us at www.TopRace.comor send us an email at [email protected].
12.5in
12.5in
- Turn the power on the quad copter and place it on a flat surface.- Next, turn on the controller, pull the throttle stick back. LED Indicatorwill flash from slow to fast. Now, push throttle stick forward then backagain.- The RC controller will “beep” and LED will remain solid. This indicatesthat the TR-411 is paired with your controller.- A Low Battery warning will begin flashing when your battery is getting too low. To avoid damage, bring the craft back immediately and recharge.
Use a Phillips screwdriver and install a bladeguard at each of the four blades as shown inFigure 1 above. Tighten the screws provided.
Insert the ends of each landing gear(tripod arms) into the holes in the body of the aircraft as shown in Figure 2 above. Tighten the screwsusing a Phillips screwdriver.
Open the battery cover asshown in Step 1 and 2 above.(Slide it out and then lift up)
Next, carefully connect thebattery plug to the fuselageplug as shown above.
Replace the battery cover asshown in Step 1 and 2 above.(Push down and slide it back in)
To charge, connect the battery to USB chargingplug as shown. The Red LED in the USB plugwill turn on. Once the battery starts charging, the LED light turns off. When the battery is fully chargedthe LED light comes back on to indicate charging iscomplete.
- Only fly outside when the weather is clear with no wind.- To insure control and avoid damage to your TR-411, neverfly in wet and windy weather.- Always make sure you have a clear area for flight. Whenflying inside or outside, do not fly near obstacles, peopleor pets. Note: Minimum space for safe flight is have at least9 feet to either side and in front of you and 8 feet above you.
- The maximum distance for controlling the TR-411 drone is 300 feet. Never tryto fly beyond that distance.- When the battery is installed, the indicator light will be flashing. Place the drone on a flat surface and begin pairing it with the controller.- To pair, pull the throttle stick to the bottom and turn on the controller. Next, push the throttle stick to the topand then back to the bottom. The controller will “beep” once and the indicator stops flashing. This indicates devices are successfully paired.
The TR-411 can perform a variety of flips/stunts. If you press the Flip Button, the controller will “beep” andthe drone will automatically flip forward. If you press the Flip Button and the Speed Button, the controllerwill “beep” three times. Now, you can manually control the direction of your flip by pushing the rightjoystick in the direction you want.
NOTE: When in manual flip mode, you must push the right joystick in more than a 15 degree angle, inorder for the drone to flip in that direction. If you move the stick at less than a 15 degree angle, the dronewill simply fly in that direction.
Visit us at: www.TopRace.com
Headless Mode: : refers to the copter flying according to the transmitter control on ly, regardless of which waycopter is fa cing. For example: if the front of the copter is facing to the side,if it is put in Headless Mode and the control lever is pulled inward, the copter will fly toward you. This is helpful in retrieving the copter if it is beyond your sight.To activate Headless Mode, press the Headless Mode button as shown until you hear two beeps.To remove headless mode, press the button again.One Key Return Mode: If copter is within range of the controller, once the One Key Return button is pressed, the copter will return to the transmitter. To remove One Key Return, press the button again.
NOTE: ONE KEY RETURN and HEADLESS MODE will not work properly if you have moved or changedpositions from the beginning of your flight. The Quad Copter will only remember your initial position and will assume that as the correct spot to return to. In this event, manually return the copter and begin a new flight.
Resetting the DroneIf the Quad Copter is flying erratically, it can be corrected by resetting it to its defaults. To reset, first turn on the transmitter and then power up the drone. Now, steps below:
Next, the TR-411 LED will begin slowly flashing. Now, push the throttle stick all the way forward and then all the way back. As shown above. The LED light will stay lit and stop flashing.
Finally, place the drone on a level surface. Now,push both levers to the bottom right corner, as shown above. The LED lights will begin flashingrapidly. After a few seconds, the lights will return to solid idicating that the TR-411 has beenreset. If this does not work, repeat the process.